Transcript
VEHICULAR SWING GATE OPERATOR
Commercial DC
Model CSW24VDC
1
Gate Operator and Accessory Site Plan 2 1 2 3 4 5 6 7 8 9 10 11
MyQ® Enabled Indoor Controls Remote Controls Photoelectric Sensors Loop Detectors Lock Mounting Plate Solar Batteries Heater Swivel Arm dwellingLIVE
1
2
11
828LM*
5
Internet Gateway Imagine your Customers being at the office and receiving an alert if they left their garage or gate open. Or being able to turn on their lights before they get home. The 828LM Internet Gateway, which connects to your Customer’s router and enables smartphone control, does this by letting them monitor, open and close their garage door or gate from anywhere and control home lighting.
LiftMaster Elite Series® Maglock (MG1300) Securely holds the gate in the closed position keeping unwanted visitors out. (1300 lb holding force)
892LT & 894LT
6
These remote controls are ideal for gated communities. One button can control a gate operator and the other(s) can control a garage door. It can also be programmed to different codes and frequencies.
For post mounting model CSW24VDC commercial slide operator. Posts not included.
7
Ideal for remote and sunny areas without access to an AC outlet. Two required.
SOLPNL10W12V 10 Watt 12V Solar Panel Two required.
8
Standard 7 AMP-Hour Battery, 12 Vdc, to replace original batteries provided with operator. Reuse existing harnesses.
These remote controls are ideal for applications such as gated communities or commercial applications requiring a large number of remotes for a common entrance.
3 3
A12330SGLPK 33Ah 12V Battery Upgrade 33 AMP-Hour Battery, 12 Vdc. Ideal for solar applications and extended battery backup. Two required.
CPS-RPEN4GM Photoelectric Sensor (Monitored) The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the operator. Includes mounting brackets.
9
6
8
9
Low power through beam photoelectric sensors, 45 foot sensing distance, NEMA 4 rated. Works in conjunction with Power Management System to save power.
4
LiftMaster gate operators comply with UL 325 standards. Important: To be compliant with UL 325 and industry safety guidelines, qualified monitored external entrapment protection devices such as photoelectric sensors or edge sensors are required to be installed with this operator.
4
ORDER SUMMARY Customer:
Date:
Project: Architect/Engineer: Contractor: Gate Length (ft.): Power Source (120 or 240 VAC): LiftMaster.com
Gate Weight (lbs.):
HTR Heater Kit Heater kit for pad mount operators. Protects system to -40ºF. Installs on operator frame.
CPS-UN4 Photoelectric Sensor (Monitored)
29-NP712 7Ah 12V Battery
811LM & 813LM
7
SOLPNL20W12V 20 Watt 12V Solar Panel
Universal DIP Single-Button and 3-Button Remote Control
10
MPEL Mounting Plate for Post Mounting
2-Button and 4-Button Security+ 2.0™ Learning Remote Controls
5
MG1300 Magnetic Gate Lock
10
K75-50292 Swivel Arm Swivel arm for uphill swing gate applications.
11
dwellingLIVE Advanced Visitor Management and Access Control Solution
LOOPDETLM
• Credentialed Access
Plug-In Loop Detector
• Visitor Management
Plug-in Loop Detector, (LOOPDETLM) innovative design includes 8 sensitivity settings & boost, ensures vehicles are easily identified.
• Telephone Entry Systems • License Plate Recognition • Community Websites • Mobile Patrol • Front Desk Concierge
Solar (Y/N): * LiftMaster® Internet Gateway Accessory functionality is dependent on communication with a MyQ® Enabled gate operator. MyQ® Technology communication can be limited by distance and type of exterior building materials. A general range estimate is 300 ft.
VEHICULAR SWING GATE OPERATOR
Commercial DC
Model CSW24VDC TYPICAL INSTALLATION
Installation Blueprint INSTALLATION DIMENSIONS
OPERATOR POWER SOURCE
NOTE: One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists at either the opening or closing direction. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving.
Wire Gauge
120 Vac
240 Vac
14
130 feet
260 feet
12
205 feet
410 feet
10
325 feet
650 feet
8
520 feet
1040 feet
6
825 feet
1650 feet
4
1312 feet
2624 feet
OPERATOR DIMENSIONS
DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR STANDARD INSTALLATION NOTE: There should only be a maximum of 4" (10.2 cm) from the center of the hinge to the edge of the post or column. If the distance is greater than 4" (10.2 cm) entrapment protection for this area is required. 4" (10.2 cm) maximum Outside Property
Hinge Center 46"
27.66" 2" 25"
11"
NOTE: Use copper conductors ONLY.
SINGLE GATE
35.5" Long Arm Inside Property 10"
Warning Sign
29.5" Short Arm
28"
18.77" 14.8"
24"
Concrete Pad
Edge Sensor
Photoelectric Sensors
CONCRETE PAD AND OPERATOR ATTACHMENT CONDUIT LOCATION
5.5"
4 Concrete Anchors 1/2" x 3 1/2"
Operator
4.5"
13.6" 12.2" 6.1"
6.5" 4"
Earth Ground Rod
(Conduit)
Check national and local codes for proper depth
MOUNTING FOOTPRINT
1"
1.5"
3" 2.49"
10" 28"
Water Tight Conduit (Not provided) NOTE: Power and control wiring MUST be run in separate conduits.
Below the frost line. Check all national and local codes.
DUAL GATE
14"
20"
6" Above Ground
15"
28"
(Pad) 24" 24"
Warning Sign
14.82" (cover mounting distance)
Edge Sensor
SAFETY LAYOUT Warning Sign Operator
Monitored Photoelectric Sensors
Edge Sensor
(Outside Property)
Operator Photoelectric Sensors
NOTE: Wired connection in a dual gate setup is optional. Operators can be setup for wireless dual gate communication.
Water Tight Conduit (Not provided) Earth Ground Rod Check national and local codes for proper depth
© 2014 LiftMaster All Rights Reserved 845 Larch Ave., Elmhurst, IL 60126 LiftMaster.com 01-37415B
NOTE: Power and control wiring MUST be run in separate conduits.
NOTE: Entrapment protection is required for the area between the open gate and the operator. (Inside Property)
Sensors for Close Cycle
