Transcript
pt2400 Professional Stereo Power Amplifier
FEATURES ● ●
● ● ● ●
●
● ● ●
● ●
●
Lightweight- 48 lbs. Fully modular dual monaural design (from power switch to AC line cord). High efficiency (50% input to output). Positive locking detachable dual AC line cords. Compact - only 12.75” deep. Rugged, quiet, 100 CFM thermally controlled cooling system. Compression circuit for long term excessive high frequency signals. Remote sequential power on/off feature. Clipping eliminator circuit. Protection Features: Short circuit Excessive high frequency Thermal Clipping eliminator DC offset Soft start/Input mute Separate L/R AC line fuses Controls Dual power switches Dual sequence switches Dual 11 detents level controls XLR phasing switch Series mono switch Dual mono switch Clipping eliminator switch Ground lift CSA, CE approved
18 0 DAY
Performance Guarantee 9300 North Decatur
●
Portland OR 97203
●
Tel: 503.978.3344
●
Made In America
Fax: 503.978.3302
5 Year Warranty
Carver Professional, a division of Phoenix Gold International, Inc.
Power Output: Both channels driven (20Hz-20kHz) 8 ohm/ch. 750 watts 4 ohm/ch. 1200 watts 2 ohm/ch. 1500 watts Power Output: Series mono operation (20Hz-20kHz) 8 ohm 2400 watts 4 ohm 3000 watts
Size (HxWxD):
5.25” (3u) x 19” x 12.75” (133mm x 483mm x 324mm)
34dB
Net Weight:
48 lbs. (21.8 Kgs.)
15 Kilohms Unbalanced 30 Kilohms Balanced
Shipping Weight:
59 lbs. (26.8 Kgs.)
Damping Factor:
>200 @ 1kHz
Sensitivity:
1.5 V rms
Gain: Input Impedance:
Signal to Noise Ratio: >100dB (from rated power @ 4Ω/A weighted)
CMRR: >70db @ 1kHz Maximum Current Draw: 40 A (4Ω rated power)
Frequency Response: 20Hz to 20kHz ±0.5dB
Display:
7 LED indicators per channel, 1 green on, 5 yellow signal, 1 red clip/protect
Channel Seperation: >55db @ 1kHz Slew Rate:
25V/µs
Cooling:
THD: (at 1200W)
4Ω 20-20kHz < 0.5%
ConnectionsInput: Output:
IM Distortion:
<0.1%
Rear to front w/100 CFM maximum XLR, barrier strip 5-way binding posts, 2 sets/channel
Features and specifications are subject to change without notice.
Limited Warranty Carver Professional provides a limited warranty on all amplifiers (free of manufacturing defects in materials and/or workmanship) to the original consumer/purchaser for a period of 5 years when purchased from an authorized Carver Professional dealer. Please consult your dealer or the factory for specific warranty information.
pt2400 Architects’ and Engineers’ Specifications The power amplifier being of two channels, shall deliver 750 W into 8Ω per channel, 1200 W into 4Ω per channel. The amplifier shall be capable of providing 1200 W per channel into a 70 volt distribution system without the need for stepup transformers. The amplifier being of two completely independent power supplies per channel shall be capable of operating from separate AC branch circuits and to provide independent operation with the exception of the series (bridge-mono) mono and the parallel mono operation. The amplifier shall be capable of series bridge-mono operation thereby providing 2400 W RMS output into 8Ω. The amplifier shall have a thermal shutdown system to protect the power devices from over-temperature operation. This thermal protection system shall be self-resetting. The amplifier shall provide input limiting to protect the output devices against short circuits or against non-musical excessive high frequency signals. Each amplifier shall independently shut down to protect against DC offset present at the outputs, or an internal power supply fault. The amplifier shall have slow start-up and muted inputs on turn-on. The amplifier shall have a voltage gain of 34 dB. Noise shall be at least -100 dB below 1200 W/4Ω, A-weighted, from 20Hz-20kHz. Total harmonic distortion shall be less than 0.5% and intermodulation distortion shall be less than 0.1%. The frequency response shall be less than ±0.5 dB, 20Hz-20kHz. The front panel controls shall consist of per channel: one level control, one master power switch and one sequence switch. The rear panel connectors shall consist of per channel: 3 input barrier terminals, one 3-pin locking input connector, two sets of dual bind post output connectors,
9300 North Decatur
●
two barrier sequence terminals and one positive locking AC power cord. The amplifier shall provide input configuration switches to allow in-rack selection of dual mono, series mono, clip eliminator and 3-pin polarity configuration. A cooling fan with removable filter shall operate on two speeds that is determined by the heat sink temperature. The dimensions shall allow for standard 19” EIA rack mounting. It shall be 5.25” high and 12.75” deep. The amplifier shall weigh 48 pounds. The maximum input current requirements per channel for a 1200 W output into 4Ω shall be 20 amps at 120V, 60Hz. The power amplifier shall be a CARVER Professional pt2400.
Portland OR 97203
●
Tel: 503.978.3344 ● Fax: 503.978.3302
