2002 Mitsubishi Lancer Sedan

Transcript

2002 Mitsubishi Lancer Sedan Year: 2002 Make: Mitsubishi Model: Lancer IN-DASH APPLICATION: Dash Type: Single ISO DIN Harness: MI02 Antenna: Fuba Antenna FRONT SPEAKERS: Side Mirror: Door: 1 ¼” 6 ½” 4-Hole Pin Cushion REAR SPEAKERS: Rear Deck: 6 ½” 4-Hole Pin Cushion WIRE COLOR CODES: +12V Constant +12V Accessory Switched -12V Chassis Ground +12V Illumination +12V Dimmer LF+ LFRF+ RFLR+ LRRR+ RR- = = = = = = = = = = = = = Red/Black Blue/Yellow Chassis Green/White Black/Yellow Red/White Red/Blue Red Green White/Blue Yellow/Red Aqua Yellow/Green NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH.ABSOLUTE ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.. © 2003 SCOSCHE INDUSTRIES, INC. 1 ALL RIGHTS RESERVED FOR MORE INFORMATION VISIT www.scosche.com OR CALL SCOSCHE INDUSTRIES , INC. AT 800-363-4490 2002 Mitsubishi Lancer Sedan/Coupe PRELIMINARY: Disconnect the negative battery cable. ANTENNA: Is a Fuba Antenna located Right about rear window in center of car. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a DIN sized radio. Stereo is ISO mounted. 1. Turn AC control knobs and vent knobs to identify which cables are moving. 2. Connecting cables for AC are located under drivers side of dash on the side of center console. 3. Unclip both cables on bottom of dash. 4. Gently snap out trim radio bezel with panel removable tool. Unplug connecting harness to AC controls. 5. Unscrew (4) Philips head screws that mount radio. Disconnect and remove. FRONT DASH SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ¼” Standard mounted speaker. 1. Use panel removal tool to remove pillar panel. 2. Extract (2) Philips head screws securing tweeter, Disconnect and remove. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 6 ½” 4-Hole Standard Mounted speaker. 1. Remove power mirror cover. 2. Extract (1) Philips head screw from behind screw cover in door opener cup. 3. Extract (1) Philips head screw from behind screw cover on top front corner of door. 4. Extract (1) Philips head screw from cup and remove. 5. Extract (1) Philips head screw from behind screw cover in rear of door panel. 6. Pry door snaps loose using a panel removal tool, lift door up and away disconnect and remove. 7. Extract (4) Philips head screw securing speaker diconnect and remove. REAR DECK SPEAKER INSTALLATION: Note: The factory speaker provision is for a 6 ½” 4-Hole Standard mounted speaker. 1. Open Trunk. 2. Find rear of speaker under rear deck. 3. Remove (3) blackhead Philips screws securing top grill to rear deck. Remove grill, extract (4) Philips heads screws securing speaker, disconnect and remove. NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE ACCURA CY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.. 2 © 2003 SCOSCHE INDUSTRIES, INC. ALL RIGHTS RESERVED FOR MORE INFORMATION VISIT www.scosche.com OR CALL SCOSCHE INDUSTRIES , INC. AT 800-363-4490