Transcript
CD-LRMAS-01
PRODUCT OVERVIEW
LRM-AS
Product
Description
Dimmer
The Evolve Wall Mounted Dimmer is a component of the Evolve lighting control system. It is fully scene capable and can handle loads of up to 500W for control of permanently installed lighting fixtures only (not for control of receptacles). The Evolve Wall Mounted Dimmer is easily wired in place of a standard wall dimmer in any existing environment. Inclusion of this Dimmer on a Z-Wave network allows remote ON/OFF control and dimming of loads connected. This device is compatible with Z-Wave security systems and the Auto-Sense feature allows for local lamp activation independent of the Z-Wave controller status. This Wall Mounted Dimmer is designed to work with other Evolve enabled devices. Evolve nodes of other types can be included in the network and will also act as repeaters to increase the range of the network. The Dimmer also has a replaceable trim ring available in assorted colors. As part of a Z-Wave network, the LRM-AS will also act as a wireless repeater to ensure that commands intended for another device in the network are received. This is useful when the device would otherwise be out of the radio range of the wireless controller.
Specifications
• • • • • • •
SKU: LRM-AS Supported Networks: - Z-Wave – Signal (Frequency) 908.42 MHz Range: Up to 100 feet line of sight between the Wireless Controller and/or the closest Evolve Receiver Module Power: 120 VAC, 500W, 60 Hz Dimensions: 4.5” H x 2.75” W x 1.75” D Weight: 0.33 lbs. Requires a Neutral
CD-LRMAS-01 Wiring
PRODUCT OVERVIEW
The LRM-AS is wired in the same fashion as a conventional digital switch – it requires a minimum of 3 wires to operate:
• • •
Black – represents the line input, 120VAC White – represents the neutral Blue – represents the load (switch leg)
The switch also has a green wire which serves as the ground.
WD500Z-1
In the case of a 3-way or 4-way circuit,Radio traveler wires are not when building Evolve Z-Wave Frequency (RF)used Controlled, 500W,an120 VAC network. Instead, an LRM-AS may be used in conjunction with an LTM-5 to create a wireless, Wall Mounted Dimmer, Series 300 “virtual” 3-way. See LTM-5 for further details.
NEUTRAL 120 VAC LINE
WHITE BLACK
BLUE
LOAD
PUSH ON/HOLD TO BRIGHTEN YELLOW (NOT USED) CAP YELLOW WIRE A.G. SWITCH IN - OPERATION OUT - CHANGE LOAD
SUPPLIED WITH DECORATIVE SWITCH PLATE
SCORED TAB WILL BREAK FLUSH WITH EDGE OF PLASTIC
PUSH OFF/ HOLD TO DIM GREEN
GROUND
STATUS LED PUSH TOP OR BOTTOM OF PADDLE SWITCH TO CONFIGURE
NOTE: This module must be “included inWith the Network” onlyoff, where it will permanently installed. The diagram proper operation of this node in the the power wire thebe LRM-AS according to the shown. Caution! Do not wire unit Installation mesh network is dependent on it knowing its location with respect to other nodes. “test bench” configure thistomodule. “live” (with power on the circuit) andYou docannot not allow the yellow wire contact line voltage, neutral or ground or you will damage the device.
WD500Z-1 WALL MOUNTED
If more than one LRM-AS is to be installed in a wall box, scored tabs on the side can be broken with pliers to accommodate proper fit. Apply power when DIMMERoff by bending back and forth INSTALLATION completed.
Linear’s family of Z-Wave certified wireless lighting controls (switches, dimmers, outlets and plug-in modules) brings a new level of intelligent wireless capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote home automation, security and other applications. Embedded in each device, the Z-Wave smart chip enables two-way RF communication among hundreds of Z-Wave enabled devices, allowing products and services from multiple manufacturers to work seamlessly. Linear Z-Wave products are easy to install, and allow dealers to create an integrated wireless network with nearly limitless expansion and interoperability with security and health monitoring systems, energy management, home entertainment, appliances, and more. DANGER! SHOCK HAZARD. Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation. Make sure the total load controlled does not exceed 1800 watts. For indoor use only. Retain instructions for future use. CAUTION: To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle,
With power off, wire this WD500Z-1 according to the diagram show. Caution! Do not wire unit “live” (with power on the circuit) and do not allow the yellow wire to contact line voltage, neutral or ground or you will damage the device. If more than one WD500Z-1 is to be installed in a wall box, scored tabs on the side can be broken off by bending back and forth with pliers, to accommodate proper fit. Apply power when completed
Remote Control The WD500Z-1 will respond to BASIC and MULTILEVEL commands that are part of the Z-Wave system. Refer to your controller’s instructions as to whether your controller can transmit those commands.
All On/All Off
The WD500Z-1 supports the ALL ON/ ALL OFF commands. The WD500Z-1 can be set to respond to ALL ON and ALL OFF commands 4 different ways. Refer to your controller for information on how to set the WD500Z-1 to operate in the manner you desire. Some controllers may be only able to set certain settings of ALL ON/ALL OFF response. The 4 different ways the WD500Z-1 can be setup to respond to ALL ON and ALL OFF commands are: • WD500Z-1 will not respond to ALL ON or the ALL OFF command.
