Transcript
1
1 Unscrew both thumbscrews shipped with square foam on the component panel . Unscrew the thumbscrew caps from the base (3x), stand (4x), and HD display (2x). Discard the foam and set aside.
3
2
4
2 Place the base on the floor near the final location for the system. Remove the shipping foam from between the foundation and metal overlay. Turn the overlay so the most presentable side faces upward. 3 Insert the phone cable (from the phone box) and the VGA cable (from cable bag 1) through the cable channel that runs along the underside of the base and pull them through the hole in the center. Pull at least 1 m (3.3 ft) of the phone cable and 80 cm (32 in) of the VGA cable through the hole. Cables can be inserted into the cable channel from the front (shown) or back of the base. 4 Thread the phone cable and VGA cable through the hole in the bottom of the stand and place the stand on top of the base bolts. LifeSize recommends a second person to assist mounting the stand to the base. 5 Use 2 thumbscrew caps to secure the stand to the outer base bolts. Note: Do not secure the middle bolt at this time.
5
7
6
8
9
6 Facing the back of the speaker, thread the speaker’s AC power cable and audio cable (from cable bag 2) under the mounting bracket and connect them to the back of the speaker. 7 Mount the speaker vertically over the two bolts protruding from the center of the back of the stand, and use a thumbscrew cap to secure the speaker to the top bolt.
ON LEVEL MIN
MAX
Note: Secure only the top bolt at this time. 8 Insert the video system, back end facing up, into the middle brackets on the component panel. Adjust the brackets so the two fan ports on the video system are positioned directly beneath the rectangular hole in the panel. 9 Place the component panel inside the stand, using the bolt near the speaker and the middle bolt on the base as guides. Use 2 thumbscrew caps to secure the panel to both bolts. Ensure the speaker cables remain in front or to the side of the panel (but inside the stand) as you secure it.
11
10
10 Place the electronics box into the two brackets at the base of the component panel. Secure the box and panel to the stand with two thumbscrews. Ensure the phone cable remains to the left side of the electronics box (inside the stand) as you secure it. Similarly, ensure the VGA cable remains to the right of the electronics box.
4
2
11 Connect the free ends of the VGA cable, phone cable, and the speaker’s AC power cable and audio cable to the electronics box and video system, indicated by cables 1-4 on the wiring diagram. 12 Guide the 2 mounting bolts located on the upper back side of the display into the corresponding holes on the stand, and gently slide the display downward into place. Note: LifeSize recommends two people to mount the display.
1 3
12
13
13 Reach into the stand from beneath the display and secure the display to the stand with 2 thumbscrew caps.
8
14 Remove the cables from bag 3 and connect them from the display to the video system and electronics box, indicated by cables 5-8 on the wiring diagram.
14
15
18
19
7
Note: The display requires only 4 cables, even though it features 5 ports. 15 Use the camera screw to secure the camera to the top of the camera shelf. 16 Use 2 thumbscrew caps to secure the camera shelf to the back of the display. 17 Verify that the camera is secured to the shelf and that the shelf is secured to the stand.
6
18 Connect one end of the camera’s DC power cable and HD cable (from cable bag 4) to the back of the camera, and thread the other ends through the slot at the top of the stand.
17
16
5
19 Connect the free ends of the camera’s DC power cable and HD cable to the electronics box and video system, respectively, indicated by cables 9-10 on the wiring diagram.
9
20 Remove the cables from bag 5 and connect them from the video system to the appropriate component, indicated by cables 11-14 on the wiring diagram. 21 Connect one end of the network cable (from bag 6) and system AC power cable to the wall and the other end to the back of the electronics box, which is exposed through the hole in the lower back of the stand. Refer to cables 15-16 on the wiring diagram. 22 Turn on power and wait for the system to initialize. The first time, an Initial Configuration screen prompts you to configure the system. Refer to the LifeSize Video Communications Systems User and Administrator Guide for instructions.
10
20
23 Tuck loose cables inside the stand, insert the upper lip of the cover under the display, and press the cover toward the stand until it snaps into place.
14
11
12
13
21
22
23
LifeSize® Unity 500™ Wiring Diagram
Parts
10
1 Stand 1 Component Panel 1 Cover 1 Camera shelf 1 Camera screw 2 thumbscrews 9 thumbscrew caps Cables
1 LifeSize Express 220 (video system) 1 LifeSize Phone, Second Generation 1 LifeSize Camera 10x 1 HD display 1 Electronics box (INPx) 1 Speaker 1 Base foundation 1 Base overlay
9
Cables LifeSize Unity 500 ships with more cables than are necessary for assembly. Required cables include the phone cable shipped with the LifeSize Phone and various cables in the six cable bags that are included in the System Cables box. ON LEVEL MIN
3
MAX
4 2
8
7
14
1
11
DC power
Speaker AC power
Speaker Audio (RCA)
Network
Video
HD
12
13
5 6
15 16
