Transcript
CONTENTS REMOTE CONTROL ..................................................................... 3 HOPPING CODE ANTI-SCAN TECNOLOGY ............................... 3 CODE LEARNING ......................................................................... 3 ARMING ........................................................................................ 4 MUTE ARMING ............................................................................. 4 DISARMING .................................................................................. 5 MUTE DISARMING ....................................................................... 5 AUTOMATIC ARMING WITH DOOR LOCKS ............................... 5 REMINDER FOR PASSIVE ARMING WITHOUT DOOR LOCK ... 6 AUTOMATIC REARMING ............................................................. 6 TRIGGER ALARMING................................................................... 7 PAUSE TRIGGER ALARMING ..................................................... 7 ARM BYPASS DEFECTIVE ZONE ............................................... 7 FALSE ALARMING BYPASS........................................................ 7 CAR FINDER................................................................................. 8 MUTE CAR FINDER...................................................................... 8 PANIC MODE ................................................................................ 8 TRUNK RELEASE......................................................................... 8 CHANNEL 2 OUTPUT(CH2) ......................................................... 9 CHANNEL 3 OUTPUT(CH3) ......................................................... 9 DUAL STAGE SHOCK SENSOR .................................................. 9 ARM BYPASS SHOCK SENSOR ................................................. 9 ULTRASONIC SENSOR(OPTIONAL)......................................... 10 ARM BYPASS ULTRASONIC SENSOR ..................................... 10 ARM BYPASS OTHER SENSORS AND DOOR TRIGGERS ..... 10 LIGHTS REMINDING FOR DOOR OPENNING .......................... 10 VALET MODE...............................................................................11 ANTI CAR-JACKING VIA TRANSMITTER ..................................11 ANTI CAR-JACKING BY DOOR OPENING.................................11 ANTI CAR-JACKING BY IGNITION.............................................11 EXIT ANTI CAR-JACKING.......................................................... 12 1
EMERGENCY OVERRIDE .......................................................... 12 PIN CODE (PERSONAL SECURITY CODE) .............................. 12 PIN CODE PROGRAMMING....................................................... 12 DOUBLE PULSE DOOR LOCK/UNLOCK.................................. 14 DOOR LOCK/UNLOCK WHEN IGNITION ON/OFF.................... 14 LED INDICATOR ......................................................................... 14 SENSORS INPUT........................................................................ 15 RESETING THE SYSTEM........................................................... 15 JUMPERS PROGRAMMING....................................................... 15 SYSTEM PROGRAMMING ......................................................... 16 PROGRAMMING TABLE ............................................................ 17 INSTALATION DIAGRAM ........................................................... 19 INSTALATION FOR DOOR LOCS .............................................. 20
2
REMOTE CONTROL The transmitter has 4 buttons: Button #1
Lock
Button #2
Unlock
Button #3
Mute
Button #4 Ring/Trunk The system can memorize up to 4 transmitters. HOPPING CODE ANTI-SCAN TECNOLOGY The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re transmit at a later time to disarm your system. However, with this ANTI-SCAN technology HOPPING CODE, your anti code-grabbing transmitters will change their signal every time the button is pressed, so when a thief grabs then re transmits your signal, the alarm system will not respond and its code won’t be coppied. CODE LEARNING 1. Turn the ignition to ON 2. Press the valet button 4 times within 3 seconds. The siren will respond with 4 long chirps. 3. Press any button of the 1st new transmitter to be coded. The siren will respond with 1 chirp. 4. Press any button of the 2nd new transmitter to be coded. The siren will respond with 2 chirps. Repeat the same step for 3rd and 4th transmitter, the siren will chirp respectively. 3
5.
After all 4 transmitters are coded, the siren will respond with 2 long chirps to confirm the successful coding and exit automatically. Notes: 1. During the code learning procedure, if there is no operation in 10 seconds, the system will exit the code learning mode automatically. By switching the ignition OFF, it can also exit the learning mode. The siren will respond with 2 long chirps as confirmation. 2. When adding a new transmitter, all transmitters have to be coded in one time. The system can memorize up to 4 transmitters. ARMING In disarm status, press button 1 once, the direction lights will flash once and the siren will chirp once, all the doors will be locked, the power window will raise up (if equiped), and the engine will be blocked in 15seconds. 45seconds later(can be programmed as 0seconds delay, see Programmable Funtion F3), the system starts to detect signals from door switch, 30seconds later, the system starts to detect signals from shock sensor and ultrasonic sensor. LED indicator starts flashing once per second to indicate that the system is already armed fully. MUTE ARMING In disarm status, press button 3 once, then press button 1 once within 5 seconds, the direction lights will flash once, but the siren won’t chirp, all the doors will be locked, the power window will raise up (if equiped) and the engine will be blocked in 15 seconds. 45seconds later(can be programmed as 0seconds delay, see Programmable Funtion F3), the system starts to detect signals from door switch, 30 seconds later, the system starts to detect signals from shock sensor and ultrasonic sensor. LED indicator starts 4
flashing once per second to indicate that the system is already armed fully. If any zone is triggered, the system will alarm with siren chirps and direction light flashes. DISARMING In arm status, press button 2 once, the direction lights will flash twice and the siren will chirp twice, all doors will be unlocked, LED indicator flashes fast for 10seconds to indicate that the system is going into 60 seconds countdown of “Automatic Re-arming”. If the system has been triggered in arm status, siren chirps 4 times and direction lights flash 4 times to alert the car owner. MUTE DISARMING In arm status, press button 3 once, then press button 2 once within 5 seconds, the direction lights will flash twice, but the siren won’t chirp, all doors will be unlocked, LED indicator flashes fast for 10 seconds to indicate that the system is going into 60 seconds countdown of “Automatic Re-arming”. If the system has been triggered in arm status, the direction lights will flash 4 times to alert the car owner, but the siren won’t chip. AUTOMATIC ARMING WITH DOOR LOCKS (PROGRAMABLE F2) In Ignition OFF situation, when the last door is closed, the LED indicator flashes fast for 10 seconds to indicate that the system is going into 30seconds countdown of “Passive Arming”. Open any door within this 30 seconds will suspend the countdown, which will start again after closing the last door. To prevent the passive arming function when someone is inside the car, turn ignition key to ON and then to OFF, the LED indicator will turn OFF. Open and close doors well, the Automatic Arming function can be re-actived again. 5
After the 30 seconds countdown is finished, the system will be armed, the direction lights will flash once, siren will chirp once, all doors will be locked, the power window will raise up(if equipped), the engine will be blocked in 15 seconds. 45 seconds later(can be programmed as 0seconds delay, see Programmable Funtion F3), the system starts to detect signals from door switch, 30 seconds later, the system starts to detect signals from shock sensor and ultrasonic sensor. LED indicator starts flashing once per second to indicate that the system is already armed fully. NOTES: 1. The funtion of AUTOMATIC ARMING is programmable by Jumper J1, see the Programming Funtions of Jumpers. 2. This feature can be programmed as “Arming but without locking doors”, see funtion F2 of the Programming Table. REMINDER FOR PASSIVE ARMING WITHOUT DOOR LOCK If “Passive Arming without door lock”feature(see programmable funtion F2) is activated, 30 seconds after closing the last door, the system will be armed, siren will respond with 3 long chirps to remind that the doors are still unlocked, car owner can lock the doors manually by pressing button 1. AUTOMATIC REARMING (PROGRAMABLE F1) After the system is disarmed with fast LED flash, if either door, trunk or ACC is not opened, system will be re-armed automatically in 60seconds. Open any door, trunk or ACC will suspend the 60seconds countdown, and the system will be disarmed completely, LED indicator goes OFF. After the 60seconds countdown is finished, system will be armed, direction lights will flash once and the siren will chirp once, LED indicator flashes once per second to indicate that the system is already armed fully. 6
TRIGGER ALARMING 1. In arm or disarm status, press button 1 for 3 seconds(Panic function), the system will be triggered manually, the siren will chirp for 30 seconds and the direction lights will flash 30 seconds; to deactivate the panic funtion, press any button once of the transmitter. 2. In arm status, system can be triggered by any protected area. 3. Light impact of shock sensor: when it is triggered, the siren will chirp 5 times and the direction lights will flash 5 times. 4. Heavy impact of shock sensor: when it is triggered, the siren will chirp for 30 seconds and the direction lights will flash 30 seconds, the LED flashes fast. PAUSE TRIGGER ALARMING In alarming status, press any button once, the alarming will be paused while the system is still in arm status. ARM BYPASS DEFECTIVE ZONE In arm status, if there is any unclosed door or trunk, the siren will chirp 3 times and the direction lights will flash 3 times to remind the car owner to close all doors well. If the door remains open, the system will arm bypass the defective zone to protect the other zones normally. FALSE ALARMING BYPASS In arm status, if the system keeps receiving false trigger signals from any protected zone continuously, it will alarm for 30seconds/cycle, and maximum 4 cycles continuously. Then the system will bypass the false area automatically, the rest of the areas are still under protection. After the false area is recovered or when the system is re-armed, it will start to detect and protect all areas again. 7
CAR FINDER 60 seconds after the system is armed, press button 1 once, the direction lights will flash 6 times along with 3 siren chirps in order to locate the car’s position. MUTE CAR FINDER 60 seconds after the system is armed, press button 3 once, then within 5 seconds press button 1 once, the direction lights will flash 6 times but the siren won’t chirp to locate the car’s position. PANIC MODE In arm status, press and hold button 1 for 3 seconds and there will be a long chirp for the siren and the direction lights flashes quickly. To cancel this function, press any button of the transmitter once. TRUNK RELEASE (PROGRAMABLE F5) This funtion will make you open the trunk with the remote control. There are 2 ways for the trunk release. 1. For the remote control with 4 buttons, press and hold the button 4 for 3 seconds, the trunk will automatically open and and the system will be disarmed simutaniously. NOTES: This way could be programmed as “Trunk release but without disarm the system”. See the Funtion F5 of the programming table. In this case, the system won’t detect the trigger of shock sensor immediately after 45 seconds. 2. For the remote control with 3 buttons, Press and hold the button 2 for 3 seconds to disarm the system first, then press and hold the button 2 in order to open the trunk. NOTES: In this case, the programming funtion F5 needs to set as DISARM THE SYSTEM. If the vehicle does not have an original electric trunk, a universal one can be acquired. 8
CHANNEL 2 OUTPUT(CH2) There are 2 options for CH2 output as below: (see Funtion F7 of the Programming Table) 1. DOME LIGHT: After disarmed, the dome light will turn on for 30 seconds to see inside the vehicle and will turn off when the ignition key is turned ON or when the system is armed. 2. NEGATIVE HORN OUTPUT(-): The signal of the horn output is identical to the original horn, but it is negative, it requires an additional relay for the connection.
CHANNEL 3 OUTPUT(CH3) There are 2 options for CH3 output as below: (see Funtion F6 of the Programming Table) 1. Power Window Raising Output: Upon a lock signal, the channel 3 wire will output a 30sec signal to raise up windows, press button 2 once will stop the output signal. 2. Momentary output: Press and hold button#3 for 1.5sec, the channel 3 wire will output signal immediately and continue until the button#3 is released. DUAL STAGE SHOCK SENSOR 30seconds after armed, if the vehicle is softly hit, the system will respond with 5 short chirps and lights will flash 5 times. If the vehicle is strongly hit, the siren will sound for 30 seconds and direction lights will flash for 30secs simutaniously. ARM BYPASS SHOCK SENSOR Press the button 1 once, and then press button 3 once in 9
3seconds. The siren will respond with a long chirp to indicate that the system has been armed but without the shock sensor protection. ULTRASONIC SENSOR(OPTIONAL) 30seconds after armed, if system is triggered by ultrasonic sensor, the siren will sound for 30 seconds and direction lights will flash simutaniously. In status of ACC ON, the ultrasonic sensor will be deactivated. To anti-false alarming caused by heavy rain or crowded surroundings, if ultrasonic sensor is triggered for 4times continuously, it will pause working, and will back to work automatically when there is no triggering input for more than 1hour. ARM BYPASS ULTRASONIC SENSOR Press the button 1 once, and then press button 3 once in 3seconds. The siren will respond with 1 long chirp to indicate that the system has been armed but without the ultrasonic sensor protection. ARM BYPASS OTHER SENSORS AND DOOR TRIGGERS Press the button 1 once, and then press button 2 once in 3seconds. The siren will respond with 1 long chirp to indicate that the system has been armed but bypass the protection of shock sensor, ultrasonic sensor and door triggers, the system will be alarming only when the ignition is turned ON. LIGHTS REMINDING FOR DOOR OPENNING (PROGRAMABLE F16) In the status of ACC ON or ACC OFF, everytime when the door is opened, the direction lights will flash for 15 times as reminding until the door is closed. 10
VALET MODE Use this feature when the vehicle is taken to service. Valet button was installed to a hidden place inside the car. 1. Turn the ignition to ON position 2. Keep the valet switch pressed for 5 seconds 3. The LED will remain ON to indicate that system is in Valet Mode, alarm functions will be disabled in valet mode. However, the transmitter still work for keyless entry function. The panic and open trunk feature is available also. To exit Valet Mode, repeat step1 and step2, LED will turn off to indicate that the system back to normal. ANTI CAR-JACKING VIA TRANSMITTER (PROGRAMABLE FUNTION F13) After ignition ON, simultaneously press button 1 and button 3 for three seconds, the anti car-jacking will be activated. ANTI CAR-JACKING BY DOOR OPENING (PROGRAMABLE FUNTION F14) After ignition ON, opening and closing the door will activate the anti car-jacking. ANTI CAR-JACKING BY IGNITION (PROGRAMABLE FUNTION F12) Everytime when switching ignition ON, the anti car-jacking mode will be activated. Within the 30seconds, press the valet button once, you could exit the anti-carjacking by ignition, but after 30secs, you need to enter the Emergency Override by pressing the valet switch to deactivate the anti-carjacking mode. After actived by any of above 3 alternatives, direction lights will flash twice. After 30 seconds the LED will flash quickly and the lights will flash intermittently; after 15 seconds(i.e. 45sec later) the engine will start to block and after another 15 seconds(i.e. 60sec 11
later) the vehicle will turn off and remain blocked. If the system is connected to the door locks and windows, they will automatically close when the engine turns off. EXIT ANTI CAR-JACKING To exit anti carjacking in the beginning 30seconds, with the engine is started or the ignition key in ON position, press the valet button once or press button 2 once to exit the anti car-jacking mode. But after the 30seconds when hear siren chirps, it’s necessory to proceed with Emergency Override operation to exit the anti-carjacking. EMERGENCY OVERRIDE If the remote control is lost or broken, please disarm the system with the valet switch. 1. In alarming status, turn the ignition from the position OFF to ON; 2. Then press the valet switch once(See PIN CODE, default is 1), the system will be disarmed in 2 seconds. NOTES: 1. If the PIN CODE is already set as the personal code, enter the times of the personal code, then 2 seconds later the system will be disarmed. 2. If the code is entered incorrectly, turn the Ignition from OFF to ON and then enter the correct code to disarm the system. 3. PIN CODE (PERSONAL SECURITY CODE) It will always be necessary to introduce the default (1) or personal (in case this was changed) PIN CODE in order to use the following feature: Emergency manual disarming without transmitter Anti car-jacking deactivation PIN CODE PROGRAMMING 12
The default PIN CODE is 1 which means that the valet button must be pressed one time to cancel anti car-jacking or for the emergency manual disarming. To change the default PIN CODE, the following procedure must be followed: 1. Enter valet mode 2. Turn the ignition to OFF 3. Change the key position 3 times from OFF to ON and finally stay in OFF position, see as follows: (OFF - ON) (OFF - ON) (OFF - ON) (OFF) 4. The siren emits one chirp to confirm that the PIN CODE programming mode has been entered. 5. The new PIN CODE can be any number from 1 to 9, which is the number of times that the valet button has to be pressed. Example: If the desired PIN CODE will be 6, then the valet button has to be pressed 6 times. 6. When introducing the new PIN CODE, each time when the valet button is pressed once, the siren will chirp once to confirm the code. 7. Then the siren will emit 2 chirps to indicate that the system exit the programming mode and that it has returned to disarmed mode. If the new PIN CODE can not be remembered and it is different from 1, the following procedure must be done to restore the PIN CODE to its default 1: 1. Turn the ignition to ON 2. Open any door 3. Press 3 times the valet button and keep it pressed the last time for 10 seconds 4. The system will enter disarm mode and the PIN CPDE will be restored to its default (1) 13
DOUBLE PULSE DOOR LOCK/UNLOCK (PROGRAMABLE FUNTION F10/F11) If the car alarm system is programmed with Double Pulse Door Lock/Unlock(see Funtion F10/F11 of the Programming Table)(Default is only one pulse). When arming/disarming by pressing button 1 or button 2 once, the system will send two pulses subsequently to lock/unlock the doors. DOOR LOCK/UNLOCK WHEN IGNITION ON/OFF (PROGRAMABLE FUNTION F8) If a central door locking system is connected to the car alarm system, turn ignition ON the system will automatically locks the doors and turn ignition OFF it will automatically unlock the doors, but if there is any opening doors, doors will not be locked when starting the vehicle. Notes: This funtion is programmable, see Funtion F8 of the Programming Table. LED INDICATOR 1. If “Passive arming with door locks” function is enabled, turn ignition ON, LED indicator will flash quickly for 5 seconds and then it will be turned off automatically; 2. In triggered and alarming situation, LED indicator will flash fast until the alarming stopped; 3. After disarmed, LED indicator flashes fast for 10seconds during the count down of “Automatic Re-arm”; 4. If “Anti-carjacking by ignition” function is enabled, turn ignition ON, LED indicator will flash 1 time with 1second interval and it will remain for 10seconds as a reminder; 5. If “Anti-carjacking by door open” function is enabled, turn ignition ON, LED indicator will flash twice with 1second interval and it will remain for 10seconds as a reminder. 14
SENSORS INPUT 1 STAGE(Without prealarming): There won’t be prealarming for the sensor. With activating the sensor, there will be only one same alarming sound as Bi…Bi…Bi…like radars. 2 STAGES(With prealarming): The sensor will work normally with prealarmingl If the vehicle is light hit, the system will respond with 5 short chirps and lights will flash 5 times. If the vehicle is strongly hit, the siren will sound for 30 seconds and direction lights will flash simutaniously. RESETING THE SYSTEM To reset the system and roll back the features to its default setting, the following procedures must be followed: 1. Turn the ignition to ON or start the engine; 2. Keep the valet button pressed for 5 seconds. The LED will remain ON(VALET MODE); 3. Press the valet button 3 times and the siren will respond with a long chirp to indicate the system has entered programming mode. 4. Keep the button 3 pressed for 5 seconds and the siren will respond with 6 chirps and the lights will also flash 6 times to confirm that the system has been reset. To exit the programming mode, turn the ignition OFF and the siren will respond with 3 chirps to indicate that the new settings have been saved into the system memory. JUMPERS PROGRAMMING With Without Jumper Funtions Jumper Jumper 1 Automatic Rearming ON OFF 0.5s Door lock pulse 3.5s 2 (Electronic/Neumatic) (Electronic) (Neumatic) REMARKS: Factory setting is with Jumpers(in grey background). 15
SYSTEM PROGRAMMING 1. Turn the ignition to ON 2. Press the valet button for 5 seconds. The LED will remain ON (valet mode) 3. Press the valet button 3 times and the siren will respond with a long chirp to indicate the system has entered programming mode. 4. Press the valet button the number according to the feature desired (see programming table) siren will respond with confirmation chirps according to the number of valet button pressed: Confirmation chirp Number of valet button pressed 1~4 short chirps 1~4 times 1 long chirp 5 times Example: Pressing the valet button 8 times will cause the siren to respond with 1 long chirp and 3 short chirps to confirm the system is in the programmable feature number 8 Pressing the valet button 14 times will cause the siren to respond with 2 long chirp and 4 short chirps to confirm the system is in the programmable feature number 14 The desired programmable function can be entered without any particular order. 5. Press the button from the transmitter that corresponds to the feature number 6. The siren will respond with 1 to 2 chirps to confirm the feature selected and memorized. 7. The system will exit the programming mode automatically if there is no operation in 10 seconds.
16
Valet
PROGRAMMING TABLE Button 1 Feature (1chirp)
1
Automatic Rearming
2
Passive arming door locks
3 4
5
with
Arming with door switch delay Arming /Disarming with sound Trunk release
6
Channel 3 Output(CH3)
7
Channel 2 Output(CH2)
8
Door lock/unlock ignition ON/OFF
9
Sensor input
10
Door locking pulse
11
Door unlocking pulse
ON
OFF
ON (With door lock)
OFF (Without door lock)
45sec
0sec
ON
OFF
Disarming
W/O disarming (Only for 4buttons)
Power window raising 30sec (-) Dome Light 30sec(-)
by
17
Button 2 (2chirps)
Momentary Output (-) Horn Output(-)
ON
OFF
2 Stages
1 stage
1 pulse 0.5sec 1 pulse 0.5sec
Double pulse 0.5sec Double pulse 0.5sec
12 13 14 15
Anti car-jacking by ignition Anti car-jacking by transmitter Anti car-jacking by door opening Anti car-jacking activation with sound
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Lights reminding for ON door openning REMARKS: Default funtion is in grey background. 16
18
OFF
INSTALATION DIAGRAM
19
INSTALATION FOR DOOR LOCS
20
21
22
