Transcript
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Installation Guide
CHALL
REMOTE STARTER XSTART
REMOTE CAR STARTERS AND ALARM INTERFACE CHALL
Index Vehicle Compatibility Chart.......................................................................................................................................... 02 CHTH1......................................................................................................................................................................... 03 CHTH2 (sold separately) - Vehicles 2004-2007 ......................................................................................................... 04 CHTH2 (sold separately) - Vehicles 2008 and Higher................................................................................................. 05 Updating the XSTART and RFTD Firmware................................................................................................................ 06 Programming the CHALL............................................................................................................................................. 08 Programming a 2-Way Remote................................................................................................................................... 09 Ready Mode................................................................................................................................................................ 10 Remote Start/Alarm Diagnostics.................................................................................................................................. 10 Programming the Available Features........................................................................................................................... 11 Feature Programming Chart........................................................................................................................................ 12 Warranty....................................................................................................................................................................... 13
Update Alert Firmware updates are posted to the web on a regular basis. It is tm important that you check for firmware and/or install guide updates prior to installing this product.
TECHNICAL SUPPORT / INFORMATION
web resources: www.xpresskit.com www.xpressvip.com www.directechs.com
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 2
• • • • • •
• • • • • •
•
•
•
•
•
• • • • • •
W W W W W W
• • • • • •
•
W
•
ST - Hand brake status
• • • • • •
• • • • • • • • • • •
ST - Brake status (foot brake)
• • • • • •
W W W W W W W W W W W
SS - Entry monitoring trunk/hatch pin
• • • • • •
• • • • • • • • • • •
SS - Entry monitoring hood pin
• • • • • • • • • • •
SS - Entry monitoring front door pins
• • • • • • • • • • •
SS - Entry monitoring driver door pin
• • • • • • • • • • •
• • • • •
SS - Entry monitoring ALL door pins
• • • • • • • • • • •
•
W W W W W
RS - Tach/RPM output
• • • • • • • • • • •
•
• • • • •
• • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
D D D D D
W W W W W
• •
• • • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • • •
D D D D D D D D D D D
W W W W W W W W W W W
• • • • • •
• • • • • •
• • • • • •
• • • • • •
• • • • • •
• • • • • •
D D D D D D
W W W W W W
•
•
•
•
•
•
D
W
RS - RAP shut down (remote ACC power)
• • • • •
PK - Push-To-Start ignition compatible
• • • • •
PK - Immobilizer BypassData no key req'd
• • • • •
KI - Key & ignition switch interface
• • • • •
DL - Trunk/hatch release
2
• • • • •
DL - Sliding door control passenger
2
DL - Sliding door control driver
2
DL - Driver priority unlock
2 2
DL - Door unlock
2005
2 2 2 2 2 2 1 1 1 10 09 08 2 2 2 2 2 2 1 1 1 1 1 1 2 2 2 2 2 1 1 1 1 1 2 2 2 2 1 1 2 10 09 08 1 1 1 2 2 2 1 1 1 2 2 2 2 2 2 2 2 2 10 09 08 1 1
DL - Door lock control
2006
1 2
DL - Disarm factory security
2007
1
2004
2008
2009
Chrysler 300/300c Aspen Crossfire Sebring Town & Country Dodge Avenger Caliber Challenger Charger Dakota Durango Grand Caravan Journey Magnum Nitro RAM Jeep Commander Compass Grand Cherokee Liberty Patriot Wrangler Volkswagen Routan
2010
Guide d'Application des Véhicules
DL - Arm factory security
Vehicle Compatiblity Chart
D
07 06 05 04 2 2 2 2
2 2 2 07 2 2 2
2 2 2
2
2 2
2
2
2 06 05 04 2 2
2
2 2 07 06 05 04
1 : Utilisez le Harnais-en-T inclus.
•
•
•
•
D • • D • • •
• • • • D
2 : Utilisez le Harnais-en-T vendu séparément.
* Porte coulissante en mode D2D seulement.
Légende: D: Data-to-Data (D2D) seulement. W: Wire-to-Wire (W2W) seulement. •: D2D et W2W.
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 3
CHTH1 OUTPUT INPUT
XOVER CABLE
n.c. n.c. Hood Pin
Pink Pink/Black White
n.c. n.c. n.c. n.c. n.c. n.c. n.c.
Black Red Pink Black/White Grey/Black Light Blue White
Antenna
Purple Blue
Horn
Brown
Parking Light
n.c.
Cut the loop for automatic transmission mode.
Yellow
n.c. n.c.
Purple
n.c. n.c. n.c. n.c. n.c.
Orange Blue Pink White Light Blue
Yellow/Black Purple/White Orange/Black Green Pink/Black White/Black Lt. Blue/Black
n.c. Unlock n.c. n.c. n.c. n.c. n.c.
This wire is ONLY required during the programming phase of the installation. Programming button
D2D CONN. 2
CHALL
A
Disconnect the immobilizer connector, which is located at the key cylinder.
B
Connect the male connector of the T-Harness to the immobilizer module.
C
Connect the immobilizer connector to the female connector of the T-Harness.
D
Press the CHALL programming button while inserting the T-harness into the CHALL module. The Red LED will illuminate to indicate you are in programming mode, release the programming button. Go to page 8.
D CHTH1 IGNITION BARREL
MALE
B
C FEMALE
A
IGNITION PLUG
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 4
CHTH2 (sold separately) - Vehicles 2004-2007 Vehicle with a positive starter wire. XOVER CABLE
CHALL : HARDWARE VERSION 4 FIRMWARE VERSION: 2.02 (and higher)
Fuse 7A
n.c. Pink | Rose Pink/Black | Rose/Noir Hood Pin | Pin de Capot White | Blanc (+) 12V Battery
85
87
Ground*
Black
Start (-)
12V*
Red Pink Black/White
Antenna Antenne
Ignition* Brake*
Grey/Black | Gris/Noir
Trunk*
Lock* Lt. Bleu | Bleu pâle Unlock* White | Blanc Purple | Mauve Horn | Klaxon While Running Blue | Bleu
86
87a
Parking Light Brown | Brun Lumières de Stationnement
30 Cut the loop for automatic transmission mode Coupez la boucle pour le mode de transmission automatique
87
85
86
87a 30
12V Battery
* Optional wiring connections.
CONN. 2 n.c. n.c.
Yellow | Jaune Purple | Mauve
n.c. n.c. n.c. n.c. n.c.
Orange Blue | Bleu Pink | Rose White | Blanc Lt.Blue | Bleu Pâle
Yellow/Black | Jaune/Noir Purple/White | Mauve/Blanc Orange/Black | Orange/Noir Green | Vert Pink/Black | Rose/Noir White/Black | Blanc/Noir Lt. Blue/Black | BleuPâle/Noir
n.c. n.c. n.c. n.c. n.c. MUX (+) Start IN
OUTPUT | SORTIE INPUT | ENTRÉE
Ground
Programming button Bouton de programmation
(+) Starter Back view | Vue de dos 5 PIN CONN.
Parking Light (-) Lumières de Stationnement (-)
D2D CONN. 2
MUX
PURPLE/BROWN | MAUVE/BRUN
Ignition plug
CHALL Disconnect the immobilizer connector, which is located at the key cylinder.
B
Connect the male connector of the THarness to the immobilizer module.
C
Connect the immobilizer connector to the female connector of the T-Harness.
D
Press the CHALL programming switch while inserting the T-harness into the CHALL module. The Red LED will illuminate to indicate you are in programming mode, release the programming button. Go page 6
HARDWARE V 4 FIRMWARE V 2.02 (and higher | et plus)
D CHTH2 NOT INCLUDED NON INCLUS
A
MALE MÂLE
IMM MO OBILIZ DUL ER E
A
FEMALE FEMELLE
C
B
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 5
CHTH2 (sold separately) - Vehicles 2008 and Higher Vehicle without a positive starter wire. OUTPUT INPUT
n.c. n.c. *Hood Pin
XOVER CABLE
Pink Pink/Black White
Light Blue White
n.c. n.c. n.c. n.c. n.c. n.c. n.c.
Purple Blue
n.c.
Black Red Pink Black/White Grey/Black
Antenna
Brown
Horn Parking Light
Cut the loop for automatic transmission mode. * If the vehicle does not have an OEM Hood Pin, the installer must add one.
Programming button
D2D
CONN. 2 NOT USED
CHALL
D CHTH2 NOT INCLUDED
Disconnect the immobilizer connector, which is located at the key cylinder.
B
Connect the male connector of the THarness to the immobilizer module.
C
Connect the immobilizer connector to the female connector of the T-Harness.
D
Press the CHALL programming button while inserting the T-harness into the CHALL module. The Red LED will illuminate to indicate you are in programming mode, release the programming button. Go to page 6
A
MALE
B
IMM MO OBILIZ DUL ER E
A
FEMALE
C
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 6
Updating the XSTART and RFTD Firmware Required components: XSTART. XKLOADER. § Directed Electronics D2D cable. § §
USB Port
1
USB Connector
Connect the XKLOADER to the computer. Only one XKLOADER must be used.
XKLOADER
Update the XSTART firmware:
the XSTART to the XKLOADER using the D2D cable. 2a Connect
Close all applications on your computer and open the Optimax Flash interface software.
2b Make sure no other application is using the same COM port.
Part # XKD2D65 USB Connector
XKLOADER
2c
4-PIN D2D
XSTART
The current software is listed under Unit Information. Choose the version you want to update from the Available Updates drop-down menu list.
Click on the Flash button to update XSTART.
2d A message will be displayed to confirm when the operation will be completed successfully.
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 7
Update the RFTD firmware:
3a Press and hold the Programming button on the XSTART 3b Connect the XSTART to the XKLOADER using the D2D cable.
Part # XKD2D65 USB Connector
XKLOADER
4-PIN D2D
XSTART
all applications on your computer and 3c Close open the Xpress VIP software. The current RFTD firmare is listed under Current Information in Xpress VIP.
3d Choose the firmware version by clicking on the Browse or Refresh Information. Press and hold the Programming button on the XSTART module, then click on the Flash button in Xpress VIP. Once the progress bar appears, you can release the Programming button.
3e A message will be displayed when the flash operation has been completed successfully.
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 8
Programming the CHALL Caution: The module can only be programmed a maximum of 5 times on a vehicle.
1
Check the transmission mode of the vehicle: - Automatic: cut the loop on the XSTART module. - Manual: go to step 2.
2
Press and hold the Programming button on the CHALL module.
3
See Vehicle Compatibility Chart (on page 2). T-HARNESS: Determine the T-harness required for the vehicle, 2) CHTH2 (not included) 1) CHTH1 (included) Vehicles 2004-2007, see page 4 See page 3 Vehicles 2008 and higher, see page 5
CHTCH1 OR CHTCH2
4
Connect the Unlock wire (purple/white) from the CHALL module to Ground for one second.
5
Turn the key to the "ON" position and hold until the red LED on the CHALL module starts to flash rapidly.
6a
See the CHTH1 installation on page 3 for more information. CHALL IGN CHALL
IGNITION ON
Vehicles equipped with OEM alarm: Press the unlock button on the remote car starter remote control. or Put the Purple/White wire to ground with a jumper for 1 one second.
6b
Vehicles equipped with (+) starter at Ignition: Note: Ensure that the Lt Blue/Black wire from the module is connected to the vehicles starter wire.
IGN
CHALL
Start the vehicle with the key. The LED on the CHALL module will start to flash twice as fast.
7
Turn the key to the "OFF" position and remove the key.
The Red LED will continue to flash until you press the lock button on the OEM remote.
8
If the vehicle is not equipped with the OEM remote: press and release the programming button of the CHALL module once. The LED will turn off to indicate the module has been programmed. LOCK
The module is now ready for use.
9
UNLOCK
PANIC
Continue with the remote-starter programming.
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 9
Programming a 2-Way Remote
1
Turn the Ignition on.
2
Press and hold the programming button on the module for 5 seconds, then release.
2
3
Press and release the programming button on the module once more. The parking lights will flash and the horn will honk to confirm.
3
4
Press and release the brake pedal once. The parking lights will flash once when you release the brake pedal.
5
Press and hold the LOCK button on the remote for 2 seconds.
IGN
5
OFF
6
Turn the Ignition off.
To program extra remotes, repeat steps 1 to 6 for each transmitter. (A maximum of 4 remotes can be programmed.)
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 10
Ready Mode Make sure that all doors are closed and the transmission is in the NEUTRAL position.
2
While the engine is running, engage the parking brake.
3
Make sure the brake pedal is released.
4
Push the remote START button. The parking lights will flash once and then remain on.
5
Remove the key from the ignition barrel. The vehicle will remain running with the Remote-Starter.
6
Exit the vehicle and close all doors. The Remote Starter will stop running once all the doors are closed.
&
OFF
1
IGN
START
TO DISABLE READY MODE STANDARD • Open any door(s) • Open the hood • Disengage the parking brake
WITH NEUTRAL SAFETY SWITCH • Transmission not in neutral position • Open the hood • Disengage the parking brake
Note : If the parking lights flash 3 times when Remote-Starting, Ready Mode is not enabled.
Remote Start/Alarm Diagnostics REMOTE STARTER DIAGNOSTICS Parking Lights Flashes (before starting) 3x Ready mode disabled 4x Valet mode activated (The LED is on) 5x Hood open Parking Lights Flashes (after starting) 1x Normal stop (Park B ake, Brake) 3x Runtime expired or shut down by remote 4x No tachometer signal 5x Hood open 6x Over crank threshold (8 seconds)
ALARM DIAGNOSTICS Parking Lights Flashes (after disarm) 3x 5x 6x 7x 8x 9x
Door open Hood open Trunk open Auxilliary IN Tilt Sensor Ignition
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 11
Programming the Available Features
1 2
Disarm alarm and disable valet mode, then turn the ignition on. IGN
Press and hold the XSTART Programming button for 5 seconds, then release it.
2
Press and release the XSTART Programming button 1-33 times for the desired CHANNEL (refer to pages 12 and 13 for more information).
3
Press & release 1 time Press & release 2 times Press & release 3 times Press & release 4 times Press & release 5 times
3
The parking lights will flash and the horn/siren will chirp each time the button is pressed to confirm the operation.
4
Press and release the brake pedal once.
To select a MODE:
5
NUMBER OF TIMES THE PARKING-LIGHTS WILL FLASHES
MODE 1:
press LOCK button
1X
MODE 2:
press UNLOCK button
2X
MODE 3:
press TRUNK button
3X
MODE 4:
press START button
4X
6
OFF
To reset the CHANNEL, go to step 3.
Turn the ignition off to exit the programming sequence. The parking lights will flash 4 times.
IGN
START
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 12
Feature Programming Chart #
Function
Mode 1
Mode 2
Mode 3
Mode 4
Lock button (default)
Unlock button
Trunk button
Start button
-
-
1
Add remote
Add remote
2
Configuration output
Ignition
Accessory
Starter (default)
3
Tachless crank time
Increase
4
Runtime gas/diesel
Gas 15 mins & Diesel 30 mins
Gas 7 mins & Diesel 14 mins
+++++
5
Alarm options
Disable all
Enable all
++++
Disable
Lock/Unlock
Lock only
7
Lock & unlock after remote start Ignition locks
Disable
Lock/Unlock
Lock only
8
Unlock
Single 0,25 sec
Double 0,25 sec
Single 4 secs
9
Active & passive arming
Active
Passive with Lock disabled
Passive with Lock enabled
Press Lock to activate the Alarm or the starter-kill.
When the engine is OFF and the doors are closed, the alarm w ill reactivate in 30 secs. Disable alarm option: w hen the engine is OFF the starter-kill w ill activate in 30 secs.
When the engine is OFF and all the doors are closed, the alarm w ill reactivate and lock.
10
Not supported
11
Confirmation
Silent
12
Confirmation sound
Horn
13
Confirmation time
Long
Short
14
Alarm/Starter
Alarm Off Starter On
Alarm On Starter On
15
Smart arming
Disable
Enable
-
Always chirp
16
Cold start timer
3 hours (15 mins)
1.5 hours (5 mins)
17
Dome light delay
Disable
Enable
Diesel mode
Disable
-
LED off at ignition
-
-
Alarm On Starter Off
-
Locks when the starter-kill activates
-
-
-
-
-
Enable (20)
Enable (10)
Delay betw een ignition pow er up and starter (crank).
Delay betw een ignition pow er up and starter (crank).
-
Ignores the door trigger (dome light) w hen arming on remote starting.
18
Single 2,5 secs
-
-
Lock/Unlock after shut down
LED off
Automatically LOCKS if one of the doors is not opened w ithin 30 secs.
-
-
Simultaneously changes functions 7, 9, 14 & 15.
6
+++
Gas 3 mins & Diesel 6 mins
19
Turbo mode
Disable
Enable
-
20
Tach mode
Supervision only
Tachless
21
Start attempts
2
1
3
22
Not supported
-
-
-
-
23
Master reset
Reset
-
-
-
24
Push-to-Start
Disable
-
Turn OFF engine w hen the foot-brake is pressed.
-
Enable
Start (crank) 8 secs -
Enable security
25
Auxiliary 1
Sliding doors D2D only
-
-
26
Not supported
-
-
-
27
Auxiliary 2
Sliding doors D2D only
-
-
-
28
Not supported
29
Alarm duration
30
Valet code
31
Not supported
32
Ground out
33
Ready mode activation for manual transmissions
-
-
-
30 seconds
60 seconds
120 seconds
-
Ignition ON
Ignition ON
Ignition ON
Ignition ON
Valet button x3 times.
Valet button x3 times and x1 time 3 secs.
Valet button x4 times and x1 time 3 secs.
Valet button x5 times and x1 time 3 secs.
Active 1 sec. after shut-down
Active 3 secs after shut-down
Enabled with:
Enabled with:
Hand brake (ON) and remote button (START).
Hand brake (ON) and foot brake (ON à OFF) Tach m ust be connected.
-
-
-
-
-
-
© 2010 Directed Electronics. All rights reserved.
Model: CHRSALL AS-2320TW 2-way LED Remote Start Kit
Rev.: 20101021
Page 13
Limited One-year Consumer Warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALLAPPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.920-0007 07-06
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,460 B1 *;6,243,004 B1; 6,249,216 B1; 6 , 2 7 5 , 1 4 7 B 1 ; 6 , 2 9 7 , 7 3 1 B 1 ; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6 , 8 1 2 , 8 2 9 B 1 ; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; CDN. PATENT: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2 , 4 5 4 , 0 8 9 EUROPEAN PATENT:1,053,128 PAT. PENDING: 2,291,306; MADE IN CANADA
© 2010 Directed Electronics. All rights reserved.
