Transcript
16-25-36 INPUTS H264 STAND-ALONE NETWORK VIDEO RECORDER ART. IPNVR006A IPNVR025A IPNVR036A
Please read this manual thoroughly before use and keep it for future reference
1
Technical parameters Model
IPNVR006A-IPNVR025A-IPNVR036A
Operation
Embedded Linux operation system
Operation system
Graphical user interface (GUI), mouse, front button, remote control
Imagine compression
H.264
Recording mode
Manual, Scheduled, Event
Video Search
Time, Event, Channel, Log
Backup
Network, USB
Video input
RJ45
Video output
VGA, HDMI
Motion Detection
each channel can set the detection area and the multi-level sensitivity
Image display
1/4/9/16
Video Save
HDD, network
HDD interface
SATA
USB Interface
2 x USB2.0
Power
100-240 VAC / 50-60 Hz
2
HDD Installation Make sure to install the HDD when You first use it.
.
Front Panel Description IPNVR006A front panel
1. HDD led
9. PLAY: Playback key
2. State led, reserved
10. ESC: Exit key
3. 1 ~ 8: CH1 ~ CH8 Single-Screen keys
11. MENU: Menu key
4. ▲▼◄►: Direction key
12.
5. POWER led
13. N.C.
: Confirm key
6. IR receiver 7. QUAD key 8. REC: Manual recording key
3
IPNVR025A-IPNVR036A front panel
1. POWER led
9. ESC: Exit key
2. HDD led
10. MENU: Menu key
3. REC: Manual recording key
11. ▲▼◄►: Direction key,
4. FN key
12. N.C.
: Confirm key
5. PLAY: Playback key 6. ON/OFF key 7. Multi-Screen key 8. Single-Screen keys
Rear Panel Description
NET: 10/100/1000 Mbit/sec. standard Ethernet port
DC12V: 12 VDC power supply connector
VGA: VGA video output connector
HDMI video output
USB: 2 x USB connectors
Audio IN/Audio out: audio input/output connectors
Operating System Description Turn ON / OFF Confirm that AC voltage matches with NVR .Ensure that the NVR power outlet connect with a good middle ground grounding. After switching power, the device started, 【POWER】 light is on. Turn into system, if the panel status light flashing ,it's normal conditions.
Preview After device start, preview interface can be seen immediately. In the preview interface you can see 4
the system date, time, channel name. Press corresponding number key of panel or click the left mouse button, user can preview the single channel; Press "QUAD" key in the panel or click the left mouse button, you can return to a multi-interface monitoring state.
Menu operation instructions Menu 【MENU】,enter the device's main menu interface. 【PLAY】 shortcut keys for playback interface. 【REC】shortcut keys for manual recording.【PTZ】shortcut keys for PTZ control. Note: default username is admin, default password is empty.
Menu composition Menu component units as following: （1）Check box: two kinds of status available, "√" means enabled, "□" means disabled; direction key: 【↑】【↓】【←】【--->】; enter key【
】. Also, click the left mouse button to choose.
For example: "channel" and "video mode" check box in the video research. （2）Selection box: select the target content according to the drop-down box options. Use 【↑】, 【↓】 key or click the left mouse button to select. For example: "channel" and "code stream" in the encode setup menu （3）List Box: displays the research information in the list, you can try one option for operation For example: press【
】 button in the video backup file. or the left mouse button.
（4）Edit box: enter the name into edit box For example: in the setup menu, you could input numbers, English letters, punctuation and so on in the "channel" edit box. a) use panel key 【↑】【↓】【←】, 【→】or move the mouse to edit box , press "
" key or click
the left mouse button, then enter keyboard appears, select the desired input target characters through the arrow keys or click the left mouse button. b) after input the information, click 【OK】【CANCEL】 button or button【ESC】can safe or exit （5） button: used to implement a specific function or enter the next setup menu, click【OK / key and the left mouse button.
ESC MENU Press 【MENU】, 【ESC】 or the right mouse button to exit the menu mode Click the right mouse button and return to the previous menu level.
Main Menu Introduction Press MENU key or right mouse, it will pop-up the main menu. Main menu consists of the following components:
5
Split screen: select corresponding preview mode in the menu column. Shortcut menu: in menu column, there are: Video Manage, System setup, Video playback, Video backup, Color adjust, PTZ control, Manual record, Volume, Setup Wizard, System mode, Fast network, Exit system. User could enter the corresponding menu preview mode.
System mode In the shortcut menu, click "System Mode", the following screen appears: IPNVR006A
You can choose between 4 different modes: A - 16 channels 1080p mode (720p, 960p and 1080p cameras). B – 16 channels hybrid mode (10 cameras 720p, 960p, 1080p and 6 cameras 3MP, 4MP, 5MP). C – 6 channels 5MP mode (720p, 960p, 1080p, 3MP, 4MP, 5MP cameras) D – 16 channels 3MP mode (720p, 960p, 1080p and 3MP cameras)
6
IPNVR025A
You can choose between 5 different modes: A - 25 channels 1080p mode (720p, 960p and 1080p cameras). B - hybrid mode 25 channels-1 (21 cameras 720p, 960p, 1080p and 4 cameras 3MP, 4MP, 5MP). C - hybrid mode 25 channels-2 (17 cameras 720p, 960p, 1080p and 8 cameras 3MP) D – 16 channels 5MP mode (720p, 960p, 1080p, 3MP, 4MP and 5MP cameras) E – 16 channels 3MP mode (720p, 960p, 1080p and 3MP cameras) IPNVR036A
You can choose between 6 different modes: A - hybrid mode 36 channels (35 cameras 720p, 960p, 1080p and 1 camera 3MP, 4MP, 5MP). B - hybrid mode 25 channels-1 (21 cameras 720p, 960p, 1080p and 4 cameras 3MP, 4MP, 5MP). C - hybrid mode 25 channels-2 (17 cameras 720p, 960p, 1080p and 8 cameras 3MP). D – 16 channels 5MP mode (720p, 960p, 1080p, 3MP, 4MP and 5MP cameras) E – 16 channels 3MP mode (720p, 960p, 1080p and 3MP cameras) F – 36 channels 1080p mode (720p, 960p and 1080p cameras). The cameras 3MP/4MP/5MP must be registered mandatory on the first channels!
7
Video Playback
Channel：to choose the target channel by clicking the check box
means non-selected.
Record mode：to choose the recode mode by clicking the check box Search time：input the starting and finishing time into edit box. Search：after setup the above search condition, click "search" to begin the corresponding video file searching and show the files. Red means time recording, green means MD recording, yellow means sensor recording. Playback: chose playback and turn into playback interface. In the search list box, choose the time bucket according up, down, left, right key or move the mouse. Click 【
】or left mouse
to enter "video playback" interface Cancel：back to previous menu Playback toolbar Select the playback file or time playback file, it will turn into video playback interface. Playback toolbar: it will show below the playback interface. Each channel can magnify or narrow by clicking the left mouse. Stop play：click Pause/play: click Fast forward：click
to stop the video and turn back to playback interface. can pause the playback video, click
can continue the playback video.
can fast-forward the video, also times fast forward the video by click the
button again. Exit playback：click “ESC” or
can exit the playback video; or exit until all file have been played.
Manual Record
In the shortcut menu, click Manual record or click 【REC】 to enter the setup the manual record interface. 8
Manual record menu include several parts: Channel: ☑”means enable; “□”means disable. All on: enable all the channel. All off: disable all the channel. OK: confirm an exit Cancel: click cancel can exit the manual record interface and back to main menu.
PTZ control
Choose the "PTZ control" from shortcut menu . PTZ control menu including: direction control; auto pan scan; zoom; focus; Iris; speed.
Video back up
Choose the channel, and record mode; setup the search time, then begin search the file. After choosing the needed file from list box, click Backup and Ok, wait for process bar until 100% and show backup success. Notes：USB driver pen must be FAT32 format when backup the file
9
General setup
Choose the "General setup" and turn into it's setup interface.
Time Setup：the real time when preview, click ”Refresh” after setting, make sure saving when it shows ”the recording will stop once you modify the time” and save the setting. Auto Logout: the present user will be logged off if there is no operation within 10 minutes, and it needs login again. Key Buzzer：enabled, there is sound with the controller or pressing key on front panel. Disabled, without sound. Language：there is multiple choices according to users, English and so on. Remote ID：user can use this ID to control the NVR by remote controller. The remote controller should be correspond with the ID so that it can work. After setting finished, click "Ok", the information will be saved. Click "Cancel" to exit without saving.
Video manage
Before connecting and set up IPC, please confirm that IPC is already connected to LAN. Right click on the preview interface, pop-up shortcut interface, click “Video manage". Add one: add the selected camera Auto Add: add all cameras detected Delete: delete the selected connected IPC 10
Delete All: delete all the connected IPC Manual Edit: modify the IPC parameters of the selected IPC After finish setup, click “ Ok” button, it will be saved; click: “Cancel” button, it will be not save
Record Setup
Select “Record setup”. Channel：chose the channels as needed by clicking the inverted triangle Weekday: chose the day as needed, "ALL" means all days in a week. Schedule： every time slot can set different recording modes in all 4 time slot. "Time" recording with red color, "Motion" recording with green color, "Sensor" recording with yellow color; “☑" means enabled, “□” means disabled. The bottom parts has times status display, whole schedule from time 0~24 hours Copy to： select the target channel on the right of "copy to "button, click "copy to" and ''Ok" to set the current channel setup informations to other target video channel. By clicking the button "Cancel", the setup informations are non-saved.
Network setup
11
Select “network setup”. DHCP: choose to enable to obtain IP address automatically. "☑" means enabled ，"□" means disabled Cloud (P2P)：after connecting internet , click“☑ Cloud (P2P)” to gain a ID , which can be used in IP remote monitoring in ESeenet network server IP address：the IP address must be unique and cannot be in conflict with the host or workstation on the same network segment Subnet mask：subnet for the network segment. Gateway： need to set the gateway address to achieve communication between the different network segments. MAC address：showing the device's MAC address Preferred DNS：DNS IP address Web port：port number IE browser visit, default port is "80"
PPPOE Start using：“☑ PPPOE” means to start up PPPOE dial-up. “□” means not to start up Username：input the user name of ISP into edit box Password：input the password of ISP into edit box After the page setup is completed, click '"Ok" to save the changes; click "Cancel ", non-save.
DDNS Automatic analytical function of dynamic domain name, supported Comelit DNS, etc. To use Comelit DNS see the last page of this manual. In the "network setup" menu, click " DDNS " Start using：“☑”means DDNS dynamic domain services start using: “□”means not to start up. Select the right network server and input user name, password and domain
Screen Setup
Select “screen setup” OSD Alpha：OSD menu transparency can be adjusted as needed. 12
VGA Resolution: choose the desired resolution Auto Switch: user can setup the time of auto switching for preview image, it switch in single screen or 4 channels screen. Enable：“☑”start using, “□” non-start using After the page setup is completed, click '"Ok" to save the changes ; click "Cancel ", non-save.
Video detection
Channel: the option to set the alarm channel selection box Detection：select detection type
motion, video loss
Sensitivity：chose the trigger video detection sensitivity Alarm duration: after chose the trigger video detection, choose the time alarm. Area edit : setup motion detection area; move by dragging the left of mouse. Alarm：“☑”means start ，“□”means non start 。 Buzzer ：“☑”means start ，“□”means non start。 E-Mail notice: “☑” means sent E-Mail enabled, “□” means sent E-Mail disabled. Copy to： click "copy to", select the target channels and ''Ok" to set the current channel setup informations to other target video channel. By clicking the button "Cancel", the setup informations are non-saved.
13
PTZ Setup
Select ”PTZ setup” Select ”PTZ setup” Channel: choose the right channel, click the select box to choose Protocol: the selected protocol must be the same with the one of PTZ Copy to： click "copy to", select the target channels and ''Ok" to set the current channel setup informations to other target video channel. By clicking the button "Cancel", the setup informations are non-saved. After the setting, click the button of sure to exit with saving the setting, or click the button Cancel to exit without saving.
Sensor setup
Select "Sensor setup". Channel: choose the right channel, click the select box to choose Work mode: setting to start alarm or not Alarm duration: set up alarm duration time Record channel: when alarm is triggered, channel needed to be recorded Alarm: “☑” enable alarm, “□” close alarm Buzzer: “☑”start buzzer, “□” close buzzer 14
Copy to：click "copy to", select the target channels and ''Ok" to set the current channel setup informations to other target video channel. By clicking the button "Cancel", the setup informations are non-saved. After the setting, click "OK" to exit with saving or click "Cancel" to exit without saving.
User management
Select "User". Add user: input a new user name in the edit box and set up the operational authority. Click the "Set Password" to set the new password or it can be the default password. Delete user: delete the selected user (except Admin, other user has no the right to set up or delete other users) Edit user: modify the selected user (Admin, other users has no right to set up other user permissions) Set password: set password of logging in user After the setting, click "OK" to save and exit, or click "cancel" to exit without saving
HDD setup
Select "HDD setup". Overwrite: “☑” earliest recording files will be covered when the disk is full, “□"shows not cover. Format: “☑” stands selected, “□” stands not selected, when click "Format" a confirm interface will pop up, then click confirm to format, click cancel to return the main interface. 15
System maintenance
Select
"System maintenance".
Auto reboot: setting automatic reboot time, it can set" Saturday to Sunday", "Never" means do not reboot automatically.
System upgrade: copy firmware to the root directory of USB drive, insert USB, select the USB storage device, then click "start" to upgrade. When upgrade is completed, click "Ok" then system auto reboot. Note: during upgrade, do not cut off power to protect from device damage
Factory setting
Select "Factory setting". Select the items which need factory setting, click "Ok" to save and exit or click "Cancel" to exit without saving. Notes: after factory setting, all the settings will be the initial one, please use carefully.
16
HDD info
The listbox shows the HDD status information
System version
Device name ,device model, H/W version, S/W version could be checked here.
System log Choose the log type which need to check from list box, and input the time period in the edit box, then click "Search", the related log information will showed below, you can turn the page by click "previous" and "next" or input target page to turn
System logout In the main menu, click "System logout", popup setting interface
17
Logout: apply for logging users. After logout, if you want to use the device again, need to login again Reboot: it will reboot after "OK". Shutdown: shutdown the NVR
Esee User Manual 1. Connect DVR with network, make sure network working fine 2. For remote view in computer, go to www.dvrskype.com or www.e-seenet.com Do the following setup before you log in Esee on computer Note: Internet Explorer setting. If use it for the first time and the software can't load, then need to make the following setting: Internet options
Safety-Internet
Custom options
pick Active X and plugin all for opening, click ok. 1. Go to www.dvrskype.com or www.e-seenet.com,input Esee ID, user name and password, this user name and password is same with DVR user name and password Note: the default user name is admin, no password
Video monitoring homepage: Monitoring homepage including: preview window, PTZ control, preview, stream selection, channel opening, setting, playback, user logout, as below:
18
Open preview：click the target channel with mouse left. Double click the channel can open or close the correspond preview channel, such as: Preview mode: click
open;
close.
to choose the mode or double click preview window to switchover
into multi-channel mode NOTE: to view images of NVRs art. IPNVR006A, IPNVR025A and IPNVR036A from smartphones (iOS or Android OS) please use the app "Comelit View S" which is freely downloadable from the relative stores (Apple Store and Google Play). The same app for smartphones has to be used for tablet devices.
COMELIT DNS SERVICE For this series of NVR is now available the Comelit DNS service. To use it proceed as follows: 1 – check the firmware version of the device. If necessary, update the firmware 2 – verify that, on the device, nearby the label showing the model, is present the label with the univocal code for the DNS service registration. In case it was not present, contact Comelit Technical support 3 – connect to the site http://www.comelitdns.com, sign up by following the instructions and then create a host using the activation code above 4 – enter the data (hostname, user and password) in the appropriate NVR menu 5 – to connect to the device registered, enter http://hostname.comelitdns.com:port (if different from 80)
19
20
