Preview only show first 10 pages with watermark. For full document please download

2010 To 2014 Mustang And Shelby Gt500 Antenna

   EMBED


Share

Transcript

2010  to  2014  Mustang  and  Shelby  GT500     Antenna  Relocation  Instructions     Thank  you  for  purchasing  the  antenna  relocation  kit  /  antenna  delete  kit  from  Four   Fields  Garage.  There  are  no  permanent  changes  made  to  the  car  from  installing  this   kit.  This  Mustang  and  Shelby  GT500  "antenna  delete  kit"  removes  the  mast  antenna   on  the  rear  quarter  panel.    A  gasketed  machined  aluminum  antenna  cap  is  used  to   cover  the  antenna  hole  in  the  quarter  panel.  The  antenna  hole  cover  is  secured  in   place  by  the  gasket  and  a  bolt  on  the  underside  of  the  quarter  panel.       This  antenna  delete  kit  allows  you  to  either  repurpose  your  defroster  grid  as  the   new  AM/FM  antenna  or  install  a  separate  window  mounted  antenna  (for  example,   separately  purchase  the  Metra  44-­‐UA25  Universal  Window  Mounted  Antenna  in   addition  to  this  kit).  Installation  of  the  antenna  relocation  kit  provides  excellent  FM   and  fair  AM  reception  (receive  the  strong  AM  stations).    If  you  have  any  questions   during  the  installation,  please  call  or  email:    [email protected],  612-­‐ 802-­‐0219.     Parts  in  Kit:   1. Instructions   2. Custom  24”  antenna  cable  (from  stock  amplifier  to  defroster  connection)   3. Two  pieces  3/8”  x  2”  black  heat  shrink  tubing  (to  cover  defroster   connections)   4. M6  x  1  flange  nut   5. Custom  aluminum  antenna  cap   6. Custom  Pre-­‐cut  3M  5925  0.025”  thick  gasket  for  antenna  cap   7. Antenna  cap  mounting  stud,  Nylon  spacer,  and  5/16”  flange  nut     Tools  Needed:   1. Phillips  screw  driver   2. 10  mm  and  13  mm  wrenches   3. Snap  ring  pliers   4. Needle  nose  pliers     Instructions:   1. Remove  stock  antenna  assembly  and  install  antenna  cap   a. Remove  antenna  by  unscrewing  mast           b. Remove  antenna  nut  using  snap  ring   pliers             c. Push-­‐in  (or  snap  off)  one  tab  holding   stock  antenna  assembly  in  fender                   d. As  a  guide,  place  two  pieces  of   painters  tape  approximately  ¼”   below  and  to  the  right  of  the   antenna  mounting  hole.  Remove   adhesive  backing  on  fender  side  of  antenna  cap,  align  to  hole  in  fender   using  your  guide  and  press  in  place  for  30  seconds.  From  the  trunk   side,  install  Nylon  spacer  and  5/16”  flange  nut  to  secure  the  antenna   cap  in  place.    Be  careful  not  to  over  tighten.                           2.  Relocate  antenna  amplifier   e. Remove  trunk  liner  along  passenger  side  of  trunk  (13  mm  bolt  on   some  models)     f. Unscrew  M6x1  screw  in  antenna  assembly   (SAVE  this  screw  as  it  will  be  used  to  mount   antenna  amplifier  in  new  position)                 Copyright Four Fields Garage 2014 Page 2 3/9/14     g. Unplug  the  antenna  mast  assembly  from  the   antenna  amplifier               h. Position  antenna  amplifier  in  new  location   in  trunk  and  secure  with  M6x1  screw  and   flange  nut  provided  in  kit.    Note:    This   location  is  directly  below  back  corner  of   passenger  side  window  shelf  where  the   antenna  cable  will  be  routed.                           3.  Install  antenna  cable   i.     Route  antenna  cable  into  trunk  by  pushing   the  male  Motorola  connector  through   opening  at  back  corner  of  passenger  side   window  shelf  and  plug  antenna  cable  into   amplifier.           j. Disconnect  both  sides  of  defroster  wiring   connections  (push  in  on  center  tab  to   release  the  connector)         Copyright Four Fields Garage 2014 Page 3 3/9/14   k. Connect  the  0.25”  female   spade  connector  end  of   antenna  cable  to  the   passenger’s  side  defroster   connector.    If  desired,  use   heat  gun  or  hair  dryer  to   shrink  the  3/8”  heat   shrink  tubing  over  the   spade  connectors.    Repeat   for  driver’s  side.    Remember  to  disconnect  both  sides  of  defroster   wiring.     NOTE:  Use  the  Metra  44-­‐UA25  window  mounted  antenna  if  you  desire  to  keep  the   defroster.    This  part  is  purchased  separately  from  a  Metra  distributor.       l. Re-­‐install  trunk  liner.           Congratulations,  you’re  all  done!         Please  let  us  know  how  your  installation  went  by  posting  your  review  and  inputs  on   the  Four  Fields  Garage  Amazon  order  page.   Thank  you       LIMIT OF LIABILITY: Should this product fail to perform as designed, Four Fields Garage’s only obligation shall be to replace such quantity of the product proven to be defective; we are not liable for any incidental damages. The user shall determine the suitability of the product for their intended use and shall assume all risk and liability in connection therewith. Use of this product implies consent to these conditions. Copyright Four Fields Garage 2014 Page 4 3/9/14