Transcript
IMPORTANT: - Do not mix old and new batteries - Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, nimh, etc) batteries
INSTRUCTIONS & WARRANTY MODEL# 70034 Thank you for your purchase of this quality clock. The utmost care has gone into the design and manufacture of your clock. Please read these instructions carefully and store them in a safe place for future reference. PRODUCT DESCRIPTIONS 1. SNOOZE / LIGHT bar 2. LCD display 3. TIME /CALENDAR & 12/24 HOUR set button 4. ALARM 1 / ALARM 2 set button 5. ALARM 1 ON/OFF button 6. ALARM 2 ON/OFF button 7. ADJUST button
8. CHANNEL button 9. MIN / MAX button 10. °C/°F & SEARCH button 11. BATTERY compartment 12. FOLD OUT STAND 13. RESET button
INSTALLING OR REPLACING THE BATTERIES (FOR THE WIRELESS OUTDOOR TEMPERATURE SENSOR) Note: The wireless sensor comes installed on the optional mounting bracket. 1. Remove the sensor from the bracket by holding the back of the bracket in one hand and with your other hand pull the sensor away from the bracket. 2. Remove the battery compartment cover located on the back of the sensor by sliding the cover in the direction of the arrow marked on the cover. 3. Install two fresh alkaline “AA” size batteries into the battery compartment. Make sure the polarity is correct by following the (+ or -) symbols engraved inside. 4. Replace the battery compartment cover. The sensor should then be reattached to the mounting bracket IMPORTANT: Extended storage can cause batteries to leak and damage the unit. Leaky batteries should be discarded immediately. Skin burns or other personal injury can result. Always dispose of batteries according to federal, state and local regulations.
TOP OF CLOCK
IMPORTANT: - Do not mix old and new batteries - Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, nimh, etc) batteries SETTING THE TIME & YEAR 1. Press and hold the TIME / CALENDAR set button located on the front of the clock for 3 seconds to enter the TIME and CALENDAR setting mode. The hour digit will begin to flash indicating your are in the time setting mode. 2. Intermittently pressing and releasing the ADJUST button will advance the hour for the time of day in one hour increments. Press the ADJUST button as necessary until the correct hour is displayed. Note: If you are in the 12 hour time format, be sure you are in the correct AM or PM time period. When the “PM” indicator appears on the display, the time displayed is in the 12 hour period between 12:00 noon and midnight.
FRONT OF CLOCK
3. Press the TIME / CALENDAR button to exit the hour setting and enter the minute setting mode. 4. Intermittently pressing and releasing the ADJUST button will advance the minute for the time of day in one minute increments. Press the ADJUST button as necessary until the correct minute is displayed. 5. Press the TIME / CALENDAR button to exit the minute setting and enter the year setting mode. 6. Intermittently pressing and releasing the ADJUST button will advance the year in one year increments. Press the ADJUST button as necessary until the correct year is displayed. 7. Press the TIME / CALENDAR button to exit the year setting and enter the month setting mode.
BACK OF CLOCK LCD DISPLAY ICONS / DESCRIPTIONS 1. DAY OF THE WEEK 2. DATE 3. MONTH 4. ALARM ON indicators 5. ALARM TIME indicator 6. ALARM TIME
7. AM / PM indicators 8. TIME 9. CHANNEL indicator (for wireless sensor) 10. LOW BATTERY indicator (for wireless sensor) 11. OUTDOOR TEMPERATURE 12. INDOOR TEMPERATURE
8. Intermittently pressing and releasing the ADJUST button will advance the month in one month increments. Press the ADJUST button as necessary until the correct month is displayed. 9. Press the TIME / CALENDAR button to exit the month setting and enter the date setting mode. 10. Intermittently pressing and releasing the ADJUST button will advance the date in one day increments. Press the ADJUST button as necessary until the correct date is displayed. Note: The day of the week will automatically set according to the month, date, and year. 11. Press the TIME / CALENDAR button to exit setting mode. Note: If no settings are made within 30 seconds, the clock will exit the setting mode and automatically return to the normal time display mode. If this happens, you will need to start the setting procedure again from step 1. SETTING THE ALARM TIME Note: The clock has two alarms. Be sure you are setting the correct alarm by checking the ALARM TIME indicator “Alarm 1” and “Alarm 2” above the alarm time display. Only one alarm time indicator will be shown at a time. 1. Select the alarm you wish to set by pressing the ALARM 1 / ALARM 2 button located on the front of the clock to select one of the two alarms. 2. Press and hold the ALARM 1 / ALARM 2 button for 3 seconds to enter the ALARM TIME setting mode. The hour digit will begin to flash indicating your are in the alarm time setting mode.
The following instructions explain how to operate your Westclox digital alarm clock. INSTALLING OR REPLACING THE BATTERIES (FOR THE CLOCK) 1. Remove the battery compartment cover located on the back of the clock by using your index finger to gently pull down on the latch until you feel the cover release and open. 2. Install three fresh alkaline “AA” size batteries into the battery compartment. Make sure the polarity is correct by following the (+ or -) symbols engraved inside. 3. Replace the battery compartment cover. IMPORTANT: Extended storage can cause batteries to leak and damage the unit. Leaky batteries should be discarded immediately. Skin burns or other personal injury can result. Always dispose of batteries according to federal, state and local regulations.
3. Intermittently pressing and releasing the ADJUST button will advance the hour for the alarm time in one hour increments. Press the ADJUST button as necessary until the correct hour is displayed Note: If you are in the 12 hour time format, be sure you are in the correct AM or PM time period. When the “PM” indicator appears on the display, the time displayed is in the 12 hour period between 12:00 noon and midnight. 4. Press the ALARM 1 / ALARM 2 button to exit the hour setting and enter the minute setting mode. 5. Intermittently pressing and releasing the ADJUST button will advance the alarm minute in one minute increments. Press the ADJUST button as necessary until the correct minute is displayed. 6. Once the desired alarm time is set press the ALARM 1 / ALARM 2 button to exit the alarm setting mode.
