Transcript
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet Features
Compliant with SFF-8665/SFF-8679
Compliant with IEEE 802.3bj
4 independent full-duplex channels
Up to 25.78125 Gbps data rate per channel
Up to 5m transmission
Single 3.3V power supply
Low insertion loss
BER better than 10
Operating temperature: -5~+70℃
RoHS compliant
-15
Applications
40G/100G Ethernet
Infiniband, QDR/EDR
General Product Characteristics QSFP28 Copper Specifications Number of Lanes
4 Tx & 4 Rx
Channel Data Rate
25.78125 Gbps/channel
Operating Case Temperature
-5 to +70°C
Storage Temperature
-40 to +85°C
Supply Voltage
3.3V nominal
Electrical Interface
38-pin edge connector
Management Interface
Serial, I C
2
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 1 of 6
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet
High Speed Characteristics Parameter
Symbol
Min.
Max.
Units
Note
Differential Impedance
RIN,P-P
90
110
Ώ
Insertion loss
SDD21
22.48
dB
At 12.8906 GHz
SDD11
See 1
dB
At 0.05 to 4.1 GHz
SDD22
See 2
dB
At 4.1 to 19 GHz
dB
At 0.2 to 19 GHz
Differential Return Loss Common-mode to
SCC11
common-mode
2
output return loss
SCC22
Differential to common-mode
SCD11
See 3
return loss
SCD22
See 4
At 0.01 to 12.89 GHz dB At 12.89 to 19 GHz
10 Differential to common Mode Conversion Loss
SCD21
See 5
At 0.01 to 12.89 GHz dB
6.3 Channel Operating Margin
COM
3
At 12.89 to 15.7 GHz At 15.7 to 19 GHz
dB
Notes: 1. Reflection Coefficient given by equation SDD11(dB) < 16.5 - 2 × SQRT(f ), with f in GHz 2. Reflection Coefficient given by equation SDD11(dB) < 10.66 - 14 × log10(f/5.5), with f in GHz 3. Reflection Coefficient given by equation SCD11(dB) < 22 - (20/25.78)*f, with f in GHz 4. Reflection Coefficient given by equation SCD11(dB) < 15 - (6/25.78)*f, with f in GHz 5.
Reflection Coefficient given by equation SCD21(dB) < 27 - (29/22)*f, with f in GHz
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 2 of 6
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet
Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 1.
Logic
CML-I CML-I CML-I CML-I LVTTL-I LVTTL-I LVCMOSI/O LVCMOSI/O CML-O CML-O CML-O CML-O
CML-O CML-O CML-O CML-O LVTTL-O LVTTL-O
LVTTL-I CML-I CML-I CML-I CML-I
Symbol
Name/Description
GND Tx2n Tx2p GND Tx4n Tx4p GND ModSeIL ResetL Vcc Rx SCL SDA GND Rx3p Rx3n
Ground Transmitter Inverted Data Input Transmitter Non-Inverted Data Input Ground Transmitter Inverted Data Input Transmitter Non-Inverted Data Input Ground Module Select Module Reset +3.3V Power Supply Receiver 2-wire serial interface clock 2-wire serial interface data Ground Receiver Non-Inverted Data Output Receiver Inverted Data Output Ground Receiver Non-Inverted Data Output Receiver Inverted Data Output Ground Ground Receiver Inverted Data Output Receiver Non-Inverted Data Output Ground Receiver Inverted Data Output Receiver Non-Inverted Data Output Ground Module Present Interrupt +3.3V Power Supply transmitter +3.3V Power Supply Low Power Mode Ground Transmitter Non-Inverted Data Input Transmitter Inverted Data Input Ground Transmitter Non-Inverted Data Input Transmitter Inverted Data Input Ground
Rx1p Rx1n GND GND Rx2n Rx2p GND Rx4n Rx4p GND ModPrsL IntL Vcc Tx Vcc1 LPMode GND Tx3p Tx3n GND Tx1p Tx1n GND
Plug Sequence 1 3 3 1 3 3 1 3 3 2 3 3 1 3 3 1 3 3 1 1 3 3 1 3 3 1 3 3 2 2 3 1 3 3 1 3 3 1
Notes 1
1
1
2 2 1
1
1 1
1
1 2 2
1
1
1
GND is the symbol for signal and supply (power) common for the module. All are common within the module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.
2:
Vcc Rx, Vcc1 and Vcc Tx shall be applied concurrently. Requirements defined for the host side of the Host Edge Card Connector are listed in SFF-8679 Table5-6. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the module in any combination. The connector pins are each rated for a maximum current of 1000 mA.
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 3 of 6
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet
Dimensions
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 4 of 6
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet
Important Notice
Holding the SFP+ connector by its
Do not handle by cable
sides, insert the connector into the
DO NOT Over-bend the cable behind the connector
port on the switch
DO NOT twist the cable
DO NOT kink the cable
DO NOT bend up and down the cable
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 5 of 6
100G QSFP28 Passive Copper Cable OPQS28-T-xx-Px Datasheet
Ordering Information
OP S F P P - T -
01
- P
A
x
Product Code:
Transceiver Type:
Cable Length:
P=Passive;
DAC AWG: For Optech Internal ref.
MSAS= Mini-SAS;
T=Electrical;
X5=0.5M;
A=Active;
A=24;
MSHD=Mini-SAS HD 6~12G;
F=Optical;
01=1M;
B=26;
SFPP=SFP+ 8~10G;
I=Internal Electrical
03=3M;
C=28;
MSFP=Mini SFP;
05=5M;
E=30;
XFP=XFP 10G;
07=7M;
F=32
CX4=CX4 10G;
10=10M;
X=No Media Type (For Loopback)
QDDR=QDDR 20G;
15=15M;
AOC OD:
SF28=SFP28 25G;
20=20M;
K=3.0 mm
QSFP=QSFP 40G;
A0=100M
QFDR=FDR 56G;
xxxx=Customized Length (Unit: CM)
QS28=QSFP28 100G;
For Loopback Attenuation:
CXP=CXP 120G
00=0dB
Part Number
Length (M)
AWG
Voltage
Temperature
OPQS28-T-X5-PE
0.5
30
3.3V
0C to 70 C
OPQS28-T-01-PE
1
30
3.3V
0C to 70 C
OPQS28-T-02-PE
2
30
3.3V
0C to 70 C
OPQS28-T-03-PB
3
26
3.3V
0C to 70 C
OPQS28-T-05-PA
5
24
3.3V
0C to 70 C
Note: All information contained in this document is subject to change without notice.
Optech Technology Co., Ltd. 2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Tel: +886-2-2656-0588 Fax: +886-2-2656-0599 http://www.optech.com.tw e-mail:
[email protected]
Version: 15V.A Page 6 of 6
