1

Transcript

1 A distinctive, professional, functional and underslung Alware Pro Series Camera Mount is now launched to this wonderful RC world! This Pro V3 Camera Mount can be operated by an RC pilot or with a camera operator. It is steered by 2-3 channels to pan(optional), tilt and roll the camera. With this Pro Camera Mount Kit installed, the CG of the Aircraft will become lower. This will highly increase the stability for better aerial filming/ FPV activities. Differ from other Camera Mounts, Alware Pro Series Camera Mount operates with all fiber glass precise gears and high tolerance metal shafts. This greatly increase it's performance for professional aerial filming. Alware Pro V3 Camera Mount is made with lightest and strongest materials, Aluminum alloy and Fiber Glasses. All parts are manufactured by precise CNC technology which can produce a higher quality product. With double ball bearings design for every movement joints, Alware Pro V3 Camera Mount will be one of the best and professional Camera Mount for GAUI 330X(power system upgrade is required), GAUI 500X, Alware Spider 500, DJI F450/ 550 Multicopters and other 450-500 size Helicopters. This Pro V3 Camera Mount is 95% complete pre-assembled by well trained Technicians before releasing to the market so no worries about any installation time and issues. Alware 2/3-Axis F450-550 Pro V3 Camera Mount capable with Cameras/ DV Cameras up to the dimension of: 133*125mm(Wide*High), such as GoPro, 1080P HD Camcorder, Sony DCR-SX65 Camera, Sony AS3 etc. 2 Advanced upgraded benifits of V3: * CNC main shaft metal mount. * Operate with CNC fiber glass unique gears with better ratio for all axises which provide wider movement angles. * Larger room to hold bigger professional cameras (max. size 133*125mm(wide*height)). * Pan-axis can be fixed easily if necessary to reduce the total weight. * Larger 3-Dimension movement. * Strengthen Camera Stand Frame. * New Collapsible Landing Gear. * Zero tolerance on the Roll mechanism design. * Capable for GAUI 500X, Alware Spider 500 as well as DJI F425/550 Multicopters. - Also suitable for 450-500 size Helicopters. - With new, distinctive, professional, functional and underslung designed. - Steered by 2-3 channels to pan(optional), tilt and roll the camera with fiber glass precise gears and high tolerance metal shafts. - Controlled by 3x ALware MD260 Metal Digital Servo 260 Degrees which is a wide angle and powerful small size servo and is the best for camera mounts. - Double ball bearings design for every movement joints which provides precise movement for all axises. - Operate with unique fiber glass gears which highly increase the performance and movement angle of all axises. - 2D(X & Y Axises) Spirit Level included, easy to set the level point. - Made of flash, light and strong fiber glass plates as well as CNC Aluminum Metal Parts. - Manufacture by precise CNC technology. - Underslung mounting design which highly increase the stability of the aircraft in the sky due to lower CG position. - Relatively large room to mount varies cameras (Max. size 133*125mm(Wide*Height)). - 95% Pre-assembled and tested by well trained Technicians, no worries about any of the installation issue. 3 Control Axis: 2-3 Axis Controllable Camera mount [Pan(optional), Tilt, Roll] Mounting: Bottom plate assemble method Material: Flash, light and strong fiber glass plates, Unique CNC Fiber Glass Spur Gears; CNC Aluminum Rods and Mounts; High quality Flange Bearings and Screws. Bearing type: Flange Bearings Main Shaft Mount: CNC Anodized Metal Mounts Color: Black fiber plates; Silver anodize Aluminum parts. Dimension of portable camera: Max. 133*125mm(Wide*Height) Payload Capability: Up to 800g (But it is limited to the power of your Aircraft) Operate Servo size: Standard small size servos e.g. ALware MD260, Align DS410, SAVO SH-0261 etc. Gyro Stabilization for Camera Mount: Build in Gimbal stabilize function of some GPS systems (e.g. GAUI GU-INS, DJI WooKong-M etc), FY-30A 3-axises Stabilizer etc. Camera Mount Weight: ~480g (3-Axis Mode), 400g (2-Axis Mode) (Including Metal Gear Digital Servos) Max. Height: ~281mm Max. Length: ~296mm Max. Wide: ~275mm Pan Range: 0-85° Tilt Range: 0-90° Roll Range: 0-45° 4 Needle Nose Pliers Thread Locker Philips Screw Driver Hexagon Screw Driver head 2mm 5 Hexagon Screw Driver head 1.5mm ***Important Assembly Note: Apply a little amount of Thread Locker is a must when fixing metal parts or non-self-lock Nuts. 6 Parts 1: Installation Steps for Inner Circle Assembly 1. 2. 3. 4 Hex Cap Screw M2x10mm *9pcs 7. Hex Cap Screw M2x6mm *19pcs 8. M2 Nut *4pcs 9. Nylon Washer 3x1mm *2pcs 10. Flange Bearing 3x6x2.5mm *4pcs 12. Alu Sparer Rod 2x4x3.5mm *5pcs Alu Spacer Rod 3x5x4mm *2pcs M3x16mm Screw *2pcs Alu Square Rod 30.5mm Alu Rod M2x4x25mm *2pcs *9pcs 5. 6 M3 Self-Lock Nut *2pcs 11. 7 Nylon Washer 2x4x25mm *4pcs Prepare all the parts as shown on the picture. Install the Arc Gear on the middle of the Inner Circle Frame. (Part No.: 2, 3, 9) From another perspective. Insert the bearings in the Bearing Mount Frames with the aid of Needle Nose Pliers. (Part No.: 8) Install the servo like the picture. (Part No.: 1, 4) Install all the parts like the picture. (Part No.: 2, 3, 4, 12) 8 Install the Servo With Alu Square Rod 30.5mm to For the Cam Stand Frame, install the Spur Gear to the Inner Circle Frame using M2x6mm Hex Cap the Vertical Mounting Frame.(Part No.: 4, 7) And Screws. Make sure the direction of servo is install the Gear Assembly to the Mounting Frame correct. using 2pcs M2.5x6mm Hex Cap Screws. Side View. Insert M3x16mm Screw to the Bearing Mount and followed by two collars.(Part No.: 6, 10, 11) Secure the Cam Stand Assembly to the Inner Circle Assembly using M3 Self-lock Nuts.(Part No.: 5) Complete Assembly. 9 Part 2: Installation Steps for Outer Circle Assembly 1. Alu Rod 39mm *8pcs 6. Hex Cap Screw 2x12mm *4pcs 10. Hexagonal Nylon Rod M3X12mm *2pcs 2. 3. Alu Roll Bearing Alu Spacer Rod shaft 39mm *4pcs 2X4X4.25mm *4pcs 7. 8. Hex Cap Screw 2x6mm *26pcs 11. Hex Cap Screw 2x8mm *2pcs 12. 4. 5. Flange Bearing 3x7x3mm *8pcs 9. M2 Nut *2pcs Washers 2.5X6.0.4mm *4pcs 13. Hexagonal Nylon Nylon Screw M3X6 Nylon Washer 3mm Rod M3X15mm *4pcs *16pcs *2pcs 10 14. Alu Square Rod 30.5mm *2pcs Instal all the Alu Rod with the Outer Frame use M2x6mm screws.(Part No.: 1, 7) Check the parts for Part 2 like the picture. Insert the Flange Bearings and Nylon Washer to Stick the Alu Main Shaft Block with the Outer the Alu Rods.(Part No.: 2, 4, 13) Frame.(Make sure the direction of Alu Main Shaft Block is correct.) using M2x5 Screws. Install the Alu Roll Bearing shaft to the Outer Frame using M2x6mm Hex Cap Screws and washers for two upper holes(shown on next step). 11 Add the washer on the place like the picture. Put the Inner Circle Assembly to the Outer Frame . Make sure that Four Flange Bearings on the Outer Frame is supporting the Inner Circle Assembly (Make sure the installation direction is correct. ) tightly and correctly. Put the 4pcs Outer Frame Rib to the Outer Frame. Prepare the Landing Gear Ribs. Assembly the Landing Gear Rib with Nylon parts. Install the Landing Gear Rib with Frame as shown (Parts No.: 10,12 for center; Parts No.: 11 for above. (Installation direction should be the same Hexagonal Holes.) for both side.) 12 Insert the Outer Frame and secure it with M2X6mm Hex Cap Screws and with 2pcs Washers.(Part No.: 7, 9) Install 4pcs Flange Bearings and 8pcs Nylon washers again.(Part No.: 4, 13) Install second servo like the picture. Make sure Hole and compress two Alu Roll Bearing shafts with hand and tighten the shafts using M2x6 Hex the installation direction is correct.(With Parts No.: 3, 6, 14) Cap Screws .(This step will affect the smoothness and tolerance of the Roll Axis movement.) Install third servo with M2x8mm Hex Cap Screws and M2 Nuts.Make sure the direction is correct. (Part No.: 5, 8) 13 That is the end of Part 2. Part 3: Installation Steps for Fold-able Landing Gears 1. 2. 3. 4. Nylon Screw M3x6mm *12pcs 5. Nylon Screw M3x8mm *4pcs 6. Hex Nylon Rod M3x12mm *2pcs 7. Hex Nylon Rod M3x15mm *6pcs 8. Hand Knob Screw *2pcs M3 Set Screw *2pcs M2 Nut *4pcs 9. 10. 11. Steel 8mm Main Shaft *1pcs 12. Alu 8mm Collar *1pcs Alu 8mm Hub *1pcs Hex Cap Screw M2x4mm *12pcs Hex Cap Screw M2x6mm *4pcs 14 Prepare the parts as shown above. Install the Landing Gear Frame with Nylon Screw M3x6mm and Hexagonal Nylon Rod 3x15mm. (Part No.: 1, 4) Connect the Landing Gear Assembly to the Landing Gear Rib. Connect them with Part No.: 1, 2, 3 and 5.(Same for two Legs) Install the Large Spur Gear with parts No. 7, 10, Insert the Steel Main Shaft to the Alu Main Shaft Block and secure it with M3 set screw. 12. For the other Small Gears, connect them with (Part No.: 6, 8, 9) the Round Servo Horns using M2x4mm screws. (No Nut is needed, directly thread the Screw to the Servo Horn.)(Part No.: 11) 15 Set all Servos back to it's central position using Adjusted the position of the Servos as to obtain a receiver etc. Then install All the Spur Gears with perfect movement with less tolerance for all 3-Axis Servo Horn to the Servos and Main Shaft like the movement. picture. Use M3 Set Screws to secure the Large Spur Gear Assembly to the main shaft. (Part No.: 6) Install the Mounting Frame to the Large Assembly with 4pcs M2.5x6mm Hex Cap Screws. 16 Completed Final Assembly. Steps to change for 2-Axis Mode: (Recommended when using on RC Helicopters or if you want to reduce the weight of this Pro Camera Mount) For the Steel Main shaft block. You can remove one or two as you like. Remove the parts like the picture. Install the Al Square Rod 30.5mm disassembled Then install the Mounting Frame to the Alu Square previously to the new position of the Outer Frame Rod 30.5mm using 4pcs M2.5x6mm Hex Cap Screws. as shown above. Side View. 17 Mounting Instruction to GAUI 500X QuadFlyer: Step 1. Step 2. Unscrew four screws on the bottom frame of GAUI Screw four pieces M2 Copper Connectors to the 500X. GAUI 500X. Step 3. Step 4. Install four M2x4x39mm Alu Rods to the M2 Copper Connectors. Step 5. The four 2mm holes shown above is used to mount on GAUI 500X. Step 6. Install the Pro Camera Mount to the GAUI 500X using four M2x6mm Hex Cap Screws. Completed view of GAUI 500X with Pro Camera Mount. 18 Mounting Instruction to Alware Spider 500 QuadFlyer: Step 1. Step 2. The four 2mm holes shown above is used to mount on Alware Spider 500. Step 3. Install four M2x4x39mm Alu Rods to the mounting plate of the Pro camera mount using four M2x6mm Hex Cap Screws. Step 4. Install the Lower Frame of Alware Spider 500 to the Pro Camera Mount using four M2x6mm Hex Cap Screws to the holes shown above. Step 5. Step 6. Side View. Complete assembly. Front View. 19 Mounting Instruction to DJI F450/ F550 Multicopters: DJI Mounting Frame *4pcs Alu Rod M3x40mm *4pcs Hex Cap Screw M3x12mm *4pcs Hex Cap Screw M3x8mm *4pcs Install four Alu rod M3x40mm to the 3mm holes o Insert F450 / F550 Lower Main Frame in between the Mounting Frame using 4pcs of Hex Cap Screw two pcs of DJI Mounting Frames and secure it M3x8mm. (Use the Red holes for F550 using 2pcs of Hex Cap Screw M3x12mm.(Repeat HexCopter, Green holes for F450 QuafCopter.) this step by using another 2pcs of DJI Mounting Frames.) Final Assembly with F450 Lower Mounting Frame. Final Assembly with F550 Lower Mounting Frame. 20 Mounting Instruction to 450 Size Helicopters: Mount the Landing Gear of 450 size helicopters to the Pro Camera Mounting Frame directly using Zip Ties. Final Assembly. 21 Side View. Battery Mounting Demonstration: Used with one 4S 3700mAh Lipo Battery. Used with two 4S 2200mAh Lipo Batteries.(will be connected in parallel) Or other mounting methods which is suitable for your needs. Used with two 4S 2200mAh Lipo Batteries.(will be connected in parallel) Related testing videos can be referred to: http://www.youtube.com/user/alwarerc End of Manual Thank you for your support! 22