Transcript
FILE NO. 050-200307
SERVICE MANUAL
COLOR TELEVISION
14AF43
DOCUMENT CREATED IN JAPAN, Apr., 2003
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
(INSULATION CHECK PROCEDURE)
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
[Note 2]
External exposure metal: Antenna terminal Earphone jack
HOW TO ORDER PARTS Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.
IMPORTANT Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
A1-1
TABLE OF CONTENTS SERVICING NOTICES ON CHECKING ..................................................................................... HOW TO ORDER PARTS .......................................................................................................... IMPORTANT ............................................................................................................................... TABLE OF CONTENTS .............................................................................................................. GENERAL SPECIFICATIONS ................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ............................................................................................... 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ SERVICE MODE LIST ................................................................................................................ CONFIRMATION OF HOURS USED ......................................................................................... WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................. BLOCK DIAGRAMS ................................................................................................................... PRINTED CIRCUIT BOARDS MAIN/CRT ................................................................................................................................ SCHEMATIC DIAGRAMS MICON ..................................................................................................................................... CHROMA ................................................................................................................................. DEFLECTION/CRT .................................................................................................................. POWER ................................................................................................................................... SOUND .................................................................................................................................... TUNER/STEREO ..................................................................................................................... AV ............................................................................................................................................ CRT .......................................................................................................................................... COMB/FILTER ......................................................................................................................... WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... ELECTRICAL REPLACEMENT PARTS LIST ...........................................................................
A2-1
A1-1 A1-1 A1-1 A2-1 A3-1~A3-5 B1-1 B2-1, B2-2 C1-1 C1-1 C1-1 D-1~D-5 E-1, E-2 F-1~F-4 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 H-1, H-2 I-1 J1-1 J2-1~J2-4
GENERAL SPECIFICATIONS G-1
TV System
CRT
CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH
14 inch / 357mmV Flat 90 degree +0.45G/0.18G NTSC 2 Speaker Front Side 1.6 x 2.8 Inch 8 ohm 2.5+2.5 W 2.0+2.0 W No US System M 1Tuner USA(W/ CATV) F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz
Color System Speaker
Sound Output
G-2
Tuning System
NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH
Intermediate Frequency
G-3
Power
Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source
Position Size Impedance MAX 10%(Typical)
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
AC DC
Power Consumption
Protector G-4
Regulation
G-5
Temperature
G-6
Operating Humidity
at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage
A3-1
80 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes UL/CSA FCC/IC DHHS/HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
GENERAL SPECIFICATIONS G-7
On Screen Display
Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance Stable Sound On/Off Surround On/Off Set Up TV/CATV Auto CH Memory Add/ Delete Option Language CH Label Favorite CH V-Chip Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9
G-8
OSD Language
G-9
Clock and Timer
Sleep Timer
No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes English
Max Time Step Program(On Timer / Off Timer / Clock)
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
A3-2
Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
more than
French
Spanish
120 Min 10 Min Yes --
No Min
Sec
GENERAL SPECIFICATIONS G-10
Remote Control
Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys
Multi Brand Keys
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up/+ CH Down/Volume Up/+ Volume Down/C.C.(TV/Caption/Text) CH1/CH2 TV/Video(Input Select) CH RTN(Quick View) SLEEP RECALL(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav. Up Fav. Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE DVD MENU < DVD MENU > DVD CLEAR TOP MENU DVD MENU
A3-3
RC-GF Yes Toshiba TV:40-BFh 3V UM-4 x 2 pcs 49 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
GENERAL SPECIFICATIONS G-11
Features
Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip
Yes Yes No Yes No No
Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter
G-12
Accessories
Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Station List Important Safety Instructions Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) PTB Sheet ESP Card 300 ohm to 75 ohm Antenna Adapter
A3-4
Yes Yes Yes USA,Toshiba Type No No No Yes No Yes No No No Yes 3 Lines Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes English / French Yes Yes No
No No No No No No No No No No No No Yes UM-4 x 2 No No No Yes No Yes No
GENERAL SPECIFICATIONS G-13
Interface
Switch
Front
Rear
Indicator
Terminals
Front
Rear
G-14 G-15
Set Size Weight
G-16
Carton
Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input = VIDEO3 Audio Input = VIDEO3 Other Terminal Video Input(Rear1) = VIDEO1 Video Input(Rear2) = VIDEO2 Audio Input(Rear1) = VIDEO1 Audio Input(Rear2) = VIDEO2 Video Output Audio Output Euro Scart Color Stream S Input Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.)
Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test
G-17
Cabinet Material
Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand
A3-5
Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2 Head Phone RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 No RCA x 3 Yes No No No F Type No 432 x 386 x 344.5 11.0kg ( 24.3 lbs) 13.0 kg ( 28.7 lbs) No ---Sets -/--- x -- x --Yes Double/Brown 540 x 460 x 465 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 62 550 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to remove the other.
1. REMOVAL OF ANODE CAP Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
REMOVAL Location of Anode Cap
1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged.
Fig. 1-3 GND on the CRT
NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
CRT
Screwdriver
Support Alligator Clip Fig. 1-4
GND on the CRT
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
CRT
Support
CRT Support
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
Fig. 1-2
B1-1
Fig. 1-5
DISASSEMBLY INSTRUCTIONS 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.)
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL
NOTE 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.)
Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Masking Tape (Cotton Tape)
Blower type IC desoldering machine
IC
Tweezers
Fig. 2-1 IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) 4. Peel off the Masking Tape.
NOTE
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.)
Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely.
NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
IC pattern
Fig. 2-2
B2-1
Fig. 2-4
DISASSEMBLY INSTRUCTIONS INSTALLATION
4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
IC
NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Soldering Iron
Supply soldering from upper position to lower position
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 2-7 B2-2
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key
Remocon Key
VOL. (-) MIN
0
Releasing of V-CHIP PASSWORD.
1
Initialization of the factory. NOTE: Do not use this for the normal servicing. If you set a factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours.
VOL. (-) MIN
Operations
POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". VOL. (-) MIN
6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
VOL. (-) MIN
8
Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
9
Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF HOURS USED POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". ADDRESS DATA 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. Initial setting content of MEMORY IC. INIT 00 50 3. After the confirmation of using hours, turn off the power. POWER ON total hours. CRT ON 0010 = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
FIG. 1
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 1F due to the adjustment value. INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
00
50
E8
0A
65
5E
B3
24
B7
39
AC
0A
04
40
40
40
7F
10
50
00
00
00
00
00
00
00
28
0F
0D
C2
A6
88
43
00
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C-1
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
2. BASIC ADJUSTMENTS 2-1: CONSTANT VOLTAGE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies.
1. Place the set with Aging Test for more than 5 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Connect the digital voltmeter to the TP003. 5. Adjust the VR502 until the digital voltmeter is 115 ± 1V.
CAUTION • Use an isolation transformer when performing any service on this chassis. • Before removing the anode cap, discharge electricity because it contains high voltage. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. • When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)
2-2: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 3. Adjust the Screen Volume until a dim raster is obtained. 2-3: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment.
Prepare the following measurement tools for electrical adjustments.
1. Place the set with Aging Test for more than 10 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select “R. DRIVE”. 5. Press the CH. UP/DOWN button on the remote control to select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or “B. DRIVE”. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and B. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white.
1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
TV
2-4: FOCUS
00 OSD
1. Receive a broadcast. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct.
24
2-5: HORIZONTAL PHASE
Fig. 1-1
1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "H.PHAS". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.
2. Use the Channel UP/DOWN button or Channel button (09) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments. NO. 00 01 02 03 04 05 06 07 08 09 10 11 12
FUNCTION OSD H CUT OFF H.VCO H.PHASE AFC GAIN V.SHIFT H.SIZE V.SIZE V.LINEARITY VS CORRECTION R DRIVE B DRIVE R BIAS
NO. 13 14 15 16 17 18 19 20 21 22 23 24 25
FUNCTION G BIAS B BIAS BRIGHT MAX BRIGHT CENT BRIGHT MIN CONTRAST MAX CONTRAST CENT CONTRAST MIN COLOR MAX COLOR CENT COLOR MIN TINT SHARPNESS
NO. 26 27 28 29 30 31. 32. 33. 34. 35.
FUNCTION CB DELAY FINE CR DELAY FINE CB PEDESTAL ADJ CR PEDESTAL ADJ E/W PARABOLA E/W CORNER E/W TRAPEZIUM LEVEL SEPARATION 1 SEPARATION 2
2-6: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask.
Fig. 1-2 D-1
ELECTRICAL ADJUSTMENTS 2-7: VERTICAL SIZE
2-10: TINT/COLOR CENT
1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V.SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 ± 2%. 5. Receive a broadcast and check if the picture is normal.
1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP024. 3. Using the remote control, set the brightness, contrast, color and tint to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select “TINT”. 5. Press the VOL. UP/DOWN button on the remote control until the section “A” becomes a straight line (Refer to Fig. 2-1). 6. Connect the oscilloscope to TP023. 7. Press the CH DOWN button 2 times to set to “COL. CENT” mode. 8. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 5 scales on the screen of the oscilloscope. 9. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 115 ± 10% of the white level. (Refer to Fig. 2-2) 10. Receive the color bar pattern. (Audio Video Input) 11. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~9. 12. Press the TV/VIDEO button on the remote control to set to the CS mode. 13. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select “TINT”. 14 Press the VOL. UP/DOWN button on the remote control until the tint step No. becomes “53”. 15. Press the CH DOWN button 2 times to set to “COL.CENT” mode. 16. Press the VOL. UP/DOWN button on the remote control until the color step No. becomes “69”.
2-8: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-7. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select "V.LIN". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-9: BRIGHT CENT 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select “BRI. CENT”. 2. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes “77”. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3.
“A” Fig. 2-1
White 100% RED Level
D-2
Fig. 2-2
ELECTRICAL ADJUSTMENTS 2-11: CONTRAST MAX MANUAL
2-13: LEVEL
1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "74". 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote to set to the AV mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 6. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "86". 7. Receive a broadcast and check if the picture is normal. 8. Press the TV/VIDEO button on the remote to set to the CS mode. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 10. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "90". 11. Receive a broadcast and check if the picture is normal.
1. Receive the monoscope pattern (70dB). 2. Connect the AC voltmeter to pin 6 of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select "LEVEL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 ± 2mV. 2-14: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3)
TV
00 OSD
24
2-12: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment.
A
B
Fig. 2-3
Method (1) 1. Set the multi-sound signal generator for each different Lch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select “SEP 1”. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to “SEP 2” mode. Then perform the above adjustment 4.
2-15: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 02 04 05 06 09 15 17 19 20 21 23 25 26 27 28 29 30 31 32
Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack (R-ch). 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select “SEP 1”. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the Audio Out Jack (L-ch). 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select “SEP 2”. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. D-3
FUNCTION H.VCO AFC GAIN V.SHIFT H.SIZE VS CORRECTION BRIGHT MAX BRIGHT MIN CONTRAST CENT CONTRAST MIN COLOR MAX COLOR MIN SHARPNESS CB DELAY FINE CR DELAY FINE CB PEDESTAL ADJ CR PEDESTAL ADJ E/W PARABOLA E/W CORNER E/W TRAPEZIUM
STEP NO. 03 04 00 00 42 125 50 50 18 90 00 40 00 00 08 08 31 31 31
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE Adjust after performing adjustments in section 3-2.
NOTE
1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets.
1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7.
3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB
RGB
R G B
R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
3-2: PURITY
Fig. 3-2-a
NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw.
WEDGE
WEDGE
WEDGE WEDGE POSITION
DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW
Fig. 3-2-b
PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1
D-4
ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB CP806 TP024
R805
TP023
J801
CP803 CP802B
R803
CP801B
CD801 CD802 CRT
CP801A CP101 TU001
FB401 CP401 VR401 TP003 W003
VR502
CRT
SPEAKER
CP802A CP502
L503 CRT
AC IN J705
CD501
J706
CP1001 J707
MAIN PCB
D-5
BLOCK DIAGRAM
A/V OUT J708 6 COMB FILTER IC IC1501 LA76600M-TLM
4
CHROMA IC IC601 M61283FP
2 18 C OUT
FB401
60
AMP
16 Y OUT Y IN 3
VIDEO LINE OUT
J801
Q603, Q614, Q605 VIDEO SW(Y) IC IC1502 MM1501XNRE S-JACK J702 LINE1(REAR) J701
6 Vin1 V.OUT 2
3
Vin2
4
4
B OUT 16 51 VIDEO SW(C) IC IC1503 MM1501XNRE 6 Vin1 V.OUT
6
4
3
FRONT -VIDEO J705
2
R OUT 14 49
C IN(Y/C)
CVBS2
6
38
CVBS3
3
53 CVBS4
2
H.DRIVER
R IN 23
34 RED R
44
U IN(YUV)
B IN 21
36 BLUE B
2
40
V IN(YUV)
FAST BLK 24
TU001 26
6 Vin1 Vin2 V.OUT
2
27
5
DY
OS101
REMOCON 9
1
D109
ON_TIMER 10 X.IN 19
30 SCL1
X.OUT 20
31 SDA1
KEY1 6
POWER X101 8MHz
VOL DOWN CH DOWN
KEY2 7 VOL UP CH UP SPEAKER SP1001
5 SDA SCL
MEMORY IC IC199 S-24C16AFJA-TB-01
SPEAKER SP1002
2
7 18
AUDIO SW(R) IC IC701 MM1501XNRE
6
19
6 Vin1 V.OUT 2
1
14
3
2
V-OUT IC IC401 AN5522
33 BLANK X602 3.579545MHz
SCL
6 2
CRT V801
SOUND DECORDER IC IC902 AN5829S
24
FRONT-AUDIO.L J706
XTAL 3.58 34
SDA
HV
9
MICON IC IC101 OEC7090A
3
13
S
H.OUT
35 GREEN G
AUDIO SW(L) IC IC702 MM1501XNRE
4
H OUT 8
G IN 22
17
8
Q405
Y IN(YUV)
11
F
7
48
10
FRONT-AUDIO.R J707
Q801, Q804 RED/GREEN OUT
5
YUV_IN(REAR) J704
4
Q803, Q805 GREEN/RED OUT Q402
42
LINE2(REAR) J703
3
F
V OUT 63
Vin2 46
2
BLUE OUT
G OUT 15
Y IN(Y/C)
CVBS1
2
1
Q802, Q806
23
2
21
3
16
2
12
3
22
30
19
5
7
4
Vin2 Q901
TONE CONTROL IC IC302 AN5891SA-E1V
HEADPHONE_JACK J1001
5 SOUND AMP IC IC1001 AN5276
1
BUFFER Q902 BUFFER
E-1
E-2
PRINTED CIRCUIT BOARDS MAIN/CRT (INSERTED PARTS) SOLDER SIDE R443 D404
R430 R438
R402
R432
C418 C420
W009
W010
W011
W853
W821
D524
R542 W005
D506
D507
Q514
C535
R536
C539
C507
R502
C512
W004
B504
W801
R503
B501
D512
C527
C504
D514
CD801B
W033
W802
CD802B W012
R500
C513_1
R807
D504
Q806
CP502
Q804
R806
D501
C801
C110
C109
C122 W028
Q805 W056
CP508
C502 TH501_1
D812 D801
Q803
CP507
C506_1
C804 D803
C139
Q801 D802
C523
C503
CP801B D810 Q802
D811
R824
D502
_1
CP802B
RY501
D516
C519
W035
S805Y
D525
D508
D503
W013
D520
W043
W042
Q504
R501
D523
C550
R547
R510
R540
R539
W825
C520
R541_1
C501
W806
D505
_2
C114
D113
W049
C802
W015
R805
CP806
R804
CP501 L501
C505_1
C108
SW105
FH502
F501
FH501
OS101
SW102
D109
R120
SW101
R102
SW104
R520
R133
W016
01
R802
J8
W052
W054
W822
R803
R515
RISK OF FIRE - REPLACE AS MARKED.
W055
W053
R118
W116
SW103
R544
D509
W817
R553
R554
R527
R535 W008
C113
R140
W123
R146
W120
W118
R139
W119
C516
D517
D106 X101_1
HS501
T501_1
S805X
R130 W128 R119
C907
C904
C916 D706
W129
C910
W117
W175
C302
C305
C308
R301
W121
C905 J705
L901
C914
C903
W176
W174
C314
C316
W177
W178
W179
W126
W125 W180
W811
D105
C306
C333
R304
R303
W832
R302
CP1001
C403
W032 W037 W038 W040
R132
R124
W030
W097 W103
W805
W106
D104
W093
C919 W829
R524
Q508
R001
R002
W107 W108
W112
W114 W099 W111 W098
W096
C901
C902
C304
C317
C319 W181
R512 D406
W094
W830
C509
Q502
R508
CP803
W091
R545
R546
W039 W029
R904 R905
R506 D528
C521
R452_1
W044 W041
R543_1
D511
R426
W046 W045
W104 W109 W101 W102
W100
R902
R901
W092
W157
D510
Q509 W023
W113
C638
C646 W095
CP802A
C409
B405
W027
X602
D607 W184
D606
D605
W165
W164
W110
C647
W170 R626
R623
W815
L1512
W168
W163 W166 L1503
W161
W160
L1502 W831
CD802A
J706
W019
W823
R414
C406 C408
C630
W082
C629
C615 W169
W807 C517
R537
C401
W080
W167
L301
Q512
S804Y W022
Q505
T401_1
D414
W081
Q507
R507
R505
R406
W048
C606 C639
C1502
C1530
C1501
C1525
C602
Q611
_1
W002
C524
C402
W026 W025
Q601
08
VR502
Q503
Q402
W115
C5
R428
W084
C645
C627
C609
C608
02 R6 C1518
W848
W139
D604
L402_1
R437 R413
C407
R416
C611
C603
C1520
L1505
C1510
W140
R601
L401
C410
R429
VR401_1 R420
D415
W844
C621
C618
C642
C605
W083
W003 FB401
IC504
W087
Q602
W172
F-1
R517_1
D513
C622
C610
L1508
R648
J707
R436
C708
W147
D602
W154
W151
R603 W155 W150
W148 W149
L1501
C1528
L1511
C1535
Q606
W173
J1001
R421
C710
C1008
C1002 W858
C1001 C1532
W156
Q604
R424
HS402
W089
W141
R1002
W020
R410_1
W088
D603
W143
W142
R1001
IC401
W071
W067 W187
R616
Q405
D410 W021
R418 D402
W183 W068
Q607
12 C4
D403
W090
L1510
W162
C417
W185
W186 W074 W073 W072 W070
W813
R439
CP401
R433
C707
W130
W075
C1007
W136
C1011
C1009
C1004
C1005
C1003
W137
W138
W078 W077 W076
R1009
W144 R649
C422 R422
W079
HS1001
W145
W828
C430
W059
W057
R702
D601
W850 C425
W058
W069
W146
R441
W018
R710
W820
W803
C728
W064 C711
R701
C702
C705
C733
C701
W812
TU001
W133
W060
W131
IC1001
W006
D608
D702 W061
W132
D407 C413_1 D405
S804X
W063
C001_1
W062
CP801A D411
W827
D701 D703
W819 D001
J708
W065
W135
D709
D705 D704
W134
CP101
J704
J703
W001
J701
W007
J702
C426
CD801A
C427
F-2
F-3 R730
Q712
Q711
R736
R516
Q709
R1523
Q605 Q614
R1510 R1529 R1508
Q1001
R705
Q1508
Q1504
R1010 R1011 C1010 C1012
R1506
R1503 C1509
C1513
Q1507
C1508 C1504 C1505 R1502 R1516 R1518
IC1501
R1530 C1531C1517 R1505
C1507
C1503 R1520 C1533
C320
C301
C1519
C1512 C1514 R1512 C1516 R1528 R1504
C322
IC302
W857
W847
C303
C1521
C1515 R1509
Q603
C315
C912
C334 C311
R907
C1506
R1522
R314
C918
C908
C741
R746
C742
R745
C719
R1003
C640 R610 R607
C1523
R609
C005
17
C307 C309 C310 C313
R906
R1004
49
R724
R739
R612 R651 R620
Q902
R657
C607
IC902
C738
C628_1 R635 R641
1
R611
C917
R608 R606 R604 C635 R613
C911
R605
R636
C915
C128
R706
R519 R653 R652 C616 R654 C612
R903
R101
R729 R733 C725
R709
R912
C913
C706 C724 C727 R726 C722 C736
IC 60 1
R634 R629
R145
R110
R106
R103
IC199_1
C737 R734
C439 33
C614 C641
R628
C143
C138
R622
C137
C632
C136
R728 R727 C735
C631
R814
R625
Q103
R632
R128
C624
R617
R511 R618
R150
R136
R127 R142 C149 R134 R141 C126 C124 R143 R129 C129 C140 C142 C135
C141
C115_1
R703
R417
C148
C147
IC101 R135
C102
R708 R725 C619_1
R704
C805 C131 C146 R122 C120 C145 R126
R138
C121 C117
R114
R112 R113
R627
C643 C644 C637
R131
R401
C106 R137 C119 C111
R125
R409_1
R818 C810 R816
C104
R415
R403
R822
R823
R808
R801
Q101
C734 R735
R711
R513 R453
R813 R821 R809 R817 C811
R811 R815 C809 R819
R810
R525
C511
R532 R533
R109
R721
C411
C405
C554
C541
PRINTED CIRCUIT BOARDS MAIN/CRT (CHIP MOUNTED PARTS) SOLDER SIDE
C720
C312
Q901
R1519 C1526
Q1503
R1507
IC1502 IC1503
B_SHORT C416 R407 R1013
R006
IC702 IC701
C002
R404
F-4
A
B
C
D
F
G
H
MICON SCHEMATIC DIAGRAM
ACCESSORY
(MAIN PCB)
8
LED SW Q101 KTC3875S_Y_RTK
1
0
TEST POINT
4.9
R109
0
C108
POWER ON
D109 SLR-342VCT32
Vout
2.7
5.0
KA
B+ 3 GND 2
R120
OS101 RPM7138-H5
1K
CP101
16V 10
TM101 R25-1911
R102
BT002 R03(AB)E_2P_G
47 1/4W
BT001 R03(AB)E_2P_G
270 1/4W
8
E
0
7 R101 C145
0
1K
1K
CLAMP SW Q103 KTC3875S_Y_RTK
AFT
H SYNC
KEY 1
V SYNC
KEY 2
BLUE B
X RAY
GREEN G
5.0
100
REMOCON
RED R
ON_TIMER
BLANK
35 34
9
5.0
10
4.0
OSD_G OSD_R D104
C147
C138
OSD_BLK
4.8
33P CH
R127
0 C131 0
150P CH
0 NC
POWER
15
P FAIL
16
DEGAUSS H
17
X-RAY TEST CNVSS X.IN
MCU_CLOCK
3.9K R128 3.9K
POWER SDA SCL
33P CH
10P CH
R145
2.2K C135
1SS133
100P B
820 C129
100P B R143
5.0 NC
D105
W811
33P CH 820 C126
C149
100P B R142
0
R141
33 32 31 30
SCL1
NC
18
3.5
AUDIO_SW
19
FROM/TO DEFLECTION
SDA1
29
5.0
Y/C_SW
CLOCK_CNT
28
220P CH
11
0
12
220P CH C141
S_IN
13
0
22K 1/4W C140
AUDIO_SW
14
EXT_MUTE
FROM/TO TUNER/STEREO J_AUDIO_OUT_R
R139
5.0 R135
J_AUDIO_OUT_L
4.7K
100 1/4W R140
5.0 R136
R134
SDA
100 1/4W
3 FROM/TO SOUND
10K
5.0
SDA
0
X-RAY
VHOLD
26
CVIN
25
D106
MTZJ5.1B
C106
0.1 B
3.2 NC
RESET
27
SCL 5.0
X-RAY
5.0
C115_1 820P B
2.4
C104
POWER
27P CH
C111
2.0
24
R132
0.1 B
1M
100 1/4W R131
2.0
1K
C122 C119
3
50V 1 KA
220P CH 1.7
FILT
X.OUT
R125
1.0
C121 C117
10
0 21
1
HLF
23
GND
2.3 X101_1 100CTR8005 8MHz
VCC
VSS
22
27P CH
20
C102
DEGAUSS_H
R138
C113
0.001 B
P.FAIL
3
4
SCL
4.7K
2
5.0
4
H_CTL
FROM/TO POWER
5
SW_Y_OUT RESET
C148
0
1SS133
R129 3.9K 0
R119
4
6
OSD_B
2.1
47K
S_IN
7
VD
820 C124
16V 10 KA
C139
FROM/TO AV
R114
6
AUDIO R
HD
5.0
2.2K 2.2
5
SYNC_OUT
0
0.1 B
37
5.0
2.2K R113
GND AUDIO L
7
CLAMP_OFF
100P CH
C137
42 41
0.001 B
R126
C136
SYNC
36
R112 AFT
4
PROTECT
C146
FROM TUNER/STEREO
5
3
I2C_OFF
FROM/TO CHROMA
0.1 B
3.2
BBE SW
12C_OFF
C120
0
0.1 B
0
2
I2C_SDA
1.8 0 R122
R124 10K
VOLUME
40
R110
0 NC
3
TV_MUTE
PROTECT
39
EXT MUTE
4.0
2.2K 1/4W
H_CTL
38
1
AUDIO MUTE
4
CH
R118
5
220P
47K 1/4W
1
I2C_SCL
AT+5V
6
TO SOUND
R150
OEC7090A
5.0
7
C143
R130
MICON IC IC101
2
R146
CH
8
220P
100 1/4W
C142
6
1K 1/4W
SW105 EVQ21505R
220P CH POWER
560 SW104 EVQ21505R
2.7K VOL DOWN
R106
SW102 EVQ21505R
CH DOWN
SW103 EVQ21505R
VOL UP
SW101 EVQ21505R
CH UP
560 R103
173979-7 GND
5.0
0.01
B
47P CH R133 1K 1/4W
C109 TO COMB FILTER
0.1
B C128
Y/C_SW
3
0
0
2
5.0
VCC
8
E0
E1
SCL 0
7
0
1
2
MEMORY IC IC199_1 S-24C16AFJA-TB-01
4
5.0
E2
W822
6
MODE
5.0
SDA
5
VSS
D113
MTZJ5.6B
C114
50V0.47
10K
R137
YK 6.3V 2200
C110
2
F
KA
0.1
0 PCB010 TMC559
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
A
G-1
B
C
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
F
G
H
G-2
A
B
C
D
E
F
G
H
CHROMA SCHEMATIC DIAGRAM (MAIN PCB) 8
8 FROM/TO AV
VIDEO_IN2 V_IN[YUV]
R616
VIDEO_IN1
8.8
120 1/2W
U_IN[YUV]
5.5
R617
Y_IN[YUV]
4.9 AT+5V REG Q607 KTC3203_Y
S804Y
1K
R634 6.8K
R622
C622
7 16V 47 YK
C632
18P CH 3.579545MHz
8.2K C631
KA 1
C627
50V
C624
0.1 B
C630
KA 1
C621
50V
C619_1
50V 0.47 KA
F 0.1
KA 1
C618
50V
C614
0.1 B
C611
50V 1 KA
16V 47 YK
B
C610
C605
C607
0.01
FROM/TO COMB FILTER
16V 47 YK
D602 D601
MTZJ15B
D603
1SS133 MTZJ8.2B
270 1/2W
0.015 B
R603
X602 100CT3R505
7
R618
R657
VIDEO_OUT
330
100
VIDEO_IN3
FROM/TO MICON
C_V_OUT_SW
HI VCC
R OUT
7
8
9
10
11
12
13
14
0
5.5
0
NC
3.8
8.0
8.0
0
8.0
8.0
4.0
4.0
3.3K
0
R651
0
15
32 31 30 29 28 27 26 25 24 23 22 21 20 19
NC(Vcc)
6
18
NC
5
2
ACL
17
NC(GND)
C_APC
MCU 5.7 VREG OUT
CVBS3
NC(GND)
V IN(YUV)
V/C VCC
CVBS2
4
VRAMP CAP
MONITOR OUT
3.6 SW_Y_OUT
6
0 AT+5V
NC 5.0
RESET
3.5 5.0
POWER R627
3.5
SCL 100
3.5
R628 SDA 100
4.9 4.2
5
OSD_BLK
2.9 C637
33P CH
C643
33P
C644
33P CH
OSD_R
2.9
OSD_G
CH
2.9
OSD_B
4.6
VD W805
4.9
HD
4.9
SYNC_OUT
2.1
R629
D608
5.6K
11E1-EIC
4
16
CLAMP_OFF
4.0
NC
33K
R632
KANP C638
16V 10
R625
8.2K
100P CH 1SS133
1SS133 D607
100P CH C646
C647
3.3K D605
1SS133 D606
CH
TO CRT/SVM CP802A B2013H02-7P
100P
R652
C639
16V 1000 YK
C629 0.1 F
R636 1.5K
3.3K
120K
R653
R635
C628_1
0.1 TF
C609
10K
R654
C612 MTZJ12B
100
D604
R609
G IN
INV.FBP OUT
56K
11.3 8.5
NC(GND)
16 B OUT
3
V OUT
4.0
2 AFC FILTER
V PULSE OUT
VRAMP AGC CAP
3.2
W815
CVBS1
49 50 51 52 53
8.7 VREG OUT
15 G OUT
B IN
7.9 8.5
C602
C645
P.CON+5V
16V 100 YK
FROM/TO DEFLECTION
11.3
C606
P.CON 8V REG Q601 KTC3209_Y
P.CON 8V REG Q611 KTC3209_Y 0.33 TF
15 1/2W
7.9
VIDEO LINE OUT
1
UNREG+12V GND
EW OUT
R IN 1 HVCO F/B
DEF VCC
3.9K
330 R608
R606
C635
22P CH
FROM POWER R601
3
4.0 4.0
16V 47 YK
4
1K
R604
390
DELAYDE Y OUT
NC(Vcc)
4.0
FAST BLK
H OUT
R613
CLK CONT
NC
8.7
FAST YUV
SDA CHROMA IC IC601 M61283FP
FBP IN
16V 47 YK
NC
10K
10K
2.3
34 XTAL 3.58
DEF GND2
1.7
3.8
P_CON CONT
48 Y IN(YUV)
R641
2.2
7.3
6dB AMP Q605 KTC3875S_Y_RTK C608
MCU RESET
SCL
50V 1 KA
6dB AMP Q603 KTC3875S_Y_RTK
330 R607
6dBAMP Q614 7.9 7.8 KTA1504S_Y_RTK 7.3 3.8
2.8 NC 3.0 NC 3.0
fsc OUT
PROTECT
Y SW OUT
5.7V VREG OUT
C616
P.CON+8V[B]
R605
R648
TO SOUND
10 1/2W
P.CON+5V
0 33
NC
33 V/C GND
R612
P.CON+8V[B]
0 NC 0
0 3.2 35 34
MCU CLOCK OUT
10K
5
0.01 F
3.2
0 1.9 5.6 2.8 39 38 37 36
47 NC(GND)
0.01 B
C603
TUNER+5V
16V 47 YK
TUNER_VIDEO
C640
0 1.9 5.0 1.2 43 42 41 40
HVCO F/BDEF GND1
100
0 1.2 45 44
LOGIC GND
FROM/TO TUNER/STEREO
5.7
CVBS4
54
R610
VREG VCC
55
5.5
1.9
Y IN(Y/C)
56
5.5 P.CON 5V REG Q604 KTC3209_Y
7.2
8.7
57
50V 1 KA
58
5.0
3.0
5.5
7.2
59
C642 5.0
P.CON 5V REG Q602 KTC3209_Y
NC(GND)
60
3W
0
61
5.6
B
62
12 3W
0.1
63
R649
C615
R602
FSC_OUT
0.01 B
P.CON+8V[A]
C IN(Y/C)
R611
6
C641
64
VIDEO_OUT
0 3.0 47 46
48 2.2
U IN(YUV)
2.7 P.CON+5V REG Q606 KTC3209_Y 5.0 7.2
NC(GND)
P.CON+5V Y_V_OUT_SW
GND
R620
V_OUT 100
R623 100 1/4W
H.OUT
R626 100 1/4W
H_SYNC ABCL
NC
P.CON+8V
1
GND
2
R.OUT
3
G.OUT
4
B.OUT
5
CLAMP_OFF
6
3
7
2
2
PCB010 TMC559
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
A
G-3
B
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
1
DESCRIBED IN PARTS LIST ONLY
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
C
ARE
F
G
H
G-4
A
B
C
D
E
F
G
H
DEFLECTION SCHEMATIC DIAGRAM (MAIN PCB) 8
8 FROM/TO DY V.OUTPUT IC IC401 AN5522 -
THERMAL PROTECTION
25.0 17
4.0
C422
R433
680 1/2W
100V 0.1 TF
12.0
7
680 1/2W
6
R421
C416 5
680 1/2W R429
16
R407
VCC GND 2 3 4 4.0 25.0 2.0 0
1
100P CH
4.7K
R401
+ PUMP UP
V801 A36AKJ13X05
CP401 B06B-DVS
18
AMP
NC L402_1
NC
ELH5L4112N
1.2K
7
6
6
5
5
4
4
3
3
2
2
1
1
9 10 8 6 11
R G B 5 7 1
7
VR401_1 2.2K METAL
V.POSI ADJ
TO CRT/SVM
6
H.OUT
W828
W827
R422
R402 68 1/2W
C411
H_SYNC
GND
PMS 250V 0.27
4.7mH 250V 0909 2.2 YK C418
L401 C410
C420
1.25KV 470P MPP
FB401 115 180
W813
0
W850
2
0.1
HS402 763WAA0216
R428
1
0
0.1
C412
H.OUT Q405 2SD2499(LBOEC1) 115 B405
W4BRH3.5X6X1.0
4
0 26.3
3
17.3
5
T401_1 ETH14Y47AY C403
0
20
50V 22 YK
1K
R403
0.4
17.3 R406
10K
R453
1K
470 1/2W
R409_1
H.DRIVE Q402 KTC3227_Y
C402
500V 22P SL
100V 0.01 MMTS
5
100 1/4W W853
19
C401
1.25KV 0.01 MPP
21
0.001 CH
ABCL
B_SHORT
108.0 105.0 0
W807
+B
0 FBT+B
4
3
560 1/2W
820 1/2W
R418
560 1/2W
100V 0.22 MMTS
C417 1 1/2W
R424
MTZJ30B MTZJ30B R437
C409
GND P.CON+5V
FROM/TO POWER
2
CD803 (CP805) SM1098-009-1A
2KV 0.001 R
50V 10 YK D410 D403
C408 R420
W821
V_OUT
1
C425
W823
5.6 1/2W 50V 1 YK 820
18K +-1%
R416
FROM/TO CHROMA
25V 1000 MHE
33K
1K 1W
2.2 1/2W
D402
11E1-EIC
27K +-1% R415
R417
C406
560P CH R413
C405
R414
6
C407 35V 100 YK
R439
R452_1
D414
D415
11E1-EIC
11E1-EIC
R410_1
D405
220 2W
AU02A-EIC
8.2K 1/2W
0
B+ AFC FORCUS
HEA TER
F
GND
S
FROM/TO CRT SCREEN GND 0 11
8
R430
7
8.1
4
R443 150K 1/2W
E8
C427 100V 0.1 MMTS
3
AU02A-EIC
D407
ABL
GND
TO CRT/SVM MHE
CP801A B2013H02-5P
250V 22
C426
C413_1
D411 AU02A-EIC
35V 1000 YK
R441 15K +-1% C430
C439
0.001 B
4.7K 1/4W +-1%
R426
D406
MTZJ5.6B
2
18K 1/4W +-1%
100V 22 YK
R436
W844
6.8 2W
R438
FROM/TO MICON
X-RAY
10
0.1 5 NC
3
H_CTL
9
HV
E180
150K 1/2W
100
MTZJ5.1B
R432
D404
R404
2
8
ANORD
E12 0.2 4 NC E27 2.0 3
H+B 0.27 1W
1 6
5
3214035F
COL
180V
1
NC
NC
2
NC
NC
3
GND
4
HEATER
5
2
PCB010 TMC559
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
G-5
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
B
C
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
ARE
DESCRIBED IN PARTS LIST ONLY
D
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
E
F
G
1
H
G-6
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM (MAIN PCB)
8
RELAY DRIVE Q504 KTC3198
R515
0
10K 1/4W
150 1/4W
11
1/2W
12
0
1N4937
D513 10K 1/4W R507
10K
R535
3.9K 1/4W
82K 1/4W
4
R524
100 1/4W
240.0 NC
P.FAIL 3.3K 1/4W
X-RAY DEGAUSS_H POWER GND
20 C520
0 500V
138.9
13
3
0.001 B
P.CON+12V SW. Q508 KTA1271_Y
26 D512
GND1
0
14 NC
2
12.9 R511
21DQ09N
0
0.001 CH
C550 16V 100
YK
12.8 R512
C527
16V 2200 YK
C523
D520
S805X
12.9
22K
1SS133
IS THE LIVE CONNECTION
R547
D525
15
250V 0.0022 KX
CAUTION:
C508_1
R513
C521
FROM/TO MICON R546
159.0
1
D508
D528
1SS133
25V 1000 YK
C501 P2 5
1N4937
R543_1
9 10
D506
1K
47 YK 25V
C509
0.056 B
C541
220P CH
C511
1SS133
4
100 1/4W
25 D511
P1
3
2 270
R533
8 7
100 1/4W MTZJ5.6B
R554
100K 1/2W
D524
81290914
R510
VR502 22K
R506
6.8K 1/4W
UNREG+12V GND
R508
MTZJ18B
1.5
1.5K
3
+B ADJ
TO CHROMA HS501 763WAA0244
46 NC 6
R532
MTZJ3.9B
R553
FEED BACK SWITCHING Q507 KTC3198
6.8K 1/2W
W817
9.7
9.7
5
TO TUNER/STEREO
15K
R545
D509
10K
0
GND
141.6
C554
R516
0
MMTS
16.3 1
10.7
100V 0.047
T501_1
FEED BACK IC504 LTV-817M-VB
115.2
0.8 STAND BY SW. Q509 KTC3198
3
1K 1/2W
1SS133
114.7
P.CON+B
C504
0.22 1W
0
GND
115.1
STAND BY SW. Q505 2SC2909
0.68 2W
50V 2.2 YK
R542
270 1/4W D507
330 2W 1.5 C524
SWITCHING Q514 KTC3203_Y R544
D510 FE201-6L49
FBT+B
C512
500V 0.001 B
2KV 0.001 R
C535
4
0 S
R502
R527
B504 W5RH3.5X5X1.0
160V 100 YXF
SWITCHING Q502 2SK3326(2) G 5.3 5.3
159.4 D
5.7
1SS133
D514
R539
1.2M 1/4W
R540
1.2M 1/4W
B501 BL02RN1-R62
6.3
115.5
R525
D504
D523
ECQUL
MTZJ18B
2KV 0.0015 R
6
+B
+B SW. Q503 2SA1371
C539
47K 1/4W
W825
FROM/TO DEFLECTION H+B
R536
6.3A 125V
0.022 B
38 CURRENT DET. Q512 2SA1624 115.7
C517
W801
5
1SS133
100K 1/4W 115.4
50V 10 YK
6.3A125V FH501 FH502 EYF-52BC EYF-52BC 6.3A125Vor51MS063L
GND SOUND_GND
R537
1/4W
P.CON+12V
D517
R503 10K
MTZJ12B
BLACK
2
SOUND+B 1 3W
S805Y
100 1/4W
BLACK
1
1
F501
4
1
0.22 1W
R517_1
W806
R505
WHITE
3
1 7W
C503
2KV 2KV 0.001 R 0.001 R RM11C-EIC
WHITE
C502
C506_1
2
2
CP501 A3963WV2-3PD
BLADE WIDE
AC120V_60Hz CD501_1 09619901
CP508 003P-2100
275V 0.22 ECQUL
1
R520
ZPB45BL3R0A
6
1.5M 1/2W
TH501_1
COIL,LINE FILTER L501 1R5A123F28Y
R541_1
C507
CP507 003P-2100 1
275V 0.1
2
R501
200V 330 UP
D501
1
D502
R500
CP502 A1561WV2-2P
C505_1
1 2
4
TO SOUND
D505
RM11C-EIC
3 DEGAUSS COIL L503 8R140023
7 B
30DF6-FC
RM11C-EIC
1 2.7M 1/2W +-10%
2
C516 500V 0.001
D503
RY501 ALKS321
RM11C-EIC
C513_1
7
250V 0.001 KX
0
C519_1
10.9
250V 0.001 KX
D516 1SS133
8
0.7
TO AV
R519 10K
P.CON+12V
0
GND FROM/TO COMB FILTER GND
2
2 PCB010 TMC559
6.3A 125V
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, 6.3A 125V(F501)
1
REPLACE ONLY WITH THE SAME TYPE FUSE
A
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
ARE
DESCRIBED IN PARTS LIST ONLY
UNE PROTECTION CONTINUE LES RISQUES D’INCEIE ATTENTION:POUR N’UTOLISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501)
G-7
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
B
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
D
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
E
F
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
G
1
H
G-8
A
B
C
D
E
F
G
H
SOUND SCHEMATIC DIAGRAM (MAIN PCB)
YK C319
SW_AUDIO_L
29
L301
NC 27
0
0 NC
4.0
W857
C317
C313
50V 10 YK
4.0 15
BD
VD L ONT
NC 21 0
NC 20 0
NC
16
Balance /MUTE
6
R OUT SDA SCL 19 18 17 4.0 3.5 3.5
NC
R303 100 1/4W R304
0.1 B
C311
5
100 1/4W
C320
0.01 B
C303
C306
2.9 14
+
NC
100uH 0305 16V 100 YK
2.0
+
RB RT BLD TD 25 24 23 22 4.0 4.4 3.0 2.0
P.CON+8V[B]
FROM/TO COMBI FILTER
0.01 B
C310 BB 26
NC 13 NC
W831
56P CH
C308
50V 10 YK
C302 FROM CHROMA
4.0
LB
0
56P CH C322
4.5
NC 28
LT
NC 12 NC
W832
W847
7.9
C305
2.3
Vref
30
0 11
Volume 2.2K Control
Control
R IN
31
4.0 10
C316
32
PF3
4.0
9 GND
C312
MODE control VCC
PF2
0
8 PF4
Tone
SURR
+
7
50V 10 YK
L IN
3.9
6
C314
AGC
5 NC
50V 10 YK
PF1
4 NC
0.01 B
3
0.039 B 3.9
3.9
1 B
2
NC
0
0.033 B
50V 10 YK
1
AGC
NC
0
3.0
C334
6
1.7
50V 10 YK
TONE CONTROL IC IC302 AN5891SA-E1V
3.9
C309
50V 10 YK
C301
7 C304
1/4W
2.7K 1/4W
0.033 B
2.7K
R301
22 SW_AUDIO_R
5
8
50V 10
R302
23
0.1 B
C315 C307
FROM TUNER/STEREO
7
0.015 B
R314
220K C333
50V 10 YK
8
GND FROM/TO MICON SDA SCL
4
4 SOUND AMP IC IC1001 AN5276
TV_MUTE
+ -
+ ATT.
+
+
RIPPLE FILTER CH1 CH2 NC GND RF IN IN 1 2 3 4 5 0 NC 0.2 16.0 0 0.2
FROM POWER
CD1001 25
ATT.CONT.
24
VOL 6 0
CH2 OUT
STAND CH1 GND VCC -BY OUT 9 10 11 12 0 16.5 12.7 0.7
MUTE 7 8 0.7 3.7
SOUND+B
3
GND
CU146901
CP1001 A2502WV2-4P
VOL
4
4
3
3
2
2
1
1
SPEAKER SP1001 810-47-171 8 OHM 5W (L) 2.5W SPEAKER SP1002 810-47-171 8 OHM 5W 2.5W
W803
P.CON+12V
15K
C1002
15K
C1004
25V 1000 YK
25V 1000 YK
50V 10 YK C1009
25V 1000 YK
C1003
0.0039 B
6.8K C1010
R1010
6.8K
0.0039 B R1011
C1012
R1013
HEADPHONE JACK J1001 MSJ-2000
R1009
C1007
R1002 50V 22 YK
0
7
26 50V 2.2 YK
MUTE 10K 1/4W Q1001 KRC111SRTK 3.6 0
C1008
C1005
220P B
25V 220 YK
C1011
10K
2
3
50V 10 YK
R1004
W858
(R)
C1001
R1003
SOUND_GND
2
6 2
R1001 270 1/2W
27
3
HS1001 763WAA0215
270 1/2W
4 5 1 PCB010 TMC559
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
G-9
B
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
DESCRIBED IN PARTS LIST ONLY
C
D
E
ARE
CAUTION: DIGITAL TRANSISTOR
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
1
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
F
G
H
G-10
A
B
C
D
E
F
G
H
TUNER/STEREO SCHEMATIC DIAGRAM (MAIN PCB)
8
FROM/TO CHROMA 21
18
NC
7
20
17
VIDEO OUT
16 IF OUT
15 BT
14 SIF OUT
AUDIO OUT 13
12 AFT
8 (X’TAL)
7
6
MB 4
5
MB 3
2
1
11 SDA
9 (ADRESS)
115-V-K015AR B
19
10 SCL
TU001
8
NC
NC
NC
NC
NC NC
NC
NC
TUNER+5V
NC
7
TUNER_VIDEO
W812
D001
MTZJ33B
0.1
C005
100
100 YK 6.3V
C001_1
F
P.CON+5V
R006
C002
0.1 B
P.CON+8V[B]
6
W819
W820
6
FROM POWER R001 P.CON+B 68K 1/2W R002 68K
GND
1/2W TO MICON
5
5
AFT
R905
R904 C901
2.3 BUFFER Q901 KTA1504S_Y_RTK 0
56K 1/4W
3.2
J_AUDIO_OUT_L
220 1/4W
SDA
R902
SCL
56K 1/4W
R901
220 1/4W
FROM/TO MICON
50V
1 KA
J_AUDIO_OUT_R
50V 10 YK
C919
39K
W829
50V 1 KA R906
39K
R903
BUFFER Q902 0 KTA1504S_Y_RTK
4 330
C902
2.3
R912
3.2
W830
4
TO SOUND L901 SW_AUDIO_L 0.1 B
C917
Filter Noise
Filter SAP Demod SAP
Expand Spectral
RMS Det Spectral
Det Noise
2.4
11 0.4
12 2.3
3.4
2 10V 100 YK
2.4
10
0.1 B
9
C916
8
C918
5.1
13
Filter Spectral
0.1 B
0.4
Vcc
Filter Stereo
3
3.7
Det SAP
VCA Input
50V 3.3 KA
2.2
7
14
Det Pilot
C915
dbx De-Emph
6
15
2.6
Filter Wide Band
C914
2.2
C905
50V 4.7 KA
220K C903
R907
AUDIO_IN3[L]
5
3.6
50V 0.33 KA
C904
AUDIO_IN3[R]
L+R Demod
C910
2.3
L-R Demod
0.022 B
2.3
Cancel Pilot
L-R Filter
50V 10 YK
0
AUDIO_IN1/2[L]
4
16
3.7
St.PLL
fH.2fH Trap Filter
50V 4.7 KA
AUDIO_IN1/2[R]
3
17
0
GND
L+R Filter
RMS Det Wide Band
2.3 2
18
5.0
ZAP IIC Decoder
DAC
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
1
19
5.0
C912
20
0
0.022 B
NC
Matrix
J_AUDIO_OUT_R
2
21
OUT SW
AGC
2.3
C908
J_AUDIO_OUT_L
22
2.3
C907
FROM/TO AV
23
2.3
50V 4.7 KA
SOUND DECORDER IC IC902 AN5829S
24
2.3
0.1 B
C911
3
100uH 0305
0.047 B C913
SW_AUDIO_R
PCB010 TMC559
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
G-11
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
ARE
C
D
E
1
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
DESCRIBED IN PARTS LIST ONLY
F
G
H
G-12
A
B
C
D
E
F
G
H
AV SCHEMATIC DIAGRAM (MAIN PCB) FROM/TO CHROMA
2
E
H1
28 V_IN[YUV]
S804X
75 H1
5
E
VIDEO_IN2
R736
MTZJ12B
75 D703
MTZJ12B R730
D702
MTZJ12B
75
VIDEO_OUT
D701
R725
29
4
Y_IN[YUV]
H2
3
U_IN[YUV]
A/V_OUT(REAR) J708 MSP-213V2-432_PBSN
VIDEO_IN1
1K
270
R709
R705
3.3K
0
0.2
R703 R711 0.1
2.2K
1K
BUFFER Q709 KTA1504S_Y_RTK
MUTE Q711 KTC3875S_Y_RTK
68
E
1 E
R721
0.2
0 R710
0.1
1K 1/4W
5
C728 16V 470 YK
6
KANP
R706
47
16V 10 KA
1K
5.2
4.6 3.3K
C708 C710
16V 100 YK
22 1/4W
16V
R704
7
3
C707 16V 10 KA
R702
R708
2
C711
4
VIDEO_IN3
H1 NC H1 H2
7
8
YUV_IN(REAR) J704 MSP-213V1-652_PBSN 1
8
MUTE Q712 KTC3875S_Y_RTK 0
6
6
R734 R728
1K
E
1
2
E
1K 0.0056 B
0.0056 B C735
C737
4 1K
E
1 E
4.5
R726
1K B
4.5
0.0056 B 1
5
2
6
3 4
MTZJ6.2B
Vin2
75
Vcc
0
D709
GND
0.1 B
R735
V.OUT
6
Vin1
5
SW1
4
C734 4.5
4
12.7
1
3.7
2
0
3
AUDIO SW(L) IC IC702 MM1501XNRE
S_IN
0.0056 B C736
KA R739
FROM/TO MICON
22
75
16V
AUDIO_SW
C738
S-JACK J702 YKF51-5503
C733
4
EXT_MUTE
MTZJ12B
75 D704
6
Vin2
1
R729
12.7
1/4W C705
AUDIO_IN3[R]
Vcc
0
C722
F
22
5
R701
16V 10 KA
GND
R733 B
0.1
AUDIO_IN1/2[L]
16V 10 KA
16V 220 YK C706
C701
V.OUT
4
3.7
2
C702 AUDIO_IN1/2[R]
3
1
2
C725
4.5
5
3
Vin1
H1 NC H1 H2
SW1
6
0
J_AUDIO_OUT_L
1
J_AUDIO_OUT_R
AUDIO_IN3[L]
MTZJ12B
LINE1(REAR) J701 MSP-213V2-432_PBSN
AUDIO SW(R) IC IC701 MM1501XNRE
5
5
FROM/TO TUNER/STEREO
75 D705
R727
6
1 B
5
C724
3
1 B
H1 NC H1 H2
C727
4
LINE2(REAR) J703 MSP-213V2-432_PBSN
3
3
FRONT-VIDEO J705 HTJ-032-03AY
GND
1
PCB010 TMC559
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
E
3 0.0056 C742
LINE3_A_IN_R
E
1K
1
1 B P.CON+12V
2
3
R746
NC
C720
0.0056 B
FROM POWER
NC H
FRONT-AUDIO.R J707 HTJ-032-03AR
2
D706
C741
2
2
LINE3_A_IN_L
H
1K B
R745
1 B
FRONT-AUDIO.L J706 HTJ-032-03AW
MTZJ12B
C719
100
R724
S_VIDEO_IN[C]
G-13
E
H
2
S_VIDEO_IN[Y]
1
NC
3
TO COMB FILTER
B
C
D
E
F
1
G
H
G-14
A
B
C
D
E
F
G
H
CRT SCHEMATIC DIAGRAM (CRT PCB)
8
8
7
7
CRT BLOCK (W/O SVM)
FROM DEFLECTION
1
CP806 005P-2100
FROM DEFLECTION
180V NC
NC
3
NC
NC
4
GND
5
HEATER
W802 C802
1 2
2KV 0.001
6
B
CP801B B2013H02-5P
6
FOCUS
R802
6 7
7.4 D801
3.2 2.7
D810 R823
CLAMP OFF
1SS133
100 (14F GREEN)
NC
470P B
R809 4.7K
R817 R813
220
6.9
3.2 D811
2.7
C810
14F:GREEN OUT 27":RED OUT R806
1SS133 38
390
GREEN/RED OUT Q803 98.4 KTC3199_Y
R822 100 (14F RED)
C811
15K 2W 123.0
R807
GREEN/RED OUT Q805 KTC4217 125.0 7.4 D802
R818
7.0
15K 2W
14F:RED OUT 27":GREEN OUT
0
0 R804
470P B
R816
220
1SS133 39
3.2
100 D812 1SS133
4.7K
15K 2W
8
3
9
1 C809
R819 220
7
FROM BRAIDED WIRE
128.0
7.4
2.7
560P B R815
R811
BLUE OUT Q806 KTC4217
6
4 96.4
7.0 D803
BLUE OUT C804
4
95.4
220
R821
390 R810
4.7K BLUE OUT Q802 KTC3199_Y
5
6.4
2.7K 1/4W
R805
1SS133
390
1 CP803 2 A2361WV2-2P
F
0
YK
R814
250V 10
1SS133
5
2.7K 1/4W
99.6
B.OUT
2.7K 1/4W
R803
96.4
G.OUT
5
220
R.OUT
4
R801
3
37
RED/GREEN OUT Q804 KTC4217
220
GND
C805
CLAMP
2
R808
5
1
RED/GREEN OUT Q801 100.6 KTC3199_Y
0.1
CP802B B2013H02-7P
B
FROM CHROMA
4
CRT SOCKET J801_2 ISMS01S 14F MINI NECK C801 100P B R824 100 1/2W TCC421 PCB110
3
3
2
2
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
G-15
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY
C
D
E
1
N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
F
G
H
G-16
A
B
C
D
E
F
G
H
COMB/FILTER SCHEMATIC DIAGRAM (MAIN PCB)
8
8
7
7
L1511
2.0
6
C1531
BUFFER Q1508 KTC3875S_Y_RTK
0.01 B
C1528
7.9 2.5
16V 100 YK
15uH 0305
6
C1535
R1530
R1505
FROM AV
S_VIDEO_IN[C]
6.8K
100
R1503
KA
470
16V 10
L1505 15uH 0305
S_VIDEO_IN[Y]
VIDEO SW(Y) IC IC1502 MM1501XNRE
1.0
0 4.5
6
4.5
Vin1
SW1
5
B
GND
V.OUT
4
0.1 1K
R1507
3.3K
R1506
C1519
Vin2
Vcc
0 4.4 7.9
Y/C_SW
VIDEO SW(C) IC IC1503 MM1501XNRE
Vcc
1 2
18 17
Vin2
7.9
C_V_OUT_SW L1501 P.CON+8V[A]
15
C1514 L1508
L1510
47K
FSC_OUT
27K
L1512
R1522
22uH
1K
VIDEO_OUT C1533
R1520
1.6
1.2K
16V 47 YK
22P CH
R1518
C1530 2.2
24K
2
5.0
R1519
R1516
BUFFER Q1507 KTC3875S_Y_RTK
1K
0.01 B
C1526
6.3V 100 YK
0.1 B
3
100
C1525
GND
0305
R1523
47K
0 GND
5.0 2.4 BUFFER Q1504 KTC3875S_Y_RTK 2.0 R1508
PHASE DET FSC_IN
0
11
0.9
0.1 B C1515
R1510
RD
6.3V 100 YK
13
SAND CASTLE
C1520
AFC
12
DVCC
82K C1516 10K R1504 C1518 0.1 B 9.5 C1512 8.2K 50V 1 KA
R1509
100uH
15uH 0305
P.CON+5V
R1529
3.6
3.9K
0.1 B
C1521
R1528
0.1 B
14
2.9
16V 100 YK
YIN1
F
AVCC
0
C1532
GND
C1523
GND
4
100uH 0305
10
4 6 8
4.5
4.4
0.1
YOUT
0.1 B C1507 2.1
9
V.OUT
16
YIN2
C1506 4.0
0.1 B
GND
3.4
4.9 5
0.1 B
OUTSEL
0
7
0.1 B
C1503
6.3V 100 YK
220uH 0305
INSEL
4.9
L1503 C1502
220uH 0305
3
C1508
L1502
6.3V 100 YK
C1501
1 B
0
0
4.2 3
C1505
SW1
3
4.9 2
100
R1502
0.1 B
COUT
Vin1
Y_V_OUT_SW
2.4 CIN
FROM/TO CHROMA 0
6
2.6 1
C1504
4.5
5
COMB FILTER IC IC1501 LA76600M-TLM
4
4
5
FROM MICON 1
BUFFER Q1503 KTC3875S_Y_RTK
2
W848
0.1 B
1K
3
1.0
C1517
C1510
5.0
C1513
100P CH
5
6.3V 100 YK
C1509
0.01 B
R1512
FROM/TO POWER
2
GND
FROM/TO SOUND GND PCB010 TMC559
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
A
G-17
B
C
D
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
E
F
1
G
H
G-18
WAVEFORMS MICON
SOUND
100µs
5ms
1V
5V
1
5µs
1ms 50mV
17
22
1ms 200mV
5ms 10V
1V
2
18
50µs
20µs
1V
50V
3
50µs
23
1ms 100mV
24
19
20µs 2V
1V
4
1ms 100mV
25
20
DEFLECTION 5ms 200mV
16
20µs 200V
1ms 5V
21
26
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
1ms
20µs
5V
50V
27
39
AV 20µs 200mV
28
20µs 200mV
29
CRT 20µs 50V
37
20µs 50V
38
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
111 202
105
111
202 202
203 204
110 201
103 102
104
202
201 201
PCB110 (CRT PCB ASS'Y)
106
109 108 201
206 206 208 208
205
207 101I 101H 101E
205 205
101F 101C 101G 101E
101I 107
101B 101D 101A
101 I-1
207 PCB010 (MAIN PCB ASS'Y)
111
MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N
Reference No.
Description
101 101A 101B 101C 101D 101E 101F 101G 101H 101I
AD302277 AD302278 AD302279 AD302280 AE000539 AE000540 AE000541 AD302009 AD302283 AE000174
A3M801J720 701WPJC097 711WPA0187 713WPA0274 723549A016 735WPBA657 735WPJA773 735WPA0728 735WPA0748 800WQ00056
CABINET,FRONT ASSY CABINET,FRONT PLATE,FRONT GLASS,LED BADGE,GRAND BUTTON,FRAME BUTTON,POWER STOPPER,BUTTON STOPPER,BUTTON 2 FELT SHEET
102
AE000538
A3M801J740
CABINET,BACK ASSY
103 104 105 106 107 108 109
AE000091 AE000006 AD302284 AD302285 AD300132 BZ710009 BZ710260
722000A023 7220001119 722549A164 723000C155 7230006818 741WUA0019 899HV3T000
SHEET,HWC SHEET,CSA WARNING SHEET,RATING POP LABEL SHEET,CAUTION SPRING,EARTH HOLDER,ANODE WIRE
110 111
AD301154 AD300134
726000A031 800WQ00039
SHEET,CRT NO. FELT SHEET
201 202 203 204 205 206 207 208
BZ710383 BZ710035 BZ710262 BZ710031 BZ710030 BZ710239 BZ710019 BZ710018
8121J50C04 8117540A64 8117540A04 8110630A04 8110630804 8109I30A04 8109630802 8107630804
SCREW,TAPPING(B0) GW15 SCREW,TAPPING(B0) TRUSS SCREW,TAPPING(B0) TRUSS SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(S) BRAZIER
-----------------------
AE000234 AE000093 AD302286 AD302287 AD302288 AE000011 AD302020 AD300022 AD300023 AE000235 AD301213
723000C243 791WHA0090 792WHA0446 792WHA0447 793WCDB636 7230007398 A3M701Z975 J3I70417 J3I70436 J3M70101B JA4UD300
SHEET,BAR CODE LAMIFILM,BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX SECURITY TAG (FOR CANADA ONLY) INSTRUCTION BOOK KIT REGISTRATION CARD ESP CARD INSTRUCTION BOOK POLYBAG,INSTRUCTION(RED CAUTION)
J1-1
5x30 4x16 4x10 3x10 3x8 3x10 3x8 3x8
ELECTRICAL REPLACEMENT PARTS LIST Location No.
TSB P/N
Reference No.
Description RESISTORS
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
R402 R410 R426 R436 R438 R439 R441 R452 R500 R501 R502 R506 R517 R520 R527 R541 R542 R602 R649 R803 R805 R807
BZ210021 BZ210087 BZ210030 BZ210023 BZ210232 BZ210003 AD300037 AD301143 BZ210080 AD301596 AD301016 BZ210162 BZ210191 BZ210206 BZ210149 BZ210190 BZ210063 AD301975 AD302271 BZ210026 BZ210026 BZ210026
R65582680J R3X18A221J R4X5T4472F R4X5T4183F R6558A6R8J R3K181102J R4X5T6153F R3X181R27J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R3X28B010J R002T2155J R3X18AR68J R63581R22J R3X181R22J R3X28B120J R3X28B5R6J R3X18A153J R3X18A153J R3X18A153J
R,FUSE R,METAL OXIDE R,METAL R,METAL R,FUSE R,METAL R,METAL R,METAL OXIDE RC R,CEMENT R,METAL OXIDE RC R,METAL RC R,METAL OXIDE R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE
C147 C148 C149 C408 C412 C413 C418 C420 C425 C426 C430 C501 C502 C503 C504 C505 C506 C507 C508 C513 C517 C519 C521 C527 C535 C639 C646 C647 C802 C1003 C1004 C1009
AE000565 AE000565 AE000565 BZ110032 AD301318 AD301977 AD301144 BZ110218 BZ110202 AD300061 BZ110195 BZ110053 BZ110202 BZ110202 AD301729 BZ110025 BZ110035 AD301635 AD301108 AD301026 BZ110191 AD301026 AD300060 BZ110119 BZ110202 AD301321 AD301321 AD301321 AD300078 BZ110053 BZ110053 BZ110053
CS0RCH4L1J CS0RCH4L1J CS0RCH4L1J E5EZF3102M P4N8FJ471J E0ELF4102M P4J7F3274J P4N8FJ103H C0PLRR713K E5EZFD220M E02LU8220M E02LF3102M C0PLRR713K C0PLRR713K E02LU52R2M P2122B224M P2122B104M E51CGC331M CD39E0MH3M CD39E0M13M C03L0R7E3K CD39E0M13M E62NFB101M E02LF2222M C0PLRR713K CQG0CH412J CQG0CH412J CQG0CH412J C0JBB0713K E02LF3102M E02LF3102M E02LF3102M
CC CC CC CE CMPP CE CMPP CMPP CC CE CE CE CC CC CE CMP CMP CE CC CC CC CC CE CE CC CC CC CC CC CE CE CE
D001 D104 D105 D106 D109 D113 D402 D403 D404 D405 D406 D407 D410 D411 D414
BZ410037 BZ410006 BZ410006 BZ410020 BZ410054 BZ410021 BZ410043 BZ410019 BZ410020 BZ410063 BZ410021 BZ410063 BZ410019 BZ410063 BZ410043
D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D97U05R61B D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D97U03001B D2WTAU02A0 D2WT011E10
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON
68 OHM 1/2W 220 OHM 2W 4.7K OHM 1/4W 18K OHM 1/4W 6.8 OHM 2W 1K OHM 1W 15K OHM 1/6W 0.27 OHM 1W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 1 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 0.22 OHM 1W 0.22 OHM 1W 12 OHM 3W 5.6 OHM 3W 15K OHM 2W 15K OHM 2W 15K OHM 2W
CAPACITORS
! ! ! ! !
! ! ! ! ! ! ! ! !
33 PF 50V CH 33 PF 50V CH 33 PF 50V CH 1000 UF 25V 470 PF 1.25KV 1000 UF 35V 0.27 UF 250V PMS 0.01 UF 1.25KV 0.001 UF 2KV R 22 UF 250V 22 UF 100V 1000 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 330 UF 200V 0.0022UF 250V 0.001 UF 250V 0.0015UF 2KV R 0.001 UF 250V 100 UF 160V 2200 UF 16V 0.001 UF 2KV R 100 PF 50V CH 100 PF 50V CH 100 PF 50V CH 0.001 UF 2KV B 1000 UF 25V 1000 UF 25V 1000 UF 25V
DIODES
! ! ! !
J2-1
MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 MTZJ5.6B T-77 11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC MTZJ30B T-77 AU02A-EIC 11E1-EIC
ELECTRICAL REPLACEMENT PARTS LIST Location No.
TSB P/N
Reference No.
Description DIODES
D415 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D516 D517 D520 D523 D524 D525 D528 D601 D602 D603 D604 D605 D606 D607 D608 D701 D702 D703 D704 D705 D706 D709 D801 D802 D803 D810 D811 D812
BZ410043 BZ410062 BZ410062 BZ410062 BZ410062 AD300076 AD300731 BZ410006 BZ410064 AD300671 AD301980 AD300731 BZ410010 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD300671 BZ410006 AD300070 BZ410021 BZ410006 BZ410058 AD300670 AD300070 BZ410006 BZ410006 BZ410006 BZ410043 AD300070 AD300070 AD300070 AD300070 AD300070 AD300070 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006
D2WT011E10 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F30DF60 D2WXN49370 D1VT001330 D97U03R91B D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01201B D97U05R61B D1VT001330 D97U08R21B D97U01501B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330
DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON
IC101 IC199 IC302 ! IC401 ! IC504 IC601 IC701 IC702 IC902 ! IC1001 IC1501 IC1502 IC1503
AD301981 AD302274 AD301983 BZ611053 BZ410088 AD301984 AD301988 AD301988 AD300059 AD300056 AD301029 AD301988 AD301988
I56F07090A A3M801J015 I01FF58910 I01TD55220 0002E00610 I06FC12830 I0UF015010 I0UF015010 I01FF58290 I0FSP52760 I03FE76600 I0UF015010 I0UF015010
IC IC IC IC PHOTO COUPLER IC IC IC IC IC IC IC IC
Q101 Q103 Q402 Q405 Q502 Q503 Q504 Q505 Q507 Q508 Q509 Q512 Q514
BZ510109 BZ510109 BZ510097 BZ510040 BZ510098 BZ510005 BZ510069 BZ510011 BZ510069 BZ510077 BZ510069 BZ510004 BZ510070
TCAA3875SY TCAA3875SY TCAT03227Y TDUU024990 T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TAAT012714 TCATC31980 TA3T016240 TCAT032034
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON
! ! ! ! ! !
! ! !
!
11E1-EIC RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30DF6-FC 1N4937 1SS133T-77 MTZJ3.9B T-77 MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ12B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ15B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77
ICS OEC7090A S-24C16AFJA-TB-01 AN5891SA-E1V AN5522 LTV-817M-VB M61283FP MM1501XNRE MM1501XNRE AN5829S AN5276 LA76600M-TLM MM1501XNRE MM1501XNRE
TRANSISTORS
! ! ! ! ! ! ! ! !
J2-2
KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SD2499(LB0EC1) 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) KTA1271_Y-AT KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT
ELECTRICAL REPLACEMENT PARTS LIST Location No.
TSB P/N
Reference No.
Description TRANSISTORS
Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q611 Q614 Q709 Q711 Q712 Q801 Q802 Q803 Q804 Q805 Q806 Q901 Q902 Q1001 Q1503 Q1504 Q1507 Q1508
BZ510105 BZ510105 BZ510109 BZ510105 BZ510109 BZ510105 BZ510070 BZ510105 BZ510108 BZ510108 BZ510109 BZ510109 AD301032 AD301032 AD301032 BZ510091 BZ510091 BZ510091 BZ510108 BZ510108 BZ510068 BZ510109 BZ510109 BZ510109 BZ510109
TCAT03209Y TCAT03209Y TCAA3875SY TCAT03209Y TCAA3875SY TCAT03209Y TCAT032034 TCAT03209Y TAAA1504SY TAAA1504SY TCAA3875SY TCAA3875SY TCATC3199Y TCATC3199Y TCATC3199Y TCA0042170 TCA0042170 TCA0042170 TAAA1504SY TAAA1504SY TNAAJ05003 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY
L301 L401 L402 ! L501 ! L503 L901 L1501 L1502 L1503 L1505 L1508 L1510 L1511 L1512 T401 ! T501
BZ310041 BZ310004 BZ310013 AD300119 BZ310116 BZ310041 BZ310041 AD301417 AD301417 AD300613 BZ310041 AD300613 AD300613 AD301608 BZ310172 AD301146
02167F101J 021679472K 0221000013 029T000097 028R140023 02167F101J 02167F101J 02167F221J 02167F221J 02167F150J 02167F101J 02167F150J 02167F150J 0216A6220J 045013003J 0481290914
COIL COIL COIL,LINEARITY COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
J701 J702 J703 J704 J705 J706 J707 J708 ! J801 J1001
AD301038 AD300108 AD301038 AD301037 AD300110 AD300111 AD300112 AD301038 AD301147 BZ614361
060J431019 063Q700002 060J431019 060J411024 060G401047 060G401046 060G401039 060J431019 066F120018 060J131015
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY TUBE HEADPHONE JACK
SW101 SW102 SW103 SW104 SW105
BZ612010 BZ612010 BZ612010 BZ612010 BZ612010
0504101T34 0504101T34 0504101T34 0504101T34 0504101T34
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT
VR401 VR502
BZ210218 BZ210101
V1K63H3BTE V1163H4BTC
PCB010 PCB110
AD302275 AD302276
A3M801J010 A3M801J110
B405 B501 B504 BT001 BT002
BZ310129 BZ310045 BZ310121 AE000012 AE000012
024HT03564 024AT03481 024HT03553 1412004008 1412004008
! ! ! ! ! !
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON
KTC3209_Y-AT KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTA1504S_Y_RTK KTA1504S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTA1504S_Y_RTK KTA1504S_Y_RTK KRC111SRTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK
COILS &TRANSFORMERS 100 UH 4.7 MH ELH5L4112N 1R5A123F28Y 8R140023 100 UH 100 UH 220 UH 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH ETH14Y47AY 81290914
JACKS MSP-213V2-432 PBSN YKF51-5503 MSP-213V2-432 PBSN MSP-213V1-652 PBSN HTJ-032-03AY HTJ-032-03AW HTJ-032-03AR MSP-213V2-432 PBSN ISMS01S MSJ-2000
SWITCHES EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R
VARIABLE RESISTORS VOLUME,SEMI FIXED VOLUME,SEMI FIXED
NVG6TLTAB222 EVNCYAA03BE4
P.C.BOARD ASSEMBLIES PCB ASS'Y PCB ASS'Y
TMC559B TCC421B
MISCELLANEOUS CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN
J2-3
W4BRH3.5X6X1.0 BL02RN1-R62T2 W5RH3.5X5X1.0 R03(AB)E_2P_G R03(AB)E_2P_G
ELECTRICAL REPLACEMENT PARTS LIST Location No.
TSB P/N
Reference No.
Description MISCELLANEOUS
! CD501 CD801 CD802 CD803 CP101 ! CP401 ! CP501 ! CP502 CP507 CP508 CP803 CP806 CD1001 CP1001 CP801A CP801B CP802A CP802B EL001 EL002 ! F501 ! FB401 FH501 FH502 OS101 ! RY501 SP1001 SP1002 ! TH501 TM101 ! TU001 ! V801 X101 X602
AE000566 AE000567 AE000568 BZ614175 BZ614102 AD300095 BZ614176 AD300687 BZ614444 BZ614444 BZ614269 BZ614058 AE000569 AD301045 BZ614276 BZ614276 AD301997 AD301997 BZ614044 BZ614043 AD301046 AD301151 BZ614005 BZ614005 AD301048 AD300114 BZ614029 BZ614029 BZ410079 AD302001 AE000273 AD301152 AD302002 AD302003
1209619901 WCL6826038 WEL6836038 06CU82039A 0694270139 069X460029 069S320419 069S420110 069D01001A 069D01001A 069S320010 069W010010 06CU146901 069S140419 067U005049 067U005049 067U007029 067U007029 124120301A 124116281A 081PC6R305 043214035F 06710T0006 06710T0006 0773071001 0560V20115 070C533008 070C533008 DF5EL3R0A0 076R0GF010 0163300005 098Q150403 100CT8R005 100CT3R505
CORD,AC BUSH FLAT CABLE FLAT CABLE CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
RC...................
CARBON RESISTOR
CC................... CE................... CP................... CPP.................. CPL.................. CMP................... CMPL................ CMPP................
CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR
RESISTOR
CAPACITORS
J2-4
9619901 AWM2468 AWG26 5C GRAY 260MM AWM2468 AWG26 7C GRAY 360MM SM1098-009-1A 173979-7 B06B-DVS A3963WV2-3PD A1561WV2-2P 003P-2100 003P-2100 A2361WV2-2P 005P-2100 CU146901 A2502WV2-4P B2013H02-5P B2013H02-5P B2013H02-7P B2013H02-7P XRY20X30BD XRY16X28BD 51MS063L FQI-14B003F EYF-52BC EYF-52BC RPM7138-H5 ALKS321 810-47-171 810-47-171 ZPB45BL3R0A R25-1911 115-V-K015AR B A36AKJ13X05 HC-49/U-S HC-49/C
TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN
