Preview only show first 10 pages with watermark. For full document please download

инструкция по установке_2

   EMBED

Share

Transcript

1、Connection Description: It is two connectors need to be connect. (1) The 24 Pin connector of the sample wire : Connect to the 24Pin connector which connected to the original car monitor. The 24Pin connector which connected to the original car monitor. (2) The 16 Pin connector of the sample wire： Connect to the 16 Pin connector of Sunnybright’s navigator. Sample wire connection schematic diagram： Monitor 24Pin connector Connect to the 24 pin connector witch show as above picture Connect to the 16 pin connector in navigator 16Pin connector 2、System diagram Non-Line-side A A13 A14 A15 A1 A2 A3 A4 A18 A19 A20 A5 A6 A7 A8 A21 A22 A9 A23 B13 B14 B15 A11 B1 B2 B3 B4 (非进线端视图 ) 导航 B A17 B17 B18 B19 B20 B21 B5 B6 B7 B8 B9 B22 B23 B11 2 4 6 8 10 12 14 16 2 4 6 8 10 12 14 16 1 3 5 7 9 11 13 15 1 3 5 7 9 11 13 15 TH16M C15 C14C13C12C11 C10 C9 C8 C7 C6 C5 C4 C3 C2 C1 1 2 3 4 5 B: Connect to 24 pin connector of front monitor A 转接原车到前屏24PIN A: Transfer the original car to 24 pin connector of front monitor TH16F J2 J3 A22 A11 A23 A1 A3 A14 A2 A13 DISP->IT IT->DISP UART_GND GND SIG_VCC SIG_GND INV_VCC INV_GND A9 A20 A8 A21 B 到前屏 24PIN B22 B11 B23 B1 B3 B14 B2 B13 DISP->IT IT->DISP UART_GND GND SIG_VCC SIG_GND INV_VCC INV_GND YS VP HP RGB_SYNC_GND B9 B20 B8 B21 YS VP HP RGB_SYNC_GND A5 A15 A4 COMP_IN(-) COMP_IN(+) COMP_IN_SHIELD B5 B15 B4 COMP_IN(-) COMP_IN(+) COMP_IN_SHIELD A17 A6 A18 A19 A7 R G B RGB_SYNC RGB_GND B17 B6 B18 B19 B7 R G B RGB_SYNC RGB_GND J3 driver board 15 pin J3 驱动板15PIN Navigator 导航 TH16F 5 4 6 8 7 1 2 RIN GIN BIN CSYNC VGND_RGB M_TXD M_RXD TH16M 5 4 6 8 7 1 2 RIN GIN BIN CSYNC VGND_RGB M_TXD M_RXD C1 C2 C3 C4 C5 C11 C12 C13 C14 C15 C6 C7 C8 C9 C10 CAR RED CAR GREEN CAR BLUE CAR SYNC GND RED GREEN BLUE SYNC GND NAVI RED NAVI GREEN NAVI BLUE NAVI SYNC GND J2 驱动板 5PIN E5 E4 E3 E2 E1 Connect this pin to +12V CCD control signal line. RXD TXD YS GND ACC J3 driver board 5