Transcript
SB-LR-4/10TW3 INSTR_SKU# 011375
If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox® be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s). 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.
I N S TA L L AT I O N G U I D E for the
SB-LR-4/10TW3
SKU# 94600 2004-2009 Land Rover LR3, & 2009 & Up Land Rover LR4
Enclosure Type: Driver Type: Nominal Impedance: Continuous Power Handling:
Sealed 10TW3-D4 2 ohms 400 watts (RMS method)
INSTALLATION DIFFICULTY:
2
OUT OF
5
ESTIMATED TIME: 1 HOUR
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure. We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide completely before beginning the process.
Continued on Next Page
SB-LR-4/10TW3 INSTR_SKU# 011375
I N C L U D E D H A R D WA R E
Page 2 • JL Audio, Inc., 2015
Continued on Next Page
SB-LR-4/10TW3 INSTR_SKU# 011375
P O W E R R E C O M M E N D AT I O N JL Audio recommends high quality amplifiers such as the JL Audio XD300/1. The diagram below shows the recommended crossover settings for the XD300/1. For a detailed description of the amplfiier settings, consult the owner’s manual for the amplifier. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier.
CONNEC TIONS Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplifier. Other kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplifier. JL Audio reccomends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25. Page 3 • JL Audio, Inc., 2015
Continued on Next Page
SB-LR-4/10TW3 INSTR_SKU# 011375
Page 4 • JL Audio, Inc., 2015
STEP 1
STEP 5
Empty out the cargo area of the vehicle.
Remove the factory nut from the stud.
STEP 2
STEP 6
Remove the A/C service door at the rear of the driver’s side panel. Locate the factory hole indicated.
Secure the Upper Bracket to the Lower Bracket using a pair of 1/4 - 20 Flange Bolts and 1/4 - 20 Flange Nuts as shown.
STEP 3
STEP 7
Slide a 3/8 - 16 U-Nut over the factory hole as shown.
Slide the Upper Bracket over the factory stud and secure with the factory nut as shown.
STEP 4
STEP 8
Locate the factory stud indicated.
Slide a 3/8” Lock Washer and a 3/8” Flat Washer over the 3/8 - 16 x 1-1/4” Hex Bolt, and thread the assembly through the hole in the Lower Bracket and into the 3/8 - 16 U-Nut as shown, and firmly tighten.
Continued on Next Page
SB-LR-4/10TW3 INSTR_SKU# 011375 STEP 9
S T E P 13
Pictured are the Upper and Lower Brackets installed.
Connect speaker cable to the terminal cup on the back of the enclosure, and reinstall the Stealthbox®. Slide a 3/8” Flat Washer, a 3/8” Lock Washer, and a 3/8 - 16 Hex Nut over each of the 3/8 - 16 x 2-1/4” Set Screws, and firmly tighten. Route speaker cable as necessary.
S T E P 10
S T E P 14
Slide a 3/8 - 16 U-Nut over the large hole in the Upper and Lower Brackets. Thread a 3/8 - 16 x 2-1/4” Set Screw into each 3/8 - 16 U-Nut as shown.
Reinstall the subwoofer and the cargo liner.
S T E P 11 Remove the subwoofer from the Stealthbox®, and place the enclosure into position in the vehicle, allowing the two 3/8 - 16 x 2-1/4” Set Screws to pass through the two openings in the back of the enclosure.
S T E P 12 If the vehicle is equipped with the rubber cargo liner, it will need to be cut for proper fitment and easy removal. Use the enclosure as a guide to mark the cargo liner. Remove the enclosure and the cargo liner, and cut the cargo liner on the mark. Pictured is the rubber cargo liner after cutting.
Page 5 • JL Audio, Inc., 2015
Continued on Next Page
SB-LR-4/10TW3 INSTR_SKU# 011375 C O N G R AT U L AT I O N S ! You have completed the installation for this model! Enjoy your new Stealthbox®!
M I D/ H I G H F R E Q U E N C Y D R I V E R F I T M E N T A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle. Front Speaker Size / Location: 6-1/2”- Front Doors Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-650, C5-650x, C5-650, & ZR650-CSi Rear Speaker Size / Location: 6-1/2”- Rear Door Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-650, C5-650x, C5-650, & ZR650-CSi
How we play.™ (954) 443-1100
w w w. j l a u d i o . c o m
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.,. “Ahead of the Curve”, its respective logo, and “How we play” are trademarks of JL Audio, Inc.,. Printed in USA • ©2013 JL Audio, Inc.,. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online at www.jlaudio.com.
JLA-SKU# 94600 • ver. 10.07.2015 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
Page 6 • JL Audio, Inc., 2015
