Transcript
GENERAC The Reliable Ones
1400PSI Double Insulated Owner’s Manual
Electric Pressure Washer
? emss? l b Pro stion ur unit o Que king y tore, er
h ta the s was ore Bef ack to ssure t b pre ea 8 the elplin l l a -140 h c
-270 CT 0 0 1-8 -F 8-5 M
Model No. 1455-0 (1400 PSI Electric Pressure Washer) Manual No. 185708 Revision 3 (5/25/2000) Visit our Generac website: www.generac-portables.com This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Generac Portable Products 1,400 PSI Electric Pressure Washer
EQUIPMENT DESCRIPTION
WARNING! To reduce the risk of
electrocution, keep all connections dry and off the ground. Do Not touch the plug with wet hands.
CONGRATULATIONS on your purchase of a GENERAC electric pressure washer. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
DANGER! Risk of Explosion Do Not spray flammable liquids.
This manual contains information for an electric pressure washer that operates at 1,400 PSI at a flow rate of 1.5 gallons per minute. This high quality system features a cart, pump with pressure activated start/stop system, GFCI power cord, turbo nozzle, utility brush, foamer bottle, safety goggles, 25 high pressure hose, and more.
Read all instructions before using this product. To reduce risk of injury, close supervision is necessary when a product is used near children. Do Not allow children to operate the pressure washer at any time.
Please read and retain this manual. The instructions will enable you to assemble your unit and maintain your pressure washer properly.
Stay alert. Watch what you are doing.
Every effort has been made to ensure that the information in this manual is both accurate and current. However, Generac reserves the right to change, alter or otherwise improve the product and its documentation at any time without prior notice.
Keep operating area clear of all persons.
Do Not operate the product when fatigued or under the influence of alcohol or drugs. Do Not overreach or stand on unstable support. Keep good footing and balance at all times. Do Not by-pass any safety device on this machine. Inspect cord before every use. Do Not use if cord is damaged.
Should you experience any problem you cannot easily remedy, call the pressure washer helpline at 1-800-270-1408.
Do Not touch plug with wet hands. For outdoor household use only.
CUSTOMER RESPONSIBILITIES
Locate this pressure washer in areas away from combustible materials, combustible fumes or dust. Do Not leave the spray gun unattended while the unit is connected to power.
Read and observe the safety rules. Follow regular schedule in maintaining, caring for and using your electric pressure washer.
Before starting the pressure washer in cold weather, check all parts of the equipment and be sure ice has not formed there.
For off-season storage, review Storage on page 11.
Units with broken or missing parts, or without protective housing or covers should Never be operated.
SAFETY RULES
Always wear eye protection when you use this equipment or when you are in vicinity where the equipment is in use.
WARNING! Risk of injury or injection Do Not discharge stream at persons.
Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
WARNING! Risk of injury or injection Unit
will start spraying when trigger is squeezed if On/Off switch is in On position. Point spray gun in safe direction.
2
Generac Portable Products 1,400 PSI Electric Pressure Washer
Extension Cords
Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury.
We Do Not recommend the use of extension cords with this device. If it is necessary to use one, however, then you must use only extension cords that are approved for outside use. These extension cords are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES. Also observe the following specifications:
Keep water spray away from electric wiring or fatal electric shock may result. High pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.
Cable Length: Up to 25 feet (8m) 50 feet (15m)
High pressure spray can cause particles to become airborne and fly at high speeds.
Wire Gauge: 14 AWG 12 AWG
Ground Fault Circuit Interrupter Protection
Inspect hose each time before using it. Water spraying from a leak is capable of injecting material into skin. Check all hoses for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings. If any of these conditions exist, replace hose immediately. Never repair high pressure hose. Replace it with another hose that exceeds maximum pressure rating of your pressure washer.
To provide protection from the risk of electrical shock, this electric pressure washer is equipped with a ground fault circuit interrupter (GFCI). Read the instructions on the plug for use or see Before Starting Pressure Washer on page 8. The GFCI device will disconnect both power conductors to the load circuit in the event of an interruption in either or both supply circuit power conductors. If power is interrupted in the line, the GFCI provides protection even if neutral is also grounded at the load.
Never move the machine by pulling on the high pressure hose. Use the handle provided on the cart or top of the unit. Keep the hose connected to machine and the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous.
IMPORTANT: The GFCI device will not automatically reconnect the circuit to the load after power is restored. After correcting any shorting problem, you must manually press the reset button to restore power to the pressure washer.
Never aim spray gun at people, animals or plants. High pressure spray may damage fragile items including glass. Do Not point spray gun at glass when in the high pressure mode.
Servicing of a DoubleInsulated Appliance
Hold the spray gun firmly in your hand when you use unit. Failure to do so could result in an injury from a whipping spray gun.
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor should a means for grounding be added to the product.
Operate and store this unit on a stable surface. Know how to stop the product and bleed the pressure quickly. Be thoroughly familiar with controls.
Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double-insulated product is marked with the words Double Insulation or Double Insulated. This symbol is marked on the product.
Store in a clean, dry and frost-free room. Follow the maintenance instructions specified in the manual.
3
Generac Portable Products 1,400 PSI Electric Pressure Washer
KNOW YOUR HIGH PRESSURE WASHER Read the owners manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future use. Spray Gun Utility Brush Grip Start System
Turbo Nozzle/ Wand
High Pressure Hose Foamer
High Pressure Outlet Master On/Off Switch
Water Inlet
Bayonet Adapter (not shown) Connector accommodates the connection of a utility and rotating brush to the spray gun. Foamer Used to apply detergent. Mixes water and detergent in outlet water flow. Goggles (not shown) Always wear eye protection when operating your pressure washer. Grip Start System Pressing and releasing the spray gun trigger starts and stops the electric motor in the pressure washer. High Pressure Hose Connect ends to spray gun and high pressure outlet. High Pressure Outlet Connection for high pressure hose.
Master On/Off Switch This switch ONLY enables the Grip Start system to function. QuickConnect (not shown) Allows rapid connection of your garden hose to the water inlet. Spray Gun Controls the application of water onto cleaning surface with trigger device. Includes safety latch. Turbo Nozzle/Wand Always attached to wand. Allows you to clean or rinse surfaces at high pressure. You cannot apply detergent using the turbo nozzle. Utility Brush Attaches to the spray gun with the bayonet adapter. Use this brush to scrub a variety of surfaces. Water Inlet Connection for garden hose.
4
Generac Portable Products 1,400 PSI Electric Pressure Washer
REMOVE PRESSURE WASHER FROM CARTON
Remove main unit.
Remove cart base.
Remove parts box.
Assemble cart as follows (refer to Figure 1): 1. Place wood block (not supplied) on hard surface. 2. Place axle (Item 5) on wood block and tap axle cap (Item 3) onto axle. 3. Install wheel (Item 4) on axle with raised hub away from axle cap and insert axle through mounting holes on cart base.
CARTON CONTENTS
4. Turn cart base on its side, resting axle cap on wood block.
The following parts are shipped loose with your pressure washer: Main unit
5. Install wheel (Item 4) on axle with raised hub toward cart base. Tap axle cap (Item 3) onto axle.
Cart base
Owners manual
Parts box (includes items listed below)
Safety glasses
Oring kit
Spray gun
Foamer bottle
Turbo nozzle/wand and utility brush
High pressure hose
Cart hardware parts bag
Cart handle, axle, wheels, and wire form
Garden hose quick connect fittings
Bayonet adapter
6. With the holes highest in the cart handle (Item 10) positioned to the rear of the unit, attach the handle to the cart base. Use one carriage bolt (Item 6) and one knob (Item 7) on each side of handle (note bolt insertion direction). 7. Slide two T-Head bolts (Item 8) into slots on bottom of pressure washer unit. 8. Align bolts on pressure washer to holes on cart base. Tighten to cart base with wing nuts (Item 2). 9. Insert wire frame accessory holder (Item 9) into rear cart handle holes as shown. 10. Insert the two vinyl caps (Item 11) onto the ends of the wire frame accessory holder. Figure 1 Cart Assembly
Become familiar with each piece before assembling the pressure washer. Check all contents against the illustration on page 4. If any parts are missing or damaged, call the pressure washer helpline at 1-800-270-1408.
CART ASSEMBLY To assemble your cart you need the following tools: Hammer Adjustable Wrench Phillips Screwdriver Wood Block
5
Generac Portable Products 1,400 PSI Electric Pressure Washer
PREPARING PRESSURE WASHER FOR USE
Attach the female quick connect to your garden hose. Attach garden hose to the water inlet using the quickconnect. The quickconnect should lock in place. (Figure 5).
Unwind the high pressure hose and attach it to spray gun (Figure 2).
Figure 5 - Connect Garden Hose to Water Inlet
Figure 2 Attach Hose to Spray Gun
Attach the high pressure hose to the high pressure outlet and tighten by hand (Figure 3).
Attach turbo nozzle or foamer bottle to spray gun as desired. See the sections Applying Detergent with Foamer (page 6) and How to Use the Turbo Nozzle (page 7).
Figure 3 - Attach Hose to High Pressure Outlet
HOW TO USE YOUR PRESSURE WASHER If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-270-1408.
Included with this unit is a quick-connect fitting that you must attach to the water inlet and your garden hose. You can install the male connector by hand but you may need to use an adjustable wrench to tighten it (Figure 4).
Applying Detergent With Foamer Pressure washers are useful cleaning tools designed to clean almost any surface in two easy steps.
Figure 4 - Install Quick-Connect
IMPORTANT: Use soaps designed specifically for pressure washers. Household detergents could damage the pump. NOTE: Never use garden hose inlet to siphon detergent or wax.
Female Quick-Connect
DANGER! You must attach all hoses and the spray gun before you start the motor.
Male Quick-Connect
WARNING! Before removing any spray gun
accessory, be sure to turn off the pressure washer and relieve pressure by pressing the trigger. You could be injured if you try to remove an accessory if the pressure washer is running and there is pressure in the system.
Check the screen on the female connector. Make sure it is clean and check for damage. If you see any damage in the screen, Do Not use that female connector. Call the pressure washer helpline to order a replacement.
6
Generac Portable Products 1,400 PSI Electric Pressure Washer
First, apply an appropriate detergent/solvent solution to penetrate and loosen grime. Apply detergent at low pressure to avoid splashing, overspraying and waste. Leave the solution on surface for 3 to 5 minutes to allow solution to work. Reapply as necessary to keep surface from drying.
effective when the tip of the wand is held between 8 to 24 inches from the surface being cleaned. Always start the turbo nozzle at a distance, gradually getting closer to the surface until you get the cleaning force you want.
CAUTION! The turbo nozzle produces an
The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean.
extremely high pressure spray which is capable of removing paint and cutting holes through surfaces if held too close. Always make sure the surface you will clean will not be damaged by the high pressure spray by testing in a hidden area.
To apply detergent follow these steps: Detach the turbo nozzle/wand from the spray gun. Remove the bottle from the foamer.
NOTE: You cannot apply detergent with the turbo nozzle.
Align the locking tabs on the foamer with the grooves in the spray gun. Push inward and twist clockwise to lock in place (Figure 6).
How to Use the Utility Brush
NOTE: Make sure that when you lock the foamer into place, have the hose that goes to the foamer bottle hanging downward.
The utility brush allows you to scrub surfaces with water filtering through the bristles.
Prepare your detergent solution as required by the manufacturer and fill bottle with the solution.
To attach the utility brush to the spray gun: Tighten the bayonet adapter to the brush base.
Attach bottle onto foamer making sure the bottle hangs down.
Remove the turbo nozzle/wand from the spray gun if attached.
Start washer and apply detergent to a dry surface, starting from the bottom and working up.
Attach the brush with the bayonet adapter to the spray gun by aligning the locking tabs on the adapter with the grooves in the spray gun. Push the brush inward and twist clockwise to lock in place (Figure 7).
To rinse, YOU MUST stop the pressure washer, remove the foamer and connect the turbo nozzle/ wand.
Figure 7 - Attaching Utility Brush to Spray Gun
NOTE: Detergents are most effective applied to a dry surface.
How to Use the Turbo Nozzle The turbo nozzle rotates the high pressure stream in a rapid circular pattern. The high pressure spray is most
NOTE: You must use the bayonet adapter to attach the brush to the spray gun.
Figure 6 - Connect Foamer to Spray Gun
7
Generac Portable Products 1,400 PSI Electric Pressure Washer
BEFORE STARTING PRESSURE WASHER
Check that high pressure hose is attached to pump outlet and the spray gun. Connect the garden hose to the water inlet.
WARNING! There MUST be at least ten feet
To operate the unit you must do the following every time you use your unit: Press the units master ON/OFF switch to the OFF position.
of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a Y shut-off connector or other convenience-type water shut-off valve. Damage to pressure washer resulting from disregarding this warning will not be covered by the warranty.
Plug unit into an electrical circuit rated for 120 Volts AC at 15 Amps. Press the Reset button on the plugs GFCI (Figure 8).
Remove any accessories connected to the spray gun.
Figure 8 - GFCI Power Cord
Press the units master ON/OFF switch to the OFF position (Figure 9). Reset
Test
Figure 9 - Master Switch On /Off
Operating Instructions
Press the Test button. The red indicator on the reset button should appear.
Turn ON water. Water supply should not exceed 104°F. Use a cold water source.
Press Reset button again. The unit is ready to use.
WARNING! Never leave the pressure washer
IMPORTANT: Do Not use your electric pressure washer if the GFCI test fails.
unattended while it is plugged into an electrical outlet and while water is supplied to the machine.
STARTING YOUR PRESSURE WASHER
Squeeze trigger on spray gun until you have a steady stream of water (approximately 12 minutes). This will purge air from the system.
DANGER! To reduce risk of electrocution, keep all connections dry and off the ground. Do Not touch plug with wet hands.
Adjust the safety latch on spray gun to ON position (Figure 10). Figure 10 - Safety Latch Engaged
WARNING! Never put hands in front of spray. CAUTION! Spray gun kicks back. Grasp spray gun with both hands when spraying.
WARNING! Risk of injury Do Not discharge stream at persons or animals.
8
Generac Portable Products 1,400 PSI Electric Pressure Washer
SIPHONING
Reconnect desired accessories. Turn the master switch to ON position.
Do Not siphon your water supply. Connect only to household water supply.
Place safety latch in OFF position and squeeze trigger on spray gun. Pump will start and water should stream from the nozzle.
TIPS
CAUTION! Water must be supplied to the
Never leave the pressure washer unattended while it is plugged into an electrical outlet and while water is supplied to the machine.
pump before turning unit on! The pump will run without water supplied, resulting in pump damage that is not covered by the warranty.
Never use the garden hose inlet to siphon detergent or wax.
STOPPING YOUR PRESSURE WASHER
If you have the nozzle too far away, the cleaning will not be as effective.
The pressure washer motor runs only when the trigger is engaged. To stop the pressure washer, release trigger and the motor will shut OFF.
SPECIFICATIONS Pressure . . . . . . . . . . . . . .1400 PSI
DANGER! Releasing the trigger will shut off the motor but does not shut off electrical power to the unit.
Flow Rate . . . . . . . . . . . . .1.5 GPM Water Supply
Press the Master ON/OFF switch so it is in the OFF position.
Temperature . . . . . . . . . . .Not to exceed 104°F
Turn off water supply.
Motor . . . . . . . . . . . . . . . . Brush Type
Squeeze the trigger on the spray gun to relieve built up pressure in the unit.
Rated Voltage . . . . . . . . . 120 Volts AC
Disconnect GFCI plug from outlet and coil power cord.
Current . . . . . . . . . . . . . . .14 Amps
9
Generac Portable Products 1,400 PSI Electric Pressure Washer
GENERAL MAINTENANCE RECOMMENDATIONS
Press the Reset button on the plugs GFCI. Press the Test button. The red indicator on the reset button should appear. Press Reset button again for use.
The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual.
IMPORTANT: Do Not use your electric pressure washer if above test fails.
O-Ring Maintenance Your pressure washer uses o-rings to keep hose and spray gun connections tight and leak-free. Through the normal operation of your unit, these o-rings may become worn or damaged.
BEFORE EACH USE Check and Clean Quick-Connect Screen
Provided with your pressure washer is an ORing Maintenance Kit which includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your units o-rings. Note that not all of the parts in the kit will be used on your unit.
Remove quick-connect and examine inlet screen on the female connector. Clean if it is clogged or replace if it is damaged in any way.
Check High Pressure Hose
Parts in the ORing Kit include: ORing (Light Blue), p/n B2688, for the male accessory connections of the power foamer and utility brush (Figure 11).
High pressure hose can develop leaks from wear, kinking, abuse. Inspect hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings. If any of these conditions exist, replace hose immediately.
Figure 11 - O-Ring for Male Accessory Connections of Power Foamer and Utility Brush
DANGER! Water spraying from a leak is capable of injecting material into skin. Never repair a high pressure hose. Replace a bad hose with a hose that exceeds the maximum pressure rating of your pressure washer.
Check Spray Gun and Wand Examine hose connection to spray gun and make sure it is secure. Test trigger by pressing it and making sure it springs back into place when you release it. Put safety latch in ON position and test trigger. You should not be able to press trigger.
ORing (Light Green), p/n B2264, for the turbo nozzle (Figure 12). Figure 12 - O-Ring for Turbo Nozzle
Check GFCI Press the units master ON/OFF switch to the OFF position. Plug unit into an electrical circuit rated for 120 Volts AC at 15 Amps.
10
Generac Portable Products 1,400 PSI Electric Pressure Washer
ORing (Red), p/n B2726, for the bayonet adapter (Figure 13).
ORing (Yellow), p/n B2264, for the ends of the high pressure hose (Figure 16). Figure 16 - O-Ring for Ends of High Pressure Hose
Figure 13 - O-Ring for Bayonet Adapter
Rubber Washer, p/n B2385, for the inside of the garden hose connector (Figure 14).
To remove a worn or damaged ORing: Use a small flathead screwdriver to get underneath the o-ring and pry it off.
Figure 14 - Rubber Washer for Inside Garden Hose Connector
STORAGE Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and freeze pump action. After each time you are finished using your pressure washer, follow this procedure: Switch the Master ON/OFF switch to OFF, unplug it, then remove all the hoses.
Water Inlet Screen (p/n B2384) for the garden hose connector (Figure 15).
Coil the high pressure hose and inspect it for damage. Cuts in the hose or fraying of it could result in leaks and loss of pressure. Should any damage be found, replace the hose. Do Not attempt to repair a damaged hose.
Figure 15 - Water Inlet Screen for Inside Garden Hose Connector
Wipe off and coil your GFCI power cord. Drain water from hose and properly store it to prevent cuts and general wear. Store the pressure washer and its components in an area which will be above freezing temperatures. Store in a clean, dry, frost-free room.
11
Generac Portable Products 1,400 PSI Electric Pressure Washer
NOTES
12
Generac Portable Products 1,400 PSI Electric Pressure Washer
TROUBLESHOOTING Problem
Pressure washer will not start. Pressure washer does not start when trigger is activated.
Cause
No electrical power is available. 1. Trigger not open. 2. Main power switch not in ON position. 3. Electrical defect. 1. Pump is sucking air.
Pressure washer does not produce pressure. 2. Water filter clogged. 3. Pump is defective. 1. Water supply inadequate. High pressure spray is irregular. No foam or detergent from accessories. Unit does not shut off when trigger is released. Unit turns on and off (cycles) when the trigger is pressed.
2. Air in pump system. 1. Detergent in foamer bottle is fully diluted. 2. Foamer is defective. 1. Air in pump system. 2. Inadequate water supply. Clogged spray nozzle.
13
Correction
Check cable, power socket, GFCI plug and fuse/circuit breaker. Reset GFCI. 1. Open trigger. 2. Turn main power switch on.
3. Contact Generac service facility. 1. Water hose must be minimum1/2" diameter. Make sure water supply is ON. Make sure water supply is clean. Check all connections for leaks or blockage. 2. Clean filter. 3. Contact Generac service facility. 1. Turn ON water to full position. Check connections for leaks or blockage. 2. Remove any accessories and press trigger until steady stream of water is present. 1. Drain diluted liquid and add detergent to foamer bottle. 2. Contact Generac service facility. 1. Remove any accessories and press trigger until steady stream of water is present. 2. Make sure water is turned on fully. Remove nozzle and operate with gun only. If cycling persists, contact Generac service facility. If cycling ceases replaces spray nozzle with new.
Generac Portable Products 1,400 PSI Electric Pressure Washer
EXPLODED VIEW UNIT 14
14
Generac Portable Products 1,400 PSI Electric Pressure Washer
PARTS LIST UNIT Item 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 20 21 22 23 24 25 26 28 29 30 32 33 34 35 37
Part # Qty. Description N/A 1 ASSY., Motor and Pump (see pages 16-17) B1415 1 DECAL, Circuit 185917 1 DECAL, Unit 185946 1 DECAL, Instructions 98806 1 FOAM, Air In, Fan-end 97893 1 HOUSING, Switch and Cord 20984 1 SWITCH, Rocker 16A 98801 4 MOUNT, Rubber B1566 1 COVER, Motor 20985 1 ENCLOSURE, Rocker Switch Boot 20986 1 BOOT, Rocker Switch 84543B 2 SCREW, 3.5mm x 12mm Plastite B5597 1 CORD, Power w/ GFCI 84358 10 SCREW, #6-19 x .75 mm Plastite 99349 1 STRAIN RELIEF, Cord NSP 1 DECAL, ETL 21334 1 HOUSING, Inlet 21335 1 HOUSING, Outlet 21265 1 QUICK DISCONNECT, Male 96016 1 QUICK DISCONNECT, Female A1484 1 NUT, Strain Relief Lock A1485 1 SEAL RING, Strain Relief 97835 1 "O" RING, Hsg Seal, dia. 82.2 x 2.62mm 21336 1 GUN, Spray 21337 1 WAND, Extension B3337 1 HOSE, High Pressure B1935 1 FOAMER B1051 1 ADAPTER, Accessories 87815 1 GOGGLES, Safety B1300D 1 NOZZLE, Turbo 88185 1 BRUSH, Utility
15
Generac Portable Products 1,400 PSI Electric Pressure Washer
EXPLODED VIEW PUMP/MOTOR
a a
16
Generac Portable Products 1,400 PSI Electric Pressure Washer
PARTS LIST PUMP/MOTOR Item 1 2 3
Part # B1514 40945 97835
Qty. 1 3 1
4
20610
2
5
97822
1
6 7
B2663 97826
1 1
8
97824A
1
9
97825
1
10 11 12 13 14
97833 97830 97832 99503 A1495
1 3 3 3 2
15 16 17 18 19 20 21 22
21055 28739A 20138 20928 B3660 B3568 21126 21125
1 1 1 1 1 1 1 1
Description ASSY, Motor Complete BOLT, SHCS M6-1.0 x 20mm "O" RING, Hsg Seal, dia. 82.2 x 2.62mm WASHER, Brg dia. 35 x 55 x 3mm BEARING, Ndle Thrust dia. 35 x 52mm ASSY., Cam/Gear WASHER, Brg dia. 40 x 60 x 1mm BEARING, Needle dia. 40 x 60mm WASHER, Brg dia. 36 x 60 x 6mm SHAFT, Idler Axial Cam RETAINER, Piston Spring PISTON, dia. 15 x 65mm SPRING, Piston Return TAPTITE, M4-0.7x10mm SW MTG GROMMET, Rubber TIE, Wrap SWITCH, Auto HOUSING, Auto-Switch SPRING, P.A.S.S. PISTON ASSY, P.A.S.S. RING, Backup dia. 26.0 Id "O" RING dia. 25.07 Id x 2.62 Cs [.103"]
Item 23 24 25 26 27 28 29 30 31 32 33 34 37 38 39 40 41 42 43 44 45 46 48 49 50
17
Part # 20217 21124
Qty. Description 1 STOP, Piston Return 1 RING, Backup dia. 4.34 Id x 1.24 20218 1 CAP, Retainer 21123 1 "O" RING dia. 3.68 Id x 1.78 Cs [.070"] B1124 1 CAP, Inlet 97855 1 "O" RING, dia. 6.5 x 2.01mm 97100 1 CAP, High Pressure B3570 1 HOUSING, Piston 93680 3 SEAL, Oil-piston dia. 15 TC4 97831 3 SPACER, Pilot 97929 1 SPRING, Check Valve B3569 1 VALVE, Shuttle 97841 3 CAP, Check Valve 97840 3 "O" RING, Hi-press dia. 15.6 x 1.78mm B1449 6 ASSY., Check Valve 97934 7 "O" RING, Chk Valve dia. 12.4 x .78mm 76353A 1 PLUG, Taper dia. 5.4 97852 1 BALL, dia. 3/16" Pop-off Valve B2240 1 SCREW, Lock Socket A1130 1 SPRING, Pop-off Valve B1960 1 SEAT, Ball 40946 4 BOLT, SHCS M6- 1.0 x 35mm B3571 1 PUMP, Head 93667 3 SEAL, Piston "U" Cup B2020 1 O-RING, 3.68 I.D. x 1.78 CS ELF
Generac Portable Products 1,400 PSI Electric Pressure Washer
EXPLODED VIEW AND PARTS LIST CART
Item 1 2 3 4 5 6 7 8 9 10 11
Part # Qty. Description BB2446 1 BASE, Cart 21497 2 NUT, M6 Plastic Wing 75402B 2 CAP, Axle B2238 2 WHEEL B2215 1 AXLE B3083 2 BOLT, Carriage, M6 x 1.0 x 30 21865 2 KNOB, Handle 21498 2 BOLT, M6 T-Head (to fit in unit housing) B2212 1 ACCESSORY, Holder B2611 1 HANDLE, Cart B1459 2 CAP, Vinyl Black
18
Generac Portable Products 1,400 PSI Electric Pressure Washer
NOTES
19
LIMITED PRESSURE WASHER WARRANTY GENERAC PORTABLE PRODUCTS (hereafter referred to as the COMPANY) warrants to the original retail purchaser, the pressure washer manufactured by the COMPANY to be free from defects in material and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term original purchaser means the person for whom the pressure washer is originally purchased. Warranty Schedules Electric Power Washer All Other Engine-driven
1 year (does not apply to commercial or rental applications) CONSUMER* COMMERCIAL* Engine: Warranted solely by Warranted solely by Engine Manufacturer Engine Manufacturer Pump: 1 year 90 days
* NOTE: For the purpose of this warranty consumer use means personal residential household use by original purchaser. Commercial use means all other uses, including rental, construction, commercial and income producing purposes. Once a pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for the purposes of this warranty. During said warranty period, the COMPANY will, at its option, repair or replace any part which, upon examination by the COMPANY or COMPANY-Authorized Dealers, is found to be defective under normal use and service**. All transportation costs under warranty, including return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser. ** NORMAL WEAR: As with all mechanical devices, pressure washers need periodic parts service and replacement to perform well. This warranty does not cover repair when normal use has exhausted the life of a part or pressure washer pump. This warranty does not include: Used products and demonstration equipment. Parts, such as GUNS, HOSES, WANDS, NOZZLES or other wear items such as quick couplers, oil, gauges, belts, o-rings, filters, pump packing, etc. Pumps which have been run without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freezing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.). THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, THE COMPANY MAKES NO OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO THE TIME PERIOD AS SPECIFIED IN THE EXPRESS WARRANTY. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF THE COMPANY'S NEGLIGENCE. THE COMPANY ALSO DISCLAIMS ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS THE LOSS OF TIME OR THE USE OF THE POWER EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE OF THE EQUIPMENT: AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. For service, see your nearest COMPANY-Authorized warranty service facility or call 1-877-544-0982. Warranty service can be performed only by a COMPANY-Authorized service facility. This warranty will not apply to service at any other facility. At the time of requesting warranty service, evidence of original purchase date must be presented.
Generac Portable Products Jefferson, Wisconsin U.S. A.
