Transcript
GENERAC The Reliable Ones
1300PSI Owner’s Manual
Problems? Questions?
Before taking your unit back to the store, call the pressure washer helpline at
1-800-270-1408 M-F 8-5 CST
Model No. 12800 (1300 PSI High Pressure Washer) Manual No. B3719 Revision 0 (1/27/99) This symbol points out important safety instructions, which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in the manual before attempting to operate this unit.
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
Important! Safety Instructions Important! Save these instructions
CAUTION! Read all instructions before using
Follow the maintenance instructions specified in the manual.
this product to reduce the risk of injury.
Inspect cord before every use. Do not use if cord is damaged.
This product shall only be connected to a power supply receptacle protected by a Ground Fault Circuit Interrupter (GFCI). This is done to comply with National Electrical Code (NFPA 70) and to provide additional protection from risk of electrical shock.
Keep all connections dry and off the ground.
Save these instructions.
Do not touch plug with wet hands.
Operate this pressure washer only in areas away from combustible materials, combustible fumes or dust.
DANGER! Risk of electrocution!
Doubleinsulated When servicing, use only identical replacement parts.
Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury.
This product shall only be connected to a power supply receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Read instruction manual before using.
Do not allow CHILDREN to operate the Pressure Washer at any time.
WARNING! To reduce the risk of injury, close
supervision is necessary when product is used near children. Know how to stop the product and bleed the pressure quickly. Be thoroughly familiar with controls.
Before starting the Pressure Washer in cold weather, check all parts of the equipment and be sure ice has not formed. Units with broken or missing parts, or without protective housing or covers should NEVER be operated.
Stay alert. Watch what you are doing. Do not operate the product when fatigued or under the influence of alcohol or drugs.
DANGER! Risk of Explosion Do not spray flammable liquids.
Keep operating area clear of all persons.
Never aim the gun at people, animals or plants.
WARNING! Risk of injury or injection to
persons Do not discharge stream at persons or animals. High pressure hose can develop leaks from wear, kinking, abuse, etc. Water spraying from a leak is capable of injecting material into skin. Do not point the pressure washer spray at people or animals.
For household use. For indoor or outdoor use. High pressure stream of fluid that this equipment can produce may pierce skin and its underlying tissues, leading to serious injury and possible amputation. High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds.
Do not overreach or stand on unstable support. Keep good footing and balance at all times.
2
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
Important! Safety Instructions Important! Save these instructions
Always wear eye protection when you use this equipment or when you are in vicinity where the equipment is in use.
Store in a clean, dry area. Ideally, the unit should be stored in a frostfree room.
Servicing of a Double Insulated Product.
Never move the machine by pulling on high pressure hose. Use the handle provided on the top of the unit.
In a doubleinsulated product, two systems of insulation are provided instead of grounding. No means of grounding is provided on a doubleinsulated product, nor should a means for grounding be added.
Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
Servicing a doubleinsulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a doubleinsulated product must be identical to the parts they replace. Use only genuine replacement parts. A doubleinsulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED.
High pressure spray may damage fragile items including glass. Do not point spray gun at glass when in the high pressure mode. Keep the hose connected to machine or the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous.
The symbol
Hold the spray gun firmly in your hand before you start the unit. Do not leave the pressure washer unattended while the machine is turned on.
may also be marked on the product.
Extension Cords Use only extension cords that are approved for outside use. These extension cords are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT IN USE. Use only extension cords having an electrical rating greater than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect it. Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the pressure washer from the extension cord.
Cleaning area should have adequate slopes and drainage to reduce possibility of a fall due to slippery surfaces. Keep water spray away from electric wiring or fatal electric shock may result. Do not bypass any safety device on this machine. Operate and store this unit on a stable surface. Inspect hose each time before using it. Check all hoses for cuts, leaks, abrasions, bulging of cover, damage or movement of couplings. If any of these conditions exist, replace hose immediately. Never repair high pressure hose. Replace it with another hose that meets minimum pressure rating of your pressure washer.
3
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
CONGRATULATIONS on your purchase of a GENERAC electric high pressure washer. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
PRODUCT SPECIFICATIONS
Should you experience any problem you cannot easily remedy, please contact your nearest GENERAC Authorized Service facility, or call 18002701408. We have competent, welltrained technicians and the proper tools to service or repair this unit.
Pressure Washer Specifications Pressure
1300 pounds per square inch (PSI)
Flow Rate
1.5 gallons per minute (GPM)
Please read and retain this manual. The instructions will enable you to assemble and maintain your high pressure washer properly. Always observe the SAFETY INSTRUCTIONS.
Detergent Mix
Use Undiluted Detergent
Water Supply Temperature
Inlet water not to exceed 104°F
CUSTOMER RESPONSIBILITIES
Motor
Brush Type (Universal)
Rated Voltage
120 Volts
Current
14 Amperes
Read these instructions and Operators Manual in its entirety before you attempt to assemble or operate your new high pressure washer. Your high pressure washer has, for the most part, been assembled at the factory. Before you can operate your new high pressure washer, you must properly connect the high pressure hose and the water supply.
Read and observe the safety rules. Follow regular schedule in maintaining, caring for and using your high pressure washer. Follow the instructions under Maintenance and Storage sections of this Owner's Manual. Model Number
If you have any problems with the assembly of your pressure washer, please call the pressure washer helpline at 18002701408.
12800
Serial Number_________________________________ Date of Purchase________________________________ The model and serial numbers will be found on a decal attached to the pressure washer. Record both serial number and date of purchase and keep in a safe place for future reference
4
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
KNOW YOUR PRESSURE WASHER Read this owners manual and safety rules before operating your high pressure washer. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Spray Gun Grip Start System
Goggles
Master On/Off Switch Water Inlet
High Pressure Hose
Foamer
High Pressure Outlet
Turbo Nozzle and Extension
Foamer Used to apply detergent. Mixes water and detergent in outlet water flow. Garden Hose Connector (Not Shown) Allows rapid connection of your garden hose to the water inlet.
High Pressure Outlet Connection for high pressure hose. Master On/Off Switch This switch ONLY enables the Grip Start system to function. Spray Gun Controls the application of water onto cleaning surface with trigger device. Includes safety latch. Turbo Nozzle and Extension Attaches to the spray gun and allows you to clean or rinse surfaces at high pressure. You cannot apply detergent using the turbo nozzle. Water Inlet Connection for garden hose.
Goggles Always wear eye protection when operating your pressure washer. Grip Start System Pressing and releasing the spray gun trigger starts and stops the electric motor in the pressure washer. High Pressure Hose Connect ends to spray gun and high pressure outlet.
5
Th eR el ia bl eO ne s
G E N E R
A C
Generac 1300PSI High Pressure Washer
CARTON CONTENTS
Figure 2 Attach High Pressure Hose to Main Unit.
Items in the carton include: Main Unit Parts Box (which includes the following): Goggles Owners Manual Spray Gun Turbo Nozzle and Extension Foamer High Pressure Hose Garden Hose Connector Refer to the above list for an illustrated listing of all items included with your pressure washer. Become familiar with each piece before assembling the pressure washer. Check all contents against list. If any parts are missing, call the pressure washer helpline at 18002701408.
Check the screen on the garden hose connector. Make sure it is clean and check for damage. If you see any damage in the screen, do not use (Figure 3). Figure 3 Install Garden Hose Connector and Attach Garden Hose.
HOW TO SET UP YOUR PRESSURE WASHER
Check inlet screen. Connect garden hose here.
Unwind the high pressure hose and attach it to spray gun (Figure 1). Figure 1 Attach High Pressure Hose to Spray Gun. Connect high pressure hose here
Attach the garden hose connector to the pressure washer. Attach garden hose to the pressure washer. Attach the high pressure hose to the high pressure outlet and tighten by hand (Figure 2).
DANGER! When connecting the unit to a power supply receptacle, use ONLY a receptacle protected by a Ground Fault Circuit Interrupter (GFCI). This will help protect against electrical shock.
6
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
CAUTION! Before starting you should be
Press the master On/Off Switch to the On position (Figure 5).
sure the electrical supply is rated at 120 volts, 15 amps.
Figure 5 Press the Master On/Off Switch to the On Position.
WARNING! To reduce the risk of
electrocution, keep ALL connections dry and off the ground. DO NOT touch plug with wet hands. Note: We do not recommend that you use extension cords with this pressure washer. If, however, your application requires that you need an extension cord, use only extension cords that are approved for outside use. These extension cords are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT IN USE. Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords.
WARNING! Before starting the pressure washer, be sure you are wearing adequate eye protection. Goggles are included with this unit.
DANGER! You must attach the spray gun
WARNING! Gun kicks back. Use both
and all hoses before you start the motor.
hands.
Turn on the water. NOTE: Inlet water temperature should not exceed 104°F.
DANGER! Risk of injury or injection to
people and animals. DO NOT discharge stream at people or animals. Squeeze trigger to produce spray.
DANGER! You must be careful at this point. Anytime you squeeze the trigger, the motor will start and water will spray out of the gun. Squeeze trigger to purge pump of system air and impurities.
NOTE: Behind the trigger to the gun is a SAFETY LATCH. You can place this latch as shown (Figure 6) to keep the washer from accidentally spraying while you are changing the nozzle head or foamer or performing other tasks.
Attach the turbo nozzle extension to spray gun by aligning the locking tabs on the extension with the grooves in the gun. Push extension inward and twist clockwise to lock in place (Figure 4).
Figure 6 Apply the Safety Latch.
Figure 4 Connect the Turbo Nozzle Extension to the Spray Gun.
7
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
STOPPING YOUR PRESSURE WASHER
CAUTION! The turbo nozzle produces an
extremely high pressure spray which is capable of removing paint and cutting holes through surfaces if held too close. Always make sure the surface you will clean will not be damaged by the high pressure spray by testing in a hidden area.
If the pressure washer is running, release the trigger.
DANGER! Releasing the trigger will shut off the motor but does not shut off the unit. You must also place the Master On/Off Switch to the OFF position. Place Master On/Off switch in Off position. Simply shutting OFF motor will not release pressure in the system. Squeeze the trigger on the gun to relieve the pressure in the hose.
Note: You cannot apply detergent with the turbo nozzle.
Applying Detergent With Foamer IMPORTANT: Use soaps designed specifically for pressure washers. Household detergents could damage the pump. NOTE: Never use garden hose inlet to siphon detergent or wax.
DANGER: Never leave your pressure washer unattended even when turned off.
DANGER: You MUST attach all hoses and the spray gun before you start the motor.
HOW TO USE YOUR WASHER
WARNING! Before removing any spray gun
extension, be sure to turn off the pressure washer and relieve pressure by pressing the trigger. You could be injured if you try to remove an extension if the pressure washer is running and there is pressure in the system. Pressure washers are useful cleaning tools designed to clean almost any surface in two easy steps.
You now should know how to START your pressure washer and how to STOP it. The information in this section will tell you how to adjust the spray pattern and apply detergent or any other cleaning chemicals.
First, apply an appropriate detergent/solvent solution to penetrate and loosen grime. Apply detergent at low pressure to avoid splashing, overspraying and waste. Leave the solution on surface for 3 to 5 minutes to allow solution to work. Reapply as necessary to keep solution from drying.
How to Use the Turbo Nozzle The turbo nozzle rotates the high pressure stream in a rapid circular pattern. The high pressure spray is most effective when the tip of the wand is held between 8 to 24 inches from the surface being cleaned.
The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean.
Always start the turbo nozzle at a distance, gradually getting closer to the surface until you get the cleaning force you want.
8
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
Figure 9 Connecting the Foamer.
To apply detergent follow these steps: Detach the turbo nozzle extension from the spray gun.
To rinse, YOU MUST, stop the pressure washer, remove the foamer and connect the adjustable nozzle extension. Note Detergents are most effective applied to a dry surface.
Remove the bottle from the foamer. Align the locking tabs on the foamer with the groves in the gun. Push inward and twist clockwise to lock in place. (Note: make sure that when you lock the foamer into place you have the hose that connects to the foamer bottle hanging downward.)
To Clean Start at lower portion of area to be washed and work upward, using long, even overlapping strokes. Detergent or degreaser works best when you apply it to a dry surface first. Let it set for 35 minutes before washing and rinsing.
Prepare your detergent solution as required by the manufacturer and fill bottle with the solution. Attach bottle back onto foamer making sure the bottle hangs down.
Rinse
Start washer and apply detergent to a dry surface, starting from the bottom and working up.
Start at the top of area to be rinsed, working down with the same action as for cleaning.
9
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
CUSTOMER RESPONSIBILITIES AND MAINTENANCE
PURGE PUMP OF AIR AND CONTAMINANTS To remove the air from the pump, follow these steps: Set up the pressure washer as described in the ASSEMBLY section and connect the water supply.
The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual.
Remove the turbo nozzle extension from the gun. Pull the trigger on the gun and hold.
BEFORE EACH USE
To remove the contaminant from the pump, follow these steps: Set up the pressure washer as described in the ASSEMBLY section, connect the water supply and start the pressure washer according to instructions in the OPERATION section.
Check and Clean Inlet Screen Remove garden hose connector and examine the inlet screen. Clean if clogged or replace the inlet screen if damaged.
Remove the turbo nozzle extension from the gun.
Check High Pressure Hose
Pull the trigger on the gun and hold. When the water supply is steady and constant, you may refasten the turbo nozzle extension and use pressure washer normally.
DANGER: Water spraying from a leak is
capable of injecting material into skin. Inspect hose each time before using it. Never repair high pressure hose. Replace it with another hose that meets minimum pressure rating of your pressure washer. High pressure hose can develop leaks from wear, kinking, and abuse. Check all hoses for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings. If any of these conditions exist, replace hose immediately.
PREPARING THE UNIT FOR STORAGE Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and freeze pump action. If you do not plan to use the Pressure Washer for more than 30 days, follow this procedure:
Check Gun and Wand
1. Shut off the pressure washer, unplug it and let it cool, then remove all hoses.
Examine hose connection and make sure it is secure. Test trigger by pressing it and making sure it springs back into place when released. Put safety latch in ON position and test trigger. You should not be able to press trigger.
2. Store the pressure washer and its components in such a way as to protect it from freezing. 5. Store in a clean, dry area. Ideally, the unit should be stored in a frostfree room. 6. Coil the high pressure hose and inspect it for damage. Cuts in the hose or fraying of it could result in leaks and loss of pressure. Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose. Replace the hose with the genuine Generac part. 7. Drain water from hose and properly store it to prevent cuts and general wear.
10
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
Troubleshooting Points Problem Pressure washer will not start.
Pressure washer does not come up to pressure.
Cause
Correction
1. No electrical power is available.
1. Check cord, plug power, socket, electrical supply and circuit breaker/fuse.
2. Motor overheats.
2. Turn off the unit. Press trigger of gun to relieve pressure on the unit. Allow unit to cool for about 2 min. It should run when you turn it ON again.
3. Low voltage.
3. Contact Generac service facility.
4. Trigger not open.
4. Open trigger.
5. Electrical defect.
5. Contact Generac service facility.
1. Pump is sucking air.
1. Water hose must be 1/2inch or greater in diameter. Be sure water supply is ON. Be sure water supply is clean. Check all connections for leaks or blockage. Turn OFF the unit, hold trigger in OPEN position to relieve pressure and allow air in line to escape. With trigger still in OPEN position turn ON the unit. Repeat if necessary.
High pressure spray is irregular.
2. Water inlet is clogged.
2. Clean water inlet screen.
3. Pump not bled to remove air.
3. Switch OFF washer, press trigger, switch ON washer while pressing trigger. Repeat if necessary.
4. Pump is faulty.
4. Contact Generac service facility.
1. Water supply is inadequate.
1. Turn ON water to full position.
11
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
Drawing No. B3653
Exploded View Pump and Motor
12
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
Parts List Pump and Motor Item 1 2 3
Part # B1514 40945 97835
Qty 1 3 1
4
20610
2
5
97822
1
6 7
B2663 97826
1 1
8
97824A
1
9
97825
1
10 11 12 13 14
97833 97830 97832 99503 A1495
1 3 3 3 2
15 16 17 18 19 20 21 22
21055 28739A 20138 20928 B3660 B3568 21126 21125
1 1 1 1 1 1 1 1
23
20217
1
Description ASSY, Motor Complete BOLT, SHCS M6-1.0 x 20mm O RING, Hsg Seal, dia. 82.2 x 2.62mm WASHER, Brg dia. 35 x 55 x 3mm BEARING, Ndle Thrust dia. 35 x 52mm ASSY., Cam/Gear WASHER, Brg dia. 40 x 60 x 1mm BEARING, Needle dia. 40 x 60mm WASHER, Brg dia. 36 x 60 x 6mm SHAFT, Idler Axial Cam RETAINER, Piston Spring PISTON, dia. 15 x 65mm SPRING, Piston Return TAPTITE, M4-0.7x10mm SW MTG GROMMET, Rubber TIE, Wrap SWITCH, Auto HOUSING, Auto-Switch SPRING, P.A.S.S. PISTON ASSY, P.A.S.S. RING, Backup dia. 26.0 ID O RING dia. 25.07 ID x 2.62 CS [.103"] STOP, Piston Return
13
Item Part # 24 21124
Qty 1
25 26
20218 21123
1 1
27 28 29 30 31 32 33 34 37 38
B1124 97855 97100 B3570 93680 97831 97929 B3569 97841 97840
1 1 1 1 3 3 1 1 3 3
39
B1449
6
40
97934
7
41 42 43 44 45 46 48 49 50
76353A 97852 B2240 A1130 B1960 40946 B3571 93667 B2020
1 1 1 1 1 4 1 3 1
Description RING, Backup dia. 4.34 Id x 1.24 CAP, Retainer O RING dia. 3.68 Id x 1.78 CS [.070"] CAP, Inlet O RING, dia. 6.5 x 2.01mm CAP, High Pressure HOUSING, Piston SEAL, Oil-piston dia. 15 TC4 SPACER, Pilot SPRING, Check Valve VALVE, Shuttle CAP, Check Valve O RING, Hi-press dia. 15.6 x 1.78mm ASSY., Check Valve O RING, Chk Valve dia. 12.4 x .78mm PLUG, Taper dia. 5.4 BALL, dia. 3/16" Pop-off Valve SCREW, Lock Socket SPRING, Pop-off Valve SEAT, Ball BOLT, SHCS M6- 1.0 x 35mm PUMP, Head SEAL, Piston U Cup O-RING, 3.68 I.D. x 1.78 CS ELF
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
Drawing No. B3720
Exploded View Main Unit
14
R EOnes Nble Eelia GThe R
Generac 1300PSI High Pressure Washer
C A
Parts List Main Unit Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Part # N/A B1415 A1252 B2525 20566 98806 97893 20984 98801 B1566 20985 20986 84543B 98805 84358 B1866 B1053 NSP NSP 21334 21335 21424 B1236D A1484 A1485 97835 99350 21336 21337 B3337 B1300D A1069 87815
Qty 1 1 1 1 1 1 1 1 4 1 1 1 2 1 4 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1
Description ASSY., Motor and Pump (see pump exploded view) DECAL, Circuit DECAL, Unit DECAL, Instructions DECAL, 1-800 # FOAM, Air In, Fan-end HOUSING, Switch and Cord SWITCH, Rocker 16A MOUNT, Rubber COVER, Motor ENCLOSURE, Rocker Switch Boot BOOT, Rocker Switch SCREW, 3.5mm x 12mm Plastite CORD, Power SCREW, #6-19 x .75 mm Plastite DECAL, Gun Warning DECAL, ETL DECAL, Data OVERLAMINATE HOUSING, Inlet HOUSING, Outlet CONNECTOR, Garden Hose NOZZLE, 1.15mm dia. (Lilac) NUT, Strain Relief Lock SEAL RING, Strain Relief O RING, Hsg Seal, dia. 82.2 x 2.62mm SCREW, #6 Plastite GUN, Spray WAND, Extension HOSE, High Pressure NOZZLE, Head FOAMER GOGGLES
15
A C Th eR el ia bl eO ne s
G E N E R
Generac 1300PSI High Pressure Washer
Limited Pressure Washer Warranties (includes Master Contractor) Generac Portable Products warrants to the original retail purchaser, the pressure washer manufactured by Generac Portable Products to be free from defects in material and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term original purchaser means the person for whom the pressure washer is originally purchased.
Warranty Schedules Electric Power Washer All Other Engine-driven
1 year (does not apply to commercial or rental applications) Engine:
CONSUMER* Warranted solely by Engine Manufacturer
COMMERCIAL* Warranted solely by Engine Manufacturer
Pump:
1 year
90 days
* NOTE: For the purpose of this warranty consumer use means personal residential household use by original purchaser. Commercial Use means all other uses, including rental, construction, commercial and income producing purposes. Once a pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for the purposes of this warranty. During said warranty period, Generac Portable Products will, at its option, repair or replace any part which, upon examination by Generac Portable Products or Generac Portable Products Authorized Dealers, is found to be defective under normal use and service**. All transportation costs under warranty, including return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser. ** NORMAL WEAR: As with all mechanical devices, pressure washers need periodic parts service and replacement to perform well. This warranty will not cover repair when normal use has exhausted the life of a part or pressure washer pump. THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES, WANDS, NOZZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc. Pumps which have been run without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freezing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.). THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, Generac Portable Products MAKES NO OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The duration of any implied warranties which cannot be disclaimed is limited to the time period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF Generac Portable Products' NEGLIGENCE. Generac also disclaims any responsibility for incidental or consequential damages such as the loss of time or the use of the power equipment, or any commercial loss due to the failure of the equipment: and any implied warranties are limited to the duration of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. For service, see your nearest Generac Portable Products authorized warranty service facility or call 1-877-544-0982. Warranty service can be performed only by a Generac Portable Products authorized service facility. This warranty will not apply to service at any other facility. At the time of requesting warranty service, evidence of original purchase date must be presented.
