Transcript
EarthWay Flex-Select ®
®
HWAY WARRANT ART
HWAY WARRANT ART
How to Install a Tray
First ensure the hopper is clean and there is no debris trapped around the tray mounting area. Secondly install the Pivot Rod Clip into the Shut-off of the selected Tray. Next, insert the Pivot Rod into the Clip. TIP: The Clip may have a burr in the hole, use a Phillips screwdriver to remove the burr. See to make installing the Pivot Rod easier. Pliers may be required to help squeeze the Pivot Rodinto the Clip. When the Rod is secure inside the Clip push the free end of the Clip over the Pivot Rod to firmly secure the rod to the clip. Next, install the Tray from the top downwards into the hopper (see figure) positioning the center hole of the tray over the Pinion Shaft from the gear box with the Pivot Rod through the bottom of the hopper and facing toward the spreader’s handlebar. For ease of locating into position the shut-off of the chosen tray is best in the open position, with the exception of the red STANDARD-OUTPUT Tray where the two adjustable throwing ports are best in the closed position. NOTE: The gearbox can be moved along the axle to ease aligning of the tray hole and the pinion shaft. Once the tray is in place check that the tray is sealed and flush against the hopper sides. To check if the tray is properly located, push the tray edges downwards. Install the two quarter turn fasteners (see figure) through the two exposed tray holes and push down and twist a quarter turn to secure. Lastly, connect the free end of the Pivot Rod into the Pivot linkage at the bottom of the Control Rod. Position the Clip into the free hole and push the Pivot Rod into the clip. TIP: The Clip may have a burr in the hole, use a Phillips screwdriver to remove the 5 burr (see figure) When the Pivot Rod is positioned inside the Clip push the free end of the Clip over the Pivot Rod to firmly secure the rod and the clip together.
How to ensure your spreader is properly calibrated HIGH-OUTPUT and LOW-OUTPUT Trays: Make sure the drop holes in the bottom of the hopper are FULLY CLOSED when the Rate Control Lever is resting on the Stop #0. If the shut-off is not set correctly, please adjust Control Rod at the Pivot to position the shut-off for FULLY CLOSED at position at the Stop #0 on the Rate Control Lever. As a side note, the HIGH-OUTPUT and LOW-OUTPUT Trays do not include or use a horizontal agitator.
E
Y
Y
E
Tray Setup and Calibration Techniques
HIGH-OUTPUT F13130HKIT Blue Tray install Pivot Rod from the bottom to the top
4
2
3
1
Deburr Rod Clip
Shut-Off End
LOW-OUTPUT F13130LKIT Black Tray install Pivot Rod from the top to the bottom
2 3 Shut-Off End 1
30
STANDARD-OUTPUT PRO F13130DKIT
0
Red Tray install Pivot Rod from the bottom to the top
2
1
Shut-Off End
3
PIVOT CALIBRATION POINT
Quarter Turn Tray Fastener
Calibration Adjustment 6 Review the Control Lever position to confirm that it is set so that the forward edge of the Lever is resting at #0 (the stop) and the drop holes are closed. Move the spreader back & forth to ensure that the cam is positioned to allow the Oscillating Shut-off to close fully. If the shut-off is not properly positioned, you will need to adjust the Control Rod at the Pivot Bracket shown below. TIP: If your shut-off is not able to CLOSE fully, loosen the top nut a few turns, then tighten the lower nut so that it allows you to push the shut-off fully closed. Next, tighten each nut so that they contact the pivot bracket without moving it, and then carefully tighten each nut fully so they do not loosen during use. Recheck adjustment as outlined above. continued 12-2014 ~ F52157SC ©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, FLEX-SELECT ®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc. Use of trademarks are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507
GAU LE
How to ensure your spreader is properly calibrated
- continued
STANDARD-OUTPUT Tray: Make sure the drop holes in the bottom of the hopper are FULLY OPEN when the Rate Control handle is on #30. If the shut-off is not set correctly, please adjust Control Rod at the Pivot to position the shut-off for FULLY OPEN hopper position at #30 on the Rate Control Lever. Install the horizontal agitator through the pinion shaft in the hopper bottom. Finally, install the debris screen onto the Quarter-turn fasteners and push down to snap and secure. Calibration Adjustment Review the Control Lever position to confirm that it is set so that the rear edge of the Lever is resting at #30 (the stop) and the drop holes are open. If the shut-off is not properly positioned, you will need to adjust the Control Rod at the Pivot Bracket shown below. TIP: If your shut-off is not able to OPEN fully, loosen the bottom nut a few turns, then tighten the upper nut so that it allows you to push the shut-off fully open. Next, tighten each nut so that they contact the pivot bracket without moving it, and then carefully tighten each nut fully so they do not loosen during use. Recheck adjustment as outlined above.
#30
#0
30 0
GAUGE & LEVER
PIVOT CALIBRATION POINT
Control Lever Drag adjustment If the Control Lever does not stay in position causing the setting rate to change without your intervention, you can adjust the drag on the Lever by tightening or loosening the nut shown to the right until the drag is appropriate.
Lever Drag Adjustment
If you have any questions regarding the assembly or safe operation your spreader, please contact us at 800-294-0671 or 574-848-7491 Monday - Friday 9:00am - 4:00pm Eastern, or email us at
[email protected]. If you are outside of the USA, please visit our web site www.earthway.com for guidance on a dealer local to you who can assist with your enquiry.
FLEX-SELECT BROADCAST SPREADER SETTING MATRIX ®
GRANULAR MATERIAL STANDARD-OUTPUT Red Tray
PARTICLE SIZES: LBS. PER 1,000 SQUARE FEET
Fine/Small (1/16" SAND) SETTING
SPREAD WIDTH FT
SPREAD METERS
7 10 13 14 16 18 20 22 24 26
18' 18' 18' 18' 18' 18' 18' 18' 18' 18'
LBS. PER 1,000 SQUARE FEET
FINE SETTING
2 LBS. 3 LBS. 4 LBS. 5 LBS.
14 16 18 20
1 LB. 2 LBS. 3 LBS. 4 LBS. 5 LBS. 6 LBS. 7 LBS. 8 LBS. 9 LBS. 10 LBS.
Medium (3/32") SETTING
SPREAD WIDTH FT
SPREAD METERS
5.5m 5.5m 5.5m 5.5m 5.5m 5.5m 5.5m 5.5m 5.5m 5.5m
9 13 16 20 22 25 27 28 30 22 = 2 pass
24' 24' 24' 24' 24' 24' 24' 24' 24' 24'
7.3m 7.3m 7.3m 7.3m 7.3m 7.3m 7.3m 7.3m 7.3m 7.3m
SPREAD WIDTH FT
SPREAD METERS
COARSE SETTING
SPREAD WIDTH FT
SPREAD METERS
8' 8' 8' 8'
2.4m 2.4m 2.4m 2.4m
22 25 28 30
14' 14' 14' 14'
4.3m 4.3m 4.3m 4.3m
SETTING
SPREAD WIDTH FT
SPREAD METERS
GRASS SEED
Large (1/8") ICE MELT SETTING
SPREAD WIDTH FT
SPREAD METERS
14 18 23 27 30 23 = 2 pass 25 = 2 pass 27 = 2 pass 28 = 2 pass 30 = 2 pass
36' 36' 36' 36' 36' 36' 36' 36' 36' 36'
11m 11m 11m 11m 11m 11m 11m 11m 11m 11m
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the drop holes in the Standard-Output Tray are fully open when the Rate Control handle is on #30. If not, please adjust control rod at the pivot to allow for a full open hopper holes with the handle at position at #30.
GRANULAR MATERIAL LOW-OUTPUT Black Tray PARTICLE SIZES: LBS. PER 1,000 SQUARE FEET
Fine/Small (1/16" SAND)
Medium (3/32")
SETTING
SPREAD WIDTH FT
SPREAD METERS
8 10 12 13 16 18 20 21 23 24
16' 16' 16' 16' 16' 16' 16' 16' 16' 16'
4.9m 4.9m 4.9m 4.9m 4.9m 4.9m 4.9m 4.9m 4.9m 4.9m
10 13 18 20 22 25 27 29 30 22 = 2 pass
20' 20' 20' 20' 20' 20' 20' 20' 20' 20'
6.1m 6.1m 6.1m 6.1m 6.1m 6.1m 6.1m 6.1m 6.1m 6.1m
LBS. PER 1,000 SQUARE FEET.
FINE SETTING
SPREAD WIDTH FT
SPREAD METERS
COARSE SETTING
SPREAD WIDTH FT
SPREAD METERS
2 LBS. 3 LBS. 4 LBS. 5 LBS.
15 18 21 24
9' 9' 9' 9'
2.7m 2.7m 2.7m 2.7m
21 24 27 30
15' 15' 15' 15'
4.6m 4.6m 4.6m 4.6m
1 LB. 2 LBS. 3 LBS. 4 LBS. 5 LBS. 6 LBS. 7 LBS. 8 LBS. 9 LBS. 10 LBS.
GRASS SEED
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the drop holes in the LOW-OUTPUT TRAY are fully closed when the Rate Control Handle is resting on the stop #0. If not, please adjust control rod at the pivot to ensure the shut-off is fully closed with the handle at position at #0. Move the spreader slightly to confirm the calibration because of the cam.
GRANULAR MATERIAL HIGH-OUTPUT Lt. Blue 2-hole Tray Large PARTICLE SIZES: (1/8") ICE MELT LBS. PER 1,000 SQUARE FEET.
SETTING
SPREAD WIDTH FT
SPREAD METERS
1 LB. 2 LBS. 3 LBS. 4 LBS. 5 LBS. 6 LBS. 7 LBS. 8 LBS. 9 LBS. 10 LBS.
7 10 12 14 15 17 20 21 23 24
28' 28' 28' 28' 28' 28' 28' 28' 28' 28'
8.5m 8.5m 8.5m 8.5m 8.5m 8.5m 8.5m 8.5m 8.5m 8.5m
EXTRA LARGE ROCK SALT SETTING
SPREAD WIDTH FT
SPREAD METERS
8 11 13 14 15 16 17 18 19 21
26' 26' 26' 26' 26' 26' 26' 26' 26' 26'
7.9m 7.9m 7.9m 7.9m 7.9m 7.9m 7.9m 7.9m 7.9m 7.9m
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the drop holes in the HIGH-OUTPUT TRAY are fully closed when the Rate Control Handle is resting on the stop #0. If not, please adjust control rod at the pivot to ensure the shut-off is fully closed with the handle at position at #0. Move the spreader slightly to confirm the calibration because of the cam.
©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc. Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507
FLEX-SELECT BROADCAST SPREADER SETTING MATRIX ®
GRANULAR MATERIAL STANDARD-OUTPUT Red Tray
PARTICLE SIZES: Grams PER Square Metre
5 10 15 20 24 29 34 39 44 49
Fine/Small (1.5MM) SETTING
SPREAD WIDTH FT
SPREAD METRES
7 10 13 14 16 18 20 22 24 26
18 18 18 18 18 18 18 18 18 18
FINE SETTING
14 16 18 20
Medium (2.0MM)
Large (3.0MM) ICE MELT
SETTING
SPREAD WIDTH FT
SPREAD METRES
SETTING
SPREAD WIDTH FT
SPREAD METRES
5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5
9 13 16 20 22 25 27 28 30 22 x 2 pass
24 24 24 24 24 24 24 24 24 24
7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3
14 18 23 27 30 23 x 2 pass 25 x 2 pass 27 x 2 pass 28 x 2 pass 30 x 2 pass
36 36 36 36 36 36 36 36 36 36
11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0
SPREAD WIDTH FT
SPREAD METRES
COARSE SETTING
SPREAD WIDTH FT
SPREAD METRES
8 8 8 8
2.4 2.4 2.4 2.4
22 25 28 30
14 14 14 14
4.3 4.3 4.3 4.3
SETTING
SPREAD WIDTH FT
SPREAD METRES
10 13 18 20 22 25 27 29 30 22 x 2 pass
20 20 20 20 20 20 20 20 20 20
6.1 6.1 6.1 6.1 6.1 6.1 6.1 6.1 6.1 6.1
GRASS SEED Grams PER Square Metre
10 15 20 25
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the drop holes in the STANDARD-OUTPUT Tray are fully open when the Rate Control handle is on #30. If not, please adjust control rod at the pivot to allow for a full open hopper holes with the handle at position at #30.
GRANULAR MATERIAL LOW-OUTPUT Black Tray PARTICLE SIZES: Grams PER Square Metre
5 10 15 20 24 29 34 39 44 49
Fine/Small (1.5MM) SETTING
SPREAD WIDTH FT
SPREAD METRES
8 10 12 13 16 18 20 21 23 24
16 16 16 16 16 16 16 16 16 16
4.9 4.9 4.9 4.9 4.9 4.9 4.9 4.9 4.9 4.9
Medium (2.0MM)
GRASS SEED Grams PER Square Metre
10 15 20 25
FINE SETTING
SPREAD WIDTH FT
SPREAD METRES
COARSE SETTING
SPREAD WIDTH FT
SPREAD METRES
15 18 21 24
9 9 9 9
2.7 2.7 2.7 2.7
21 24 27 30
15 15 15 15
4.6 4.6 4.6 4.6
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the drop holes in the LOW-OUTPUT TRAY are fully closed when the Rate Control Handle is resting on the stop #0. If not, please adjust control rod at the pivot to ensure the shut-off is fully closed with the handle at position at #0. Move the spreader slightly to confirm the calibration because of the cam.
GRANULAR MATERIAL HIGH-OUTPUT Lt. Blue 2-hole Tray Large PARTICLE SIZES: (3.0MM) ICE MELT Grams PER Square Metre
5 10 15 20 24 29 34 39 44 49
SETTING
SPREAD WIDTH FT
SPREAD METRES
7 10 12 14 15 17 20 21 23 24
28 28 28 28 28 28 28 28 28 28
8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5
EXTRA LARGE ROCK SALT SETTING
SPREAD WIDTH FT
SPREAD METRES
8 11 13 14 15 16 17 18 19 21
26 26 26 26 26 26 26 26 26 26
7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9
Calibration: Start by ensuring that your spreader calibration is correct. Make sure the 2 drop holes in the HIGH-OUTPUT TRAY are fully closed when the Rate Control Handle is resting on the stop #0. If not, please adjust control rod at the pivot to ensure the shut-off is fully closed with the handle at position at #0. Move the spreader slightly to confirm the calibration because of the
©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc. Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507
HWAY WARRANT ART
E
E
Y
31127 ROD CLIP
F12135 1/4 TURN FASTENER
F12135 1/4 TURN FASTENER
LOW-OUTPUT F13130LKIT
12209 HOPPER BUSHING
F14102 SHUT OFF PLATE RETAINER RING
F12219H HIGH-OUTPUT SHUTOFF ASSY
F14102 SHUT OFF PLATE RETAINER RING
36107 1/8 X 1 FLAT HD F12117 CAM 18-8 SS RIVET These parts are wear items and designed to be consumed with normal operation and have a 90 day warranty
F12135 1/4 TURN FASTENER
12209 HOPPER BUSHING
31138 #8 X 3/8 PMT #8HD (BLACK)
F12219D DUAL-PORT PRO SHUT-OFF ASSY
12209 HOPPER BUSHING
31135 #8 X 1/2 PHPS (BLACK)
33117 AGITATOR
HIGH-OUTPUT F13130HKIT
F44251 PIVOT ROD STANDARD-OUTPUT
F44251H PIVOT ROD HIGH-OUTPUT
F12111 AGITATOR PIN RETAINER
F12135 1/4 TURN FASTENER
STANDARD-OUTPUT PRO F13130DKIT
31127 ROD CLIP
31127 ROD CLIP
36208 #6 X 3/8" TYPE 25 PHPS S.S.
F12219 STANDARD-OUTPUT SHUT-OFF ASSY
12209 HOPPER BUSHING
31135 #8 X 1/2 PHPS (BLACK)
31138 #8 X 3/8 PMT #8HD (BLACK)
33117 AGITATOR
36107 1/8 X 1 FLAT HD F12117 CAM 18-8 SS RIVET These parts are wear items and designed to be consumed with normal operation and have a 90 day warranty
F12111 AGITATOR PIN RETAINER
36208 #6 X 3/8" TYPE 25 PHPS S.S.
F12219L LOW-OUTPUT SHUTOFF ASSY
F44251L PIVOT ROD LOW-OUTPUT
F40003 DEBRIS SCREEN Included with both Standard Output Trays only
STANDARD-OUTPUT F13130KIT
F44251 PIVOT ROD STANDARD-OUTPUT
31127 ROD CLIP
HWAY WARRANT ART
Y
