Transcript
1701G GM Databus Interface IMPORTANT! Please read this installation guide thoroughly before installing the 1701G. Use only a high quality digital multi-meter for testing. This product connects to the vehicle’s low voltage signal wire and improper installation or testing can result in damage to the vehicle. Never use a test light or logic probe to test wires in this vehicle!
The 1701G interfaces with specific GM vehicles. It converts the signals from the keyless entry, alarm, or remote start into signals that can be understood by the vehicles factory Data Bus system. This allows for interfacing with various factory options such as factory Remote start, alarm and keyless entry. This unit can be used to interface using an aftermarket keyless entry, alarm or remote start.
Getting Started 1. Read manual thoroughly. 2. Make all wiring connections Prior to starting car or plugging in the 1701G module. 3. Plug in 1701G module and led will blink software version. (see version reporting on page 6) 4. Turn ignition ON, LED will blink quickly while learning the and vehicle turn solid once learned. (do not start vehicle until learning is complete). See LED diagnostics on page 4 if Led does not turn solid indicating a successful vehicle learn. 5. Make any desired feature programming changes.
Wiring Guide RED (+) 12V constant power input: Connect to the battery positive terminal or another constant 12 V supply. VIOLET/WHITE RPM (Tachometer) output: Connect this wire to “Tachometer input wire” of the remote start module. BLACK (-) chassis ground connection: Connect this wire to a clean, paint free metal sheet location using a factory bolt that DOES NOT have any vehicle component grounds attached to it. NOTE - Under dash bracing and steering columns are NOT proper ground points. Use either a kick panel or firewall and scrape off the paint at the contact point. LT. GRAY (-) hood status output: Connect this wire to the (-) hood pin input of the Security/Remote Start system. GREEN/BLACK (-) arm/lock input: Connect this wire to “lock #30 common output” or negative output of the door lock harness of the security system. The “lock #87 normally open input” of the security system must be grounded. © 2006 Directed Electronics. All rights reserved. 1701G 12-06
NOTE - If the key is left in the ignition switch after ignition is OFF and the programmable feature "Prevent door locking if key is left in ignition" (Feature 4) is ON, then the 1701G module will ignore this input. WHITE/BLUE (-) remote start input: See page 8 regarding wiring for application A or B A: For an alarm or keyless entry system installation on a vehicle OEM remote start equipped already. Connect this wire to the channel 3 or Auxiliary output of the security system in order to remote start or stop the vehicle NOTE – This input can be used in this way if the programmable feature OEM Remote Start (Feature 5) is set EQUIPPED and the car is OEM Remote Start enabled (it has the remote start button on the OEM remote). This setting is used when the vehicle is OEM remote start equipped and you are using a security or keyless entry systems auxiliary channel to activate the factory remote start. In this case the (+) brown brake wire is inactive and blue/white status output wire from the 1701g is used to 'shunt' the aftermarket security systems sensors. B: For aftermarket remote start installations for vehicles NOT OEM remote start equipped. Connect this wire to “Status output” or ground while running output of the remote start module. NOTE – This input can be used this way if the programmable feature OEM Remote Start (Feature 5) is set NOT EQUIPPED. This setting is used when installing an aftermarket remote start and allows bypass to occur, allows the (+) brake output to operate and will shut the radio off after remote start has stopped and lock the doors in case the vehicle is programmed to unlock the doors upon removal. - As long as this input is active the 1701G will: - Monitor the engine (RPM) and activate RPM output on violet/white wire - Force the YELLOW ignition status output OFF - Read the external temperature and if this is less than +5C (+41F), the 1701G will activate and keep active any “cold weather” features built into the car after engine is on for 5 seconds. - During the active state of the remote start, the 1701G also detects any of the following conditions through CAN bus for activating the remote start shutdown brown + output:
- Brake ON - Reverse ON - Car speed > 0 - Parking brake not On (only for manual gear box) - RPM over 2000
BLUE/BLACK (-) disarm/unlock driver’s door input: Connect this wire to “unlock #30 common output” of the door lock harness or negative unlock output of the security system. The “unlock #87 normally open input” of the security system must be grounded. BROWN/BLACK (-) panic input: Connect this wire to (-) Horn Honk output of the security system. Set the Horn Honk output to Constant, or this may be connected to an auxiliary channel to activate OEM panic.
© 2006 Directed Electronics. All rights reserved. N1701G 12-06
LT. BLUE (-) disarm/unlock all doors input: Connect this wire to “(-) second unlock” of the keyless entry/security/remote start system. RED/WHITE (-) Glass/hatch/trunk release or power lift gate open/close (depending on model): Connect this wire to “(-) Channel 2 output” or an auxiliary output of the security system. If the vehicle is equipped with a power liftgate or glass, the first time you activate red/white input to release it will take 5-6 seconds for the module to 'learn' if the vehicle is equipped with a power lift gate or glass release and it will activate the power lift gate if equipped and if not it will operate the glass release. NOTE - After a valid activation of this input, the 1701G will artificially activate the “Glass/hatch/ trunk Status Output” dark blue wire in order to prevent the security system from triggering, in case that the trunk is not automatically released or opened by the user. This output will remain active as long as the glass/hatch/trunk remains opened. If the glass/hatch/trunk is not opened this output will remain active a predefined time (30 seconds), to simulate the factory auto-relock future, or until a disarm/unlock or arm/lock input is received. This only occurs while armed/locked. LT. BROWN (+) remote start shutdown output: Connect this wire to a positive shutdown brake input of the remote start module. NOTE: This output is ONLY active when feature #5 is set to OEM REMOTE START NOT EQUIPPED and negative status input is active. This is the feature used when adding an aftermarket remote start system. This wire is not used if the vehicle is OEM remote start equipped. BLUE/WHITE (-) remote start status output: This wire is ONLY used if the vehicle is OEM remote start equipped while installing a security system. Connect this wire to “(-) instant trigger input (trunk input/shunt) Zone 1” of a Directed security system through a diode (see diagram A on page 8) in order to bypass the auxiliary sensors during an active remote start. Set the channel 3 of the security system as REMOTE START REPORTING if the system is a directed system and has this as a programming option for CH3. NOTE – This output can be used this way if the programmable feature OEM Remote Start (Feature 5) is set EQUIPPED and the car is OEM remote start enabled (it has the remote start button on the OEM remote). WHITE (-): Not used for this application. YELLOW (+) ignition status output: (not used for aftermarket remote start installations) Connect this wire to the “ignition input” of the security system 200 mA output maximum. NOTE - The ignition output will be inactive during the remote start operation in order for the security system to not be triggered. DARK GREEN (-) door status output: Connect this wire to the “(-) door trigger input” of the security system. LT. GREEN CAN bus wire : Connect this wire to the CAN wire in the car light green pin #1 of the OBD2 connector. NOTE - This must be a soldered connection as far away from the diagnostic connector as possible. DO NOT interrupt this wire.
© 2006 Directed Electronics. All rights reserved. 1701G 12-06
DARK BLUE (-) Glass/hatch/trunk status output: Connect this wire to the “(-) instant trigger input (trunk input/shunt)” of the security system. NOTE – This output will be artificially activated by the 1701G when trunk release input is activated from the security system while in armed state, in order to prevent the security system from triggering, in case that the trunk is not automatically released or opened by the user within a predefined time (usually 5 seconds). This output will remain active as long as the trunk remains opened. If the trunk is not opened this output will remain active a predefined time (30 seconds), to simulate the factory auto-relock feature, or until a disarm/unlock or arm/lock command is received on the inputs or read on the CAN bus by the 1701G. – This output will be artificially deactivated by the 1701G when the trunk release button is pressed on the original remote of the car while in armed state, in order to prevent the security system from triggering, in case that the trunk is automatically released or opened by the user. This output will remain inactive as long as the trunk remains opened. If the trunk is not opened this output will remain inactive a predefined time (30 seconds), to simulate the factory auto-relock feature, or until a disarm/unlock or arm/lock command is received on the inputs or read on the CAN bus by the 1701G. ORANGE/WHITE – bypass output: Connect this wire only if a immobilizer bypass is needed for GM cars. See diagram B for detail, this wire is NOT needed on OEM remote start equipped vehicles.
Powering up the 1701G After all connections have been made, plug in the module and the LED will report software version then flash at a slow rate waiting the ignition to turn on to identify the vehicle.
Once you turn the key on, 1701G will make the following steps:
- checks if the platform of the car is recognized ( max 10 sec ); then after the vehicle is recognized the LED will go solid indicating a successful learn. When ignition on is detected, the module will provide a (+) accessory output on the orange/white bypass wire similar to an accessory output while the module learns the vehicle. During normal operation, the 1701G enters sleep mode if no input is active or no CAN bus activity is detected for more than 4 sec. When the 1701G is in sleep mode the LED is OFF; when the 1701G is not in sleep mode the LED is ON. This is a method to verify proper operation of the 1701G module. NOTE: For NON-OEM equipped remote start vehicles where you are using the orange/white bypass wire, you MUST plug in the module after all connections are finished. After a failed initialization phase, the 1701G will switch off the LED for 5 seconds. Then it will flash shortly either once or twice indicating a failed learn.
Feature Programming The feature programming routine is used to access and change any of the feature settings. The feature settings can be accessed and changed by using the button and LED on the unit to enter the feature programming routine. To enter feature programming routine 1. Turn the ignition on and then off.
© 2006 Directed Electronics. All rights reserved. N1701G 12-06
2. Within 5-seconds, press the programming button corresponding to the feature number you want to change. 3. After a 3 second pause, the LED will blink the corresponding number of times you pressed the button confirming the programming feature 1-9 you wish to change, pause and confirm again for up to 15 seconds. 4. Press and hold the Programming button and the LED will flash a number of times equal to the current settings of the selected feature either once or twice. The module will toggle between the two settings automatically while the button is held. 5. Release the button when the desired setting is selected.
- The Learn Routine can be exited by
- Turning the ignition On or
- No activity for 15-seconds.
Feature Feature (Default setting in BOLD) Number 1 ZAP (Reset) 2 Auto-lock with Speed 3 Auto-unlock with key removed Prevent Door Locking if Key left in ignition 4 5
OEM remote start
1 Blink
2 Blinks
Off Off On On
On/ZAP (reset) On Off Off
Off/NOT Equipped
On/Equipped
Programming features setting guide The following programmable features are proposed to be implemented for 1701G module: 1. ZAP – OFF / ON ( default – OFF ) When this option is ON, 1701G will automatically restore default programmable features. When this option is set to OFF (default) all programmable features are left as they were programmed last. 2. Factory auto-lock – ON / OFF ( default – OFF ) When this option is ON, 1701G will automatically lock the doors and the trunk when the vehicle speed becomes greater than 12 mph, but when this option is OFF, 1701G will not take any automatic action for auto-locking with speed. 3. Factory auto-unlock – ON / OFF ( default – ON ) When this option is ON, 1701G will automatically unlock the doors and the trunk when the ignition key is taken out from the ignition switch. NOTE: This feature is useful when a vehicle is NON OEM remote start equipped if the customer wishes to have auto unlock upon removing the key from the cylinder but when installing an aftermarket alarm this can unlock the door upon remote start shutdown. This retains the feature without unlocking the doors upon remote start shutdown. Be sure to turn the vehicles auto unlock function OFF if this feature is used. © 2006 Directed Electronics. All rights reserved. 1701G 12-06
When this option is OFF, 1701G will not take any automatic action for auto-unlocking. 4. Prevent Door Locking if Key left in Ignition ON/OFF ( default – ON ) When this option is ON, 1701G will not lock the doors when the ARM/LOCK input is received and the key is left in the ignition. 5. OEM remote start - OEM EQUIPPED / Not OEM EQUIPPED ( default - Off/Not OEM EQUIPPED) When this option is set to EQUIPPED, the 1701G will use white/blue input as a remote start trigger input and blue/white output will operate as a negative status output/ground while running output. Brown + brake shutdown will not be active in this case and is not used. When this option is programmed to NOT OEM remote start equipped (default) the 1701G will use white/blue input as a negative status input and Brown + brake output wire will have all the functionality associated with these signals. In this case Blue/white output will not be used.
Version Report 1701G software version When the 1701G module is powered, the LED will indicate the software version: Software Version Example: Version 1.2.3 The LED will flash 1 time, then 1 second pause, then flash 2 times, then 1 second pause, then flash 3 times, then a 2 second pause, then the initialization routine will continue.
© 2006 Directed Electronics. All rights reserved. N1701G 12-06
Trunk/Glass Release/Power Liftgate open/close
Remote Start (OEM Equipped)
Immobilizer Bypass (if not OEM remote start equipped)
Autolock with speed (12 MPH)
Autounlock at key out
Panic function input available
Ignition Status Output
Door Trigger Output
Hood Output (if OEM Equipped)
Trunk/Hatch trigger output
RPM (tach) output
Brake Output
Reverse Detection (note 2)
Car Speed (note 3)
Rear Defroster (if applicable) (note 4)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√ (1)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
N/A
√
√ (5)
√
√
√
√
√
√
N/A
√
√
√
√
√
√
√
N/A
√
√
√
√
√
√
√
√
N/A
√
√
√
√
√
√
√
√
√ (1)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√ (1)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
2007 GMC Sierra
√
√
√
N/A
√
√
√
√
√
√
√
√
N/A
√
√
√
√
√
2007 GMC Yukon
√
√
√
√ (1)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Disarm/Unlock Driver door
√
Arm/Lock all doors
Disarm/Unlock All Doors
FEATURE Chart
2007 Buick Lucerne
√
√
2007 Cadillac DTS
√
√
2007 Cadillac Escalade
√
√
2007 Chevy Avalanche
√
2007 Chevy Silverado
√
2007 Chevy Suburban 2007 Chevy Tahoe
Features; 1 - trunk release will operate as power liftgate open/close if equipped (the module learns the first time you operate), otherwise it will operate glass or trunk release. 2 - during remote start if NON OEM equipped, the unit will send a positive pulse through the brown brake if reverse is detected during run time. 3 - during remote start if NON OEM equipped, the unit will send a positive pulse through the brown brake if any speed is detected during run time. This is also used for auto lock with speed. 4 - rear defroster will activate below +41 degrees F (+5 degrees C) 5 - some models may not work. For these models use a 556UW.
© 2006 Directed Electronics. All rights reserved. 1701G 12-06
DIAGRAM A OEM remote start equipped vehicle, installing a security system to OEM remote start using an aux channel
White/blue Aux channel out
Directed Security System
feature 5 set to OEM remote start equipped input White/blue Brown
N/C Blue trunk input
N/C, not connected
1701G
Blue/white - status output
* note 1
Orange/white + output
Dark blue - trunk output
note 1: On this wire, if the vehicle is remote started using OEM Remote while armed, this will trigger the alarm. If you are using a 2-way alarm, if you are the system while remote started, the trunk icon will apear, this in normal
DIAGRAM B NON OEM equipped remote start install wiring feature 5 set to NON OEM remote start equipped Blue - status output
Directed Remote Start System
input White/blue
Brown + brake input
+ Brown shutdown output N/C
Immobilizer green plug, accessory wire is pin 2 either brown or yellow
OUT
Blue/white
1701G
Orange/White, Bypass output
Cut Wire
X
X
Red/White, (12v wire) Pink, (Ignition)
BCM
Brown, (Accessory) White, (unused)
Key Cylinder
Pink/Black (note 2)
+ Accessory Wire
9.6k resistor
87 85
87A 30
86
6.3k resistor
12v fused + Ignition Wire + 2nd Accessory Wire
Remote Start Relays
+ Start Wire - Status Output
note 2: White/black for Lucerne and DTS
© 2006 Directed Electronics. All rights reserved. N1701G 12-06
WIRING DIAGRAM
1701G
LED LED Programming Programming button button
Harness connector Harness connector (+) igniton output (+) igniton output (-) door trigger output (-) door trigger output (BUS-Wire) can bus data (BUS-Wire) can bus data (-) hatch/trunk trigger output (-) hatch/trunk trigger output (+) bypass output (+) bypass output
YELLOW YELLOW DK. GREEN DK. GREEN LT. GREEN LT. GREEN DARK BLUE DARK BLUE ORANGE/WHITE ORANGE/WHITE
WHITE WHITE BLUE/WHITE BLUE/WHITE LT. BROWN LT. BROWN RED/WHITE RED/WHITE
Not used Not used (-) status output (note 1) (-) status output (note 1) (+) brake output (note 2) (+) brake output (note 2) (-) glass/hatch/trunk release or open input (-) glass/hatch/trunk release or open input
18 18 17 17 16 16 15 15 14 14 13 13 12 12 11 11 10 10 99 88 77 66 55 44 33 22 11 (-) all door unlock input (-) all door unlock input (-) panic input (-) panic input
LIGHT LIGHTBLUE BLUE BROWN/BLACK BROWN/BLACK
(-) remote start input (-) remote start input
BLUE/BLACK BLUE/BLACK WHITE/BLUE WHITE/BLUE
(-) lock input (-) lock input
GREEN/BLACK GREEN/BLACK
(-) drivers door unlock input (-) drivers door unlock input
RED fused 12V input RED (+) (+) fused 12V input VIOLET/WHITE tachometer Output (AC) tachometer Output VIOLET/WHITE (AC) BLACK chassis ground BLACK (-) (-) chassis ground LT. hood status output LT.GRAY GRAY (-) (-) hood status output
NOTES: NOTES: (1)(1)Wire Wireisisinactive inactivewhen whenfeature feature55isisset settotoNON-OEM NON-OEMremote remotestart startequipped. equipped. (2)(2)Feature Featureisisonly onlyactive activewhen whenfeature feature55isisset settotoNON-OEM NON-OEMremote remotestart startequipped. equipped.
LIMITED ONE-YEAR CONSUMER WARRANTY For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security accessory product, Directed Electronics. (hereinafter “DIRECTED”) promises to the original purchaser, to repair or replace (at DIRECTED’s election) with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer in the United States; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name, date of purchase and complete product and Part description. This warranty is non-transferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or if the Part has been damaged by accident, abuse, unreasonable use, neglect, water, theft, improper service, installation or other causes not arising out of defect in materials or construction. This warranty is automatically void if any Part has had the serial number defaced, altered, or removed. This warranty is automatically void if the Part has had Repair Service performed by anyone other than the Directed Repair Department. This warranty does not cover damage to any Part caused by installation or removal of the Part or any system related thereto. This warranty does not cover labor costs for the removal or reinstallation of the Part. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT PERMITTED BY LAW; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
© 2006 Directed Electronics. All rights reserved. 1701G 12-06
