Transcript
16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668 OUT 1 V– 2
The AD866x family is single supply, rail-to-rail output amplifiers with low noise performance featuring an extended operating range with supply voltages up to 16 V. They also feature low input bias currents, wide signal bandwidth, and low input voltage and current noise. For lower offset voltage, choose the AD8661/AD8662/AD8664 family. The combination of low offsets, very low input bias currents, and wide supply range make these amplifiers useful in a wide variety of cost sensitive applications normally associated with much higher priced JFET amplifiers. Systems using high impedance sensors, such as photo diodes, benefit from the combination of low input bias current, low noise, and low offset and bandwidth. The wide operating voltage range matches high performance ADCs and DACs. Audio applications and medical monitoring equipment can take advantage of the high input impedance, low voltage and current noise, wide bandwidth, and the lack of popcorn noise found in many other low input bias current amplifiers. The AD866x family is specified over the extended industrial temperature range (−40°C to +125°C). See the Ordering Guide for automotive models.
V+
4
–IN
NC
1
–IN
2
+IN
3
AD8665
TOP VIEW 4 (Not to Scale)
VEE
8
NC
7
VCC
6
OUT
5
NC
NC = NO CONNECT
06195-040
Figure 1. AD8665, 5-Lead SOT-23 (RJ-5)
OUT A
1
–IN A
2
+IN A
3
AD8666
TOP VIEW 4 (Not to Scale)
V–
8
V+
7
OUT B
6
–IN B
5
+IN B
06018-001
Figure 2. AD8665, 8-Lead SOIC_N (R-8)
Figure 3. AD8666, 8-Lead SOIC_N (R-8) OUT A
1
–IN A
2
AD8666
+IN A
3
V–
4
TOP VIEW (Not to Scale)
8
V+
7
OUT B
6
–IN B
5
+IN B
06195-002
GENERAL DESCRIPTION
5
TOP VIEW (Not to Scale)
+IN 3
APPLICATIONS Sensor amplification Reference buffers Medical equipment Physiological measurements Signal filters and conditioning Consumer audio Photodiode amplification ADC driver Level shifting circuits
AD8665
06195-039
PIN CONFIGURATIONS
Figure 4. AD8666, 8-Lead MSOP (RM-8) OUT A
1
14 OUT D
IN A
2
13 –IN D
+IN A
3
AD8668
V+
4
TOP VIEW (Not to Scale)
+IN B
5
10 +IN C
–IN B
6
9
–IN C
OUT B
7
8
OUT C
12 +IN D 11 V–
06195-003
Offset voltage: 2.5 mV max Low input bias current: 1 pA max Single-supply operation: 5 V to 16 V Dual-supply operation: ±2.5 V to ±8 V Low noise: 8 nV/√Hz @ 10 kHz Wide bandwidth: 4 MHz Rail-to-rail output Unity-gain stable Lead-free packaging AD8666/AD8668 qualified for automotive applications
Figure 5. AD8668, 14-Lead TSSOP (RU-14) OUT A
1
14
–IN A
2
13
–IN D
+IN A
3
12
+IN D
AD8648 AD8668
OUT D
11 V– TOP VIEW (Not to Scale) 10 +IN C
V+
4
+IN B
5
–IN B
6
9
–IN C
OUT B
7
8
OUT C
06195-004
FEATURES
Figure 6. AD8668, 14-Lead SOIC_N (R-14)
Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006–2011 Analog Devices, Inc. All rights reserved.
AD8665/AD8666/AD8668 TABLE OF CONTENTS Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................5
Applications ....................................................................................... 1
Thermal Resistance .......................................................................5
General Description ......................................................................... 1
ESD Caution...................................................................................5
Pin Configurations ........................................................................... 1
Typical Performance Characteristics ..............................................6
Revision History ............................................................................... 2
Outline Dimensions ....................................................................... 12
Specifications..................................................................................... 3
Ordering Guide .......................................................................... 14
REVISION HISTORY 7/11—Rev. A to Rev. B Change to Features and General Description Sections ............... 1 Updated Outline Dimensions ....................................................... 12 Changes to Ordering Guide .......................................................... 13 Added Automotive Products Section........................................... 13 10/06—Rev. 0 to Rev. A Added AD8665 ................................................................... Universal Added New Figure 1 and Figure 2, Renumbered Sequentially................................................................ 1 Changes to Table 4 ............................................................................ 5 Changes to Figure 8, Figure 9, and Figure 11 ............................... 6 Change to Figure 40 ....................................................................... 11 Updated Outline Dimensions ....................................................... 12 Changes to Ordering Guide .......................................................... 13 4/06—Rev 0: Initial Version
Rev. B | Page 2 of 16
AD8665/AD8666/AD8668 SPECIFICATIONS VDD = 5.0 V, VCM = VDD/2, TA = 25oC, unless otherwise noted. Table 1. Parameter INPUT CHARACTERISTICS Offset Voltage
Symbol
Conditions
VOS
Offset Voltage Drift Input Bias Current
ΔVOS/ΔT IB
VCM = 2.5 V VCM = −0.1 V to +3.0 V −40°C < TA < +125°C −40°C < TA < +125°C
Input Offset Current
IOS
Min
Typ
Max
Unit
0.7
2.5 3.0 5.0 10 1 550 0.5 70 +3.0
mV mV mV μV/°C pA pA pA pA V dB dB V/mV
3.0 0.2
−40°C < TA < +125°C 0.1 −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio Large-Signal Voltage Gain OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Output Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current per Amplifier
VCM CMRR AVO VOH VOL ISC ZOUT PSRR
VCM = −0.1 V to +3.0 V −40°C < TA < +125°C RL = 2 kΩ, VO = 0.5 V to 4.5 V IOUT = 1 mA −40°C < TA < +125°C IOUT = 1 mA −40°C < TA < +125°C
−0.1 84 79 68 4.88 4.86
ISY
145 4.93 50
98 94
115 1.1
−40°C < TA < +125°C DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Channel Separation
85 105
±19 50
At 1 MHz, AV = 1 VDD = 5.0 V to 16 V −40°C < TA < +125°C
100
1.4 2.0
V V mV mV mA Ω dB dB mA mA
SR GBP ΦM
RL = 2 kΩ
3.5 4 70
V/μs MHz Degrees
en p-p en
0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 10 kHz
2.4 10 8 −115
μV p-p nV/√Hz nV/√Hz dB
CS
Rev. B | Page 3 of 16
AD8665/AD8666/AD8668 VDD = 16 V, VCM = VDD/2, TA = 25oC, unless otherwise noted. Table 2. Parameter INPUT CHARACTERISTICS Offset Voltage
Symbol
Conditions
VOS
Offset Voltage Drift Input Bias Current
ΔVOS/ΔT IB
VCM = 8 V VCM = −0.1 V to +14.0 V −40°C < TA < +125°C −40°C < TA < +125°C
Input Offset Current
IOS
Min
Typ
Max
Unit
0.6
2.5 3.0 5.0 10 1 550 0.5 70 +14.0
mV mV mV μV/°C pA pA pA pA V dB dB V/mV
3.0 0.2
−40°C < TA < +125°C 0.1 −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio Large-Signal Voltage Gain OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Output Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current per Amplifier
VCM CMRR AVO VOH VOL ISC ZOUT PSRR
VCM = −0.1 V to +14.0 V −40°C < TA < +125°C RL = 2 kΩ, VO = 0.5 V to 15.5 V IOUT = 1 mA −40°C < TA < +125°C IOUT = 1 mA −40°C < TA < +125°C
−0.1 90 80 130 15.94 15.90
ISY
255 15.96 22
98 94
115 1.15
−40°C < TA < +125°C DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Channel Separation
40 50
±140 50
At 1 MHz, AV = 1 VDD = 5.0 V to 16 V −40°C < TA < +125°C
110
1.55 2.0
V V mV mV mA Ω dB dB mA mA
SR GBP ΦM
RL = 2 kΩ
3.5 4 73
V/μs MHz Degrees
en p-p en
0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 10 kHz
2.5 10 8 −115
μV p-p nV/√Hz nV/√Hz dB
CS
Rev. B | Page 4 of 16
AD8665/AD8666/AD8668 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE
Table 3. Parameter Supply Voltage Input Voltage Differential Input Voltage Output Short-Circuit to GND Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 60 sec) Junction Temperature
Rating 18 V GND to VDD ±18 V Indefinite −65°C to +150°C −40°C to +125°C 300°C 150°C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Table 4. Thermal Resistance Package Type 5-Lead SOT-23 (RJ-5) 8-Lead SOIC_N (R-8) 8-Lead MSOP (RM-8) 14-Lead SOIC (R-14) 14-Lead TSSOP (RU-14)
ESD CAUTION
Rev. B | Page 5 of 16
θJA 240 158 210 120 180
θJC 92 43 45 36 35
Unit °C/W °C/W °C/W °C/W °C/W
AD8665/AD8666/AD8668 TYPICAL PERFORMANCE CHARACTERISTICS 100
300
VS = 5V AND 16V
250
INPUT BIAS CURRENT (pA)
NUMBER OF AMPLIFIERS
VDD = 16V 90 VCM = 8V TA = 25°C 80 600 AMPLIFIERS 70 60 50 40 30 20
200
150
100
50
–2
–1
0
1
2
3
INPUT OFFSET VOLTAGE (mV)
0 –40
06195-005
0 –3
10000
VDD = 16V VCM = 8V –40°C < TA < +125°C 300 AMPLIFIERS
OUTPUT SATURATION VOLTAGE (mV)
NUMBER OF AMPLIFIERS
20
40
60
80
100
120
Figure 10. Input Bias Current vs. Temperature
20
16
0
TEMPERATURE (°C)
Figure 7. Input Offset Voltage Distribution
18
–20
06195-008
10
14 12 10 8 6 4
VDD = 16V TA = 25°C
1000 VDD TO VOH SOURCING 100 VOL SINKING 10
1
0.1 0.001
1
0
2
3
4
5
6
7
8
9
10
11
12
TCVOS (µV/°C)
06195-006
0
0.1
1
10
100
LOAD CURRENT (mA)
Figure 11. Output Saturation Voltage vs. Load Current
Figure 8. VOS Drift (TCVOS) Distribution
100
5
OUTPUT SATURATION VOLTAGE (mV)
VDD = 16V 4 TA = 25°C 3 2 1 0 –1 –2 –3
VDD = 16V IOUT = 1mA
80
60 VDD TO VOH SOURCING 40
VOL SINKING
20
–5 –1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
INPUT COMMON-MODE VOLTAGE (V)
0 –40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 12. Output Saturation Voltage vs. Temperature
Figure 9. Offset Voltage vs. Common-Mode Voltage
Rev. B | Page 6 of 16
120
06195-010
–4 06195-007
INPUT OFFSET VOLTAGE (mV)
0.01
06195-009
2
AD8665/AD8666/AD8668
PHASE
40
20
90
ФM = 73°
GAIN
135
180
0
80
60
PSRR (dB)
45
60
VDD = 16V TA = 25°C
OPEN-LOOP PHASE SHIFT (Degrees)
VDD = 16V RL = 2kΩ CL = 10pF
40
20
PSRR–
100k
1M
0 1k
06195-011
10k
225 10M
FREQUENCY (Hz)
10k
100k
1M
Figure 16. Power Supply Rejection Ratio vs. Frequency
Figure 13. Open-Loop Gain and Phase vs. Frequency
100
1000 VDD = 16V
VOLTAGE NOISE DENSITY (nV/√Hz)
VDD = 5V TO 16V TA = 25°C
10
AV = +100
AV = +10
AV = +1
1
0.01 100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
1 10
06195-012
0.1
10
100
1k
10k
FREQUENCY (Hz)
Figure 17. Voltage Noise Density vs. Frequency
Figure 14. Closed-Loop Output Impedance vs. Frequency
120
VDD = 5V TO 16V TA = 25°C
VDD = 16V TA = 25°C
VOLTAGE (1µV/DIV)
100
80
60
40
10k
100k
1M
FREQUENCY (Hz)
4M
Figure 15. Common-Mode Rejection Ratio vs. Frequency
TIME (1s/DIV)
Figure 18. 0.1 Hz to 10 Hz Voltage Noise
Rev. B | Page 7 of 16
06195-016
0 1k
06195-013
20
06195-015
100
ZOUT (Ω)
4M
FREQUENCY (Hz)
06195-014
PSRR+ –20 1k
CMRR (dB)
OPEN-LOOP GAIN (dB)
100
0
80
AD8665/AD8666/AD8668 VDD = 16V RL = 10kΩ CL = 10pF AV = +1
0V
VOUT (20mV/DIV)
VDD = ±8V AV = –100 VIN
–100mV 8V
VOUT
TIME (0.5µs/DIV)
06195-020
06195-017
0V
TIME (5µs/DIV)
Figure 19. Small-Signal Transient Response
Figure 22. Positive Overload Recovery Time
10 VDD = ±8V RL = 10kΩ CL = 10pF AV = +1
8 6
VDD = ±8V AV = –100
100mV VIN
VOUT (V)
4 2
0V
0
0V
–2 –4 –6
06195-018
–10 TIME (2µs/DIV)
TIME (5µs/DIV)
Figure 23. Negative Overload Recovery Time
Figure 20. Large-Signal Transient Response
80
70 VDD = 16V VIN = 100mV p-p
70
NUMBER OF AMPLIFIERS
60
40 +OS –OS
20
10
VDD = 5V VCM = 2.5V TA = 25°C 550 AMPLIFIERS
60 50 40 30 20
0 1
10
100
1000
LOAD CAPACITANCE (pF)
0 –3
–2
–1
0
1
2
INPUT OFFSET VOLTAGE (mV)
Figure 24. Input Offset Voltage Distribution
Figure 21. Small-Signal Overshoot vs. Load Capacitance
Rev. B | Page 8 of 16
3
06195-022
10
06195-019
OVERSHOOT (%)
50
30
06195-021
VOUT
–8V
–8
AD8665/AD8666/AD8668 VDD = 5V ILOAD = 1mA
OUTPUT SATURATION VOLTAGE (mV)
20
15
10
5
100 VDD TO VOH SOURCING 80
60 VOL SINKING 40
20
0 –40
1
0
2
3
4
5
6
7
8
9
10
TCVOS (µV/°C)
06195-023
0
0
20
40
60
80
120
100
TEMPERATURE (°C)
Figure 28. Output Saturation Voltage vs. Temperature
Figure 25. VOS Drift (TCVOS) Distribution
80
5
0 VDD = 5V RL = 2kΩ CL = 10pF
VDD = 5V TA = 25°C
4
60
3
OPEN-LOOP GAIN (dB)
INPUT OFFSET VOLTAGE (mV)
–20
06195-026
25 NUMBER OF AMPLIFIERS
120
VDD = 5V VCM = 2.5V –40°C ≤ TA ≤ +125°C 300 AMPLIFIERS
2 1 0 –1 –2
45
PHASE
40
20 GAIN
90
135
ФM = 70°
0
–3
180
OPEN-LOOP PHASE SHIFT (Degrees)
30
0
0.5
1.0
1.5
2.0
2.5
3.5
3.0
INPUT COMMON-MODE VOLTAGE (V)
–20 1k
10k
FREQUENCY (Hz)
1000 VDD = 5V TA = 25°C
VDD = 5V
100
VDD TO VOH SOURCING 10
ZOUT (Ω)
100
VOL SINKING
1
10 AV = +100 1
AV = +10
0.1
0.1 0.001
0.01
0.1
1
10
LOAD CURRENT (mA)
20
0.01 100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 30. Closed-Loop Output Impedance vs. Frequency
Figure 27. Output Saturation Voltage vs. Load Current
Rev. B | Page 9 of 16
10M
06195-028
AV = +1
06195-025
OUTPUT SATURATION VOLTAGE (mV)
1000
225 10M
1M
Figure 29. Open-Loop Gain and Phase vs. Frequency
Figure 26. Offset Voltage vs. Common-Mode Voltage
3000
100k
06195-027
–5 –0.5
06195-024
–4
AD8665/AD8666/AD8668 120
1.5
VDD = 5V TA = 25°C
VDD = ±2.5V RL = 10kΩ CL = 10pF AV = +1
1.0
100 0.5 0
VOUT (V)
CMRR (dB)
80
60
–0.5 –1.0
40 –1.5
20
10k
100k
4M
1M
FREQUENCY (Hz)
–2.5
06195-029
0 1k
06195-032
–2.0
TIME (1µs/DIV)
Figure 34. Large-Signal Transient Response
Figure 31. Common-Mode Rejection Ratio vs. Frequency
100
70 VDD = 5V TA = 25°C
VDD = 5V VIN = 100mV p-p
60
80
OVERSHOOT (%)
60
40
40 +OS 30 –OS 20
PSRR– 20
10 PSRR+ 100k
1M
4M
FREQUENCY (Hz)
0 1
10
06195-033
10k
06195-030
1000
100
LOAD CAPACITANCE (pF)
Figure 32. Power Supply Rejection Ratio vs. Frequency
Figure 35. Small-Signal Overshoot vs. Load Capacitance
VDD = ±2.5V AV = –100
VDD = 5V RL = 100kΩ CL = 10pF AV = +1
2.5V VOUT
0V 0V VIN
TIME (0.4µs/DIV)
06195-031
–100mV
TIME (4µs/DIV)
Figure 36. Positive Overload Recovery Time
Figure 33. Small-Signal Transient Response
Rev. B | Page 10 of 16
06195-034
0 1k
VOUT (20mV/DIV)
PSRR (dB)
50
AD8665/AD8666/AD8668 2.00
VDD = ±2.5V AV = –100
1.75
SUPPLY CURRENT (mA)
100mV VIN
0V 0V
1.50 1.25 1.00 0.75 0.50
VOUT 06195-035
TIME (4µs/DIV)
0 0
2
4
6
8
10
12
14
SUPPLY VOLTAGE (V)
Figure 37. Negative Overload Recovery Time
Figure 39. Supply Current vs. Supply Voltage
2.0
10
1.8
8
1.6
6
1.4
VDD = ±8V AV = +1
VIN VOUT
4
VDD = 5V 1.0 0.8
2 0 –2
0.6
–4
0.4
–6
0.2
–8
–20
0
20
40
60
80
100
TEMPERATURE (°C)
120
–10 TIME (10µs/DIV)
Figure 40. No Output Phase Reversal
Figure 38. Supply Current vs. Temperature
Rev. B | Page 11 of 16
06195-038
VOLTAGE (V)
VDD = 16V 1.2
06195-036
SUPPLY CURRENT (mA)
VOUT = VDD/2
0 –40
16
06195-037
0.25 –2.5V
AD8665/AD8666/AD8668 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890)
8
4.00 (0.1574) 3.80 (0.1497)
5
1
6.20 (0.2441) 5.80 (0.2284)
4
1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040)
1.75 (0.0688) 1.35 (0.0532)
0.51 (0.0201) 0.31 (0.0122)
COPLANARITY 0.10 SEATING PLANE
0.50 (0.0196) 0.25 (0.0099)
45°
8° 0° 0.25 (0.0098) 0.17 (0.0067)
1.27 (0.0500) 0.40 (0.0157)
012407-A
COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 41. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches)
3.20 3.00 2.80
8
3.20 3.00 2.80
1
5.15 4.90 4.65
5
4
PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75
15° MAX 1.10 MAX
0.40 0.25
6° 0°
0.23 0.09
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 42. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters
Rev. B | Page 12 of 16
0.80 0.55 0.40 10-07-2009-B
0.15 0.05 COPLANARITY 0.10
AD8665/AD8666/AD8668 5.10 5.00 4.90
14
8
4.50 4.40 4.30
6.40 BSC 1
7
PIN 1 0.65 BSC 1.20 MAX
0.15 0.05 COPLANARITY 0.10
0.20 0.09
0.30 0.19
0.75 0.60 0.45
8° 0°
SEATING PLANE
061908-A
1.05 1.00 0.80
COMPLIANT TO JEDEC STANDARDS MO-153-AB-1
Figure 43. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters
8.75 (0.3445) 8.55 (0.3366) 8
14 1
7
1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10
0.51 (0.0201) 0.31 (0.0122)
6.20 (0.2441) 5.80 (0.2283)
0.50 (0.0197) 0.25 (0.0098)
1.75 (0.0689) 1.35 (0.0531) SEATING PLANE
45°
8° 0° 0.25 (0.0098) 0.17 (0.0067)
1.27 (0.0500) 0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 44. 14-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches)
Rev. B | Page 13 of 16
060606-A
4.00 (0.1575) 3.80 (0.1496)
AD8665/AD8666/AD8668 3.00 2.90 2.80
1.70 1.60 1.50
5
4
1
2
3.00 2.80 2.60
3
0.95 BSC 1.90 BSC
1.45 MAX 0.95 MIN 0.15 MAX 0.05 MIN
0.50 MAX 0.35 MIN
0.20 MAX 0.08 MIN
SEATING PLANE
10° 5° 0°
0.60 BSC
0.55 0.45 0.35 11-01-2010-A
1.30 1.15 0.90
COMPLIANT TO JEDEC STANDARDS MO-178-AA
Figure 45. 5-Lead Small Outline Transistor Package [SOT-23] (RJ-5) Dimensions shown in millimeters
ORDERING GUIDE Model 1, 2 AD8665ARZ AD8665ARZ-REEL AD8665ARZ-REEL7 AD8665ARJZ-R2 AD8665ARJZ-REEL AD8665ARJZ-REEL7 AD8666ARZ AD8666ARZ-REEL AD8666ARZ-REEL7 AD8666ARMZ AD8666ARMZ-REEL AD8666WARZ-R7 AD8666WARZ-RL
Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C
Package Description 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead MSOP 8-Lead MSOP 8-Lead SOIC_N 8-Lead SOIC_N
Package Option R-8 R-8 R-8 RJ-5 RJ-5 RJ-5 R-8 R-8 R-8 RM-8 RM-8 R-8 R-8
AD8668ARZ AD8668ARZ-REEL AD8668ARZ-REEL7 AD8668ARUZ AD8668ARUZ-REEL AD8668WARUZ-R7 AD8668WARUZ-RL
−40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C
14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP
R-14 R-14 R-14 RU-14 RU-14 RU-14 RU-14
1 2
Branding
A1B A1B A1B
A16 A16
Z = RoHS Compliant Model W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS The AD8666W/AD8668W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. B | Page 14 of 16
AD8665/AD8666/AD8668 NOTES
Rev. B | Page 15 of 16
AD8665/AD8666/AD8668 NOTES
©2006–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06195-0-7/11(B)
Rev. B | Page 16 of 16
