Transcript
SB-H-PLT/10TW3 INSTR_SKU# 011365
I N S TA L L AT I O N G U I D E for the
SB-H-PLT/10TW3 SKU# 94576 2009 & Up Honda Pilot
If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox® be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s). 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.
INSTALLATION D I F F I C U LT Y:
25 OUT OF
ESTIMATED TIME: 1 HOUR
SPECIFICATIONS Enclosure Type: Sealed Driver Type: 10TW3-D4 Nominal Impedance: 2 ohms Continuous Power Handling: 400 watts (RMS method)
INCLUDED HARDWARE (3) 1/4 - 20 x 1” Bolt (3) 1/4” Lock Washer (3) 1/4” Flat Washer (1) Carpet
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide completely before beginning the process.
Continued on Next Page
SB-H-PLT/10TW3 INSTR_SKU# 011365
POWER RECOMMENDATION JL Audio recommends high quality amplifiers such as the JL Audio XD300/1. The diagram below shows the recommended crossover settings for the XD300/1. For a detailed description of the amplfiier settings, consult the owner’s manual for the amplifier. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier.
CONNECTIONS Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplifier. Other kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplifier. JL Audio reccomends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25. Page 2 • JL Audio, Inc., 2013
Continued on Next Page
SB-H-PLT/10TW3 INSTR_SKU# 011365
Page 3 • JL Audio, Inc., 2013
STEP 1
STEP 5
Empty out the cargo area of the vehicle and fold the rear seats down.
Measure and mark 2” up from the bottom and 1-1/4” to the right of the second large rib. Using a 1/8” drill bit, drill a pilot hole on the intersection of the two marks.
STEP 2
STEP 6
Lift and remove the floor cover panel. Remove the jack tools from the plastic tray, then carefully unclip and remove the tray.
Pictured are the locations of the two pilot holes.
STEP 3
STEP 7
On the rear driver’s side of the plastic tray, measure and mark 2” from the bottom.
On the front driver’s side of the plastic tray, measure and mark 3-5/8” from the bottom.
STEP 4
STEP 8
Measure and mark 1” to the right of the first rib. Using a 1/8” drill bit, drill a pilot hole on the intersection of the two marks.
Measure and mark 1-7/8” to the right of the rib. Using a 1/8” drill bit, drill a pilot hole on the intersection of the two marks.
Continued on Next Page
SB-H-PLT/10TW3 INSTR_SKU# 011365
STEP 9
STE P 13
Pictured is the location of the pilot hole.
Measure and mark 3-1/2” from the top of the tray.
Enlarge all three holes to 3/8”.
STEP 10
STE P 14
Place the Stealthbox® into position in the driver’s side of the plastic tray, and apply a piece of tape on the front side of the tray to mark the edge of the enclosure.
Measure and mark 5-1/2” from the driver’s side.
S T E P 11
STE P 15
Remove the Stealthbox® from the tray.
Place the Stealthbox® back into position inside the plastic tray.
Pictured is the section of the plastic tray that needs to be cut. Use the dimensions given in Steps 12-14 to mark the tray as shown.
Page 4 • JL Audio, Inc., 2013
Cut out the section of the plastic tray shown in Step 11.
Slide a 1/4” Lock Washer and a 1/4” Flat Washer over each of the 1/4 - 20 x 1” Bolt, and thread an assembly through each of the holes drilled in the plastic tray and into the inserts in the enclosure. Pictured is the rear of the plastic tray with the hardware installed.
S T E P 12
STEP 16
Measure and mark 1” to the left of the tape.
Pictured is the front of the plastic tray with the section removed and the hardware installed.
Continued on Next Page
SB-H-PLT/10TW3 INSTR_SKU# 011365
S T E P 17
CONGRATULATIONS!
Place the Carpet into the vehicle as shown. You have completed the installation for this model! Enjoy your new Stealthbox®!
STEP 18 Connect speaker cable to the barrier strip on the Stealthbox®, reinstall the plastic tray, and route the cable as necessary. Reinstall the floor cover panel.
MID/HIGH FREQUENCY DRIVER FITMENT A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle. Front Speaker Size / Location: 6-1/2”- Front Doors Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-570, C5-650x, C5-650, & ZR570-CSi Rear Speaker Size / Location: 6-1/2”- Rear Door Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-650, C5-650x, C5-650, & ZR570-CSi
(954) 443-1100
w w w. j l a u d i o . c o m
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.,. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.,. JLA-SKU# 94576 09.18.2013 • Printed in USA • ©2013 JL Audio, Inc.,. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online at www.jlaudio.com.
Page 5 • JL Audio, Inc., 2013
1 0 3 6 9
N O R T H
C O M M E R C E
PA R K WAY
•
M I R A M A R ,
F L O R I D A
•
3 3 0 2 5
•
U S A
