Transcript
INSTALLATION INSTRUCTIONS PARTS LIST
Accessory
Application
XM RADIO SYSTEM
2013 ILX
Publications No.
BII 13548 Issue Date
MAY 2012
Aluminum tape
XM Radio Attachment Kit P/N 08B15-TX6-200 Bus cable
Accessory User’s Information Manual 2
Brackets
XM Antenna Kit (sold separately) P/N 08A15-0J1-100 Antenna 6
Washer bolts
4
Wire ties Unit Kit (sold separately) P/N 08A15-TR0-100 XM radio unit
4
Urethane tapes
2-Port Subharness Kit (sold separately) P/N 08A31-0F1-000 Cover seal
2-Port subharness
Clip
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
BII 47721 (1205)
08B15-TX6-2000-90
1 of 11
TOOLS AND SUPPLIES REQUIRED
Illustration of the XM Radio System in the Vehicle
Phillips screwdriver ANTENNA
Flat-tip screwdriver Shop towel 2-PORT SUBHARNESS
Scissors
XM RADIO UNIT
Ratchet 8 mm and 10 mm Sockets Isopropyl alcohol Tape measure Diagonal cutters Tape The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. BUS CABLE
Trim Tool Set (T/N SOJATP2014)
QA91201BK
Plastic Trim Tool (T/N SILTRIMTL10)
BUS CABLE
XM RADIO UNIT
ANTENNA
2-PORT SUBHARNESS
AUDIO UNIT Q082009AK
2 of 11
BII 47721 (1205)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
3.
Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1.
Disconnect the negative cable from the battery.
2.
Remove the passenger’s sunvisor holder by turning it 45° in the counterclockwise direction.
Remove the passenger’s sunvisor: •
Pivot the right sunvisor downward.
•
Wrap tape around the tip of flat-tip screwdriver.
•
Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push in and hold the retaining tab.
•
While holding the retaining tab, push up on the sunvisor and rotate it toward the door.
NOTE: If the retaining tab did not stay pushed in, return the sunvisor to its original position and repeat this step. FLAT-TIP SCREWDRIVER
BRACKET COVER
PASSENGER’S SUNVISOR
TAPE
TAB PASSENGER’S SUNVISOR
FRONT
PASSENGER’S SUNVISOR HOLDER (Rotate 45° in the counterclockwise direction.)
Q082007AK
Make sure the tab slides into the bracket cover.
Push the tab.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
BII 47721 (1205)
While pushing in on the tab, rotate the sunvisor toward the door.
QA92601AK
3 of 11
•
Unplug the vehicle connector, and remove the passenger’s sunvisor.
•
To prevent clips from falling into the body panel area, carefully insert a shop towel between the passenger’s A-pillar and the passenger’s A-pillar trim.
VEHICLE CONNECTOR
PASSENGER’S A-PILLAR
SHOP TOWEL
PASSENGER’S A-PILLAR TRIM FRONT
PASSENGER’S SUNVISOR QA92602AK
4.
INSTRUMENT PANEL
Remove the passenger’s A-pillar trim.
QA02102AK
•
Pull away the passenger’s door opening seal from the A-pillar trim.
•
•
Gently pull the A-pillar trim away from the A-pillar to release the three clips.
Slide the passenger’s A-pillar trim upward, and remove the passenger’s A-pillar trim.
•
Remove the shop towel and any clips.
PASSENGER’S Pull the clip. A-PILLAR
PASSENGER’S A-PILLAR
UPPER CLIP
CLIP PASSENGER’S A-PILLAR TRIM
2 CLIPS
PASSENGER’S A-PILLAR TRIM
PASSENGER’S DOOR OPENING SEAL (Pull away.) Click to Play
4 of 11
QA92604AK
QA92603AK Click to Stop
BII 47721 (1205)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
5.
Remove the remaining upper clip from the passenger’s A-pillar.
7.
Pull away the door seal from around the passenger’s dashboard side cover.
Push two tabs.
3 CLIPS
5 RETAINING TABS
PASSENGER’S A-PILLAR
UPPER CLIP (Discard.)
DOOR SEAL (Pull away.)
PASSENGER’S DASHBOARD SIDE COVER QA91202AK
QA92605AK
6.
Install the new clip (supplied) to the passenger’s A-pillar trim. NOTE: When reinstalling the A-pillar trim, refer to the service manual for the correct overlap procedure.
8.
Remove the passenger’s dashboard side cover (three clips and five retaining tabs).
9.
Open the glove box. Remove the passenger’s dashboard trim (six clips).
6 CLIPS
NEW CLIP (supplied)
PASSENGER’S DASHBOARD TRIM
PASSENGER’S A-PILLAR TRIM
Q0N0533AH
GLOVE BOX
Click to Play
QA00603BH Click to Stop
10. Close the glove box.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
BII 47721 (1205)
5 of 11
11. Remove the passenger’s dashboard undercover. •
Release three clips and two pins, then pull the passenger’s dashboard undercover toward you.
•
Remove the bulb socket, and remove the passenger’s dashboard under cover.
13. Remove the driver’s inner dashboard trim (four clips and unplug the vehicle connector).
BULB SOCKET
VEHICLE CONNECTOR
3 CLIPS
4 CLIPS
DRIVER’S INNER DASHBOARD TRIM Click to Stop QA00602AH
Click to Play
2 PINS
PASSENGER’S DASHBOARD UNDERCOVER
14. Move the shift lever to the N (neutral) position. Apply masking tape to the areas shown. QA92703BH
12. Remove the driver’s dashboard lower cover (nine clips, and unplug the vehicle connector).
TAPE
VEHICLE CONNECTOR TAPE
SHIFT LEVER QAN2301AH
9 CLIPS
Click to Play
6 of 11
DRIVER’S DASHBOARD LOWER COVER
QA91808BH
Click to Stop
BII 47721 (1205)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
15. Remove the heater control panel (one self-tapping screw, three clips, and three retaining tabs).
17. Remove the glove box (three self-tapping screws and unplug the vehicle connectors).
VEHICLE CONNECTORS SELF-TAPPING SCREW
HEATER CONTROL PANEL
3 CLIPS 3 RETAINING TABS
3 SELF-TAPPING SCREWS GLOVE BOX
QA00604BH
QA91802CK Click to Stop
Click to Play
16. Remove the two bolts from the bottom of the glove box.
18. Remove the two bolts, then remove the center panel (eight clips and unplug the vehicle connectors). 8 CLIPS
GLOVE BOX
VEHICLE CONNECTORS
2 BOLTS QA00606AH
CENTER PANEL Click to Play
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
BII 47721 (1205)
2 BOLTS
QA00605CH
Click to Stop
7 of 11
19. Install the two brackets to the audio unit with two washer bolts. Do not tighten the washer bolts at this time.
22. Using scissors, cut one urethane tape in half.
2 URETHANE TAPES
AUDIO UNIT 2 WASHER BOLTS (Do not tighten.) 2-PORT SUBHARNESS
Align. Align.
URETHANE TAPE (Cut in half.)
2 BRACKETS
QA91204AK
QA02101AK
23. Wrap the cut pieces of urethane tape around the 2-port subharness connectors as shown. 24. Plug the bus cable connector into the XM radio unit.
20. Install the XM radio unit onto the brackets on the audio unit with four washer bolts.
AUDIO UNIT
BUS CABLE
2 BRACKETS XM RADIO UNIT
4 WASHER BOLTS
XM RADIO UNIT
QA91402AK QA91401BK
21. Tighten the two washer bolts installed in step 19.
8 of 11
BII 47721 (1205)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
25. Plug the 2-port subharness into the audio unit connector and into the bus cable connector.
28. On the passenger’s side of the vehicle, use isopropyl alcohol on a shop towel to clean the top inside corner of the windshield at the location shown. INSIDE
AUDIO UNIT
Align. 2-PORT SUBHARNESS
50 mm (2.0 in.) ANTENNA BUS CABLE
Clean here.
QA92606AK
26. Using scissors, cut three urethane tapes in half.
WINDSHIELD
680 mm (26.8 in.) 50 mm (2.0 in.)
4 ADHESIVE BACKINGS
50 mm (2.0 in.)
PASSENGER’S A-PILLAR ANTENNA
ANTENNA
29. Remove the four adhesive backings from the antenna, and attach the antenna to the windshield at the measurement shown. Apply firm pressure to the antenna for at least 30 seconds.
ANTENNA CABLE
3 URETHANE TAPES (Cut in half.)
QA91404BK
QA91403AK
27. Wrap five of the cut pieces of urethane tape around the antenna cable at the measurements shown.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
BII 47721 (1205)
9 of 11
30. Using isopropyl alcohol on a shop towel, clean the outside of the windshield over the antenna area.
34. Route the antenna cable down behind the dashboard.
Align.
GLOVE BOX OPENING
OUTSIDE
COVER SEAL
ANTENNA CABLE Clean here. QA92607AK
31. Remove the adhesive backing from the cover seal, position it over the antenna, and attach it to the outside of the windshield.
QA91701AK
35. Using one wire tie, secure the antenna cable to the vehicle harness.
32. Using scissors, cut the aluminum tape into four pieces.
VEHICLE HARNESS
ALUMINUM TAPE (Cut in 4 pieces.)
GLOVE BOX OPENING
PASSENGER’S A- PILLAR ANTENNA CABLE
ANTENNA CABLE
WIRE TIE
QA92701AK
QA91405AK
33. Route the antenna cable along the passenger’s A- pillar. Using isopropyl alcohol on shop towel, clean the A-pillar where the aluminum tape will attach. Using three pieces of aluminum tape, secure the antenna cable to the A-pillar in the areas shown. NOTE: Be careful not to attach the aluminum tape over the holes in the A-pillar.
10 of 11
BII 47721 (1205)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
36. Route the antenna cable through the glove box opening and toward the center panel.
39. Inside the glove box opening, bundle the excess antenna cable, and secure it to the vehicle harness with two wire ties.
CENTER PANEL OPENING
VEHICLE HARNESS 30 mm (1.2 in.) ANTENNA CABLE GLOVE BOX OPENING 2 WIRE TIES
QA91702AK
ANTENNA CABLE
37. Route the antenna cable out the center panel opening, and align it with the other vehicle connector.
QA92702AK
40. Plug the 2-port subharness connector to the vehicle connector. 41. Plug the antenna cable connector to the XM radio unit.
VEHICLE HARNESS
42. Plug the vehicle connectors to the audio unit, and reinstall the center panel.
CENTER PANEL OPENING
43. Check that all wire harnesses are routed properly and all connectors are plugged in. 44. Check the overlap between the headliner and the passenger’s A-pillar trim. Refer to the service manual. If necessary, adjust the overlap. 45. Reinstall all removed parts. 46. Connect the negative cable to the battery and check the operation of all lights and electrical accessories.
WIRE TIE
47. Press and hold the radio power button for two seconds to restore radio and navi (if equipped) system functions.
Align. ANTENNA CABLE
VEHICLE CONNECTOR
48. Reset the clock on vehicles without navigation.
QA91801AK
38. Using one wire tie, secure the antenna cable to the vehicle harness inside the center panel.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
49. Check the operation of the XM radio system according to the Accessory User’s Information Manual. 50. If the IMA battery level gauge is at zero, start the engine and hold the rpm between 3500 and 4000 (no load) in P or N position until the Charge/Assist meter indicates the IMA system has stopped charging the battery.
BII 47721 (1205)
11 of 11
