1.25 Gbps Sfp 1310 Nm, 40km, Transceiver With

Transcript

E x t e n s u s™ 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics PL-XPL-LC-L13-xx The 1G long wavelength, Small Form Factor Pluggable (SFP) transceiver is part of Picolight’s family of E x t e n s u s products designed for single mode applications. With extended reach capability to 40km, the module satisfies a broad range of intermediate to long distance applications. The 1G SFP transceiver features an uncooled Distributed Feedback (DFB), 1310 nm, highspeed edge-emitting laser coupled to a LC optical connector. Its small size allows for high-density board designs that, in turn, enable greater total aggregate bandwidth. The pluggability of the module further allows manufacturers to configure systems later in the build cycle, providing just-in-time inventory and cost control. Key benefits • Compliant with industry-wide physical and optical specifications • High reliability • Enables higher port densities Highlights Applications u Enhanced Digital Diagnostic feature set allows real-time monitoring of transceiver performance and system stability. (Optional Feature) u Module pluggability enables just-in-time (JIT) inventory control of cards, increasing flexibility of port configuration flexibility and reducing operations cost u Host card manufacturing process simplified by moving optical transceiver placement to end of manufacturing line or even to deployment phase u Extended reach of 40km over 9µm/125µm single mode fiber enables increased functionality of equipment beyond standard link distances u Serial ID provides access to customer, vendor and system specific information, providing remote system control and monitoring u All-metal housing provides robust mechanical performance and superior EMI shielding u Signal detect and transmitter fault functions enable system status indicators and debugging • Extended reach • Switch and hub interconnect • Mass storage systems interconnect • Computer cluster cross-connect • Custom high-speed data pipes • Gigabit Ethernet LAN/WAN routers 05000924 Rev 3 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics PL-XPL-LC-L13-xx features • Utilizes a 1310 nm, high reliability, high speed, uncooled DFB laser • Compliant with SFP MSA specifications • Hot pluggable • Compliant with SFF-8472 Digital Diagnostics with External Calibration • Up to 40km on 9µm single mode fiber • Link budget of 18dB • Low power consumption (< 800mW) • 0οC to 70οC operating range • Single +3.3 V power supply • Bit error rate < 1x10-12 • OC transmit disable, loss of signal, and transmitter fault functions • Serial ID functionality • CDRH and IEC 60825-1 Class 1 laser eye safe • FCC Class B compliant • ESD Class 2 per MIL-STD 883 Method 3015 • UL-94 V-0 certified The PL-XPL-LC-L13-xx long wavelength transceiver complies with small form factor pluggable (SFP) multisource agreement (MSA), and satisfies eye safety requirements of CDRH and IEC. The module design allows for excellent latching performance in high-density port configurations. • Internal AC coupling on both transmit and receive data signals • All-metal housing for superior EMI performance Ordering information Temp. Range: Power Supply Tolerance: PL-XPL-LC-L13-11 0 to 70οC +5% PL-XPL-LC-L13-21 0 to 70οC +5% Part Number: Digital Diagnostics: Contact Information: X Picolight Incorporated 1480 Arthur Avenue Louisville, CO 80027 Tel: 303.530.3189 E-mail: [email protected] Web site: www.picolight.com November 2005 Page 2 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Section 1 Functional description The PL-XPL-LC-L13-xx transceiver is designed to transmit and receive 8B/10B encoded serial optical data over 9/125 µm optical fiber. Transmitter The transmitter converts 8B/10B encoded serial PECL electrical data into serial optical data. Transmit data lines (TD+ & TD-) are internally AC coupled with 100 Ω differential termination. An open collector compatible Transmit Disable (TDis) is provided. This pin is internally terminated with a 4.7kΩ − 10kΩ resistor to VccT. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal PIN monitor diode that is used to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. The Transmit Fault signal must be pulled high on the host board for proper operation. A logic “1” output from this pin indicates that a transmitter fault has occurred, or the part is not fully seated and the transmitter is disabled. A logic “0” on this pin indicates normal operation. Receiver The receiver converts 8B/10B encoded serial optical data into serial PECL electrical data. Receive data lines (RD+ & RD-) are internally AC coupled and must be terminated with a 100 Ω differential load. An open collector compatible Loss of Signal is provided. The LOS must be pulled high with a resistor (10 kΩ) on the host board for proper operation. A logic “0” indicates that light has been detected at the input to the receiver. (See Section 3.4, “Optical characteristic”, Loss of Signal Assert/Deassert Level on page 9.) A logic “1” output indicates that insufficient light has been detected for proper operation. Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for optimal performance. Recommended “Application Schematics” are shown in Figure 2 on page 5. 05000924 Rev 3 Page 3 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Figure 1 Block diagram S FP M O D U LE M o n ito r P IN P D H O S T BOARD TD+ LD Lase r D r iv e r 100 Ω TD- Vc cT VccT 4.7 k Ω 4.7k to 10k Ω T X D is a b le A u t o m a t ic P o w e r C o n t r o l C i r c u it T X F a u lt ( A ) T ra n s m it t e r P IN P D RD + P re - A m p . Post A m p. 1 00 Ω RD - VccR 4.7k to 10k Ω LO S ( B ) R e c e iv e r Vcc T D ia g n o s t i c M o n ito r M O D - D E F (0 ) 4.7 k to 10k Ω M O D-D E F (1 ) E EPR OM M O D-D E F (2 ) 100 Ω (C ) E E P R O M November 2005 Page 4 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Section 2 Application schematics Recommended connections to the PL-XPL-LC-L13-xx transceiver are shown in Table 2 below. Figure 2 Recommended application schematic for the PL-XPL-LC-L13-xx transceiver TRANSMIT DATA TD+ 100Ω TD- Vcc VccT 4.7k to 10kΩ 4.7kΩ TX Fault TX Disable RECEIVE DATA RD+ SFP MODULE 100 Ω RD- HOST BOARD Vcc 4.7k to 10kΩ LOS Diagnostic Monitor EEPROM Vcc 4.7k to 10kΩ MOD- DEF (0) MOD- DEF (1) MOD- DEF (2) 50 Ω line FG 05000924 Rev 3 Page 5 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Figure 3 Recommended power supply filtering 1uH VccT 0.1uF 1uH 3.3V VccR 0.1uF 10uF 0.1uF 10uF VeeT VeeR VeeTandVeeRare not internally connected to each other. SFP Module VccTandVccRare not internally connected to each other. Module cover is not internally connected VeeT to andVeeR . Section 3 Technical data Technical data related to the 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics includes: • Section 3.1 Pin function definitions below • Section 3.2 Absolute maximum ratings on page 8 • Section 3.3 Electrical characteristics on page 8 • Section 3.4 Optical characteristic on page 9 • Section 3.5 Link length on page 10 • Section 3.6 Regulatory compliance on page 11 • Section 3.7 PCB layout on page 12 • Section 3.8 Module outline on page 13 November 2005 Page 6 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.1 Pin function definitions Figure 4 Transceiver pin descriptions 1 VeeT 2 TXFault 3 4 Towards Bezel 5 Table 1 Pin Number 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 TX Disable MOD-DEF(2) MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 VeeT RD+ 13 RD- 12 VeeR 11 Towards ASIC LOS 9 VeeR 10 VeeR Transceiver pin descriptions Symbol Name Description Receiver 8 LOS Loss of Signal Out (OC) Sufficient optical signal for potential BER < 1x10-12 = Logic “0” Insufficient optical signal for potential BER < 1x10-12 = Logic “1” This pin is open collector compatible, and should be pulled up to Host Vcc with a 4.7kΩ − 10 kΩ resistor. 9, 10, 11, 14 VeeR Receiver Signal Ground These pins should be connected to signal ground on the host board. 12 RD- Receiver Negative DATA Out (PECL) Light on = Logic “0” Output Receiver DATA output is internally AC coupled 100Ω differential lines and should be terminated with 100Ω differential at the user SERDES. The AC coupling is done internally and therefore isn’t required on host board 13 RD+ Receiver Positive DATA Out (PECL) Light on = Logic “1” Output Receiver DATA output is internally AC coupled 100Ω differential lines and should be terminated with 100Ω differential at the user SERDES. The AC coupling is done internally and therefore isn’t required on host board 15 VccR Receiver Power Supply This pin should be connected to a filtered +3.3V power supply on the host board. See Application schematics on page 5 for filtering suggestions. 7 Rate Rate Select (LVTTL) Not Connected Transmitter 3 TX Disable Transmitter Disable In (LVTTL) Logic “1” Input (or no connection) = Laser off Logic “0” Input = Laser on This pin is internally pulled up to VccT with a 4.7kΩ resistor. 1, 17, 20 VeeT Transmitter Signal Ground These pins should be connected to signal ground on the host board. 2 TX Fault Transmitter Fault Out (OC) Logic “1” Output = Laser Fault occurs when bias current of laser exceeds the factory-calibrated threshold level. Tx_Fault latches high and is cleared upon toggle of Tx_Disable. Logic “0” Output = Normal Operation This pin is open collector compatible, and should be pulled up to Host Vcc with a 4.7kΩ- 10 kΩ resistor. Pull up voltages between 2.0V and VccT+0.3V. Tx_Fault latches high when fault condition occurs 05000924 Rev 3 Page 7 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Table 1 Transceiver pin descriptions (continued) Pin Number Symbol Name Description 16 VccT Transmitter Power Supply This pin should be connected to a filtered +3.3V power supply on the host board. See Application schematics on page 5 for filtering suggestions. 18 TD+ Transmitter Positive DATA In (PECL) Logic “1” Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 Ω resistor internal to the module. 19 TD- Transmitter Negative DATA In (PECL) Logic “0” Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 Ω resistor internal to the module. Module Definition 6, 5, 4 3.2 MOD_DEF (0:2) Module Definition Identifiers Serial ID with optional SFF 8472 Diagnostics (See Annex A) Module Definition pins should be pulled up to Host Vcc with 4.7kΩ - 10 kΩ resistors. Maximum clock rate is 100kHz. Available on PL-XPL-SC-L13-21 Absolute maximum ratings Parameter Symbol Ratings Unit Storage Temperature Tst -40 to +85 °C Operating Ambient Temperature Ta 0 to +70 °C Power Supply Voltage Vcc 0 to +4.0 V Transmitter Differential Input Voltage VD 2.5 VP-P Input Voltage on Mod_def, Tx_Disable Vi VccT+0.3 V Relative Humidity RH 5 to 95 % 3.3 Electrical characteristics (TC = 0°C to 70°C, Vcc = 3.15V to 3.45V unless specified otherwise) Parameter Supply Voltage Symbol Min Typical Max Unit Vcc 3.15 3.3 3.45 V Data Rate Power Consumption 1.25 Pw Gbps 800 mW Notes BER < 1x10-12 Transmitter Data Input Voltage Swing Transmit Disable Voltage Level Transmit Disable/Enable Assert Time Transmit Fault Output Voltage Level November 2005 VTDp-p 300 2400 mVp-p VIH 2.0 Vcc V VIL 0 0.8 V TTD 10 µs TTEN 1 ms VOH 2.0 Vcc + 0.3 V VOL 0 0.8 V Page 8 of 18 Differential, peak to peak Laser output disabled after TTD if input level is V IH; Laser output enabled after T TEN if input level is VIL Transmit fault level is VOH and Laser output disabled TFault after laser fault. 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.3 Electrical characteristics (continued) (TC = 0°C to 70°C, Vcc = 3.15V to 3.45V unless specified otherwise) Parameter Transmit Fault Assert and Reset Times Symbol Typical TFault TReset Initialization Time Min Max Unit 100 µs µs Transmitter fault is VOL and Laser output restored TINI after transmitter disable is asserted for TReset, then disabled. 300 ms After Hot Plug or Vcc ≥ 3.15V 1200 mVp-p 240 ps 20% - 80%, Differential 10 TINI Notes Receiver Data Output Voltage Swing 500 750 Data Output Rise/Fall Time Signal Detect Voltage Level Signal Detect/Loss of Signal Assert Time 3.4 RLOAD = 100 Ω, Differential VOH 2.0 Vcc-0.3 V LOS output level VOL TLOSD VOL 0 0.8 V after light input > LOSD, TLOS 100 µs LOS output level VOH TLOSA TSD 100 µs after light input < LOSA Max Unit Notes 1360 nm 20 dB down 1 nm 0.0 dBm 260 ps Optical characteristic (TC = 0°C to 70°C, Vcc = 3.15V to 3.45V unless specified otherwise) Parameter Symbol Min. Typical Transmitter Wavelength λp Spectral Width ∆λ Average Optical Power PAVG Optical Output Rise/Fall Time trise/fall Extinction Ratio Side Mode Suppression Ratio Total Jitter RIN12 1260 1310 -4.5 ER 9 dB SMSR 30 dB TJ 0.284 UI RIN -120 dB/Hz 1580 nm 20% - 80% 27-1 pattern, TP2, @ 1.25 Gbps, 1 with compliant input signal Receiver Wavelength Average Optical Received Power Loss of Signal Assert/Deassert Level λ 1260 Popt -22.5 0.0 dBm Average @ nominal wavelength, ER=9dB LOSD -29.5 -22.5 dBm Chatter Free Operation LOSA -30.0 -23.0 dBm 0.5 0.6 dB -12 dB Loss of Signal Hysteresis Reflectance 05000924 Rev 3 Ref 1310 -14 Page 9 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.5 Link length (TC = 0°C to 70°C, Vcc = 3.15V to 3.45V unless specified otherwise) Data Rate / Standard Fiber Type 1.25 GBd IEEE 802.3z 1000BASE-LX 9/125µm SMF Modal Bandwidth (MHz*km) Distance Range (km) Notes 40 2 Specification notes 1. UI (Unit Interval): one UI is equal to one bit time. For example, 1.25 Gbps corresponds to a UI of 800ps. 2. This assumes worst cast fiber loss of 0.4dB/km @ 1310nm November 2005 Page 10 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.6 Regulatory compliance The PL-XPL-LC-L13-xx complies with common ESD, EMI, Immunity, and Component recognition requirements and specification (see details in Table 2 on Page 11). ESD, EMI, and Immunity are dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis for design decisions. Table 2 Regulatory Compliance Feature Test Method Performance Laser Eye Safety U.S. 21CFR (J) 1040.10 & 1040.11 IEC 60825-2 1997 CDRH compliant and Class 1 laser safe. Accession # Electrostatic Discharge (ESD) to electrical pins MIL-STD 883C; Method 3015.4 Class 1 (> 1 kV) Electrostatic Discharge (ESD) to optical connector IEC 61000-4-2: 1999 Withstand discharges of 15 kV using a “Human Body Model” probe Electromagnetic Interference (EMI) FCC Part 15 Subpart J Class B CISPR 22: 1997 EN 55022: 1998 Class B VCCI Class I Noise frequency range: 30 MHz to 10 GHz. Good system EMI design practice required to achieve Class B margins. Immunity IEC 61000-4-3: 1998 Field strength of 3 V/m RMS, from 10 MHz to 1 GHz. No effect on transceiver performance is detectable between these limits. Component UL 1950 CSA C22.2 #950 IEC 60950: 1999 UL File # CSA File # TUV Certificate # 05000924 Rev 3 Page 11 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.7 PCB layout Figure 5 Board layout Figure 6 Detail layout November 2005 Page 12 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 3.8 Module outline Figure 7 Section 4 Related information Other information related to the 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics includes: 4.1 • Section 4.1 Digital Diagnostic Monitoring and Serial ID Operation below • Section 4.2 Package and handling instructions below • Section 4.3 ESD discharge (ESD) on page 18 • Section 4.4 Eye safety on page 18 Digital Diagnostic Monitoring and Serial ID Operation The PL-XPL-LC-L13-xx is equipped with a 2-wire serial EEPROM that is used to store specific information about the type/identification of the transceiver as well as optional real-time digitized information relating to the transceiver’s performance (PL-XPL-xx-L1x-2x part numbers). See Section IV, “Module Definition Interface and Data Field Description” of the SFP-MSA Pin Definitions and Host Board Layout document for memory/address organization of the identification data and the Small Form 05000924 Rev 3 Page 13 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Factor Commitee’s document number SFF-8472 Rev 9.5, dated June 1, 2004 for memory/address organization of the digital diagnostic data. The optional enhanced digital diagnostics feature monitors five key transceiver parameters which are Externally Calibrated and should be read as 2’s complement Analog to Digital Values and interpreted as follows using the external calibration constants in bytes A2h (56-91) and the Analog to Digital (AD) values in bytes A2h (96-105); see Table 5 for address descriptions. Transceiver Temperature in degrees Celsius: Internally measured as junction temperature of monitoring IC. Represented as a 16 bit signed two’s complement value in increments of 1/256 degrees Celsius from -40 to +125°C with LSB equal to 1/256 degrees C. Accuracy is ± 3 degrees Celsius over the specified operating temperature and voltage range. T = Tslope*TAD + Toffset Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16 bit unsigned integer with the voltage defined as the full 16 bit value (0-65535) with LSB equal to 100µV with a measurement range of 0 to +6.55V. Accuracy is ± 3% of nominal value over the specified operating temperature and voltage ranges. V= Vslope*VAD + Voffset TX Bias Current in µΑ: Represented as a 16 bit unsigned integer with current defined as the full 16 bit value(0-65535) with LSB equal to 2µΑ with a measurement range of 0 - 131mA. Accuracy is ± 10% of nominal value over the specified operating temperature and voltage ranges. I=Islope*IAD + Ioffset TX Output Power in mW: Represented as a 16 bit unsigned integer with the power defined as the full 16 bit value (0-65535) with LSB equal to 0.1µW. Accuracy is ± 3dB over the specified temperature and voltage ranges over the permitted range of 100µW to 800µW ( -4.5dBm to 0dBm). Data is not valid when transmitter is disabled. TP=TPslope*TPAD + TPoffset RX Received Optical Power in mW: Represented as OMA as a 16 bit unsigned integer with the power defined as the full 16 bit value(0-65535) with LSB equal to 0.1µW. Accuracy is ± 3dB over the specified temperature and voltage ranges over the permitted power range of 15µW to 1000µW (– 22.5dBm to 0dBm). RP=RP4*RPAD4+ RP3*RPAD3+ RP2*RPAD42+ RP1*RPAD1+ RP0*RPAD0 Reading the data The information is accessed through the MOD_DEF(1), and MOD_DEF(2) connector pins of the module. The specification for this EEPROM (ATMEL AT24CO1A family) contains all the timing and addressing information required for accessing the data. The device address used to read the Serial ID data is 1010000X(A0h), available on all SFP part numbers, and the address to read the diagnostic data is 1010001X(A2h), on PL-XPL-xx-L1x-2x part numbers. Any other device addresses will be ignored. Refer to Table 3, Table 4, and Table 5 for information regarding addresses and data field descriptions MOD_DEF(0), pin 6 on the PL-XPL-LC-L13-xx transceiver, is connected to Logic 0 (Ground) on the transceiver. MOD_DEF(1), pin 5 on the PL-XPL-LC-L13-xx transceiver, is connected to the SCL pin of the EEPROM. November 2005 Page 14 of 18 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics MOD_DEF(2), pin 4 on the PL-XPL-LC-L13-xx module, is connected to the SDA pin of the EEPROM. The EEPROM WP pin is internally tied to ground with no external access, allowing write access to the customer-writable field (bytes 128-247 of address 1010001X). Note: address bytes 0-127 are not write protected and may cause diagnostic malfunctions if written over. Decoding the data The information stored in the EEPROM including organization is defined in the Small Form-Factor Pluggable Multisource (SFP-MSA) Pin Definitions and Host Board Layout document, dated 3/13/00, Section IV. The digital diagnostic information stored in the EEPROM is defined in the Small FormFactor document SFF-8472 draft rev 9.5, dated June 1, 2004. Table 3 Data Field Descriptions Address( 1010000X)(A0h) 0 Serial ID Information; Defined by SFP MSA 95 Picolight Specific Information 127 Address( 1010001X)(A2h) 0 Alarm and Warning Limits 55 Reserved for External Calibration Constants 95 Real Time Diagnostic Information 119 Picolight Specific Information 127 Non-volatile, customerwriteable, field-writeable area Reserved for SFP MSA 247 Picolight Specific Information 255 05000924 Rev 3 255 Page 15 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Table 4 Serial ID Data and Map Address 0 1 2 3 11 12 13 14 15 16 17 18 19 20 36 37 40 56 60 62 63 64 65 66 67 68 84 92 93 94 95 96 November 2005 Length 1 1 1 8 1 1 1 1 1 1 1 1 1 16 1 3 16 4 2 1 1 1 1 1 1 16 8 1 1 1 1 32 Name Identifer Ext. ID Connector TRx Code Encoding BR Nominal Reserved 9um-km Length 9um Length 50um Length 62.5um Length Cu Length Reserved Vendor Name Reserved Vendor OUI Vendor PN Vendor Rev Laser WL Reserved CC_BASE Reserved Option Value BR max BR min ASCII ASCII Diag. Mon. Enh. Features Diag? CC_EXT ASCII PL-XPL-LC-L13-11 PL-XPL-LC-L13-21 Value Value 3 3 4 4 7 7 0000000200000000 0000000200000000 1 1 0D 0D 0 0 28 28 FF FF 37 37 37 37 0 0 0 0 PICOLIGHT PICOLIGHT 0 0 0485 0485 PL-XPL-LC-L13-11 PL-XPL-LC-L13-21 Page 16 of 18 051E 0 00_63 0 1A 0 0 Vendor SN Date Code 80 0 0 64_95 Read-Only 051E 0 00_63 0 1A 0 0 Vendor SN Date Code 58 B0 1 64_95 Read-Only 05000924 Rev 3 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics Table 5 Diagnostic Data Map Address (1010001X)(A2h) Memory Address Value 00-01 Temp High Alarm 02-03 Temp Low Alarm 04-05 Temp High Warning 06-07 Temp Low Warning 08-09 Voltage High Alarm 10-11 Voltage Low Alarm 12-13 Voltage High Warning 14-15 Voltage Low Warning 16-17 Bias High Alarm 18-19 Bias Low Alarm 20-21 Bias High Warning 22-23 Bias Low Warning 24-25 TX Power High Alarm 26-27 TX Power Low Alarm 28-29 TX Power High Warning 30-31 Tx Power Low Warning 32-33 RX Power High Alarm 34-35 RX Power Low Alarm 36-37 RX Power High Warning 38-39 RX Power Low Warning 40-55 Reserved 56-59 RP4 60-63 RP3 64-67 RP2 68-71 RP1 72-75 RP0 76-77 Islope 78-79 Ioffset 80-81 TPslope 82-83 TPoffset 84-85 Tslope 86-87 Toffset 88-89 Vslope 90-91 Voffset 92-94 Reserved 95 Checksum 90-91 External Calibration Constant 92-94 Reserved 95 Checksum 96 Temperature MSB 97 Temperature LSB 98 Vcc MSB 99 Vcc LSB 100 TX Bias MSB 101 TX Bias LSB 102 TX Power MSB 103 TX Power LSB 104 RX Power MSB 105 RX Power LSB 106 Reserved MSB 107 Reserved LSB 108 Reserved MSB 109 Reserved LSB 110 Optional Status/Control Bits 111 Reserved 112-119 Optional alarm & warning flag bits 120-127 Vendor specific 128-247 User/Customer EEPROM 248-255 Vendor specific 05000924 Rev 3 Comments MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address For future monitoring quantities External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant Reserved 0_95 Refer to SFF-8472 rev 9.3 Reserved Low order 8 bits of sum from 0-94 Internal temperature AD values Internally measured supply voltage AD values TX Bias Current AD values Measured TX output power AD values Measured RX input power AD values For 1st future definition of digitized analog input For 2nd future definition of digitized analog input Refer to SFF-8472 rev 9.3 Reserved Refer to SFF-8472 rev 9.3 Vendor specific Field writeable EEPROM Vendor specific Page 17 of 18 November 2005 1.25 Gbps SFP 1310 nm, 40km, Transceiver with Digital Diagnostics 4.2 Package and handling instructions Process plug The PL-XPL-LC-L13-xx is supplied with a dust cover. This plug protects the transceiver’s optics during standard manufacturing processes by preventing contamination from air borne particles. Note: It is recommended that the dust cover remain in the transceiver whenever an optical fiber connector is not inserted. Recommended cleaning and de-greasing chemicals Picolight recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning. Do not use halogenated hydrocarbons (e.g. trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol, N-methylpyrolldone). Flammability The PL-XPL-LC-L13-xx housing is made of plastic and sheetmetal. 4.3 ESD discharge (ESD) Handling Normal ESD precautions are required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from packaging and handled only in an ESD protected environment utilizing standard grounded benches, floor mats, and wrist straps. Test and operation In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly installed in the system, this transceiver should meet and exceed common ESD testing practices and fulfill system ESD requirements. Typical of optical transceivers, this module’s receiver contains a highly sensitive optical detector and amplifier which may become temporarily saturated during an ESD strike. This could result in a short burst of bit errors. Such an event might require that the application re-acquire synchronization at the higher layers (e.g. Serializer/Deserializer chip). 4.4 Eye safety The PL-XPL-LC-L13-xx is an international Class 1 laser product per IEC 825-2: 1997, and per CDRH, 21 CFR 1040 Laser Safety Requirements. The PL-XPL-LC-L13-xx is an eye safe device when operated within the limits of this specification. Operating this product in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure. CAUTION! Tampering with this laser based product or operating this product outside the limits of this specification may be considered an act of “manufacturing,” and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (21 CFR 1040). November 2005 Page 18 of 18 05000924 Rev 3