Transcript
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 SCHEMATIC SCH03
BATTERY
S O LE NO ID RED
A
RED
STARTER
RED
M
FUSE
AMMETER (OPTIONAL)
B S M A1 L A2
WHITE
BLUE
G
CLUTCH / BRAKE (PEDAL UP)
ATTACHMENT CLUTCH (CLUTCH OFF) BLACK
BLACK
SEAT SWITCH (NOT OCCUPIED)
BLACK
BLACK
GRAY GRAY
REVERSE SWITCH NOT IN REVERSE
SHORTING CONNECTOR
BLACK BLACK
HOUR METER
BLUE
BLACK
(OPTIONAL)
FUEL LINE
CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM
BLUE
RED
SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES)
IGNITION UNIT
BLACK/WHITE
28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)
FUEL SHUT-OFF SOLENOID LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM
LIGHT SWITCH
DIODE
STATOR
ORANGE
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) BROWN
IGNITION SWITCH POSITION
CIRCUIT
OFF RUN/OVERRIDE
M+G+A1 B+A1
RUN START
B+A1 B + S + A1
“MAKE”
L+A2
BLACK
NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST.
3
HEADLIGHTS
NON-REMOVABLE CONNECTIONS
REMOVABLE CONNECTIONS
WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING.
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 ELECTRICAL L09 22
79
21
33 34
30
27 90 26 2
24
43
41
42
27
1
40
91
25 99 100
8
28
55 16 16
102
29
4
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 ELECTRICAL
KEY PART NO. NO.
DESCRIPTION
1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 55 79 90 91 99 100 102
Battery Bolt Hex Hd 1/4-20 unc x 3/4 Box Battery Switch Interlock Harness Socket Light Bulb, Light #1156 Cable Battery Cable Battery Fuse Nut Keps Hex 1/4-20 unc Cable Ground Switch Seat Switch Ign Key/Chain Switch Light/Reset Harness Ign Bolt Fin Hex 1/4-20 unc x 1/2 Cover Terminal Red Solenoid Screw 5/16-18 x 1/2 Socket Asm. Bulb Cover Terminal Strap Battery Screw 1/4-20 x 3/4 Washer 9/32 x 7/8 x 16 Ga. Harness Pigtail Trans. ROS
532 16 34-65 874 76 04-12 532 18 64-91 532 17 61-38 532 18 37-59 532 00 41-52 532 12 47-80 532 14 61-48 532 17 51-58 873 51 04-00 532 14 54-91 532 19 27 49 532 19 33-50 532 41 19-33 532 11 07-12 532 19 74-28 871 11 04-08 532 13 15-63 532 19 25-07 817 49 05-08 532 17 52-42 532 18 04-49 532 19 02-70 817 67 04-12 819 09 14-16 532 19 74-60
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
5
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 CHASSIS
259 264 258
28
263
17 261
10
217
39
18 10 30
58
278
90 31 209
5
159
5 209
11
208
9 209
208
207 64
1
144 209
13
26 60
26
142
143
142 145
37 209
2
37
14
74 206
208
38
209
38
6
14
chassis-stlt_ELITE SV-PRO_2
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 CHASSIS
KEY PART NO. NO. 1 2 5 9 10 11 13 14 17 18 26 28
532 17 46-19 532 17 65-54 532 15 52-72 532 40 51-14 872 14 06-08 532 17 49-96 532 17 52-55 817 49 06-08 532 19 45-88 532 18 49-21 873 80 06-00 532 18 38-28
30 31 37 38 39 58 60 64 74 90 142 143 144 145 159 206 207 208 209 217 258 259 261 263 264 278 --
532 19 46-18 532 13 99-76 817 49 05-08 532 17 57-10 532 40 78-07 532 18 93-50 872 14 06-06 532 15 47-98 873 68 06-00 532 12 43-46 532 17 57-02 532 18 66-89 532 17 55-82 532 40 91-67 532 19 46-22 532 17 01-65 817 67 05-08 817 67 06-08 817 00 06-12 532 19 46-19 532 18 97-55 532 18 97-54 532 18 97-53 532 18 38-33 532 18 38-32 532 41 63-58 532 00 54-79
DESCRIPTION Chassis Drawbar Bumper Hood/Dash Dash P/L Bolt Carriage 3/8-16 x 1 Panel Dash LH Panel Dash RH Screw Thdrol 3/8-16 x 1/2 Hood Bumper Hood Nut Lock Hex w/Ins 3/8-16 unc Grille/Lens Asm (Includes Nos. 258, 259, 261, 263, 264) Fender Bracket Fender Screw Thdrol 6/16-18 x 1/2 TYT Bracket Asm Pivot Mower Rear Bracket Pivot Duct Air Bolt 3/8-19 unc x 3/4 Dash Lower STLT Nut Crownlock 3/8-16 unc Nut 1/4 Plate Reinforcement STLT Bracket Swaybar Chassis Bracket Footrest Rod Pivot Hood Cupholder Bolt Shoulder 5/16-18 Screw Thdrol 5/16-18 x 1/2 Screw Thdrol 3/8-16 x 1/2 Screw Hexwsh Thdr 3/8-16 x 3/4 Console Fuel Window Lens Grille Pro RH Lens Grille Pro LH Insert Grille Bezel Grille RH Bezel Grille LH Screw #10 x .750 Plug BTN BlK
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
7
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 DRIVE
57 120
89
63
212 70
116
219 19 59 221 274 61 224
221
69
19
276
214
222 51
221
251
21
236
227
218
19 263 241232 242 235
240 233
228 273 272 217 244 35
223 226
234
30
52 16
48 27
151 51
49
39
47
223 226
62 221
239 33 239
253
150
38
120
34
36 19
238
202
41
51
237 52 32
64 50
229
223
19
65 56
225 220
96
66
37
36 35 53
6
28
231
26
95 96
19
22
29
55
10 27
25 24 77
252 52
15
32 77 78
1 241
30 74 75
drive-stlt_HYDROGR_pedal_1_r1
76
8
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 DRIVE
KEY PART NO. NO. 1
------
6 10 15 16 19 21 22 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 41 47 48 49 50 51 52 53 55 56 57 59 61 62 63 64 65 66 69 70 74 75 76 77
817 06 05-12 876 02 04-16 874 49 05-44 873 80 05-00 873 80 06-00 532 18 65-71 532 17 58-96 873 35 06-00 532 19 20-36 819 13 13-16 876 02 04-12 532 17 57-65 532 07 16-73 532 16 95-92 874 76 05-12 872 14 05-06 532 17 55-78 532 12 01-83 819 21 16-16 532 12 49-63 532 17 91-14 872 11 06-22 532 17 55-56 532 12 77-83 532 15 44-07 532 12 32-05 872 11 06-12 873 68 06-00 873 68 05-00 532 19 96-52 532 10 57-09 817 06 06-20 532 14 02-94 532 16 96-91 817 12 06-14 532 12 48-72 532 17 54-10 532 17 39-37 810 04 07-00 532 15 47-78 532 14 24-32 532 13 46-83 532 13 70-57 532 12 17-49 812 00 00-01 532 12 35-83
DESCRIPTION Transaxle Hydro gear Model 347-0510 (See Breakdown) Screw 5/16-18 x 3/4 Pin Cotter Bolt Hex Flghd 5/16-18 Gr. 5 Nut Lock Hex w/Ins. 5/16-18 unc Nut Lock Hex w/Wsh 3/8-16 unc Knob Custom Control Cruise Rod, Brake Nut, Hex Jam 3/8-16 unc Spring, Brake Rod Washer Pin Cotter 1/8 x 3/4 CAD. Rod, Parking Brake Cap Brake Parking Bracket, Transaxle Bolt Hex Hd 5/16-18 unc x 3/4 Bolt Rdhd Sqnk 5/16-18 unc x 3/4 Shaft, Foot Pedal Bearing, Nylon Washer Pin, Roll Pulley, Composite, Flat Bolt Rdhd 3/8-16 unc x 2-3/4 Gr. 5 Keeper, Belt Idler Flat Pulley, Idler, V-Groove Bellcrank Clutch Grnd Drw Stl Retainer, Belt Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5 Nut Crownlock 3/8-16 unc Nut, Crownlock 5/16-18 unc Link, Clutch Spring, Return, Clutch Screw 3/8-16 x 1-1/4 V-Belt, Ground Drive Keeper, Center Span Screw 3/8-16 x .875 Cover, Pedal Pulley, Engine Bolt 7/16-20 x 4 x Gr. 5 Washer Keeper Belt Engine Screw Hex Wsh Hi-Lo 1/4-1/2 unc Guide Mower Drive RH Spacer, Axle Washer 25/32 x 1-1/4 x 16 Ga. E-Ring Key, Square
KEY PART NO. NO.
DESCRIPTION
78 89 95 96 116 120 150 151 202 212 214 217 218 219 220 221 222 223 224 225 226 227 228 229 231 232 233 234 235 236 237 238 239 240 241 242 244 251 252 253 263 272 273 274 276
Washer 25/32 x 1-5/8 x 16 Ga. Console, Shift Rod Bypass Retainer Spring 1" Zinc/Cad Bolt 3/8-16 x 1 Nut Lock Flg 3/8-16 unc Spacer Retainer Washer 13/32 x 2 x 10 Ga. Bolt RDHD 3/8-16 unc x 1-3/4 Gr. 5 Nut Hex Flange Lock Link Transaxle Pedal Reverse Arm Control Pedal Reverse Bracket Frest Pdl Ctrl. Hyd Bracket Mtg. Pedal Control Bolt Rdhd Sqnk 3/8-16 unc x 3/4 Nut Crownlock 7/16-14 unc Washer Nylon 11/16 ID x .060 Pedal Forward Arm Control Pedal Forward Bolt Pivot Spacer Cam Reverse Pedal LT Bolt Shoulder 5/16-18 Washer Serrated 5/16 x .75 Strap Torque Actuator Cruise Disengage Pawl Control Cruise Lever Control Cruise Sector Control Cruise Bolt Shoulder 3/8-16 unc 1/44 Bolt Shoulder 5/16-18 Arm Mtg. Cruise Sector Screw Thdrol 5/16 x 1/2 Spring Return Cruise Control Nut Centerlock 1/4-20 unc Bolt Fin Hex 1/4-20 x .75 Screw 5/16-18 x 5/8 Screw 5/16-18 Washer 13/32 x 1 x 16 Ga. Washer .3125 x .615 x 16 Gr. Screw 3/8-16 x .75 Screw, 5/16-18 x 1/2 TT Pad, Reverse Pedal Cover Pedal Forward Clip Retainer .0375
532 12 17-48 532 19 22-59 532 19 56-31 532 12 47-88 872 14 06-08 873 90 06-00 532 17 54-56 819 13 32-10 872 11 06-14 532 14 52-12 532 17 47-35 532 17 94-33 532 17 47-13 532 17 48-39 532 17 47-11 872 14 06-06 873 68 07-00 532 17 48-40 532 17 47-36 532 17 47-12 532 17 49-02 532 17 47-10 532 17 90-32 532 17 64-51 532 40 25-50 532 17 55-70 532 17 48-56 532 17 48-58 532 17 48-57 532 12 89-03 532 17 01-65 532 17 58-07 817 49 05-08 532 17 56-10 873 93 04-00 874 78 04-12 817 49 05-10 817 06 05-16 819 13 16-16 532 17 94-22 817 00 06-12 817 67 05-08 532 17 96-10 532 17 56-46 532 17 80-62
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
9
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 ENGINE
8 2
3
1
14 38
13
10
81 17
17
25
6 5
72
32 31
33
37 112 41
45
33 23
29
4
OPTIONAL EQUIPMENT engine-stlt_bs-2_3
Spark Arrester
10
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 ENGINE
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 8 10 13 14 17 23 25 29 31 32 33 37 38 41 45 72 81 112
Control, Throttle Screw Hex Thd Cut 1/4-20 x 1/2 Engine Briggs Model 441677 Muffler Exhaust Tube LH Exhaust Tube RH Bolt 5/16-18 x 3/4 w/Sems Shield Browning Muffler Gasket Tube Oil Drain Screw 3/8-16 x 1-1/2 Shield, Browning/Debris Guard Control Choke Arrester, Spark Tank, Fuel Cap, Fuel Clamp, Hose Blk Line, Fuel Plug Drain Oil Easy Stem Tank Fuel Screw Hex Wsh Thdrol 3/8-16 x 3/4 Screw Socket Head 5/16-18 x 1 Nut Keps Hex 1/4-20 unc Bushing
532 17 05-51 817 72 04-08 ------532 14 97-23 532 15 99-55 532 16 05-89 532 17 18-77 532 14 66-29 532 16 53-91 532 14 84-56 817 06 06-24 532 16 98-37 532 19 17-17 532 13 71-80 532 17 90-22 532 18 29-02 532 12 34-87 532 14 21-58 532 18 16-54 532 13 92-77 817 00 06-12 532 18 39-06 873 51 04-00 532 12 49-52
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-5). Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
11
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 SEAT ASSEMBLY
1
14 10
8 24
7
5
11 16
6
5 22
15
21
2
12
9
7
25
13 17
8
9
41
seat-stlt_knob_2
12
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 SEAT ASSEMBLY
KEY PART NO. NO.
DESCRIPTION
1 2 5 6 7 8 9 10 11 12 13 14 15 16 17 21 22 24 25 41
Seat Bracket Pivot Seat 8 720 Clip Push-In Nut Hex w/Ins. 3/8-16 unc Spring Seat Cprsn 2 250 Blk Zi Screw 3/8-16 x 1.5 Smgml Washer 13/32 x 1 x 14 Ga. Pan Seat Knob Seat Bracket Mounting Switch Bushing Snap Blk Nyl 50 Id Bolt Rdhd Sqnk 1/4-20 x 1-1/2 Spacer Split 28 x 88 Spring Cprsn Nut Lock 1/4 Lge Flg Gr. 5 Zinc Bolt Shoulder 5/16-18 unc Nut Hex Lock w/Ins 5/16-18 Washer 17/32 x 1-3/16 x 12 Ga. Bolt Shoulder 5/16-18 x 62 Strap Asm Fender
532 18 87-12 532 14 05-51 532 14 50-06 873 80 06-00 532 12 41-81 817 00 06-16 819 1316-14 532 19 55-30 532 16 63-69 532 17 46-48 532 12 12-48 872 05 04-12 532 13 43-00 532 12 12-50 532 12 39-76 532 17 18-52 873 80 05-00 819 17 19-12 532 12 70-18 532 14 06-75
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
13
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 STEERING ASSEMBLY 38 97 34 39 1
41
42 37 37 36 44 88 91 43
71 67
68 46 29
67
8 6
13 2
17 82
65
46 6
87 5
8
32
40
68
87 5
29 4 3
43 11
15 29
33 34 35
10
43 95 8
steering-stlt-LEGND2_3
14
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 STEERING ASSEMBLY
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 8 10 11 13 15 17 26 28 29 30 32 34 36 37 38 39 40 41 42 43 44 46 65 67 71 68 82 87 88 91 95 97
Wheel Steering Axle Asm Spindle Asm LH Spindle Asm RH Bearing Race Thrust Harden Washer 25/32 x 1-5/8 x 16 Ga. Ring Clip #T5304-75 Link Drag Washer Lock Hvy Hlcl Spr 3/8 Spacer Brg Axle Front Nut Hex Flange Lock Shaft Asm Steering Bushing Link Drag Washer 13/32 x 7/8 x 16 Ga. Screw 3/8-16 x .75 Pin Cotter 1/8 x 3/4 Rod Tie Washer Lock Hvy Hlcl Spr 5/16 Bushing Strg Screw Insert Cap Strg Wh Washer 11/32 ID x 2-3/8 OD 12 Ga. Crownlock Nut Adaptor Wheel Strg Boot Steering Dash Washer 25/32 x 1 1/4 x 16 Ga. Extension Steering Shaft Cap Spindle Fr Top Blk Spacer Brace Axle Bolt RDHD SQNK 3/8-16 x 2 1/4 Steering Asm Axle, Brace Bracket Susp Chassis Front Washer Flat .781 x 1 1/2 x .14 Bolt Shoulder 7/16-20 unc Clip Steering Washer Harden .739 x 1.637 x .060 Bolt 5/16-18 unc x 4" L Gr. 5
532 19 45-95 532 18 47-06 532 16 98-40 532 16 98-39 532 12 49-31 532 12 17-48 812 00 00-29 532 17 51-21 810 04 06-00 532 13 65-18 532 14 52-12 532 19 07-53 532 12 68-47 819 13 14-16 817 00 06-12 876 02 04-12 532 19 27-57 810 04 05-00 532 15 50-99 532 15 29-27 532 19 46-03 819 11 38-12 873 54 06-00 532 18 67-37 532 16 96-33 532 12 17-49 532 19 07-52 532 12 12-32 532 41 47-36 872 11 06-18 532 17 51-46 532 16 98-27 532 19 99-78 532 17 39-66 532 17 51-18 532 17 55-53 532 18 89-67 874 78 05-64
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
15
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 MOWER DECK
40 67
68
158
36 40
185
143 144
lu tc h
_m od _7
152 42
_c
159
45 150
40
46
145 184
44
59
56 53
148
52 55 146 54
140 207
21
32
48
31
147 142
30
30 1
134
33
30
207
21
135
21
136
21
134
139
116
21
136
117 119
118 119 117
34 113
118
2 147
116
21
2
23
21 2
142
24 25
138 26
2 28 29 113
130
131
16
129 92
92
15
3
20 149
4
5
27
14
18
18
6 13 19
21
11 8
42_deck_man-t-path_stlt_13
16
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 MOWER DECK KEY PART NO. NO.
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 8
532 18 64-26 872 14 05-06 532 13 80-17 532 16 54-60 532 12 46-70 532 17 80-24 532 19 30-03
11
532 13 89-71
13 14 15 16 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 36 40 44 45 46 48 52 53 54 55 56 59 67
532 19 28-72 532 18 72-81 532 11 04-85 532 17 44-93 872 14 05-05 532 13 28-27 532 15 97-70 873 68 05-00 532 17 75-63 532 10 53-04 532 12 37-13 532 11 04-52 532 17 18-59 819 11 10-16 532 13 14-91 532 17 39-84 532 18 76-90 532 15 35-35 532 40 02-34 872 11 06-12 532 17 34-38 873 90 06-00 532 14 00-88 532 12 47-88 532 13 77-29 532 13 39-44 532 13 98-88 532 18 49-07 532 17 85-15 532 15 50-46 532 12 20-52 532 14 10-43 532 17 15-98
68 92 113 116 117 118 119 129 130 131 134 135 136 138 139 140 142 143 144 145 146 147 148 149 150 152 158 159 184 183 185 207 --
Mower Deck Assembly, 42" Bolt Bracket Asm Fr. Sway Bar 3/42 Bracket Asm Deck 42" Sway Bar Retainer Spring Bar Sway Deck Bolt/Washer Asm. 7/16-20 unf (The following blades are available) Blade Mower 42” Hi-Lift (for bagging and discharging) Shaft Assembly, Mandrel Housing, Mandrel Bearing, Ball, Mandrel Stripper, Mandrel Deck Bolt, Carriage 5/16-18 x 5/8 Bolt, Shoulder Baffle, Vortex Nut Bracket, Deflector Mower 42" Cap, Sleeve 80 x 112 Blk Mower Spring, Torsion, Deflector 2 52 Nut, Push Phos & Oil Shield, Deflector 42" Blk Washer 11/32 x 5/8 x 16 Ga. Rod, Hinge 42" 6 75 W/G Screw Thdrol Washer, Spacer Mower Vented Pulley, Mandrel Nut, Toplock Bolt Carr SH 3/8-16 x 1-1/2 Gr. 5 Pulley, Idler, Flat Nut Lock 3/8-16 Guard, Mandrel, LH Retainer Screw, Thdrol 1/4-20 x 5/8 T Washer, Hardened Bolt, Shoulder 5/16-18 unc Arm Assembly, Pad, Brake Washer, Hardened Arm, Idler Spacer, Retainer Guard TUV Idler Knob
--
DESCRIPTION
532 14 49-59 873 80 06-00 817 00 05-10 532 19 34-06 532 17 48-73 873 93 06-00 819 12 14-14 819 13 13-12 874 78 06-16 872 14 06-08 532 15 69-41 532 15 97-65 532 15 59-86 532 15 97-63 532 15 97-67 532 15 97-68 532 19 57-84 532 15 71-09 532 17 34-41 532 17 34-37 532 17 34-43 532 13 13-35 532 16 90-22 532 16 58-98 819 09 12-10 532 16 96-76 817 72 04-08 872 14 06-14 819 13 14-10 532 19 42-08 532 18 82-34 532 19 42-08 532 19 28-70
V-Belt, 42" Mower Nut 3/8-16 Screw 5/16-18 Bolt, Shoulder Wheel, Gauge Nut Centerlock 3/8-16 Washer 3/8 x 7/8 x 14 Ga. Washer 13/32 x 13/16 x 12 Ga. Bolt 3/8-16 x Gr.5 Bolt 3/8-16 x 1 Pin Head Rivet Bracket Asm Wheel Gauge LH Rear Bar Adjusting Gauge Wheel Bracket Asm Wheel Gauge RH Rear Bracket Asm Wheel Gauge RH Front Bracket Asm Wheel Gauge LH Front Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Cable Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Washer 9/32 x 3/4 x 10 Ga. Clutch Cable 42" Screw Hex Thd Cut 1/4-20 x 1/2 Bolt Rdhd Sqn 3/8-16 unc x 1-3/4 Washer 13/32 x 7/8 x 10 Ga. Pin Cotter 5/16 Bowtie Lock Head Asm Cable Clutch Pin Cotter 5/16 Bow Tie Lock Mandrel Assembly (Includes Housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/ washers not included) 532 18 45-63 Replacement Mower, Complete (Std. deck-Order seperately gauge wheel components Key Nos. 116-119)
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
17
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 MOWER LIFT
29
28
27 25 24 23
7 8
41
5 37
49
38
30 40
1 36
13
50 4
3 26
6 2
11
6 5 4
12 13 19 13
20 15 31 32
13
KEY NO. 1 2 3 4 5 6 7 8 11 12 13 15 16 17 18 19 20 23 24
PART NO. 532 19 84-17 532 19 80-70 532 18 88-22 812 00 00-02 819 21 16-21 532 12 01-83 532 12 56 31 532 17 07-70 532 13 98-65 532 13 98-66 532 12 46-70 532 17 32-88 873 35 08-00 532 17 56-89 873 80 08-00 532 13 98-68 532 19 42-09 532 11 08-07 819 13 10-16
19
20
17 18 20 16
20 15
31 32
lift-rh.1pc.stlt_1
DESCRIPTION Wire Asm Inner/Sprg w/plunger Shaft Asm Lift RH w/Inf Pin Groove 5/16 Dia x 1.875 E Ring #5133-62 Washer 21/32 x 1 x 21 Ga. Bearing Nylon Blk 629 Id Grip Handle Button Plunger Link Lift LH Fixed Length Link Lift RH Fixed Length Retainer Spring Link Front Nut Jam Hex 1/2-13 unc Trunnion Nut Lock w/Wsh 1/2-13 unc Arm Suspension Rear Pin Cotter 7/16 Bow Tie Lock Nut Special Washer 13/32 x 5/8 x 16 Ga.
KEY PART NO. NO.
DESCRIPTION
25 26 27 28 29 30 31 32 36 37 38 40 41 49 50
Spring Retainer Clip Rod Adj Lift Nut Hex Jam 3/8-16 unc Knob Trunnion Bearing Pvt Lift Nut Crownlock 3/8 - 24 Pointer Height Ind. Plug Hole Screw 5/16-18 x 1 Washer 11/32 x 1-1/2 10 Ga. Scale Height Ind. Nut Hex Flange Lock Nut Push
532 12 48-74 532 16 94-84 532 12 69-71 873 35 06-00 532 13 80-57 532 15 02-33 532 16 98-65 873 54 06-00 532 15 50-97 532 12 39-35 817 06 05-16 819 11 24-10 532 15 50-98 532 14 52-12 532 11 04-52
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
18
TRACTOR - - MODEL NUMBER PP21H42 (96011021801), PRODUCT NO. 960 11 02-18 DECALS
7
11
16
4
3
4
7 9 1 18
18 8 6 10 12 15
5 2
14
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 9 10 11 12 14 15
Decal Operation Decal Engine RP Decal Hood LH Decal Side Panel Logo Decal Warning Eng Lym. Decal Cutfinger CE Decal Warning Sym CE Decal Fender Logo Deflector Cutfinger Sym Decal Ins Strg Whl Decal DBA Decal Schematic Decal Tick Mark
53217 83-02 532 18 95-26 532 18 61-64 532 19 55-12 532 19 68-41 532 18 21-66 532 40 03-89 532 17 27-40 532 19 63-57 532 17 27-43 532 12 44-33 532 16 03-96 532 16 88-69
21
19
20
KEY NO. 16 18 19 20 21 --------
PART NO. 532 18 61-63 532 15 97-36 532 15 97-37 532 14 50-05 532 14 08-37 532 19 17-87 532 19 17-86 532 13 83-11 532 16 25-98 532 16 69-60 532 40 36-87 532 41 91-64
DESCRIPTION Decal Hood Rh Decal Hot Muffler Decal Brake/Clutch symb Decal Bat Dan/Psn Decal Saddle Brake Parking Pad Footrest LH Pad Footrest RH Decal Handle Lft Height Adjust Decal Load Limit Decal Bypass Manual Operator's Manual Parts
WHEELS AND TIRES
KEY PART NO. NO.
DESCRIPTION
1
1 2 3 4 5 6 7 8 9 10 11 --
Cap Valve Tire Stem Valve Tire F T 15 x 6 0 - 6 Service Tube Front (Service Item Only) Rim Asm 6" Front Service Fitting Grease (Front Wheel Only) Bearing Flange (Front Wheel nly) Rim Asm 8" Rear Service Tire R T 20 x 10-8 Service Tube Rear (Service Item Only) Cap Axle Blk 1 50 x 1 00 Sealant, Tire (10 oz. Tube)
2
5,8 4,10
7 3,9 6
11
532 05 91-92 532 06 51-39 532 10 62-22 532 05 99-04 532 12 51-21 532 12 49-57 532 12 49-59 532 12 51-22 532 12 20-82 532 00 71-52 532 19 32-68 532 14 43-34
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
19
