Transcript
GE Monogram® 42" Built-In Side-by-Side Refrigerator
ZISB420DH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator
ZISB420DH
OVERALL DIMENSIONS
FLUSH INSET INSTALLATION 25 7/8" (65.7) 20 5/8" (52.4)
44" (111.8) 11 5/16" (28.7)
13 1/2" (34.3)
*72 3/16" (183.4)
*83 1/2"
* 83 1/2" (212.1)
(212.1)
68 13/16" (174.8)
*40"
(101.6)
SPECIFICATIONS Overall Width
44" (111.8 cm)†
Overall Height
83 1/2" (212.1 cm) †
Overall Depth
25 7/8" (65.7 cm) †
Door Clearance
28 5/8" (72.1 cm)
Cutout Width
45" (114.3 cm)
Cutout Height
84 1/2" (214.6 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
725 lb (328.9 kg)
*3 3/8" *3"
FRONT VIEW
(8.6)
(7.6)
SIDE VIEW
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84".
41" (104.2) Case width
**13"
**15"
(33.0)
(38.1)
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
26 5/8"
*115° Door swing
(67.6)
Doors can be adjusted to 90° door swing
** Allow 4" (10.2) min clearance to a wall for 90˚ door swing
TOP VIEW
** Allow 4" (10.2) min clearance to a wall for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
ZISB420DH
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator FLUSH INSET INSTALLATION 3/4" PANELS
Case 3 1/4"
(8.3) Finished cleats
20" (50.8)5 1/4" (13.3) 6"
20 15/16" (53.2) *83 1/2" min Depth to cleat *84 1/2" max
24" (61.0) 1 1/2"
Door
E 5"
(12.7)
45" (114.3) Flush inset width 43 1/2" (110.5)
3/4" (1.9)
Width of side cleats
Width between cleats
6"
75"
84 1/2"
19"
75"
(190.5 ) From floor to bottom of electrical area
(214.6)
5"
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
(48.3)
(12.7)
84 1/2"
(214.6)
B Water supply area. WARNING:
5"
(190.5 ) From floor to bottom of electrical area
Finished cleats
A
E
(15.2)
5" 3 1/2"
(12.7)
(12.7)
(8.9)
WATER
3 1/2" 7"
7"
(17.8)
FRONT VIEW
(17.8)
B
3 1/2"
W
(8.9)
FRONT VIEW
Anti-tip Bracket 2" x 4"
SOFFIT
Cut to 35" Length
D
FLUSH INSTALLATION ZISB420DH
Screws mounted into vertical wall studs
*84"
(213.4) *Or installation height from floor
SIDE VIEW INSTALLED UNDER SOFFIT
W 3 1/2"
SIDE VIEW (8.9)
WATER
C
NOTES A M ounting the junction box in this location will also allow for front accessability through access panel.
1/2" (1.3)
3/4" Panel
(212.1-214.6) *Trim will overlap additional 7/16"
SIDE VIEW
7/16" (1.1) Trim overlap
(3.8)
Case Trim
26 3/16" (66.5) Flush inset depth
FLUSH INSET INSTALLATION
TOP VIEW
47 1/2" (120.7)
(15.2)
ZISB420DH
(8.9)
The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. Determine your installation construction and required anti-tip configuration: C C ut a 1/2” x 4” block 35” long. Measure and mark under the soffit, 5 1/4” from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84”. D W ooden Wall Studs and No Soffit • Cut a 2” x 4” block and secure to brackets provided. • Secure brackets to back wall of opening at 84” or your installation height from the floor. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH WOODEN WALL STUDS AND NO SOFFIT
ZISB480DX Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator FLUSH INSET 3/4" PANEL DIMENSIONS
Dispenser Cutout
NOTES
1/4" Router Cut Depth for Hinge Clearance
B
Grille Panel D
FLUSH INSET INSTALLATION
PANEL ASSEMBLY CROSS SECTION
A
Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled 3/4” custom door and grille panels are required. Adjustment brackets allow 1/8” fine adjustment of panel position in 3 dimensions. Use templates provided to locate mounting brackets on the door and grille panels.
Door
E
3/4" Flush Inset Panel
F
PANEL ASSEMBLY CROSS SECTION
HINGE CLEARANCES ROUTER 1/4" DEEP
G
C
Freezer Panel
Maximum total panel weight: • Fresh food door panels – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs
HINGE CLEARANCE
Z Fresh Food Panel
Y
X
X
Y
Z
1 1/4"
1"
1/2"
B
44"
C
D
10 5/8" 68 13/16" 16 7/8"
Dispenser Cutout
15 3/8" (39.1)
Door Handles Door handle not included. A custom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4” panels. Kit includes one handle – 30 1/2” long.
PANEL DIMENSIONS A
ZISB420DH
E 26 7/8"
ZKHSS2: European tubular stainless steel handle designed to fit 3/4” panels. Kit includes one handle – 64 1/4” long.
DISPENSER CUTOUT POSITION F
G
18"
3 7/16"
9 5/8" (24.4)
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator DISPENSER TRIM
ZISB420DH FLUSH INSET INSTALLATION NOTES
Freezer Door
These refrigerators are supplied with a dispenser trim for flush inset panels. Ice/Water Dispenser
A 3/4" Flush Panel
3/4" OVERLAY PANEL DISPENSER TRIM
3 /4" Panel Dispenser Trim: The provided dispenser trim is designed to fit a total panel thickness of 3/4".
• If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim.
A
• If the panel is more than 3/4" thick, the dispenser trim cannot be secured to the door.
RAISED PANEL DESIGN ON DISPENSER MODELS
• T he overlay panel must be constructed according to the specifications shown to achieve the correct total thickness. •W hen a raised panel design is to be used, a custom middle rail is required.
3/4" Flush Panel
16 3/4" 3/4"
B
Total Thickness
C
10 5/8"
Raised Panel Design on Dispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. B
• The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
C
• The middle rail must be 3/4” total thickness to accept the dispenser trim.
DISPENSER TRIM SIDE VIEW CROSS SECTION (Showing Raised Panel with Middle Rail)
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator
ZISB420DH
OVERALL DIMENSIONS
STANDARD INSTALLATION 25 1/2" (64.8) 25 1/2" (64.8) 23 7/8" (60.7) 23 7/8" (60.7)
42" (106.7) 42" (106.7) 1 3/4" 1(4.4) 3/4" (4.4)
13 1/2" 13(34.3) 1/2" (34.3)
*83 1/2" *83 1/2" (212.1)
*84"
*84" (213.4) (213.4)
(212.1)
*72 1/4" *72 1/4" (183.5)
68 1/2" 68 1/2" (174.0)
(183.5)
(174.0)
*40"
*40" (101.6) (101.6)
SPECIFICATIONS Overall Width
42" (106.7 cm)
Overall Height
84" (213.36 cm)
Overall Depth
25 3/8" (64.453 cm)
Door Clearance
28 5/8" (72.1 cm)
Cutout Width
41 1/2" (105.4 cm)
Cutout Height
83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
725 lb (328.9 kg)
*3 3/4" *3(9.5) 3/4" (9.5)
*3 1/2" *3(8.9) 1/2"
FRONT FRONT VIEW VIEW
* Shipping height. Use leveling legs and wheels for maximum * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. 1" height adjustment from shipping height.
(8.9)
SIDE SIDE VIEW VIEW
41" (104.2) 41" Case (104.2) width Case width
** Allow 13" (33.0) min **clearance Allow 13"for(33.0) 130˚min clearance door swingfor 130˚ door swing
** Allow 19" (48.3) min **clearance Allow 19"for(48.3) 130˚min clearance door swingfor 130˚ door swing
ATTENTION ELECTRICIAN:
26 5/8" 26(67.6) 5/8"
A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
(67.6)
TOP TOP VIEW VIEW ** Allow 4" (10.2) min ** Allow 4" min90˚ clearance to a(10.2) wall for clearance toswing a wall for 90˚ door door swing
** Allow 4" (10.2) min ** Allow 4" min90˚ clearance to a(10.2) wall for clearance toswing a wall for 90˚ door door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door ** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow full 130° door swings for pan removal. If the 90° door stop position is used, pan access is full 130° door swings for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary dueZISB420DX to manufacturing tolerances.
ZISB420DX
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator
ZISB420DH
STANDARD INSTALLATION
STANDARD INSTALLATION TOP VIEW 24" (61.0)
47 1/2" (120.7)
3 1/4" (8.3)
20" (50.8) 6" 24" (61)(15.2)
3 1/8" (7.93)
1 9/16"
(3.8)
E
A M ounting the junction box in this location will also allow for front accessability through access panel.
41 1/2" (105.4) 20" (50.8) A
7/16" (1.1) Trim overlap 5"
(3.97)
NOTES
7/16" (1.1) Trim overlap
1 1/2"
(12.7)
6"
*83 1/2" min *84 1/2" max
E
(15.24)
(212.1-214.6) *Trim will overlap additional 7/16"
B Water supply area.
5"
WARNING:
(12.7)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
75"
(190.5 ) From floor to bottom of electrical *84 1/2" (214.6) area *Trim will overlap additional 7/16"
5"
75"
(190.5 ) From floor to bottom of electrical area
5" 3 1/2"
(12.7)
(12.7)
(8.9)
5"
(12.7)
WATER 3 1/2"
5" 3 1/2" (8.9) W
(12.7)
B
(8.9)
FRONT VIEW W
WATER SIDE VIEW
FRONT VIEW
SIDE VIEW
3 1/2" (8.9) The refrigerator will project forward, slightly beyond adjacent cabinetry.
Anti-tip Bracket 2" x 4"
C
SOFFIT
Cut to 35" Length
D
STANDARD INSTALLATION ZISB420DH (213.4) *84"
E 3/4" Min.
*Or installation height from floor
Top Case Trim
Side View Top Case Trim
Install Screws Through Trim and Into 3/4" Min. Wood Brace
SIDE VIEW INSTALLED WITH WOODEN WALL STUDS AND NO SOFFIT
ZISB480DX
Determine your installation construction and required anti-tip configuration: C Installed Under Soffit After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exeed 24” deep. The top case trim overlaps the bottom of the soffit. D W ooden Wall Studs and No Soffit • Cut a 2” x 4” block and secure to brackets provided. • Secure brackets to back wall of opening at 84” or your installation height from the floor.
Screws mounted into vertical wall studs
SIDE VIEW INSTALLED UNDER SOFFIT
The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions.
FRONT VIEW INSTALLED WITH METAL WALL STUDS AND NO SOFFIT
E M etal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a ¾” minimum wood brace above unit, with it’s front surface 24” from back wall. • After installing unit into opening, raise grille panel and attach metal case top trim to ¾” minimum wood brace. • The brace spanning the enclosure must be securely fastened to cabinets on both sides. See Installation Instructions for detailed instructions.
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator CUSTOM SIDE PANELS
ZISB420DH STANDARD INSTALLATION
F
24" (61.0)
NOTES
3/16" (.5)
1 7/8" (4.8)
*84” *84"
(213.4) *Depending on installation height
F S ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
*3" - 4"
(7.6 - 10.2) *Depending on installation height
2 9/16" (6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator 1/4" FRAMED PANEL DIMENSIONS
STANDARD INSTALLATION NOTES
PANEL ASSEMBLY CROSS SECTION
A
D
Trim
B
Grille Panel
Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required.
Door
E 1/4" Framed Panel
Supplied Handles
Dispenser F Cutout
PANEL DIMENSIONS G
C
Fresh Food Panel
Freezer Panel
ZISB420DH
1/4" Framed Panel
Dispenser Cutout
A
B
C
39 7/8"
9 1/2"
68 3/8"
D
E
14 9/16" 24 9/16"
1/4” Framed Panels: Order trim kit #ZKT42SSH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs
DISPENSER CUTOUT POSITION
15 3/8" (39.1)
F
G
17 13/16"
3 1/8"
9 5/8" (24.4)
3/4” Overlay Panels: Order trim kit #ZKT42SSH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
3/4" OVERLAY PANEL DIMENSIONS
B
Grille Panel D Dispenser Cutout
The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.
PANEL ASSEMBLY CROSS SECTION
A
E
Trim
Door
1/4" Backer Panel
Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
3/4" Overlay Panel
.10" Spacer Panel
F
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
Supplied Handles
PANEL DIMENSIONS G
Freezer Panel
C
Fresh Food Panel
A
B
C
1/4" Backer Panel
39 7/8"
9 1/2"
68 3/8"
.10" Spacer Panel
39"
8 5/8"
67"
3/4" Overlay Panel
40 1/8"
9 3/4"
D
E
14 9/16" 24 9/16" 13 1/4"
23 1/4"
68 5/8" 14 13/16" 24 13/16"
.25" + .10" + .75" = 1.10" Total Panel Thickness
Dispenser Cutout
9 5/8" (24.4)
15 3/8" (39.1)
*DISPENSER CUTOUT POSITION F
G
17 15/16"
3 1/4"
Maximum total panel weight: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle. Order 2 kits for sideby-side refrigerators from your Monogram suppplier.
* Cut the dispenser opening after the backer, spacer and overlay panels have been assembled.
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator DISPENSER TRIM
1/4" Framed Panel
ZISB420DH STANDARD INSTALLATION
Freezer Door
1/4"
Total Thickness
1.10"
Freezer Door
1/4" Backer Panel
Total Thickness
.10" Spacer Panel
Ice/Water Dispenser Ice/Water Dispenser
3/4" Overlay Panel
1/4" PANEL DISPENSER TRIM
3/4" OVERLAY PANEL DISPENSER TRIM
A
B
NOTES These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels. 1/4" Panel Dispenser Trim: The framed panel must be 1/4” nominal thickness to fit the dispenser trim. • The dispenser trim fits over the custom panel and snaps into the freezer door. • If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.
1/4" Backer Panel .10" Spacer 3/4" Overlay Panel
3/4" Overlay Panel Dispenser Trim: The 3/4” overlay dispenser trim is designed to fit a total panel thickness of 1.100".
16 3/4" 1.10”
C
Total Thickness
D
• If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim. • If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door.
10 5/8"
DISPENSER TRIM
• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.
SIDE VIEW CROSS SECTION (Showing Raised Overlay with Middle Rail)
• A lternative panel construction methods such as securing a 3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required 1.100" panel thickness. • When a raised panel design is to be used, a custom middle rail is required. Raised Overlay Panel Design on Dispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. • The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. • The middle rail must be 1.10” total thickness to accept the dispenser trim.
Product Specification Created 8/14
GE Monogram® 42" Built-In Side-by-Side Refrigerator
ZISB420DH
FEATURES AND BENEFITS Halogen Light Columns - Located in the freezer and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination LED Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space Advanced Temperature Management System with Multi-Shelf Air Tower - Provides even distribution of air throughout the refrigerator Climate-Control Drawer - Allows you to expresschill beverages, express-thaw meats and select specific temperatures for perishable foods Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness Filter-Change Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser GE® Water Filter - Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight Drop-Down Shelf - Provides additional space for a casserole dish or pizza box
R
Product Specification Created 8/14
