Transcript
2014 Chrysler 200 LX 2014 ENGINE Cooling System - 200 & Avenger
6 - CRANKSHAFT PULLEY 7 - WATER PUMP PULLEY 8 - ACCESSORY DRIVE BELT TENSIONER 9 - UPPER IDLER PULLEY 1. Using a wrench, rotate accessory drive belt tensioner (8) counterclockwise until accessory drive belt (2) can be removed from pulleys (5 and 9). 2. Remove accessory drive belt (2). 3.6L
Fig. 16: Belt Tensioner, Accessory Drive Belt & Belt Routing Courtesy of CHRYSLER GROUP, LLC CAUTION: Do not let tensioner arm snap back to the freearm position, severe damage may occur to the tensioner. 1. 2. 3. 4. 5.
Disconnect negative battery cable from battery. Raise vehicle. Remove right front wheel. Remove the inner splash shield. Rotate belt tensioner (8) until it contacts its stop. Remove belt (7), then slowly rotate the tensioner into the freearm position.
INSTALLATION 2.4L
2014 Chrysler 200 LX 2014 ENGINE Cooling System - 200 & Avenger
Fig. 17: Identifying Accessory Drive Belt - Gas Engine Courtesy of CHRYSLER GROUP, LLC 1 - POWER STEERING PUMP 2 - ACCESSORY DRIVE BELT 3 - GENERATOR 4 - CRANKSHAFT PULLEY 5 - LOWER IDLER PULLEY 6 - CRANKSHAFT PULLEY 7 - WATER PUMP PULLEY 8 - ACCESSORY DRIVE BELT TENSIONER 9 - UPPER IDLER PULLEY NOTE:
When installing drive belt on the pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves.
1. Install the accessory drive belt (2) around all the pulleys except for the generator pulley (3). 2. Using a wrench, rotate accessory drive belt tensioner (8) counterclockwise until accessory drive belt (2) can be installed on the generator pulley (3). Release spring tension onto accessory drive belt (2). 3.6L
2014 Chrysler 200 LX 2014 ENGINE Cooling System - 200 & Avenger
Fig. 18: Belt Tensioner, Accessory Drive Belt & Belt Routing Courtesy of CHRYSLER GROUP, LLC 1. Check condition of all pulleys. CAUTION: When installing the serpentine accessory drive belt, the belt MUST be routed correctly. If not, the engine may overheat due to the water pump rotating in the wrong direction. 2. Install new belt (7). Route the belt around all pulleys except the idler pulley (2). Rotate the tensioner arm (8) until it contacts its stop position. Route the belt (7) around the idler (2) and slowly let the tensioner (8) rotate into the belt. Make sure the belt (7) is seated onto all pulleys.
Fig. 19: Measurement A Courtesy of CHRYSLER GROUP, LLC
2014 Chrysler 200 LX 2014 ENGINE Cooling System - 200 & Avenger
3. With the drive belt installed, inspect the belt wear indicator. The gap between the tang and the housing stop (measurement A) must not exceed 24 mm (.94 inches). 4. Install the inner splash shield. 5. Install the wheel. 6. Lower vehicle. 7. Connect the negative battery. PULLEY, IDLER REMOVAL REMOVAL
Fig. 20: Accessory Drive Belt - World Engine Courtesy of CHRYSLER GROUP, LLC 1 - POWER STEERING PUMP 2 - ACCESSORY DRIVE BELT 3 - GENERATOR 4 - CRANKSHAFT PULLEY 5 - LOWER IDLER PULLEY 6 - CRANKSHAFT PULLEY 7 - WATER PUMP PULLEY 8 - ACCESSORY DRIVE BELT TENSIONER 9 - UPPER IDLER PULLEY 1. Raise vehicle on hoist. 2. Remove belt splash shield.
2014 Chrysler 200 LX 2014 ENGINE Cooling System - 200 & Avenger
3. Remove accessory drive belt. Refer to BELT, SERPENTINE, REMOVAL. 4. Remove idler pulley mounting bolt. Remove idler pulley (5 or 9). 3.6L
Fig. 21: Belt Tensioner, Accessory Drive Belt & Belt Routing Courtesy of CHRYSLER GROUP, LLC 1. 2. 3. 4.
Remove main drive belt (7). Refer to BELT, SERPENTINE, REMOVAL. Lower vehicle. Remove the air intake system. Remove the mounting bolt holding the idler pulley (2).
INSTALLATION INSTALLATION
