050-367 - Glenair

Transcript

050-367 PRODUCT BRIEF SIZE 8 ELECTRO-OPTICAL CONTACT TRANSMITTER OR RECEIVER SMPTE 3G-SDI AND HD-SDI FRONT INSERT – FRONT RELEASE REV B C D E DESCRIPTION Per DCN60097 Per DCN62204; Edit PRBS Specification to 27-1 Per DCN63108; Update Min. Extinction Ratio to 5dB per SMPTE Standard Per DCN63598; Add part number options to distinguish between 3G-SDI and HD-SDI BF15U2-3711 DATE 05/09/2016 10/20/2016 12/13/2016 01/24/2017 APPROVED SZ/NH/RS SZ/GC RAS/GC RAS/GC/SZ THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC. 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Size 8 Cavity Opto-Electronic Contacts, 3G-SDI & HD-SDI, MMF, 3.3V Glenair 050-367, Size 8 Cavity Opto-electronic contacts transmit and receive differential CML electrical signals over Multimode fiber optic cable that has been optimized for SMPTE 3G-SDI and HD-SDI signals. Transmitter size 8 contacts consist of a laser driver with a temperature compensation circuit to maintain optical power over the entire operating temperature range, and a 850nm VCSEL laser. The transmitter has a Tx Disable pin to turn off transmitter output and a Tx Fault pin to signal a fault condition. This laser driver circuit regulates the optical power at a constant level provided the data pattern is relatively DC balanced and can support SMPTE EG 34:2004 Pathological conditions CASE 1, CASE2, and CASE 3 for HD-SDI and 3G-SDI Receiver size 8 contacts consist of an 850nm PIN Photo Detector, a Transimpedance Amplifier with automatic gain control circuit and a Limiting Amplifier. Differential output data signals are CML compatible. Receiver includes a CMOS compatible Loss of Signal Indicator to prevent invalid data. These receiver designs support SMPTE 424 (3G-SDI) and SMPTE 292 (HD-SDI), with special considerations to comply with the SMPTE Pathological test cases as described in SMPTE EG 34:2004. The receiver support BER <10-12 with Pathological test conditions CASE1, CASE3 and CASE3. These contacts are designed to operate in for harsh temperature and vibration environments found in Military, Aerospace, Railway, Oil and Gas, and Industrial applications. They can be incorporated into 38999 and other harsh environment connectors. KEY FEATURES/BENEFITS          SMPTE EG 34:2004 Compliant to Pathological Conditions CASE 1, CASE 2 and CASE 3. SMPTE ST 297:2006 (3G-SDI & HD-SDI) SMPTE 424 Compliant (3G-SDI) SMPTE 292 Compliant (HD-SDI) SFP Compatible Electrical Input signal levels 850nm VCSEL support 3G-SDI & HD-SDI Industry standard CML input and outputs that make for simple integration on customer host PCB Front-release, front-insert, front-removable Fits size 8 quadrax cavity for ARINC 600 HOW TO ORDER Table 1 GLENAIR, INC. www.glenair.com Harsh Environment such as: Airborne, Tactical, Railway, Industrial, Oil and Gas and Shipboard applications o SMPTE 3G & HD-SDI Video Applications Description HD-SDI Transmitter HD-SDI Receiver 3G-SDI Transmitter 3G-SDI Receiver REV: E ∙  Part Number Options Part Number 050-367-1-T 050-367-1-R 050-367-T 050-367-R ©2017 Glenair, Inc.  Solutions available in 38999 style connectors  -40°C to +85°C Operating Case Temperature  Evaluation fixtures available APPLICATIONS 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 2 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Ratings and Specifications – HD-SDI VERSION TABLE 2 ABSOLUTE M AXIMUM RATINGS Parameter Symbol Min Storage Temperature Ts Supply Voltage Typ Max Units -55 +100 °C Vcc -0.4 3.8 V Symbol Min Max Units Operating Temperature, Case Top -40 +85 °C Supply Voltage Vcc 3.135 Supply Current Icc Notes VccT may not differ by more than 0.5V TABLE 3 OPERATING CONDITIONS Parameter Power Supply Noise (Peak-Peak) Typ 3.3 3.465 V 180 200 mA 100 mV Vcc_ripple Notes Typical @ +85°C TABLE 4 ELECTRO-OPTICAL CHARACTERISTICS – TRANSMITTER Parameter Optical Output Power Extinction Ratio Symbol Min Typ Max Units Notes POUT -8 -5 -3 dBm 850nm VCSEL, 1.5Gbps 860 nm Er 5 10 Optical Wavelength λOUT 830 850 Spectral Width, rms Δλ 0.85 nm Relative Intensity Noise RIN -117 dB/Hz Timing Jitter TJ 1 UI SMPTE 292, 1.5 Gbps, Color bar UI SMPTE 292, 1.5 Gbps, Color bar Alignment Jitter AJ Transmitter Differential Input Impedance Zin Differential Input Voltage Vin_d dB 0.2 100 250 2200 @1.5Gbps Ohms AC coupled Internally mVp-p CML, 100 ohm TABLE 5 ELECTRO-OPTICAL CHARACTERISTICS - RECEIVER Parameter Symbol -12 7 Min Sensitivity, BER 10 , PRBS 2 -1, Er 10 dB PIN Overload, BER 10-12, PRBS 27-1 PIN -1 Optical Wavelength λIN 830 Receiver Differential Output Impedance Zout Differential Output Voltage Swing Vout_d LOS Assert Level LOSHYS ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: E ∙ 1211 AIR WAY Max Units Notes -22 -20 dBm PIN PD @ 1.485 Gbps dBm @1.485 Gbps 860 100 600 LOS LOS Hysteresis Typ Ohms AC coupled internally 1200 mVp-p CML, 100 ohm -21 dBm @1.485 Gbps dB @1.485 Gbps -23 1.25 nm 2.3 US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 3 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Ratings and Specifications – HD-SDI VERSION (continued) TABLE 6 COMPLIANCE SPECIFICATIONS CHARACTERISTIC Standard ESD MIL-STD-883 Eye Safety CDRH and IEC-825 ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com Condition REV: E ∙ 1211 AIR WAY Notes 1000V HBM Class 1 Laser Product US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 4 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Ratings and Specifications – 3G-SDI VERSION TABLE 7 ABSOLUTE M AXIMUM RATINGS Parameter Symbol Min Storage Temperature Ts Supply Voltage Typ Max Units -55 +100 °C Vcc -0.4 3.8 V Symbol Min Max Units Operating Temperature, Case Top -40 +85 °C Supply Voltage Vcc 3.135 Supply Current Icc Notes VccT may not differ by more than 0.5V TABLE 8 OPERATING CONDITIONS Parameter Power Supply Noise (Peak-Peak) Typ 3.3 3.465 V 180 200 mA 100 mV Vcc_ripple Notes Typical @ +85°C TABLE 9 ELECTRO-OPTICAL CHARACTERISTICS – TRANSMITTER Parameter Optical Output Power Extinction Ratio Symbol Min Typ Max Units Notes POUT -8 -5 -3 dBm 850nm VCSEL, 2.97Gbps 860 nm Er 5 10 Optical Wavelength λOUT 830 850 Spectral Width, rms Δλ 0.85 nm Relative Intensity Noise RIN -117 dB/Hz Timing Jitter TJ 2 UI SMPTE 424, 2.97Gbps, Color bar UI SMPTE 424, 2.97Gbps, Color bar Alignment Jitter AJ Transmitter Differential Input Impedance Zin Differential Input Voltage Vin_d dB 0.2 100 250 2200 @2.97Gbps Ohms AC coupled Internally mVp-p CML, 100 ohm TABLE 10 ELECTRO-OPTICAL CHARACTERISTICS - RECEIVER Parameter Symbol -12 7 Min Sensitivity, BER 10 , PRBS 2 -1, Er 10 dB PIN Overload, BER 10-12, PRBS 27-1 PIN -1 Optical Wavelength λIN 830 Receiver Differential Output Impedance Zout Differential Output Voltage Swing Vout_d LOS Assert Level LOSHYS ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: E ∙ 1211 AIR WAY Max Units Notes -19 -17 dBm PIN PD @ 2.970 Gbps dBm @ 2.970 Gbps 860 100 600 LOS LOS Hysteresis Typ Ohms AC coupled internally 1200 mVp-p CML, 100 ohm -21 dBm @ 2.970 Gbps dB @ 2.970 Gbps -23 1.25 nm 2.3 US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 5 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Ratings and Specifications – 3G-SDI (continued) TABLE 11 COMPLIANCE SPECIFICATIONS CHARACTERISTIC Standard ESD MIL-STD-883 Eye Safety CDRH and IEC-825 ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com Condition REV: E ∙ 1211 AIR WAY Notes 1000V HBM Class 1 Laser Product US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 6 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V FUNCTIONAL DESCRIPTION Figure 2 Functional Block Diagram FUNCTIONAL I/O The Size 8 module is compatible with industry standard differential signals such as CML within the scope of the SFP MSA. The module is DC-coupled and internally terminated. Figure 3 illustrates a recommended interface circuit to size 8 transmitter/receiver and the supporting Physical Layer integrated circuits. The transmitter interfaces with the host circuit board through six I/O pins identified by function in Table 7. The transmitter high speed transmit and interfaces require SFP MSA compliant signal lines on the host board. The TX_DISABLE, TX_FAULT require TTL lines on the host board (per SFF-8074i) if used. If an application chooses not to take advantage of the functionality of these pins TX_Disable need to be tied to GND, TX_Fault do not need to be connected. The receiver interfaces with the host circuit board through six I/O pins identified by function in Table 8. The receiver high speed receive and interfaces require SFP MSA compliant signal lines on the host board. ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: E ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 7 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V FIGURE 3 RECOMMENDED BOARD HOST BOARD SCHEMATIC TRANSMITTER RECEIVER ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: E ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 8 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-367 PRODUCT BRIEF Size 8 OE Contact, Front Insert/Front Release 3G-SDI and HD-SDI, MMF, 3.3V Required Host Board Components A power supply noise rejection filter as describe in SFP MSA is required on the host PCB to meet data sheet performance. This filter incorporates an inductor which should be rated 400 mADC and 1 Ω series resistance or better. It should not be replaced with a ferrite. The required filter is illustrated in Figure 4. Also, the host PCB for the transmitter requires 4.7 K to 10 KΩ pull-up resistors for TX_FAULT. The host PCB for the receiver requires 4.7 K to 10 KΩ pull-up resistors for RX_LOS. Fiber Compatibility The SMPTE link is capable of error free signal detection for 2 to 500 meters with OM3 50/125 μm fiber, 2 to 170 meters with OM2 50/125 μm fiber, and at 2 to 60 meters with OM1 62.5/ 125 μm fiber, for 3G-SDI data rate Electrostatic Discharge (ESD) The size 8 contacts are compatible with ESD levels found in typical manufacturing and operating environments as described JEDEC EIA JESD22-A114-A, Class 1C (<2000Volts) HBM. Glenair recommends that devices are handled with ESD precautions to limit exposure to below 500V HBM. There are two design cases in which immunity to ESD damage is important. The first case is during handling of the components prior to insertion to the host board. It is important to use standard industry ESD handling precautions such as using grounded wrist straps, work benches, and floor mats in ESD controlled areas. The ESD sensitivity of the Glenair device is compatible with typical industry production environments. The second case to consider is static discharges to the exterior of the host equipment after installation, in which case the electro-optical component may be subject to system-level ESD requirements. Application Support To assist in the dual-transmitter design and evaluation process, Glenair offers the following aids: • Evaluation board & Product Manual • 3D Step file to support modeling of mechanical fit and routing ©2017 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: E ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 9 of 9 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected]