Transcript
Side 2
8
9
Install Hard Drives/Carriers Remove the drive carrier by pressing the green button and opening the lever.
B
Slide the carrier away from the chassis.
C
Remove the air baffle and save for future use. B TA ING FF UT IVE K O MO DR EA E D BR FOR HAR BE 5´´ 2.
A
E F
Install and Cable Optical Device (optional)
A B
With the lever open, insert the hard disk drive assembly into the chassis opening and push until the locking lever engages. Push in the lever to lock it into place.
Remove the Filler Panel.
Install the plastic latch on the rear side of the drive and fix it with two screws.
D
Pull the power and data cables through the front of the chassis opening.
E
Connect the cables as shown.
P TO E
Insert optical device assembly into front panel opening and push all the way until it stops .
E a
iew l ar V ica Re of Opt rive D
B
F
F
l ica Opt Drive
A C
B
C
Remove the security screws.
C
Dat
er
Pow
D F
DD
Note: Hard drive 3 location is shown above.
D
10 C
A
CAUTION: To maintain proper system cooling, a filler blank must be installed if you do not install a device at this location.
CAUTION: If you install less than three drives or devices, empty drive bays must be occupied by carriers with baffles to maintain proper system cooling.
12
Install PCIe Add-in Card RiserAssembly
C
card slot. Insert add-in card until it seats in the riser connector. Secure add-in card with screw as shown.
dd-in
D
11
Install PCIe Add-in Card
A Remove filler panel from the add-in B
Attach the hard drive to the carrier with four screws as shown.
OVE
Fille
nel
A
13
Install Processor Air Duct
NOTE: Use care to
with the server board riser socket.
r Pa
IMPORTANT NOTE: Refer to the Cabling Diagram below for connection locations and cable routing.
Install processor air duct as shown.
A Align the riser assembly
REM
al y tic Tra Op ice bly v m De sse A
´H 5´ 3.
A
avoid pinching system cables.
14
Install the Top Cover
A
Place cover onto chassis and slide forward to engage recessed edge at front of cover. Make sure the latch is locked.
B
Tighten the four screws.
Install Rack Handles
B Press the riser
assembly into place and secure with the screw.
Card
A
A
Riser Card Connector
Recessed Edge
B
A
B
Riser Connector
B
PCI Riser Socket
CAUTION: Observe normal ESD precautions when installing add-in cards.
controller.
Network Network PCI-E Card
A. B. C. D. E. F.
D. Install Operating System Drivers: With the operating system running, insert the Intel® Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel® Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other operating systems, browse the CD folders to locate and install the driver files.
B
C D E F G
CPU
N
Note: Refer to the Technical Product Specification for Diagnostic LED decoder list.
Enabled
Serial B
A complete list of accessories and spares can be found at: http://www.intel.com/support/motherboards/server
Front Panel Connector CMOS Clear
2
J1E2
3
Clear
2
Technical Product Specification Quick Reference Label Quick Start User Guide/System Configuration Guide Additional Reference documents available at: http://www.intel.com/support/motherboards/server
Power LED
Password Clear 2 J1F1 3
HDD LED Power Button
NIC 1 Link/Act
Reset Button
TPM
Default
Default Password Clear
HDD LED
Internal USB
CMOS battery
2
J1F2
3
Default Enabled
NIC 2 Link/Act BIOS Recovery 2 J1F3 3
Default Recover
SYS FAN_4
RMM4 NIC
SATA 3 SATA 1 SATA 2 SATA 0
Internal USB Floppy Connector
IPMB
HSBP
SYS FAN_ 1 SATA_SGPIO
I
J
D
K
L D HDD 0
CPU Power Connector
HDD 1
HDD 2
G
HDD 3
Optical Device
C
Processor Socket
Internal USB SSD
SATA 4
P
F
Internal USB SATA 5
ME Force Update
RMM4 Lite
DIMM_A2
Front Panel Header (J1C1)
Available Documents
SATA Key
Video
DIMM_B1
Default
NIC1 USB0 USB1
DIMM_B2
3
Slot 6 ( PCIe x 8 ) LP Riser
2
J4A2
NIC2 USB2 USB3
H
Diagnostic LED Status LED ID LED Serial Port A
DIMM_A1
Chassis Intrusion
BMC Force Update
Slot 5 ( PCIe x 4 )
AXXVRAIL AXXSATADVDROM AXXRMM4 AXXRMM4Lite AXX4SASMOD AXXTPME3
O
M
E
Intel® Server Board S1200BTL Component Layout Value Rail kit SATA Slim-line DVD Intel® Remote Management Module 4 Intel® Remote Management Module 4 Lite Intel® SAS Entry RAID Module Intel® Trusted Platform Module
B C
USB USB Video 0, 1 2, 3
Optional Accessories/Spares and Order Codes
B
H
G. Status/Fault LED H. Power Button I. HDD LED J. LAN4 LED K. LAN2 LED
USB 2.0 Connectors System ID Button NMI Button LAN1 LED LAN3 LED Reset Button
Slot 4 ( PCIe x 4 )
Serial Port A
Use the instructions provided with the RAID
Slot 3 ( PCIe x 4 )
AC Power
controller and with the operating system.
A
Use the instructions provided with the RAID A
C. Install your Operating System:
NIC2
A
DIMM B1
B. Configure your RAID Controller:
I
K J
DIMM A1
2. Connect your keyboard, mouse, video and other I/O cables/devices as shown. Then connect the AC power cord.
Look on the Server/System Management screen in the BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at: http://www.intel.com/support/motherboards/server If new versions are available, update the BIOS on your server. See the Techinical Product Specification on the Intel® Server Deployment Toolkit CD for update instructions.
DIMM A2
CAUTION: This unit must be operated with the TOP COVER installed to ensure proper cooling.
1. Make sure you have replaced the system cover.
NIC1
(shown with bezel removed)
A. Confirm BIOS Version:
Before installing your operating system, you must finish your system installation and connect back panel I/O connectors and AC power.
Platform Cabling Diagram
Front Panel Controls and Indicators
Software • BIOS, Drivers, and Operating System Installation
DIMM B2
16
Finishing Up
Slot 1 ( PCI )
15
SAS Module Connector
CPU Fan SYS FAN_2 Connector
SYS FAN_3
Main Power Connector
P/S AUX
A B C D A B C D E F
Server Board Power Supply Front Panel Board Backplane Power to Server Board (CPU) PSU Management Bus to AUX Power to Server Board (Main) Optical Device to Power Supply Power to Backplane Front Panel USB
G H I J K L M N O P
Front Panel HDD 0 to Server Board SATA 0 HDD 1 to Server Board SATA 1 HDD 2 to Server Board SATA 2 HDD 3 to Server Board SATA 3 Optical Device SATA Data Cable Link to Backplane SGPIO Blower Fan #1 Power Blower Fan #2Power Blower Fan #3 Power
Server Board SATA Connector Legend
5 4 3 2
1 0
