Transcript
The leader in rugged fiber optic
RLH Industries, Inc.
technology.
USER GUIDE
U-052 2017C-0621
1 Plate
Slimline Patch Panel DIN RAIL OR WALL MOUNT Introduction RLH 1 Plate Slimline Patch Panel is designed for fiber optic patching and splicing applications where a wall mount or DIN rail unit is desired.
1 Plate Slimline Patch Panel
This sturdy steel enclosure, powder coated light grey, holds one adapter plate. Adapter plates are ordered separately and are available with ST, SC, FC, LC, MTRJ, UPC and APC style adapters. When ordered together the adapter plates come pre-installed. The side panel has a hinged door with easy to use plunger latches. Each patch panel includes an adhesive splice holder, fiber splice protection sleeves, distribution chart, cable mounting tie-downs and adhesive Velcro hook and straps for securing fiber cable. Self-sealing removable 3/4” grommets on the top and bottom of the enclosure allow a safe entrance and exit for the fiber cable. The patch panel can be wall mounted or DIN rail mounted depending on the application. All wall mounting hardware is included. Fiber cable assemblies or pigtails can be ordered and pre-installed into the enclosure for ease of installation.
Wall Mounted Example
KEY FEATURES Wall mounting hardware included
Holds 1 adapter plate
Optional heavy duty DIN-Rail clip
Hinged door with plunger latches
ST, SC, FC, LC, MTRJ, UPC, APC style adapters
Built in anchor points to secure fiber cable inside
Steel enclosure, powder coated light grey
Splice holder and fiber protection sleeves included
Includes adhesive Velcro hook and straps
for easy and flexible fiber management.
Self-sealing removable grommets (up to 3/4”) on the top and bottom Specifications subject to change without notice.
RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.fiberopticlink.com
Page " 1
Dimensions & Components The dimensional diagram below calls out important features of the Slimline Patch Panel. Listed below is a table of the included accessories found inside every patch panel.
6.3”
0.52”
Removable Grommet Access Latch Optional
DIN-Rail Mounting Kit
Top
Panel View
DIN-CLIP30
1.60”
Adapter
Plate
Additional Mounting Hole
Mounting Key Holes
Mounting
Key Holes
Hinged Door
0.32”
DIN Rail Clip
End Mounting
DIN Rail Clip
Side Mounting
7.0”
Front
Panel View
Internal
Side View
Rear
Panel View
Accessory Kit Components Included Distribution chart adhesive label
Velcro adhesive hook and straps - Qty. 2
12 Position adhesive splice holder
Cable ties - Qty. 3
Fiber protection sleeves - Qty. 15
Wall mount hardware
Page 2 "
RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.fiberopticlink.com
Mounting Choose a suitable location, with room for the door to open fully for easy access to the front. Pre-position the patch panel to plan out cable routings and check for any potential problems with the location. The patch panel allows it to be mounted facing multiple directions making it a flexible solution in the field.
Wall Mounting For wall mounting, once the position is determined, mark out the mounting points. Use the included 3/4” screws. For all other mounting applications, use appropriate mounting hardware as required.
x2
x3
Rear Panel
Side Panel
Wall Mounting Hole Locations Installation
Examples "
DIN Rail Mounting For DIN rail applications, mount the DIN Clip to the appropriate mounting holes depending on the position preferred for the solution. When installing the DIN Clip to the side panel use the lowest set of holes. This will center the DIN rail to the patch panel.
x4
Installation
Examples
Rear Panel
Side Panel
DIN Clip Mounting Hole Locations
"
RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.fiberopticlink.com
Page " 3
Ordering Information
Description
Capacity
Dimensions
Part Number
Slimline Patch Panel
1 Adapter Plate
W 6.3in. x H 7in. x D 1.6 in.
PWS1-A-1
DIN Rail Mounting Kit
-
-
DIN-CLIP30
Add -D to the end of the part number to have the DIN Rail Mounting Kit pre-installed. Adapter plates and fiber cable pigtails are ordered separately and may be preinstalled prior to shipping. Please contact your RLH sales representative for pricing and delivery information
Specifications
Adapter Plates
(Ordered Separately)
Connectors
Holds 1 plate
Up to 12 Fibers
ST
Simplex
SC
Simplex, Duplex
SC/APC
Simplex, Duplex
LC
Simplex, Duplex, Quad
MTRJ
Simplex
FC
Simplex
Mounting Style
Wall and DIN rail (DIN rail kit ordered separately or may be ordered pre-installed)
Environmental
Indoor style, 1 plate patch panel design
Construction
Powder coated steel, hinged door and plunger latches. Includes a 12 position adhesive splice holder, fiber protection sleeves, self sealing cable grommets,
cable ties, distribution chart, cable mounting adhesive Velcro hook and straps,
hardware and mounting hardware.
Dimensions
W 6.3 in. x H 7in. x D 1.6 in. (160mm x 178mm x 41mm)
* Not including latches
RLH Industries, Inc. 936 N. Main Street, Orange, CA 92867 USA T: (714) 532-1672 F: (714) 532-1885
"
Page 4 "
Please contact your RLH sales representative
for pricing and delivery information. Specifications subject to change without notice.
RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.fiberopticlink.com