Transcript
EQU I P M EN T I N STA L L AT I O N
Quick Installation Guide
Quick Guía Guide
Door Lock Installation
Tools Needed • Herramientas necesarias • Outil
Tools Needed
Phillips Head Screwdriver Destornillador de cabeza de estrella Tournevis cruciforme
4 AA Batteries 4 baterías AA 4 piles AA
Parts in the Box • Piezas en la caja • Pieces dan
Phillips Head Screwdriver
4 AA Batteries
C (x2) ⁄4" • 2 mm
Ruler
A
Parts in the Box C (x2) ⁄4" • 2 mm
3
1 D (x2) 1 1⁄2" • 5 mm
D (x2) 1 1⁄2" • 5 mm
3
B
E (x2)
B
E (x2)
J (x2)
F
G
H
K
A
L
2
1
G
Check Dimensions Revise las medidas Vérifier les dimensions
Ruler Regla Règle
A
F
Check Dimensions
M
Install Latch & Strike Instale el pestillo y la placa Installer le verrou et la gâche
Phillip Desto Tourn
2A
If 2 3⁄8˝ (53 mm), proceed
If 2 3 ⁄4˝ (70 mm), twist to extend A
C
Ruler
A
3
Install Exterior Keypad Instale el teclado numérico exterior Installer le clavier extérieur
U
2
Install Latch & Strike Plate
P
2
Install Latch & Strike Plate Phillips Head Screwdriver
A
2A
B
C (x2)
D (x2)
2B
Latch
Jamb
Strike Plate
B
A
C
3
D
Install Exterior Keypad No Tools Needed F
!
U
P
F K L
4
Install Interior Mounting Plate Phillips Head Screwdriver
Cable goes underneath latch
K
L
L
4
Install Interior Mounting Plate Phillips Head Screwdriver
E (x2)
G
M
Interior
Keep parallel
M PU
PU
! Push cable into side hole.
G
Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (E). Remove key when fi nished.
E
!
Do not use electric drill or electric screwdriver to tighten screws.
5
Install Interior Assembly
5B Notch Down
Phillips Head Screwdriver
H
5A
J (x2)
Remove Cover & Battery Pack
! NOTE: Push excess cable into interior housing (H1).
H3
H2
H1
J H1
6
Install Batteries into Battery Pack
4 AA Batteries
6A
H3
)
x4 AA (
6B
!
IMPORTANT
(1) Hold LOCK button on keypad while (2) inserting the battery pack into the interior. The lock will extend & retract deadbolt latch. Hold down the lock button until you hear two beeps (approx. 30 seconds).
2
1
Interior
56 34
78
12
90
Exterior
7
Programming
Program Button
Keypad
7
Programming
Keypad
Program Button
Lock Button
How the keypad works Each button represents two numbers (i.e. 1 and 2 for the first button). You only need to push the button once to get either 1 or 2. For example: If your code is 1-2-5-6-8,
1
2
5
6
8
12
12
56
56
78
User Codes Code 1
Code 2
1
2
3
1
3
56
56 34
2
78
12
90
34 12
56
56 34
78
12
90
34
78 90
78
12
90
x2 Press Program Button
!
Enter 4 to 8 Digit Code
Press Lock Button
*Check code—press LOCK button & test code. If the code does not work, repeat the program step.
Press Program Button (x2)
Enter 4 to 8 Digit Code
Press Lock Button
CAUTION: Prevent unauthorized entry. This lock randomly set at the factory. Upon installation and setup, replace both of these codes with your own. Since anyone with access to the power board can change these codes, you must restrict access to the power board and routinely check both codes to assure they have not been altered without your knowledge.
Customizable Features Switches
Door lock status LED blinks every 5 seconds. ON
1 2 3 4
1 2 3 4
OFF
1 2 3 4
1 2 3 4 Auto Lock re-locks door 30 seconds after unlocking.
have not been altered without your knowledge.
Customizable Features Switches
Door lock status LED blinks every 5 seconds.
1 2 3 4
ON
1 2 3 4
1 2 3 4
1 2 3 4
OFF
Auto Lock re-locks door 30 seconds after unlocking.
1 2 3 4 Beeping sound enabled. When disabled, keypad buttons light red when pressed.
Status LED
1 2 3 4 Status LED Color
Lock Status
Green
Unlocked
Orange
Locked
Not a working switch
1 2 3 4
Red Low Battery
8
Incorrect Codes Entered—when three incorrect codes are entered the keypad will fl ash red and the beeper will sound for 15 seconds. The keypad will not allow input for 60 seconds after which you can re-enter a code and try again.
Install the Cover
No Tools Needed
H2
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
For assistance or warranty information: For Kwikset product, call 1-800-327-5625, USA & CANADA or visit www.kwikset.com For Weiser product, call 1-800-677-5625 USA, 1-800-501-9471 CANADA or visit www.weiserlock.com
26886-01 SmartCode Deadbolt Quick Installation Copyright © 2011 Stanley Black & Decker Corporation
You must activate your system and your online account before controlling your locks remotely. Before proceeding, please set up the rest of your system, then call 888.292.9368 for activation.
