Transcript
WORSHIP & HALL Series
WORSHIP & HALL Series
2Way passive, compact, processor controlled loudspeaker system
Hall SB Specifications
0° 330°
0° 30°
330°
60°
-18
300°
-24
-30
-30 90°
240°
120°
210° 180°
-30 dB
270°
240°
210°
150° 180°
0° 30°
330°
150° 180°
500 Hz
250 Hz
0°
0° 330°
30°
30°
-6
-6
-6
-12
-12
-12
-18
60°
-18
300°
-24
-24
-30
-30
dB
270°
-24
120°
210°
-18
300°
90°
240°
150°
330°
60°
dB
270°
125 Hz
300°
30° -6 -12
dB
270°
330°
-6 -12
-24
90°
240°
120°
210°
60°
-30 90°
240°
150°
120°
210°
-18
300°
-24
dB
270°
The SB loudspeaker is a compact device designed to perform in a wide range of public address and sound reinforcement applications. It is a 2Way passive system, consisting of two proprietary 5-inch low frequency driver and one 1-inch high frequency dome tweeter loaded with a 60x60° horn, housed in a vented enclosure.
0° 30°
-6 -12 -18
300°
Audio-Performance Worship &Hall SB
150°
dB
270°
AUDIO PERFORMANCE
240°
210°
150°
180°
180°
180°
1 kHz
2 kHz
4 kHz
0° 330°
30° -6 -12 -18
300°
60°
-24 -30 dB
270°
90°
240°
Horizontal Vertical
The enclosure is black, white or any RAL epoxy painted (on option) and fitted with M8 screws on top and bottom and on each side. On the back, two Speakon connectors allow easy parallel connection. The front of the speaker is protected by a perforated metal grill and inside covered with charcoal grey foam.
The SB loudspeaker is designed to operate with the P212 SB-E processor, unit which contains speaker sense, drivers protection, amplitude and phase response alignement circuitry, optimized for this loudspeaker. The P212 SB-E processor allows the loudspeaker to be operated at full capacity with maximum fidelity and reliability. The P212 SB-E is a two channels processor with an optionnal SUB board controller for low frequency reproduction with the AP range of subwoofer’s.
IDEAL FOR Theatres Radios, TV Clubs, Discos Restaurants, Bars Conference rooms Churches, Stadiums Sound Effects Multi Media
120°
210°
150° 180°
8 kHz
AUDIO PERFORMANCE
Special Features high efficiency low distortion electronically controlled AUDIO PERFORMANCE
Audio-performance route de cossonay 36C CH-1040 echallens switzerland
development & manufacturing of professional loudspeaker system & electronics TEL +41 21 886 1050 FAX +41 21 886 1059 email
[email protected]
audio-performance route de cossonay 36C CH-1040 echallens switzerland
develpment & manufacturing of professional loudspeaker system & electronics TEL +41 21 886 1050 FAX +41 21 886 1059 e-mail
[email protected]
WORSHIP & HALL Series
WORSHIP & HALL Series
Hall SB Specifications
Ultra compact system
P212, 2 Channels, 2 Way analogue Processor Acoustical frequency response (1) 55-18'000 Hz ± 3dB
power handling 140W (AES) (4)
max. peak SPL (2) 119 dB
crossover frequency (3) 3500Hz, 24dB per octave
Transducers LO section 2 x 5", long excursion, low distortion cone driver
system nominal impedance 4 or 16 Ohms
HI section 1" dome tweeter, fabric diaphragm loaded with horn
connectors IN / OUT (loop): Neutrik SPEKON NL4MP 1+, 12+, 2-, linked
The Audio Performance P212 SB is an advanced electronic Processor which will optimise the performance of the Audio Performance SB2 passive loudspeaker system. The P212 SB contains an electronic processor with frequency response phase alignment circuitry, analogue delays and Audio Performance's exclusive Sense Inputs driver protection circuitry, incorporating true RMS signal limiting. Sense Inputs driver protection circuitry protects the loudspeaker components from damage due to overheating under high power conditions
This circuit continuously monitors the power applied to the drivers and limits the controller outputs when the safe operating limits of the drivers are exceeded. Until the onset of overload, the Sense Inputs driver protection has no effect on the signal. Operating at line level, the P212 SB is the final component in the signal chain before the amplifier. A high pass-filter can be switched to increase the intelligibility for speech applications. An optional plug-in subwoofer module allows the user to increase the low frequency response of the system, down to 45 Hz
Specification & electrical data Mechanical data cabinet 10 liters, vented mounting system four fasteners M8 screws (top/bottom & sides) AP-U-SB (vertical), C-SB (horizontal) or U-SBS (speaker stand) brackets.
finish rounded edges and corners, the outer surface is hardwearing painted (black, white or any RAL colour) front metal grill. cabinet size (W x H x D) 180 x 450 x 225mm weight 7 kg
Options
Front panel
Rear panel
POWER: Main switch with Power On indicator: green Led
MAIN: Main input with fuse holder and internal voltage switch for 115 - 230 V operation
SUB EQ switch: Off: SB2 outputs full range, On: SB2 LOW CUT switch: Off, On
INPUTS: XLR 3pin, 20KW electronically balanced, maximum level +20dBu. Pin 1: GND, Pin 2: +, Pin 3 OUTPUTS: XLR 3pin, 50W electronically balanced, maximum level +20dBu. Pin 1: GND, Pin 2: +, Pin 3 -
LIMIT: Red's LED for SB2 and Sub SENSE INPUTS: SPEAKON NL4MP 4pin 100KW electronically balanced.
Mechanical data
AP-C-SB, U-SB or U-SBS brackets RAL colour Magnetic shielding
In the interest of improving the equipment, AUDIO PERFORMANCE reserves the right to alter the specification without prior notice. AP/pac/September 2008
dimensions: 19", 1U (483 x 45 x 310mm) W x H x D weight: 5.5 kg
shipping dimensions: 530 x 65 x 430mm W x H x D weight: 6.5kg
In the interest of improving the equipment, AUDIO PERFORMANCE reserves the right to alter the specification without prior notice. AP/pac/Jully 2006
