Transcript
INSTALLATION INSTRUCTIONS PARTS LIST Harness Kit (sold separately): P/N 08E02-SEC-200
Accessory
Application
HANDS-FREE TELEPHONE INTERFACE
2004 TSX
Publications No.
BII 24809 Issue Date
JULY 2003
Hands-Free Telephone Kit (sold separately): P/N 08E00-ED0-200 Control unit
Telephone harness
2 Rubber spacers
Microphone 10 Wire ties
5 Cushion tapes Owner’s Manual
2 EPT seals
Earphone
Grommet Earphone hanger clip Long wire tie Phone Cable (sold separately): Telephone cable 2 Self-tapping screws, 3 x 8 mm
(The cable type is dependent upon the customer’s cellular phone.)
Modular jack
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
08E02-SEC-2000-92
1 of 15
Illustration of the Hands-Free Telephone Installed in the vehicle
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Stubby Phillips screwdriver Flat-tip screwdriver Isopropyl alcohol Shop towel Tape measure Felt-tip pen Utility knife Scissors Drill 3 mm and 9 mm Drill bits 13/16" (20 mm) Hole saw Center punch Pushpin Diagonal cutters 8 mm Socket Eye protection (face shield, safety goggles, etc.) Hook tool
MICROPHONE
VEHICLE 20-PIN CONNECTOR
AUDIO UNIT With radio tuner CELLULAR PHONE
AMPLIFIER UNIT TELEPHONE ECU HARNESS CONTROL UNIT
Illustration of the Hands-Free Telephone Interface
3207030B
MODULAR JACK VEHICLE 20-PIN CONNECTOR AUDIO UNIT With radio tuner
INSTALLATION
AMPLIFIER UNIT CONNECTOR
AMPLIFIER UNIT CELLULAR PHONE
NOTE: If the hands-free telephone interface is being installed at the same time as the center console CD changer, install the CD changer before doing the hands-free telephone interface installation.
TELEPHONE ECU HARNESS
EARPHONE HANGER CLIP
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
CONTROL UNIT
1.
Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
MICROPHONE
EARPHONE
TELEPHONE CABLE
2 of 15
3207020B
MODULAR JACK
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
3.
Remove the center console panel.
A/T Model:
M/T Model:
•
Loosen the locknut, and remove the shift knob by turning it counterclockwise.
Pull up on the parking brake lever to prevent the vehicle from moving.
•
Move the shift lever into Neutral.
Remove the locknut.
•
Gently pry up on the center console panel to release the eight clips.
•
Unplug the two seat heater connectors (if equipped), and remove the center console panel.
• •
SHIFT KNOB
CLIPS (8)
CENTER CONSOLE PANEL
LOCKNUT
2031021S
•
Gently pry up on the center console panel to release the eight clips.
•
Unplug the two seat heater connectors (if equipped), and remove the center console panel.
CLIPS (8)
2031040S
SEAT HEATER CONNECTOR (if equipped)
CENTER CONSOLE PANEL
4.
Open the pocket lid. Pull the pocket out toward you to release the four clips, unplug the illumination bulb, and remove the pocket. Take care not to damage the illumination bulb.
ILLUMINATION BULB
LID POCKET
SEAT HEATER CONNECTOR (if equipped)
2031030S
2031050S
CLIPS (4)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
3 of 15
5.
Remove the four self-tapping screws.
8.
SELF-TAPPING SCREW (Reuse.)
Remove the passenger’s instrument side trim: •
Open the glove box.
•
Release the one clip on the right side by pushing it from the back of the passenger’s instrument side trim.
•
Wrap the end of the flat-tip screwdriver with a shop towel, then pull the passenger’s instrument side trim out toward you to release the other five clips, and remove the passenger’s instrument side trim.
CLIP
SELF-TAPPING SCREW (Reuse.)
Push this clip from the back of the passenger’s instrument side trim.
COIN POCKET HOLDER
CLIPS (6) SHOP TOWEL
VEHICLE CONNECTOR
2N03011S
6.
Gently pull out the coin pocket holder to release the clip, unplug the vehicle connector, and remove the coin pocket holder.
7.
Remove the rear console.
SCREWDRIVER
•
Open the lid, and remove the rear console mat from inside the rear console.
•
Remove the two screws and the four selftapping screws, and unplug the connector and harness clip (if equipped).
PASSENGER’S INSTRUMENT GLOVE BOX SIDE TRIM
9. SELF-TAPPING SCREWS (4)
2031071S
Using a hook tool, pull out the clip closest to the steering column as shown. HOSE
REAR CONSOLE MAT
VEHICLE CONNECTOR
LID
HOOK TOOL
REAR CONSOLE
Pull out. CLIPS (3) 3123011B
SCREWS (2)
DRIVER’S INSTRUMENT SIDE TRIM
2N01030Y
HARNESS CLIP (if equipped)
4 of 15
CONNECTOR (if equipped)
10. Pull out on the driver’s instrument side trim to release the other two clips, and unplug the vehicle connector and the hose. Remove the side trim.
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
With Navigation System:
11. Unplug the connector, and remove the hazard switch.
HAZARD SWITCH
CONNECTOR
2N27150S
12. Remove the audio-HVAC display module: •
Remove the three self-tapping screws and the two screws.
•
Pull out the audio-HVAC display module to release the six retaining clips and two tabs.
•
Unplug all of the connectors.
•
Unclip the four harness retaining clips.
20-PIN CONNECTOR
Without Navigation System: RETAINING CLIPS (6) AUDIO-HVAC DISPLAY MODULE
TAB
20-PIN CONNECTOR
SELF-TAPPING SCREWS (3)
SCREWS (2)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
3307010Y
BII 24809 (0307)
5 of 15
13. Remove the dashboard lower cover (one selftapping screw and three retaining clips).
Installing the Microphone Cord 15. Lower the steering wheel tilt lever. Remove the upper and lower steering column covers (two selftapping screws and eight clips). Gently push in the six retaining tabs, and carefully separate the two steering column covers.
DASHBOARD LOWER COVER Push.
UPPER STEERING COLUMN COVER
UPPER STEERING COLUMN COVER
LOWER STEERING COLUMN COVER
SELF-TAPPING SCREW 2N01080Y
14. Pull down the three clips in the dashboard under cover, and remove the dashboard under cover by releasing the two tabs. LOWER STEERING COLUMN COVER
CLIP
SCREW
SELF-TAPPING SCREW 2N01090Y
2N19010S
TAB TAB
6 of 15
DASHBOARD UNDER COVER
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
16. Mark the upper steering cover using a pushpin. CENTER OF THE UPPER STEERING COLUMN COVER MARK WITH A PUSHPIN
20. Using isopropyl alcohol, clean the area where the EPT seals will attach. Using scissors, cut one EPT seal as shown. Attach 1/8 of the EPT seal to the hole where the cable will attach. Retain the other half of the EPT seal.
EPT SEAL
Use1/8.
DRILL 1/8 EPT SEAL
DRILL BIT CENTER 2N21020B
17. While wearing eye protection, drill a 9 mm hole through the mark. First drill with a 3 mm bit, then finish with a 9 mm bit. Remove all burrs. 18. Using isopropyl alcohol on a shop towel, clean the bonding surface of the upper steering cover where the microphone will attach.
2N01120Y
21. Using isopropyl alcohol, clean the area where the EPT seals will attach. 22. Attach 1/8 of the EPT seal to the hole from inside of the upper steering column cover where the cable will attach.
ADHESIVE BACKING
MICROPHONE Clean with isopropyl alcohol.
1/8 OF EPT SEAL
UPPER STEERING COLUMN COVER
RUBBER
HALF OF EPT SEAL
DRILL HOLE INSIDE OF THE UPPER STEERING COLUMN COVER CENTER OF THE UPPER STEERING COLUMN COVER
MICROPHONE CABLE
HALF OF EPT SEAL
EPT SEAL
2N01110Y
2N01130Y
19. Remove the adhesive backing from the microphone, and attach it to the surface of the upper steering column cover. Route the microphone cable through the hole.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
23. Using scissors, cut one EPT seal in half. Attach the cable to the inside of the upper steering column cover with the two halves of the EPT seal.
BII 24809 (0307)
7 of 15
24. Position the upper steering column cover above the steering column, and route the microphone cable to the right of the column.
27. Reinstall the lower steering column cover. 28. Make sure the microphone cable doesn’t interfere with or get pinched by the cover and the steering wheel tilt mechanism.
UPPER STEERING COLUMN COVER
2N21030B
LOWER STEERING COLUMN COVER
STEERING COLUMN
25. Route the microphone cable through the dashboard along the vehicle harness. 2N01190Y
MICROPHONE CABLE
VEHICLE HARNESS
SCREW (reused)
SELF-TAPPING SCREW (reused)
29. Route the end of the microphone cable as shown, then secure the cable to the vehicle harness with one wire tie. AUDIO-HVAC DISPLAY MODULE
WIRE TIE
WIRE TIE
VEHICLE HARNESS 2N21040B
26. Secure the microphone cable to the vehicle harness with two wire ties.
VEHICLE HARNESS MICROPHONE CABLE 2N01160Y
8 of 15
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
30. Continue routing the microphone cable as shown. Adjust the length of the microphone cable so that approximately 130 mm of cable is behind the vehicle harness clip. MICROPHONE CABLE
32. Route the white/black wire of the telephone harness along the vehicle harness toward the vehicle 20-pin connector (for the radio tuner). 33. Plug the white/black wire terminal into the vehicle 20-pin connector, and gently pull the wire to make sure is seated into the connector.
VEHICLE HARNESS CLIP (Measure the cord length from the vehicle harness clip.)
TERMINAL LOCK Release and lock.
Firmly push the terminal into the connector until it clicks into position. CONNECTOR LOCK (facing up) VEHICLE 20-PIN CONNECTOR WHITE/ BLACK WIRE
BRACKET (Route the microphone cord outside the bracket.) 130 mm
View from the wire harness
2N21050B
Installing the Telephone Harness
TELEPHONE HARNESS WHITE/BLACK WIRE TERMINAL POSITION
31. Remove the amplifier unit (two nuts), then unplug the vehicle amplifier connectors.
WIRE TIE
VEHICLE AMPLIFIER CONNECTOR
VEHICLE AMPLIFIER CONNECTOR (2)
NUTS (2)
TELEPHONE HARNESS 3207010B
34. Secure the white/black wire of the telephone harness to the vehicle harness with two wire ties in the areas shown.
AMPLIFIER UNIT 3206010B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
9 of 15
35. Connect the vehicle amplifier 20-pin connector disconnected in step 31 to the 20-pin connector of the telephone harness. 36. Plug the telephone harness 20-pin connector and the vehicle amplifier connector into the amplifier unit.
Installing The Control Unit 40. If equipped, move the vehicle harness out of the way. Using a felt-tip pen and a tape measure, measure and mark the floor carpet. Cut the marked lines with a utility knife. Make a slit on each marked line.
VEHICLE AMPLIFIER CONNECTOR
MARK (Make a slit for wire tie installation.)
10 mm
20-PIN CONNECTOR NUTS (2) (reused)
UTILITY KNIFE 10 mm
FLOOR CARPET
20-PIN CONNECTOR
MOVE
3207050B
AMPLIFIER UNIT
60 mm
TELEPHONE HARNESS
VEHICLE HARNESS (if equipped) 2N21090B
37. Reinstall the amplifier unit with the two nuts. 38. Route the remaining telephone harness toward the rear as shown. Make a loop in the microphone cable, and secure the microphone cable and the telephone harness to the vehicle harness with two wire ties in the areas shown.
41. Using diagonal cutters, cut the parking brake switch wire clip, and discard it.
PARKING BRAKE SWITCH WIRE CLIP (Discard.)
39. Secure the telephone harness and the microphone cable with one wire tie near the vehicle harness clips.
WIRE TIE
LONG WIRE TIE
WIRE TIE
VEHICLE HARNESS MICROPHONE CABLE (Make a loop in the microphone cable in here.)
FLOOR CARPET HOLE SLIT
TELEPHONE HARNESS
42. Route the wire tie through the slit in the carpet, and secure the control unit with the wire tie as shown. Route the long wire tie through the carpet hole, and secure the control unit and parking brake switch wire with the long wire tie as shown.
WIRE TIE
WIRE TIE
43. Plug the microphone jack and, the telephone harness connector into the control unit.
VEHICLE HARNESS CLIP
10 of 15
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Modular Jack and Control Unit
46. Measure and mark the rear console as shown.
44. Remove the rear console lid (two screws). TAPE MEASURE (Start measure at this edge.)
SCREW (Reuse.)
REAR CONSOLE LID
REAR CONSOLE
2220062K
MARK
45. Remove the two self-tapping screws, and release the two clips; then remove the rear cover and the bracket.
40 mm
MARK CLIPS (2) 95 mm 25 mm
16 mm
16 mm
2530011K
MARK
REAR COVER SELF-TAPPING SCREW (Reuse.)
2220052K
BRACKET 2709020K
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
11 of 15
47. Mark the panel using a pushpin. While wearing eye protection, drill two 3 mm holes and one 20 mm hole using a 3 mm drill bit and 20 mm hole saw. Remove all burrs from the edges of the holes.
MARK (pushpin hole)
51. Reinstall the bracket with the two screws.
SCREWS (reused)
MARK (pushpin hole)
3 mm DRILL BIT
PUSHPINS MARK 20 mm HOLE SAW (pushpin hole) 2530020K
BRACKET
48. Using isopropyl alcohol on a shop towel, clean the bonding surface inside the console box. Route the modular jack cable through the 20 mm hole, and install the grommet on the cable.
2304062K
52. Using scissors, cut one cushion tape in half. Using isopropyl alcohol, clean the area where the cushion tape will attach. Attach the modular cable to the panel and to the bracket with the two halves of the cushion tape in the areas shown. Wrap the cable with the remaining half of the EPT seal (cut in step 20) in the area shown.
GROMMET Clean the panel with isopropyl alcohol. ADHESIVE BACKING
CUSHION TAPE
MODULAR JACK CONSOLE BOX
PANEL HALF OF CUSHION TAPE
BRACKET 20 mm HOLE
3 x 8 mm SELFTAPPING SCREWS (Do not overtighten.)
MODULAR JACK EARPHONE CABLE JACK
Clean the panel and bracket with isopropyl alcohol.
2530030K
REMAINING HALF OF EPT SEAL
49. Remove the adhesive backing from the modular jack, and attach the modular jack, aligning the 3 mm holes with the holes in the modular tabs. Install and tighten the two 3 x 8 mm self-tapping screws. Do not overtighten the two self-tapping screws.
2N28010B
50. Plug the earphone jack into the modular jack. Install the grommet into the hole.
12 of 15
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
53. Reinstall the rear cover with the two self-tapping screws removed in step 45.
Installing the Earphone
SELF-TAPPING SCREW (reused)
56. Using isopropyl alcohol on a shop towel, clean the bonding surface of the rear console storage area. Remove the adhesive backing from the earphone hanger clip, and attach the earphone hanger clip to the rear console storage area.
ADHESIVE BACKING FORWARD CENTER 30 mm
2305042K
REAR COVER
54. Place the rear console above the control unit. Plug the modular cable connector into the control unit. EARPHONE HANGER CLIP
Clean the area with isopropyl alcohol.
2530040K
BRACKET
57. Place the earphone on the earphone hanger clip, and plug the earphone cable jack into the modular jack. MODULAR JACK
CONTROL UNIT CUSHION TAPE
2N28021B
EARPHONE EARPHONE HANGER CLIP
Clean the bracket MODULAR with isopropyl CABLE CONNECTOR alcohol.
55. Using isopropyl alcohol on a shop towel, clean the bonding surfaces on the bracket. Attach one cushion tape to the edge of the bracket as shown. EARPHONE CABLE JACK 2530050K
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
13 of 15
58. Bundle up the excess modular cable, and place it under the carpet.
60. Lay the telephone cable on the tray as shown, and connect the telephone cable connector to the cellular phone. CELLULAR PHONE (Supplied by your customer.)
TRAY
TELEPHONE CABLE CONNECTOR MODULAR CABLE (Place it under the floor carpet.) 2N28030B
2606010K
61. Reconnect the telephone harness connector, the vehicle connectors, and the antenna lead. Reinstall the audio-HVAC-display-module.
59. Plug the telephone cable connector into the telephone modular connector. Hook the telephone cable to the tray hooks as shown, and lower the tray.
With Navigation System:
TELEPHONE CABLE TRAY
HOOK 20-PIN CONNECTOR TELEPHONE CABLE CONNECTOR
Without Navigation System:
MODULAR CONNECTOR 2605150K
20-PIN CONNECTOR
14 of 15
BII 24809 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
62. Check that all wire harnesses are routed properly and all connectors are plugged in. 63. Reinstall all removed parts. 64. Reconnect the negative cable to the battery. 65. Test the driver's window AUTO function. 56. Enter the anti-theft codes for the radio and the navigation system (if equipped), then reset the customer’s radio station presets. 57. Set the clock.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 24809 (0307)
15 of 15
