10.4” Splash Proof Monitor With Tv Tuner * Specifications

Transcript

TV SYSTEM AND AUDIO MODE OF PRIMARY " /": Show this country has no sound to output the system Other have not listed the country and above catalogs system same also in this machine support scope. 10.4” Splash Proof Monitor with TV Tuner * Specifications 1. Supply voltage 2. Power consumption: 3. Operating temperature: 4. Storage temperature: 5. Monitor screen size 6. Operating system 7. Resolution 8. System DC 12V +/-10% 1A 10% 0 C ~+ 60 C -25 C ~ +70 C 10.4" ( 16:9) TFT active matrix. 800 x 600 dots. NTSC / PAL Dual System View Area 11 PLMRVW105 Table of Contents 1. Table of Contents------------------------------------------------------ 1 2. Warning ---------------------------------------------------------------- 1 3. Package ---------------------------------------------------------------- 2 4.Connection Diagram ---------------------------------------------------2 5.Remote Control ----------------- ---------------------------------------3 6.Appendix--------------- ------------------------------------------------ 4 7.Using the Remote Control----------------- ----------------------------4 8.Monitor Section---------------------------- ----------------------------5 9. OSD Menus in A/V Source --------------------------------------------6 TV SECTION 10. OSD Menus in TV Source ---------------------------------------------7 11. OPERATIONS----------------------------------------------------------8 12.DISPLAY------------------------------------------------------------9~10 13.TV SYSTEM AND AUDIO MODE OF PRIMARY------------------11 14.Specifications---------------------------------------------------------- 11 4.AUTO SEARCH When the indicator is on the AUTO SEARCH, press ENTER on the unit/remote to display this picture and auto full scan channels by pressing ENTER. 5.SEARCH When the indicator is on the SEARCH, press ENTER on the unit/remote to display this picture and auto scan channels by pressing ENTER. 6.FINE TUNE When the indicator is on the FINE TUNE, press ENTER on the unit/remote to display this picture and fine tune by “ / OR V+/V-” button. 7.PROGRAM When the indicator is on the PROGRAM, press ENTER on the unit/remote to display and select the item you want to change by “ / OR V+/V-” button. 8.SKIP When you feel that there are some repeated TV program or image and audio founded not good .You need to skip some program and quick to select. WARN ING This unit is not intended for installation in the front Dr iver / Passenger Compa rtmen t whe re it may be seen by the Dr iver. Installation of this unit in any portion of the vehicle whi ch could impa ir or distract the Dr iver is impr oper and dangerous and assumes No liability wha t so ever for failure to follow the proper installation of this product. To reduce the risk of electric shock, please do not expose this unit to rain, moi sture or open the unit. Da ngerous high voltages are present inside the unit. Our warranty could be voided if you mak e changes or mod ifications not expressly approved by When the indicator is on the SKIP, press ENTER on the unit/remote to display and select the item you want to change by “ / OR V+/V-” button. Press “enter” button to select “ON / OFF’. Remark: Skip function is available only going on choosing the program in sequence by using the program selection of CH-/CH+ . 9.FREQ:Show the TV channel’s Frequency. 1 10 Package DISPLAY 1.MAIN MENU ANT SOURCE TV SYSTEM AUTO SEARCH SEARCH FINE TUNE PROGRAM SKIP FREQ This LCD monitor comes with all the items below. Check to make sure your unit complete. Contact your dealer immediately if anything is missing. * 10.4" TV Monitor X 1 * AC Adapter X 1 * Wall Bracket X 1 * Operation manual Press MENU on the unit/remote to display this picture and adjust the item by “ / OR V+/V-” button. Connection Diagram 2.ANT SOURCE AIR CABLE When the indicator is on the ANT SOURCE, press ENTER on the unit/remote to display this picture and select AIR or CABLE by “ / OR V+/V-” button . When ANT SOURCE is on AIR, this will affect the frequency list in the AUTO SEARCH. 3.TV SYSTEM NTSC FM RADIO SECAM-DK PAL-I PAL-BG DVD Player (Option) DVD Player (Option) AV/IN 1 AV/IN 2 Antenna (Option) +12V AC ADAPTER “F” CONNECTOR When the indicator is on the TV SYSTEM, press ENTER on the unit/remote to display this picture and select NTSC, FM RADIO, SECAM-DK, PAL-I and PAL-BG by “ / OR V+/V-” button . 9 2 Remote Control 1 4 CH+ POWER 5 2 SOURCE 3 ENTER V- MENU V+ 6 OPERATIONS when use TV system in different countries, you must first set the system, then set the signal as antenna or the coaxial of the CATV, AUTO SEARCH. When it is OK, press MENU to return or auto return by tuner to TV picture, then you may enjoy the TV program. CH- 1 2 3 4 5 6 7 8 9 0 MUTE 7 8 1. POWER: Power for ON or OFF 2. SOURCE: Switch input source button (TV, AV input) 3. ENTER: Confirm the selection. 4. CH+/CH-: Adjust channel up / down(For TV only). 5. MENU: A. When source input is TV. Press “MENU” button to enter TV OSD Menu. B.When source input is AV. Press “MENU” button to enter monitor OSD Menu. 6. V+/V-: A. When the OSD menu function is turned off, press the " V+/V- " buttons directly from the remote control to adjust volume. B. Make item selection in OSD menus to increase or decrease parametersas well 7.0-9:Choose number key 8.MUTE:Press the key to close the sound,press it again to resume the sound. . 3 SETUP 1 ANT SOURCE Firstly press MENU to enter Main Menu. Move cursor to “ANT SOURCE” by “ / OR V+/V-” button , and then press ENTER to enter the Menu. The items (AIR/CABLE) can be changed by “ / OR V+/V-” button. The updated parameter will be set up when items changed. And the result be shown immediately. Press MENU back to Main Menu. Press MENU again, you can cancel Main Menu, or Main Menu will be canceled automatically 30 seconds later. SETUP 2 TV System First press MENU to enter Main Menu. Move cursor to “TV SYSTEM” by “ / OR V+/V-” button and then press ENTER to enter the Menu. The items (NTSC/FM RADIO/SECAM-DK/PAL-I/PAL-BG) can be changed by “ / OR V+/V-” button. The updated parameter will be set up when items changed. And the result be shown immediately. Press MENU back to Main Menu. Press MENU again, you can cancel Main Menu, or Main Menu will be canceled automatically 30 seconds later. SETUP 3 AUTO SEARCH Press MENU to enter the Main Menu; and move the cursor to “AUTO SEARCH” by “ / OR V+/V-” button , and press ENTER; then you can enter Sub-Menu and press ENTER according to the cue. During the Channel Scan, the Schedule will displayed in the OSD. If press Enter, the Channel Scan will be stopped. On the right angle demonstrated finally seeks the channel,4 seconds later, it will go back to the TV mode, and the program will stay from the first channel in the guide program searching. Press MENU again, you can cancel Main Menu, or Main Menu will be canceled automatically 30 seconds later. SETUP 4 After returns to the television picture then to depend on the common television operating mode, enjoys the various countries brilliant television program. 8 * TV SECTION Appendix * OSD Menus in TV Source Changing the New Battery in Remote Control 1. Push the battery case button to wards the right. (As shown # 1 in below figure) 2. Pull the battery case away from the remote control.(As shown # 2 in below figure) Change a new battery. AIR CABLE ANT SOURCE TV SYSTEM AUTO SEARCH SEARCH FINE TUNE PROGRAM SKIP FREQ NTSC FM RADIO SECAM-DK PAL-I PAL-BG 2 Battery Cassette Button 1 Using the Remote Control * Quick Adjustment OSD Menus 1. By pressing "MENU" button, you may open the MAIN MENU, using " " or " " buttons to pick out OSD functions. 2. In order to select desire options, it is necessary to press "MENU" again to enter each mode, than using " "/ " " to increase or decrease parameters as well. 3. Press " " or " 1.Point the remote control towards the IR sensor in front of the monitor housing. 2.Operation angle: IR remote control will work about 30 degree in each direction from the IR sensor of the monitor housing. " button directly to adjust speaker volume. VOLUME 50 4. Press the " EXIT" mode to store your selected parameter and leave the OSD Menus. 7 +- 30 Degree 4 Monitor Selection * OSD Menus in A/V Source < MAIN MENU > CONTRAST BRIGHTNESS COLOR SHARPNESS VIDEO SOURCE AUDIO RESET RETURN 1 2 3 4 5 * Quick Adjustment OSD Menus 1.POWER:Power for ON or OFF 1. By pressing "MENU" button, you may open the MAIN MENU, using " " or " 2.MENU: A. When source input is TV. Press “MENU” button to enter TV OSD Menu. B.When source input is AV. Press “MENU” button to enter monitor OSD Menu. 2. In order to select desire options, it is necessary to press "MENU" again to 3. 3. Press " / :A. When the OSD menu function is turned off, press the " V+/V- " buttons directly from the remote control to adjust volume. B. Make item selection in OSD menus to increase or decrease parametersas well 4.SOURCE/ENTER: A. Switch input source button (TV, AV input) B. Confirm the OSD selection. buttons to pick out OSD functions. enter each mode, than using " "/ " " or " " to increase or decrease parameters as well. " button directly to adjust speaker volume. VOLUME 50 4. Press the " EXIT" mode to store your selected parameter and leave the OSD Menus. 5.CH+/CH-: Adjust channel up / down(For TV only). 5 " 6