08 Inglese

Transcript

SW41SK-SW81SK VIDEO SWITCHING LOW COST SEQUENTIAL SWITCHERS • 4/8 video inputs - 1 video output • Adjustable switching time • Skip function • New design SW41SK SW41SK and SW81SK units are sequential switchers constructed in a sturdy aluminium container, equipped respectively with 4 and 8 video inputs and 1 video output. The selection of the video input can be performed manually or in automatic switching; in this latter case, the switching is performed on the number of the consecutive video inputs set by the user (skip function). In automatic functioning, the switching time can be adjusted by means of a potentiometer (from 0.5 to 30 seconds). The active video input and the automatic functioning are signalled by red LEDS built-in in the push-buttons. Dimensions: 210 x 185 x 60 mm Weight: 1,55 Kg (SW41SK) 1,6 Kg (SW81SK) SW81SK 8 CODE 03/00 DESCRIPTION SW41SK Sequential switcher 4 inputs and 1 output SW81SK Sequential switcher 8 inputs and 1 output 8•1 SW41SK-SW81SK TECHNICAL DOCUMENTATION 1 output 1/4 or 1/8 inputs SW41SK SW81SK Low cost sequential switchers - inputs: 4/8 output: 1 video signal: 1Vpp/75½ band width: 6MHz cross-talk: -50dB power supply: 230V~ 50/60Hz 5W AUTO key for automatic switching direct selection keys 8 8•2 SW42K-SW82K VIDEO SWITCHING DESKTOP MICROPROCESSOR CONTROLLED SEQUENTIAL SWITCHERS SW42K • Microprocessor controlled unit • 4/8 video inputs - 2 video outputs • 4/8 alarm inputs • VCR trigger input • On screen menu programming SW42K and SW82K units are sequential switchers controlled by a microprocessor constructed in a sturdy aluminium container, equipped respectively with 4 and 8 video inputs and 2 independent video outputs: AUTO and MAN. The AUTO output follows exclusively the programmed sequence, whereas the MAN output allows for manual selection of the video inputs. The switching time can be selected separately for each video input between 0 and 240 seconds. They control 4 or 8 alarm inputs, which can be separately selected as normally open or normally closed. In case of alarm, both AUTO and MAN outputs switch the cameras corresponding to the alarm inputs with an adjustable dwell time. The alarm reset is performed through keyboard, time-out or exter- SW82K nal contact. The DB15 connector, positioned on the back side of the unit, allows for the connection to the contacts of a relay activated in case of alarm. Furthermore, it is possible to control the video switching of the inputs with a VCR trigger. The MAN output is equipped with an alphanumeric generator which numbers the video inputs. 8 The programming of all functions is performed through On Screen Menu. Dimensions: 260 x 185 x 60 mm Weight: 1,8 Kg (SW42K) 1,85 Kg (SW82K) CODE 03/00 DESCRIPTION SW42K Sequential switcher 4 inputs and 2 outputs SW82K Sequential switcher 8 inputs and 2 outputs 8•3 SW82K-SW42K TECHNICAL DOCUMENTATION 4 or 8 direct selection keys alarm and trigger SW42K SW82K Microprocessor controlled sequential switchers 8 8•4 - inputs: 4/8 output: 2 video signal: 1Vpp/75½ band width: 5MHz cross-talk: -50dB relay contact: 125V~ 0,3A - power supply: 230V~ 50/60Hz 10W connector 4/8 video inputs 2 outputs automatic and programming key SW42LOC-SW82LOC SW42LOC VIDEO SWITCHING VIDEO SWITCHER CONTROLLED BY MICROPROCESSOR SW82LOC • Microprocessor controlled unit • 4/8 video inputs - 2 video outputs • 4/8 alarm inputs • VCR trigger input • On screen menu programming • Optional Rack 19” version SW42LOC and SW82LOC units are sequential switchers controlled by a microprocessor, equipped respectively with 4 and 8 video inputs and 2 independent video outputs: AUTO and MAN. The AUTO output follows exclusively the programmed sequence, whereas the MAN output allows for manual selection of the video inputs. The switching time can be selected separately for each video input between 0 and 240 seconds. They control 4 or 8 alarm inputs, which can be separately selected as normally open or normally closed. In case of alarm, both AUTO and MAN outputs switch the cameras corresponding to the alarm inputs with an adjustable dwell time. The alarm reset is performed through keyboard, time-out or external contact. The DB15 connector, positioned on the back side of the unit, allows for the connection to the contacts of a relay activated in case of alarm. Furthermore, it is possible to control the video switching of the alarm inputs with a VCR trigger. The MAN output is equipped with an alphanumeric generator 8 which numbers the video inputs. The programming of all functions is performed through On Screen Menu. Dimensions: 223 x 203 x 45 mm Weight: 1,8 Kg (SW42LOC) 1,85 Kg (SW82LOC) CODE 03/00 DESCRIPTION SW42LOC Sequential switcher 4 inputs and 2 outputs SW82LOC Sequential switcher 8 inputs and 2 outputs RM1 RACK adaptor for 1 sequential switcher RM2 RACK adaptor for 2 sequential switchers 8•5 SW42LOC-SW82LOC TECHNICAL DOCUMENTATION 4-8 video inputs SW42LOC SW82LOC Microprocessor controlled sequential switchers - input: 4/8 output: 2 video signal: 1Vpp/75½ band width: 5MHz cross-talk: -50dB relay contact: 125V~ 0,3A - power supply: 230V~ 50/60Hz 10W 2 video outputs alarm, reset, trigger VCR power switch direct selection keys 8 8•6 auto and programming key SW42RC-SW82RC VIDEO SWITCHING MICROPROCESSOR CONTROLLED SEQUENTIAL SW42REM SW82REM SWITCHER WITH REMOTE CONTROL SWC8 SWC4 • Microprocessor controlled unit • Remote control up to 500 m • 4/8 video inputs - 2 video outputs • 4/8 alarm inputs • VCR trigger input • On screen menu programming SW42REM and SW82REM units are sequential switchers controlled by a microprocessor, equipped respectively with 4 and 8 video inputs and 2 outputs. These switchers are characterized by the option of combining them with a control keyboard, SWC4 and SWC8, which can control them from distances up to 500m by means of a twisted pair, SW42REM with access to all functions. Dimensions: 223 x 203 x 45 mm The two video outputs are respectively automatic and manual. The Weight: 1,8 Kg AUTO output follows exclusively the programmed sequence, whereas the MAN output allows for manual selection of the video SW82REM inputs. The switching time can be selected separately for each Dimensions: 223 x 203 x 45 mm video input between 0 and 240 seconds. They control 4 or 8 Weight: 1,85 Kg alarm inputs, which can be separately selected as normally open or normally closed; in case of alarm, both AUTO and MAN out- SWC4 puts switch the cameras corresponding to the alarm inputs with an Dimensions: 185 x 135 x 60 mm adjustable dwell time; furthermore, it is possible to control the Weight: 1,30 Kg video switching of the alarm inputs with a VCR trigger. The alarm reset is performed through keyboard, time-out or exter- SWC8 nal contact. The DB15 connector, positioned on the back side of Dimensions: 185 x 135 x 60 mm the unit, allows for the connection to the contacts of a relay activa- Weight: 1,30 Kg 8 ted in case of alarm. The MAN output is equipped with an alphanumeric generator which numbers the video inputs. The programming of CODE DESCRIPTION all functions is performed through On Screen Menu. The SW82REM unit allows the cascade connection of two switchers controlled by the same control keyboard (in this particular case DCMT8), thus creating a small CCTV system with 16 video inputs and 4 outputs. 03/00 SW42REM Sequential switcher 4 inputs and 2 outputs SW82REM Sequential switcher 8 inputs and 2 outputs SWC4 Control keypad for SW42REM SWC8 Control keypad for SW82REM SW42RC System made up of SW42REM + SWC4 SW82RC System made up of SW82REM + SWC8 8•7 SW42RC-SW82RC TECHNICAL DOCUMENTATION RJ jack for SWC4/SWC8 or DCMT8 control keypad SW42RC SW82RC Microprocessor controlled sequential switchers - inputs: 4/8 outputs: 2 video signal: 1Vpp/75½ band width: 5MHz cross-talk: -50dB relay contact: 125V~ 0,3A - power supply: 230V~ 50/60Hz 10W 4/8 alarm inputs trigger VCR relè alarm 4/8 direct 2 outputs fuse selection keys 4/8 inputs auto scan and programming key DCMT8 SW82REM SW82REM 8 8 inputs 8 inputs 2 outputs 8•8 8 alarm inputs 2 outputs 8 alarm inputs DCMT8 TELEMETRY CONTROLLER TELEMETRY AND VIDEO SWITCHING CONTROLLER • Microprocessor controlled unit • RS232 and Current Loop transmission • Video switching and telemetry • Direct control of 16 video inputs • Simultaneous control of 2 switchers The DCMT8 unit is a control keyboard controlled by a microprocessor for video switching and telemetry operations. The video switching is performed through a SW42REM or SW82REM unit, respectively for 4 or 8 video inputs, or through 2 SW82REM units for 16 video inputs. The control of peripheral stations takes place by means of DTMRX, DTRX and MICRODEC control receivers. DCMT8 allows for the control of 16 video inputs, including the programming of the display cycles, and 16 digital receivers for the control of pan & tilt motors and motor-driven zoom lenses. The solid construction, refined design and easiness of use of this SW82REM control unit make it a very practical and functional object. Dimensions: 185 x 150 x 60 mm Weight: 1,5 Kg 8 DTRX DTMRX MICRODEC CODE DCMT8 03/00 DESCRIPTION Desktop telemetry controller 8•9 DCMT8 TECHNICAL DOCUMENTATION Pan & Tilt control Manual - max. distance: 500m from the switcher, 1500m from the receiver (Current Loop), 15m from the receiver (RS232) - video switching - telemetry control - zoom lens control - up to 16 video and tele metry channels - power supply: 230V~ 50/60Hz 4W DCMT8 Control keyboard numeric keypad for or Autopan direct selection and programming keys Zoom lens control functions up to 16 receivers DTMRX PTH900 SW82REM lenses 8 inputs 2 outputs 8 alarm inputs DTMRX PTH300 SW82REM lenses 8 8 inputs 2 outputs 8 alarm inputs DCMT8 8 • 10 SW164OSM VIDEO SWITCHING MATRIX PROGRAMMABLE VIDEO SWITCHING MATRIX • Programmable video matrix • 16 video inputs and 4 video outputs • 16 alarm contacts • Remote control up to 4 operators • Rack 19” 2U • On screen menu programming The SW164OSM video matrix is the heart of a digital video switching system, capable of commuting 16 video inputs on 4 independent outputs. The matrix can be completely controlled for all its functions by four remote operators, by means of DCS2 and KEYPLUS control keyboards. The different control operations are made easier by the LCD display fitted to both keyboard versions, whereas the matrix programming is made through on screen menu. Three different password levels in the keyboard ensure the protection from improper use of the matrix. It is possible to generate a text for each video input up to 24 characters; by means of the optional ID07 board, one of which is already built in on output n. 1 of the matrix, it is possible to display this text and other information (date and hour) on the outputs. For each output channel, it is possible to set two different switching programs controlled by an internal timer; a battery controlled memory will see to keep information unchanged even in case of power loss. A DB25 connector placed on the back of the unit allows 16 alarm contacts to be connected with the corresponding video inputs: in case of alarm, the video outputs switch the cameras correspon- 8 ding to the alarm inputs and a sounder along with a relay are activated, allowing other peripheral units to be activated. It is also possible to define alarm groups in order to connect more cameras to the same alarm. The reset of an alarm situation is performed through keyboard, external contact or time-out. Dimensions: rack 19” 2U Weight: 3,7 Kg CODE SW164OSM 03/00 DESCRIPTION Video matrix 16 inputs and 4 outputs 8 • 11 SW164OSM SW164 OSM Video matrix - TECHNICAL DOCUMENTATION inputs: 16 outputs: 4 operators: 4 alarm inputs: 16 video signal: 1Vpp/75½ band width: 5 MHz cross-talk: -50dB relay contact:125V~ 0,3A power supply: 230V~ 50/60Hz 15W 16 alarm inputs, external reset, trigger 4 RJ jacks for control 4 video outputs keyboards DCS2 DCS2 from 1 to 4 outputs DCS2 from 1 to 16 inputs KEYPLUS 8 16 alarm inputs SW164OSM 8 • 12 16 video inputs SW328 VIDEO SWITCHING MATRIX PROGRAMMABLE VIDEO SWITCHING MATRIX • 32 video inputs and 8 video outputs • 64 sequences (with 32 steps each) • 32 alarm inputs • Windows 95 / NT PC configuration • Videoloss detector The SW328 video matrix is a global solution concerning collection and management of images. The matrix is capable of switching 32 video inputs on 8 indipendent outputs. The system offers the possibility to activate 64 different syncronized sequences among several monitors, with day, night and holiday cycles. The matrix provides 32 alarm inputs, 8 relays controlled by events or alarm contacts (alarm groups), alarm reset through keyboard, external contact or automatic timed reset, user friendly configuration through Windows 95 / NT PC. This product is noteworthy because of the possibility to record the events on a printer, to point out the lack of video signals, and thanks to a competitive price. A keyboard, equipped by a joystick, controlled by a microprocessor, allows to see directly cameras on which act and control the SW328 with DCS3 telemetry and auxiliary functions. 8 Dimensions: rack 19” 5HE Weight: 6,8 Kg CODE SW328 03/00 DESCRIPTION Video matrix 32 inputs and 8 outputs 8 • 13 SW328 TECHNICAL DOCUMENTATION 32 video inputs SW328 Video matrix - inputs: 32 outputs: 8 users: 8 alarm inputs: 32 video signal: 1Vpp/75½ relay contact: 30V 0,5A power supply: 230V~ 50/60Hz 50W 8 video outputs VCR trigger input fuse power supply external reset PC/Printer/VCR control alarm inputs/ relay outputs 4 RJ jacks for control keyboards DCS3 DCS3 from 1 to 32 inputs from 1 to 8 outputs 32 alarm inputs 8 SW328 8 • 14 SWC16 CONTROL KEYBOARD DIGITAL CONTROL FOR SW164OSM MATRIX • Microprocessor controlled unit • RS232 transmission and Current Loop The SW16 keyboard is a professional product that allows the control of video switching of the SW1640SM matrix. It allows the communication in RS232 or in Current Loop at variable baud rates (1200/9600 baud). This keyboard allows the commutation of 16 video inputs with 1 output, defined in the configuration phase, and starting of the automatic cycle pre-set in the matrix. Two keys can be used thus: one to change the video cameras between 1 and 8 or between 9 and 16, the other one to activate the automatic sequence. Being extremely easy to use, in fact the functions are called up by a single key, make this product very useful to install where the operator does not need to alter the programming and can use the basic functions of the video commutation. The feed is through a supplied external feeder. Sizes: 133x 55 x 185 mm Weight: 1,3 Kg 8 SW164OSM CODE SWC16 03/00 DESCRIPTION Matrix control 8 • 15 SWC16 TECHNICAL DOCUMENTATION numerical keypad shift key - max. distance: SWC16 1500 m (Current Loop) 15 m (RS232) - video switching Matrix control - up to 16 video channels - power supply: 230V~ 50/60HZ 4W automatic cycling key KEYPLUS SWC16 from 1 to 4 outputs SWC16 from 1 to 16 inputs 8 SWC16 16 alarm inputs SW164OSM 8 • 16 DCS2-KEYPLUS CONTROL KEYBOARDS DIGITAL CONTROLLERS FOR SW164OSM MATRIX AND TELEMETRY • Microprocessor controlled • LCD Display • RS232 and Current Loop transmission DCS2 DCS2 and KEYPLUS keyboards represent the highest point which can be reached as regards performances: from the control of telemetry functions and zoom lenses, to the control of the auxiliary contacts and the most advanced preset functions. These control keyboards controlled by a microprocessor allow interface with the SW164OSM matrix. An LCD display assists the operator in all system control functions. The units allow for the full control of all the functions of the SW164OSM matrix, including the programming of the switching cycles and texts. The serial line of digital controls can be selected between RS232 and Current Loop, through software configuration. The DCS2 unit can control up to 99 telemetry units and preset and patrol functions, combined with the use of the DTRX+DTRP receiver. DCS2 Dimensions: 185 x 300 x 60 mm Weight: 2,2 Kg KEYPLUS Dimensions: 185 x 185 x 60 mm Weight: 1,7 Kg CODE 03/00 8 KEYPLUS DESCRIPTION DCS2 Control keyboard for matrix and telemetry functions KEYPLUS Control keyboard for matrix 8 • 17 TECHNICAL DOCUMENTATION DCS2-KEYPLUS auxiliary functions pan & tilt control - max. distance: LCD display 1500m (Current Loop) DCS2 KEYPLUS - video switching KEYPLUS - telemetry control (DCS2) - zoom lens control (DCS2) Control keyboards LCD display DCS2 15m (RS232) zoom lens control - up to 99 telemetry receivers (DCS2) numeric - power supply: keypad programming keys 230V~ 50/60HZ 4W programming keys numeric keypad DTRX MICRODEC PTH900 DTMRX DCMX SW164OSM 8 KEYPLUS DCS2 8 • 18 DCS2 KEYPLUS DCS3 CONTROL TASTIERE KEYBOARDS DI CONTROLLO DIGITAL CONTROLLER FOR TELEMETRY AND SW328 MATRIX • Microprocessor controlled unit • LCD Display • RS485 serial communication • Ergonomic design • Telemetry controlled by joystick DCS3 represents the highest point which can be reached as regard performances and ergonomic design. These control keyboards controlled by a microprocessor allow interface with SW328 video matrix. An LCD display assists the operator in all system control functions. The DCS3 unit can control up to 99 telemetry units, preset and patrol functions, in addition to DTRX+DTRP or DTRXDC telemetry receiver. The joystick, controlling pan & tilt functions, allows easiness of use and drive variable speed Pan & Tilt heads and speed dome cameras. It is compatible with JVC TK-C675, Panasonic VWCSR650, Computar SMD20, Er nitec ICU, Star Micr onics MD2000. Dimensions: 185 x 292 x 75 mm Weight: 1,2 Kg DCS3 with SW328 8 CODE DCS3 03/00 DESCRIPTION Control keyboard for matrix and telemetry functions 8 •19 DCS3 TECHNICAL DOCUMENTATION LCD display pan&tilt control auxiliary functions - max. distance: 1200m (RS485) DCS3 Control keyboard - video switching - telemetry control up to 99 units - up to 99 video channels - power supply: 230V~ 50/60HZ 4W numeric keypad DBH24 DTRXDC programming keys zoom lens control PTH355P SW328 8 DCS3 8 • 20 DCS3 MICRODEC MINI TELEMETRY RECEIVER TELEMETRY DATA MINI RECEIVER 8 FUNCTIONS • Small size • Microprocessor controlled • Current Loop communication, remote controllable up to 1500 m (MICRODEC) • RS485 communication, remote controllable up to 1200m (MICRODEC485) MICRODEC and MICRODEC485 are mini digital control receivers managed by a microprocessor for the remote control of a pan and tilt head and motor-driven lenses. Designed for insertion inside housings or pan and tilt heads, they ensure easier installation by reducing the number of connections and equipment (e.g. external boxes). All functions are ennsured by the DCS2 and DCMT8 control units for MICRODEC and by the DCS3 one for the MICRODEC485. The connection to the control unit can be carried out in a Current Loop for MICRODEC (connection distance up to 1500m by twisted pair cable) and in a RS485 for MICRODEC485 (connection distance up to 1200m by twisted pair cable). Up to 32 receivers can be addressed. DCMT8 The feed tension is 24 V~ which must correspond to that of the pan and tilt head. The MICRODEC and MICRODEC485 can control Pan and Tilt _ heads and 12 V… lenses with polarity inversion (zoom and 8 focus); they can be inserted in HEB, HEC and HEG housings. Dimensions: 100 x 60 mm Weight: 120 g DCS2 CODE DESCRIPTION MICRODEC Telemetry receiver - Current Loop - 24 V~ MICRODEC485 Telemetry receiver - RS485 - 24 V~ DCS3 03/00 8 • 21 MICRODEC TECHNICAL DOCUMENTATION - baudrate: 1200/9600 - maximum distance: address selection dip-switch 1500m Current Loop MICRODEC 1200m RS485 reset button - Pan & Tilt - zoom and focus Telemetry microreceiver 8 functions - addressable up to 32 units - control led - Pan & Tilt: 24V~ _ - lenses: 12V… polarity inversion - power supply: 24V~ terminal block 50/60HZ (see specification of the P&T) 1W PTH300 MICRODEC485 lenses 8 DCS3 8 • 22 DTMRX TELEMETRY DATA RECEIVER TELEMETRY RECEIVER 12 FUNCTIONS • Microprocessor controlled unit • 12 functions • RS232, Current Loop or RS485 • Remote controllable up to 1500m • Weatherproof standard IP56 The DTMRX is a digital receiver, controlled by a microprocessor, for remote control of a pan & tilt motor and a motor-driven zoom lens. The DCS2 and DCMT8 control units ensure complete control of all the DTMRX functions. It is interfaced also to PC through RS232. Connection to the control unit can be carried out in RS232, in RS485 or in Current Loop (in this case, the connection distance can reach 1500 m). A IP56 weatherproof box ensures protection against all weather conditions. It is available in 24 V~ or 230 V~ versions for pan & tilt motors, and allows feeding common ground or polarity inversion zoom lenses. A relay auxiliary function is available for controlling, for instance, the switching on and off of a IR illuminator, through a power contact. Four PG11 cable glands make connections easier. DCMT8 Dimensions: 195 x 150 x 70 mm 8 Weight: 0,9 Kg CODE DCS2 03/00 DESCRIPTION DTMRX Data receiver - power supply 230 V~ DTMRX24 Data receiver - power supply 24 V~ 8 • 23 DTMRX TECHNICAL DOCUMENTATION - speed: 1200/9600 baud - max length: 15 m (RS232), 1200m (RS485) or 1500m (Current Loop) fuse - Pan & Tilt, Auto pan DTMRX - lens: zoom, focus e iris - addressable up to 99 units - control led Telemetry receiver 12 functions - auxiliar control relais: 1A 230V~ RS232/Current Loop/RS485 _ 1A 24V~/V… selection jumper - Pan & Tilt: 24V~ or power supply 230V~ terminal blocks - power supply: communication 24 or 230V~ 50/60Hz terminal blocks 10W lenses control Pan&Tilt control output output DTMRX PTH900 lenses up to 99 receivers DTMRX PTH300 8 lenses DCMT8 8 • 24 DTRX TELEMETRY DATA RECEIVER TELEMETRY RECEIVER 17 FUNCTIONS • Microprocessor controlled • 17 functions • Preset option available • RS232, Current Loop or RS485 • Remote controllable up to 1500 m • Weatherproof standard IP65 The DTRX is a digital receiver, controlled by a microprocessor, for remote control of a pan & tilt motor, motor-driven zoom lens, _ wiper, washer and auxiliary contacts (12V… and 24V~ camera power supply, 2 auxiliary contacts). Connection to the control unit can be carried out in RS232, in RS485 or in Current Loop (in this case, the connection distance can reach 1500 m). This digital receiver can be controlled by DCS2, DCMT8 and DCS3 keyboards or by PC via RS232 serial DTRP connection. A IP65 weatherproof box ensures protection against all weather conditions. It is also possible to use TWT optional board for the twisted pair video transmission and DTRP board to recall up to 14 Pan & Tilt and optics preset positions with 4 local 8 alarms. 6 PG11 cable glands make connections easier. By means of a commutator, it is possible to select the pan & tilt power supply. Dimensions: 310 x 310 x 130 mm Weight: 3,5 Kg CODE 03/00 DESCRIPTION DTRX Telemetry receiver DTRP Preset board for P&T and zoom lens 8 • 25 DTRX TECHNICAL DOCUMENTATION DTRP card lens selection jumpers - speed: 1200/9600 baud - max length: 15 m (RS232), 1200m (RS485) or 1500 m (Current Loop) RS232 / Current Loop/RS485 selection jumpers 230V~ terminal block - Pan & Tilt, Auto pan - lens: zoom, focus e iris - addressable up to 99 units DTRX Reset switch Autotest switch Service power supply socket - control led video input BNC socket - 2 auxiliar relais: Telemetry receiver 17 functions 125V~ 0,3A data input - auxiliar power supply: _ 12V… for camera 24V~ for camera 24 o 230V~ for wiper 230V~ for washer RJ11 data output data output - Pan & Tilt: 24 or 230V~ - power supply: 230V~ 50/60Hz 50W up to 99 receivers PTH900 VIP5 IR300 DTRX DTRX DTRX DTRX DTRX 8 DCS2 DCMX DCS2 8 • 26 DCS2 DCS2 DTRXDC TELEMETRY DATA RECEIVER TELEMETRY RECEIVER 13 FUNCTIONS • Microprocessor controlled • 13 functions • RS232 or RS485 • Remote controllable up to 1200m • Preset standard • Weatherproof standard IP65 The DTRXDC is a digital receiver, controlled by microprocessor, for remote control of variable speed Pan & Tilt motor (PTH355P) and a motor-driven zoom lens. The connection to the control unit can be carried out in RS232 or in RS485 (in this case, the connection distance can reach 1200m). The digital receiver is controlled by DCS3 keyboard and it is possible to recall up to 14 Pan & Tilt and optics preset positions with 4 local alarms. NEW PRODUCT Two auxiliary control relays are available for controlling, for instance, the switching on and off of an IR illuminator, through a power contact. A IP65 weatherproof box ensures protection against all weather conditions. 8 Dimensions: 255 x 200 x 100 mm Weight: 1,8 Kg CODE DCS3 03/00 DTRXDC DESCRIPTION Data receiver - power supply 230 V~ 8 • 27 DTRXDC TECHNICAL DOCUMENTATION - speed: 1200/9600 baud - maximum length: 1200 m (RS485), autotest push-button 15 m (RS232) - Pan & Tilt DTRXDC - 8 Autopan speeds reset push-button - lens: zoom, focus e iris Telemetry receiver 13 functions - addressable up to 99 units - control led RS232/RS485 primary fuse selection jumper - 2 auxiliar control relays: RJ connector 1A 230V~ or main power supply for control input 1A 24V~ terminal blocks _ - Pan & Tilt: 24V… - power supply: 230V~ 50/60Hz 40W preset and alarms inputs pan & tilt control output data input and output lens control output DTRXDC PTH355P lenses up to 99 receivers DTRXDC PTH355P 8 lenses DCS3 8 • 28 DCMX CONTROL MULTIPLEXER TELEMETRY MULTIPLEXERS • Microprocessor controlled unit • 4 inputs - 8 data outputs • RS232 or Current Loop • Optional Rack 19” version DCMX is a serial data multiplexer, controlled by a microprocessor. It is used for the control of the same line of DTRX, DTMRX and MICRODEC receivers by more users (up to 4). The appliance gives serial data back on 8 outputs at the same time, allowing star configurations. For each of the 4 inputs it is possible to select the receiving mode between RS232 and Current Loop, whereas transmission takes place at the same time on all the 8 outputs in both modes. The multiplexer can be installed in Rack with RM1 or RM2 adaptors. Dimensions: 220 x 180 x 40 mm Weight: 1,8 Kg 8 CODE 03/00 DESCRIPTION DCMX Serial data controller RM1 RACK adaptor for 1 unit RM2 RACK adaptor for 2 units 8 • 29 DCMX TECHNICAL DOCUMENTATION - 4 inputs - 8 outputs - RS232 e Current Loop DCMX - speed: 1200/9600 baud - max. distance Serial data distributor 1500 m (Current Loop) 15 m (RS232) - Power supply: 4 inputs 230V~ 50/60Hz 10W DCS2 - DCMT8 8 outputs to DTRX - DTMRX - MICRODEC 1/8 outputs 4 inputs (receivers) (keyboards) 8 DCMX 8 • 30 RDDR-RDDT WIRELESS DATA TRANSMISSION RADIO TRANSMISSION SYSTEM FOR DIGITAL DATA • For indoor and outdoor installation • Frequency 433 MHz • RS232 1200 baud • Distance 700m (10 mW) • Weatherproof IP54 RDDR The system is composed by two devices: RDDR433 and RDDT433, digital data simplex radio receiver and transmitter. They allow transmission of RS232 digital signal. This system is ideal to overcome obstacles such as rivers, roads and all applications which make difficult cables installation. This device manages up to 32 channels by using the dip-switches aboard. Data transmission is RS232 1200 Baud while modulation is in FM narrow. These devices are available 10 mW power, allowing a maximum distance of 700 m. The entire system is housed in a IP54 weatherproof box. RDDT Dimensions: 200 x 120 x 60 mm 8 Weight: 0,5 Kg CODE 03/00 DESCRIPTION RDDR433 Wireless digital data receiver 433 MHz RDDT433 Wireless digital data transmitter 433 MHz 8 • 31 RDDR-RDDT RDDR433 RDDT433 Wireless system 8 8 • 32 - frequency: 433,875...434,875MHz - modulation: FM narrow - RF output power: 10 mW - channel step: 25KHz - inputs and outputs: RS232 1200 baud - 32 channels - power supply: _ 12V… , 50 mA TECHNICAL DOCUMENTATION SQ4M-SQ4C QUAD SWITCHER DIGITAL VIDEO COMPRESSOR • Color or black/white versions • 4 video inputs • 4 video outputs (Loop) • 4 alarm inputs, configurable as NC or NO • Image updating: 50 Fields/sec. • RS232 serial connection, 9600 baud A solution for small systems that allows you to connect up to four cameras with looping of the video signal on 4 outputs. It allows to display four cameras simultaneously or one individually onto full screen with images updated in real time and high resolution. The recording on VCR is carried out on quad signal, while the display of the recording can be in quad format with zoom to full screen for each quad. SQ4M: black and white digital compressor. The programming is through a screen menu, and also on screen is the warning of the NEW PRODUCT absence of a video signal and of the 4 alarms (NC or NO configurable). Dimensions: 435 x 170 x 49,5 mm Weight: 2,65 kg. SQ4C: colour digital video compressor. The cycling can take 8 place on quad and on full screen camera with programming through a screen menu, as well as the use of 4 alarms (NC or NO). The warning of the absence of a video signal and the display of the alarm are both on screen. Dimensions: 435 x 250 x 49,5 mm Weight: 2,8 Kg CODE 03/00 DESCRIPTION SQ4M Black and white digital video compressor SQ4C Color digital video compressor 8 • 33 SQ4M-SQ4C SQ4M, black and white SQ4C, color 8 TECHNICAL DOCUMENTATION - resolution: 720* 576 (CCIR/PAL) - 4 video inputs - 4 video outputs (Loop) - 4 alarm inputs, configurable as NC or NO - image updating: 50 Fields/sec - RS232 serial connection, baud rate 9600 - power supply: 230V~, <10W (SQ4M), 230V~, <20W (SQ4C) SQ4M/SQ4C 8 • 34