15.6 Finisher/saddle Finisher Error Codes

Transcript

Chapter 15　 15.6 Finisher/Saddle Finisher Error Codes 15.6.1 Error Code in Detail (finisher, puncher) 0008-1518 iR2270 / iR2870 / iR3570 / iR4570 T-15-15 Code Detail Name Detection Remedy code E500 0001 E503 0002 0003 E505 fault in communicatio n with the finisher (Finisher-Q3/ Q4) fault in communicatio n between finisher and saddle unit Replace the finisher controller PCB. Replace the saddle controller PCB. Check the cable. fault in communicatio n between finisher and punch unit Replace the finisher controller PCB. Replace the punch drive PCB. Check the cable. fault in the data stored in backup memory Turn off the main power. Check the wiring of the DC controller PCB and the finisher controller, and check the fuse of the 24-V power supply. Thereafter, turn the main power back on. fault in the EEPROM data of the punch unit Replace the punch driver PCB. Replace the finisher controller PCB. 0001 0002 15-50 Replace the finisher controller PCB. Replace the DC controller PCB. fault in communicatio n with the finisher (common among all finishers) fault in the backup memory of the finisher (common among all finishers) Code Detail Name Detection Remedy When the stack retaining spacer is returned to home position, the belt escape home position sensor does not go on within 1.5 sec. Replace the finisher controller PCB. Replace the stack delivery motor. Check the stack delivery drive mechanism. code E514 0001 0002 E514 fault in stack delivery motor (Finisher-S1) 0001 0002 fault in trailing edge assist motor (Finisher-Q3/ Q4) When the stack retaining spacer is shifted from home position, the belt escape home position sensor does not go off within 1.5 sec. The home position sensor does not go off even when the trailing edge assist motor has rotated for a specific period of time. The home position sensor does not go on even after the trailing edge assist motor has rotated for a specific period of time. Replace the finisher control PCB. Replace the trailing edge assist motor. Code Detail Name Detection Remedy The home position sensor does not go off even when the gear change motor has rotated for a specific period of time. Replace the finisher controller PCB. Replace the gear change motor. Check the gear change mechanism. code E519 0001 0002 E530 Gear change motor error (Finisher-Q3/ Q4) 8001 8002 Rear alignment error (Finisher-S1) The home position sensor does not go on even when the gear change motor has rotated for a specific period of time. The home position sensor does not go on within 2000 msec after the start of operation when the rear aligning plate is shifted to home position. The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is shifted from home position. Replace the finisher controlled PCB. Replace the rear alignment motor. Check the rear aligning plate drive mechanism. Check the rear alignment home position sensor. Code Detail Name Detection Remedy The home position sensor does not go off even when the front alignment motor has been rotated for a specific period of time. Replace the finisher controller PCB. Replace the front alignment motor. Check the front aligning plate drive mechanism. Check the front alignment home position sensor. code E530 0001 0002 E531 Front alignment error (Finisher-Q3/ Q4) 8001 Stapler error (Finisher-S1) 8002 The home position sensor does not go on even when the front alignment motor has been rotated for a specific period of time. At time of staple jam recovery, the home position sensor does not go on with 500 msec after the start of reverse rotation of the stapler motor. The home position sensor does not go off within 500 msec after the stapler motor has been started. Replace the finisher controller PCB. Replace the stapler. Check the harness. Code Detail Name Detection Remedy The home position sensor does not go off even when the stapler motor has rotated for a specific period of time. Replace the finisher controller PCB. Replace the stapler. Check the harness. code E531 0001 0002 E532 Stapler error (Finisher-Q3/ Q4) 8001 8002 Stapler shift error (Finisher-S1) The home position sensor does not go on even when the stapler motor has rotated for a specific period of time. The stapler slide home position sensor does not go on within 11 sec when the stapler is shifted to home position. The stapler slide home position sensor does not go off within 1.0 sec when the stapler is shifted from home position. Replace the finisher controller PCB. Replace the stapler shift motor. Check the stapler shift home position sensor. Check the harness. Code Detail Name Detection Remedy The home position sensor does not go off even after the stapler shift motor has rotated for a specific period of time. Replace the finisher controller PCB. Replace the stapler shift motor. Check the stapler shift home position sensor. Check the harness. code E532 0001 0002 E535 Stapler shift error (Finisher-Q3/ Q4) 0001 0002 Swing cam error (Finisher-S1) The home position sensor does not go on even when the stapler shift motor has rotated for a specific period of time. The home position sensor does not go off within 1000 msec after the start of operation when the swing arm is shifted from home position. The home position sensor does not go off within 1.0 sec when the stack delivery roller swing arm is moved from home position. Replace the finisher controller PCB. Replace the swing cam motor. Check the swing cam home position sensor. Check the harness. Code Detail Name Detection Remedy The home position sensor does not go off even when the swing motor has rotated for a specific period of time. Replace the finisher controller PCB. Replace the swing cam motor. Check the swing cam home position sensor. Check the harness. code E535 0001 0002 E537 Swing cam error (Finisher-Q3/ Q4) 8001 8002 Front alignment error (Finisher-S1) The home position sensor does not go on even when the swing motor has rotated for a specific period of time. The home position sensor does not go on within 2.0 sec when the front aligning plate is moved to home position. The home position sensor dos not go off within 1.0 sec when the front aligning plate is shifted from home position. Replace the finisher controller PCB. Replace the front alignment motor. Check the front aligning plate drive mechanism. Check the front alignment home position sensor. Code Detail Name Detection Remedy The home position sensor does not go on within 2000 msec after the start of operation when the read aligning plate is moved to home position. Replace the finisher controller PCB. Replace the rear alignment motor. Check the rear aligning plate drive mechanism. Check the rear alignment home position sensor. code E537 0001 0002 E540 Rear alignment error (Finisher-Q3/ Q4) 8002 8003 Stack tray motor error (Finisher-S1) The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is moved form home position. The operation to detect the paper surface of the stack tray does not end within 1.0 sec. Replace the finisher controller PCB. Replace the tray ascent/ descent motor. Check the stack tray drive mechanism. Check the paper surface sensor. An abnormal combination of sensor states has been detected. Replace the finisher controller PCB. Check the stack tray upper limit sensor. Check the stack tray lower limit sensor. Check the stack tray upper paper surface sensor. Check the stack tray lower paper surface sensor. Code Detail Name Detection Remedy code E540 0002 Upper tray ascent/descent motor clock error 0003 Upper tray ascent/descent motor error (Finisher -Q3/ Q4) Area error Replace the No. 1 tray area sensor PCB. Replace the finisher controller PCB. Safety switch activation Check the No. 1 tray closed detecting switch. Replace the finisher controller PCB. 0004 E542 0002 0003 Lower tray ascent/descent motor error (Finisher-Q3/ Q4) Replace the No. 1 tray shift motor. Replace the finisher controller PCB. Check the tray ascent/descent mechanism. Lower tray ascent/descent motor clock error Area error Replace the No. 2 tray shift motor. Replace the finisher controller PCB. Check the tray ascent/descent mechanism. Replace the No. 2 tray shift area sensor PCB. Replace the finisher controller PCB. Code Detail Name Detection Remedy The paddle home position sensor does not go on within 1.5 sec when the paddle is shifted to home position. Check the paddle motor. Check the paddle home position sensor. Replace the finisher controller PCB. code E577 8001 8002 E584 Paddle error (Finisher-S1) 0001 0002 Shutter unit error (Finisher-Q3/ Q4) The paddle home position sensor does not go off within 1.0 sec when the paddle is moved to home position. The shutter open sensor does not go off (i.e., the shutter does not close). The shutter open sensor does not go on (i.e., the shutter does not open). Check the stack edging motor. Check the open/ close clutch. Check the shutter home position sensor. Replace the finisher controller PCB. Code Detail Name Detection Remedy The punching home position is not detected even when the puncher motor has been driven for 20 msec. Check the punch motor. Check the punch motor clock sensor. Check the punch driver PCB. Replace the finisher controller PCB. code E590 0001 0002 E591 0001 0002 E592 E592 Punch motor error 0001 0002 Punch dust sensor error Paper trailing edge sensor/ horizontal sensor error paper trailing edge sensor/ registration sensor error The punch home position sensor is not defected even after the motor has stopped at time of punch motor initial operation. Error in lightreceiving voltage while light is emitted Error in lightreceiving voltage while light is not emitted Error in lightreceiving voltage when light is emitted (trailing edge sensor) Error in lightreceiving voltage when light is not emitted (trailing edge sensor) Check the waste paper case full sensor. Check the punch driver PCB. Replace the finisher controller PCB. Check the paper trailing edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. Check the paper trailing edge sensor. Check the horizontal registration sensor. Check the punch drive PCB. Replace the finisher controller PCB. Code Detail Name Detection Remedy Power trailing Error in lightreceiving voltage when light is emitted (horizontal registration sensor 1) Check the paper trailing Error in lightreceiving voltage when light is not emitted (horizontal registration sensor 1) Check the paper trailing Error in lightreceiving voltage when light is emitted (horizontal registration sensor 2) Check the paper training Error in lightreceiving voltage when light is not emitted (horizontal registration sensor 2) Check the paper training Error in lightreceiving voltage when light is emitted (horizontal registration sensor 3) Check the paper trailing code E592 0003 edge sensor/ registration sensor E592 0004 Paper trailing edge sensor/ registration sensor error E592 0005 Paper trailing edge sensor/ registration sensor error E592 0006 Paper trailing edge sensor/ registration sensor error E592 0007 Paper trailing edge sensor/ registration sensor error edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller. edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. Code Detail Name Detection Remedy Paper trailing Error in lightreceiving voltage when light is not emitted (horizontal registration sensor 3) Check the paper trailing Error in lightreceiving voltage when light is not emitted (horizontal registration sensor 4) Check the paper trailing Error in lightreceiving voltage when light is not emitted (horizontal registration sensor 4) Check the paper trailing The lightreceiving voltage home position sensor does not go off when light is emitted. Check the horizontal registration motor. Check the horizontal registration home position sensor. Check the punch driver PCB. Replace the finisher controller PCB. Check the punch shift mechanism. code E592 0008 edge sensor/ registration sensor error E592 0009 Paper trailing edge sensor/ registration sensor error E592 000A Paper trailing edge sensor/ registration sensor error E593 0001 0002 Punch shift motor error The lightreceiving voltage home position sensor does not go on when light is not emitted. edge sensor. Check the horizontal registration sensor. Check the punch drive PCB. Replace the finisher controller PCB. edge sensor. Check the horizontal registration sensor. Check the punch driver PCB. Replace the finisher controller PCB. edge sensor. Check the horizontal registration sensor. Check the punch drive PCB. Replace the finisher controller PCB. Code Detail Name Detection Remedy The paper positioning plate home position sensor does to go on when the paper positioning motor has been driven for 1.33 sec. Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S) Check the paper positioning plate motor. Check the paper positioning plate home position sensor. Replace the finisher controller PCB. Check the paper positioning plate drive mechanism. code E5F0 0001 0002 Saddle paper positioning plate error The paper positioning plate home position sensor doest not go off when the paper positioning plate motor has been driven for 1 sec. Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S) Code Detail Name Detection Remedy The number of detection pulses of the paper folding motor clock sensor has dropped below a specific value. Paper folding motor (M2S)/ paper folding motor clock sensor (P14S) Check the paper folding motor. Check the paper folding motor clock sensor. Replace the finisher controller PCB. Check the paper folding plate drive mechanism. code E5F1 0001 0002 Saddle paper folding error The state of the paper folding home position sensor doest not change when the paper folding motor has been driven for 3 sec. Paper folding motor (M2S)/ paper folding motor clock sensor (P14S) Code Detail Name Detection Remedy The guide home position sensor does not go on when the guide motor has been driven for 0.455 sec. Guide motor (M3S)/guide home position sensor (PI13S) Check the guide motor. Check the guide home position sensor. Replace the finisher controller PCB. Check the guide drive mechanism. code E5F2 0001 0002 Saddle guide error The guide home position sensor does not go off when the guide motor has been driven for 1 sec. Guide motor (M3S)/guide home position sensor (PI13S) Code Detail Name Detection Remedy The aligning plate home position sensor does not go on when the alignment motor has been driven for 0.5 sec. (at time of initialization, 1.67 sec.) Alignment motor (M5S)/ aligning plate home position sensor (PI5S) Check the alignment motor. Check the alignment home position sensor. Check the aligning plate drive mechanism. Replace the finisher controller PCB. code E5F3 0001 0002 saddle alignment error The aligning plate home position sensor does not go off when the alignment motor has been driven for 1 sec. Alignment motor (M5S)/ aligning plate home position sensor (PI5S) Code Detail Name Detection Remedy The stitching home position sensor does not go on when the stitch motor (rear) has been rotated in reverse for 0.5 sec or more. Stitch motor (rear; M6S)/ stitching home position sensor (rear; MS5S) Replace the stitcher (rear). Check the harness. Replace the finisher controller PCB. code E5F4 0001 0002 Saddle rear stapling error The stitching home position sensor does not go off when the stitch motor (rear) has been rotated in normal direction for 0.5 sec or more. Stitch motor (rear; MS)/ stitching home position sensor (rear; MS5S) Code Detail Name Detection Remedy The stitching home position sensor does not go on when the stitch motor (front) has been rotated in reverse for 0.5 sec or more. Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S) Replace the stitcher (front). Check the harness. Replace the finisher controller PCB. code E5F5 0001 0002 Saddle front stapling error The stitching home position sensor does not go off when the switch motor (front) has been rotated in normal direction for 0.5 sec or more. Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S) Code Detail Name Detection Remedy Check the paper butting plate motor. Check the paper butting plate home position sensor. Replace the finisher controller PCB. code E5F6 0001 Saddle butting error The paper butting plate home position sensor does not go on when the paper butting plate motor has been driven for 0.3 sec. Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S) E5F6 0002 Saddle butting The paper butting plate home position sensor does not go off when the paper butting plate motor has been driven for 80 msec or more. Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S) error Code Detail Name Detection Remedy Saddle butting The number of detection pulses of the paper butting plate motor has dropped below a specific value. paper butting plate motor (M8S)/paper butting plate motor clock sensor (PI1S) Check the paper butting plate motor. Check the paper butting plate motor clock sensor. Replace the finisher controller PCB. code E5F6 0003 error Code Detail Name Detection Remedy Saddle butting The paper butting plate leading edge sensor does not go off when the paper butting plate motor has been driven for 80 msec. Paper butting plate motor (M8S)/paper butting plate leading edge sensor (PI15S) Check the paper butting plate motor. Check the paper butting plate leading edge sensor. Replace the finisher controller PCB. code E5F6 0004 error E5F6 0005 Saddle butting error The paper butting plate leading edge sensor does not go on when the paper butting plate motor has been driven for 0.3 sec. Paper butting plate more (M8S)/paper butting plate leading edge sensor (PI15S) Code Detail Name Detection Remedy 0001 The connector of the paper butting plate home position sensor has been identified as being disconnected. Connector of guide home position sensor (PI13S) Connect the connector of the guide home position sensor. Check the harness. Replace the finisher controller PCB. 0002 The connector of the paper butting plate home position sensor has been identified as being disconnected. Connector of paper butting plate home position sensor (PI14S) Connect the connector of the paper butting plate home position sensor. Check the harness. Replace the finisher controller PCB. The connector of the paper butting plate leading edge sensor has been identified as being disconnected. Connector of paper butting plate leading edge sensor (PI15S) Connect the connector of the paper butting plate leading edge sensor. Check the harness. Replace the finisher controller PCB. code E5F8 Saddle connector error 0003 Code Detail Name Detection Remedy Saddle switch error The inlet cover switch has been identified as being open for 1 sec or more after the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed: - inlet cover sensor (PI9S) - nt cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front over switch (MS2S) or the delivery cover switch (MS3S) is open. Inlet cover switch (MS1S)/front cover switch (MS2S)/ delivery cover switch (MS3S) Check the inlet cover switch. Check the inlet cover sensor. Check the front cover open/ closed sensor. Check the delivery cover sensor. Replace the finisher controller PCB. code E5F 0001 Code Detail Name Detection Remedy Saddle switch The front cover switch has been identified as being open from the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed. - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - front cover switch (MS2S)/ delivery cover switch (MS3S) Check the front cover switch. Check the inlet cover sensor. Check the front cover open/ closed sensor. Check the delivery cover sensor. Replace the finisher controller PCB. code E5F 0002 error Code Detail Name Detection Remedy Saddle switch The delivery cover switch has been identified as being open after the start of printing or the start of initial rotation of the host machine with the following sensors identifying their respective covers as being closed: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S) Check the delivery cover switch. Check the inlet cover sensor. Check the inlet cover sensor. Check the front cover open/closed sensor. Check the delivery cover sensor. Replace the finisher controller PCB. code E5F 0003 error