Transcript
Speed fader
Use to receive audio signal for sound activated
DC 9V 300mA min
Output DMX signal to the connected fixture
Input DMX signal to the connected fixture
DMX Output
DMX Input
Translate between 4 addresses mode and 8 addresses mode
Channel Mode Switch
DC Input
Turn On/Off the power
Power Switch
Rear View:
All lighting effect at once
Full on
Blackout the fixture
Sound to chase
Black out
Use to dimmer / shutter the fixture
Use to adjust fade time. Fade time is amount of one color to fade in or fade out
Use to adjust chase speed in the range of 0.1 to 2.5 seconds
Spectrum Mix fader
Fade Time fader Master fader
Use to select 32 spectrum mix colors in Spectrum mix mode.
Chase 1 fader
2. In Chase 2 mode (the LED blinking), use to select 8 chase or random chase.
1. In Fixed Color mode, use to select color on Red /Orange / Yellow / Green / cyan / Blue / Purple / Magenta /White
Use to select Fixed Color / Chase 1 / Chase 2 / Spectrum mix mode
In Chase 1 (the LED on) mode, use the fader to select color chases on Standard chase / Bright chase / Mood chase / spectrum random chase / Spectrum sequence chase / Dynamic chase / Red-Green+ Blue / Green-Red + Blue / Blue-Red / Yellow-Blue / Red-Green / Yellow-Green
Fixed color / chase
Mode select
Function Instructions:
Weight: 1 kg
Dimension: 180X 130 X 50 mm
Power supply: DC 9V 300 mA
Used together with CA-32F foot dimmer.
Full on and blackout functions
Speed and dimmer adjustable by fader
32 different mix colors, including color fade
12 different color chases triggered by music
9 different hold-color buttons for instant colors
Can connect witch LED-CC or LED-PC300/100 to control passive LED fixtures
A profession remote controller with 4Ch. /8Ch. Switchable
1. General Instructions Button
Attention: Before address setting, be sure DIP switches 0 to 9 of all lightings are in “OFF” position.
B. Connect with COLOR PAR/ CA-32F
A. Connect with COLOR BALL/COLOR SPOT/CA-32F
Please refer to the following diagram to connect the fixtures:
3. How to Connect the unit
h. The address of lightings in the chain will be 1234-1234-… (12345678-12345678-…)
g. Press the “black out” button for about 5 seconds to exit address setting.
f. Press “random” button to set address automatically.
e. Press the “sound to chase” or “full on” button until all LED lightings on.
d. The first LED lighting will be on.
c. Hold the “black out” button for about 5 seconds until the red indicator LED blinking.
b. Connecting all LED lightings to the LED-RC8F and power them on.
3, 4, 5, 6, 7, or 8) mode.
a. Set LED-RC8F to 4 Ch. (the address should be 1, 2, 3 or 4) or 8 Ch. (the address should be 1, 2,
Automatic address setting:
g. Press the “black out” button for about 5 seconds to exit address setting.
and addressing for them.
8
6
f. Press the “sound to chase” or “full on” button to select other fixtures,
7
5 Chase 6
e. Set address for the first lighting by pressing the chase 1-8 buttons.
d. The first LED lighting will be on.
Chase 8
4 Chase 5 Chase 7
3 Chase 4
LED blinking.
2 Chase 3
c. Hold the “black out” button for about 5 seconds until the red indicator
1
address
Chase 2
Chase 1
b. Connecting all LED lightings to the LED-RC8F and power them on.
(the address should be 1, 2, 3, 4, 5, 6, 7, or 8) mode.
a. Set LED-RC8F to 4 Ch. (the address should be 1, 2, 3 or 4) or 8 Ch.
Manual address setting:
you can set address for the LED lightings:
Each time you make a different connection, you have to reset the address. There are two ways that
2. Address setting
