1997-up Ford Econoline/club Wagon

Transcript

TUNERS / CASSETTE / DISC PLAYERS MINI STAN DIN ISO DIN SINGLE DBL DIN RADIO EQ STACK CHASSIS H 13/ 4-2 2 2 2 37/8 3 CHASSIS W 71/8 71/8 71/8 7 71/8 71/8 CHASSIS D 43/ 4-51/2 57/ 8-611/ 16 57/ 8-611/ 16 57/ 8-611/ 16 57/ 8-611/ 16 57/ 8-611/ 16 NOSE H 15/ 8-13/4 15/ 8-13/4 23/8 113/ 16 33/ 4-4 NOSE W 41/ 8-43/ 16 41/ 8-43/ 16 71/2 611/ 16 611/ 16-71/4 SHAFT SP. 51/ 8-53/4 51/ 8-6 UPDATED THROUGH '98 '99 2000 2001 Van IN DASH APPLICATION NOTES KS KS KS KS APPLICATION KIT MODEL: HARNESS ADAPTOR: FORD 1997-UP ECONOLINE/ CLUBWAGON K4 N FD1300 FD02 ANTENNA ADAPTOR: IN-DASH INSTALLATION AREA DIMENSIONS MAX DEPTH DEPTH 7" CAVITY DASH OPENING WIDTH 7 /2" 7" PLASTIC 4" 1 7 /2" TYPE: FORD DOUBLE DIN DASH MATERIAL: HEIGHT 1 THICKNESS: 4" 1 /8 " REMOVE REAR SUPPORT MODIFY CAVITY FOR MAX DEPTH AMPLIFIER/EQ MOUNTING LOCATIONS UNDER/IN DASH UNDER SEAT 16 x 5 x 12" GLOVE BOX (WxHxD) TRUNK/ CARGO Various NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR. Dimensions shown are inches. For inch/mm conversions refer to chart section. DASH. B C1 C2 D D1 D2 D3 F1 F2 K K1 K2 K3 K4 = = = = = = = = = = = = = = K 5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER. K S = SCOSCHE KIT RECOMMENDED. N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED. P = PERFECT WITHOUT MODIFICATION. P 1 = MODIFY OR REMOVE POCKETS. P 2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT). P 3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT. R = REAR LOAD ISOMOUNT. U = UNDERDASH. W 1 = WITH POWER WINDOWS ONLY. W 2 = WITHOUT POWER WINDOWS ONLY. BACK UP PLATES REQUIRED. CUT TRIM/PLASTIC (STRUCTURE). CUT STEEL. BELOW DECK ONLY. LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT). CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK. NARROW SURFACE, BELOW DECK ONLY. MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING. MODIFY DASH CAVITY AND/OR PANEL. INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED. KIT MODIFICATIONS REQUIRED. EXTENSION KIT RECOMMENDED. WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO. FABRICATE PANEL/BRACKETS. 101 © 1997-UP FORD ECONOLINE/CLUBWAGON VAN DASHWITH SCOSCHE FD1300 KIT AND AFTERMARKET CD PLAYER INSTALLED. PRELIMINARY: FRONT DOOR LOCATIONWITH SCOSCHE SA68 SPEAKER ADAPTER INSTALLED. DISCONNECT THE NEGATIVE BATTERY CABLE. ANTENNA: THE FACTORY ANTENNA IS LOCATED ON THE TOP OF THE RIGHT FRONT FENDER. RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS FOR A FORD DOUBLE DIN STYLE RADIO. AN INSTALLATION KIT IS NECESSARY WHEN USING AN AFTERMARKET RADIO. WE RECOMMEND THE USE OF A SCOSCHE FD1300 KIT. 1. USING THE FORD DIN REMOVAL TOOL CAREFULLY INSERT THEM INTO THE HOLES ON THE OUTSIDE EDGES OF THE RADIO TO RELEASE THE RADIO AND PULL IT OUT OF THE DASH CAVITY. 2. UNPLUG ALL CONNECTORS AND REMOVE THE RADIO. FRONT DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 X 8" FORD STYLE SPEAKER. 1. POP OFF SMALL INSIDE MIRROR COVER TRIANGLE AND REMOVE ONE SCREW FROM THAT LOCATION. 2. REMOVE COVER CAP AND EXTRACT (1) SCREW FROM BEHIND IT AT THE LOWER REAR CORNER OF THE DOOR PANEL. 3. POP OUT DOOR RELEASE PLASTIC CUP AND REMOVE (1) SCREW FROM BEHIND. 4. POWER MODELS: POP OUT POWER WINDOW/LOCK SWITCH PANEL, UNPLUG, AND REMOVE. NON POWER MODELS: POP OFF PLASTIC TRIM COVER OF WINDOW CRANK AND REMOVE THE T-20 TORX SCREW HOLDING THE CRANK ON. 5. LIFT PANEL UP AND AWAY FROM DOOR TO REMOVE. 6. EXTRACT THE (4) SCREWS SECURING THE SPEAKER TO THE ADAPTER, PULL THE SPEAKER FROM THE CAVITY, UNPLUG THE LEADS AND REMOVE. FRONT DOOR 6 X 8" SPEAKER PROVISION. REAR (TAILGATE) DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 X 8" FORD STYLE SPEAKER. 1. EXTRACT (2) SCREWS FROM UNDER THE DOOR PULL HANDLE. 2. UNSNAP DOOR RELEASE PLASTIC TRIM CUP. 3. USE A PANEL REMOVAL TOOL TO CAREFULLY PRY OUT ON THE EDGES OF THE DOOR PANEL TO RELEASE THE PANEL CLIPS. 4. RELEASE CLIPS HOLDING THE POWER WINDOW SWITCH PANEL, UNPLUG AND REMOVE. 5. LIFT PANEL UP AND AWAY FROM DOOR TO REMOVE. 6. EXTRACT THE (4) SCREWS SECURING THE SPEAKER TO THE ADAPTER, PULL THE SPEAKER FROM THE CAVITY, UNPLUG THE LEADS AND REMOVE. TAILGATE DOOR 6 X 8" PROVISION. 102 © 1997 SCOSCHE INDUSTRIES, INC.