2014 Tundra Vehicle Remote Start System

Transcript

Doc. 15.181.00 TOYOTA PIO / DIO Tundra 12/05/13 2014 Vehicle Remote Start System Part Number: 00016-34043 Accessory Code: QR10 Vehicle Service Parts TMS Remote Start Kit Contents Item # Qty Description 1 1 Remote Start Module w/ DNA Software 2 1 Main Wiring Harness 3 1 2-Way IVU Antenna 4 1 2-Way IVU Antenna Harness 5 1 Immobilizer Interface Module 6 1 Owner’s Manual 7 1 Hardware Bag 8 1 2-Way Transmitter 9 4 Large Cable Ties 10 1 Hood Pin Switch Kit 11 1 Key Tag (May be required for reassembly) Part Number Qty 00016-34035-01 1 2-Way Antenna Harness Description 00016-34035-02 1 Main Wiring Harness 00016-34035-03 1 Hardware Bag 00016-34035-04 1 2-Way Antenna 00016-34035-05 1 Immobilizer Interface Module 00016-34035-06 1 2-Way Transmitter 00016-34035-07 1 Removable Software Card 00016-34035-08 1 Main Module 00016-08032-09 1 Hood Pin Switch Bracket 00016-08032-10 1 Hood Pin Switch 00016-34035-11 2 Red Scotch-Lok Connector 00016-34035-12 6 8” Wire Ties 00016-34035-14 1 Dielectric Grease 00016-08032-11 1 Hood Pin Switch Harness 00016-34035-16 1 Key Tag Hardware Bag Contents Item # Qty Reqd. Description 1 15 8” Black Cable Ties 2 1 Foam Pad 3 1 Underhood Label 4 10 Black T-Taps 5 1 Red T-Tap 6 1 Blue T-Tap 7 General Applicability Legend STOP 8 STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. Safety Tools CRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation. Special Tools TOOLS AND EQUIPMENT: This calls out the specific tools and equipment required for this process. Recommended Tools ! REVISION MARK: This mark highlights a change in installation with respect to a previous issue. Installation Tools Phillips Screwdriver Straight-Slot Screwdriver Ratchet w/ Extension 10 mm Socket Diagonal Wire Cutters Common Pliers Flashlight Nylon Trim Tool Torque Wrench (48 in. lbs.) Special Chemicals VPC Approved Cleaner S SAFETY TORQUE: This mark indicates that torque is related to safety. SPECIAL NOTE: After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality. Rev. - 12/3/13 2014 Tundra INSTALLATION PREPARATION Vehicle Remote Start System Negative Battery Cable Before starting installation: 1. Familiarize yourself with the installation instructions. 2. Inspect the kit components (Refer to Kit Contents and Hardware Bag Contents). VEHICLE PREPARATION 1. Place protective coverings on vehicle. ! 2. “IMPORTANT......IMPORTANT” Disconnect Negative Battery Cable. Regular Cab 3. Remove the driver’s side front door step sill panel. Regular Cab: Disengage the (6) claws and (3) clips. Double Cab: Disengage the (6) claws and (3) clips. Double Cab 4. Remove the driver’s front kick panel, by removing the (1) plastic retaining nut and disengaging the (1) retaining clip and (1) claw. Plastic Nut Retaining Clip Claw Page 2 of 23 2014 VEHICLE PREPARATION; continued Tundra 5. Remove the lower steering column cover by removing the (2) phillips screws disengaging the (2) claws. 6. Remove the driver’s instrument side panel by disengaging the (7) claws. 7. Loosen the lower instrument panel subassembly by removing the (2) 10 mm bolts and disengaging the (9) clips and (1) claw. 8. Remove the hood release lever and disengage any connectors that may be attached to the finish panel. Remove finish panel from the vehicle. Page 3 of 23 Vehicle Remote Start System 2014 Tundra Vehicle Remote Start System VEHICLE PREPARATION; continued 9. Remove the driver’s side knee air bag assembly by removing the (4) 10 mm bolts and disconnecting the connector. 10. Apply protective tape to the driver’s “A” pillar, as shown. Detach the claw and open the cover. Remove the driver’s side “A” pillar trim panel by removing the (1) 10 mm bolt and disengaging the (1) claw. Protective Tape 11. Remove the passenger’s side front door step sill panel. Regular Cab: Disengage the (6) claws and (3) clips. Double Cab: Disengage the (6) claws and (3) clips. Regular Cab Double Cab Page 4 of 23 2014 Tundra Vehicle Remote Start System VEHICLE PREPARATION; continued 12.Remove the passenger’s front kick panel, by removing the (1) plastic retaining nut and disengaging the (1) retaining clip and (1) claw. Retaining Clip Claw INSTALLATION PROCEDURES 1. Clean the area of the windshield, to the right of the rear view mirror with a approved VPC cleaning solution. Ensure the glass surface is completely dry. 2. Connect the antenna harness to the antenna. Remove the protective backing and mount the antenna to the windshield, to the right of the rear view mirror. Press firmly to ensure a good glass to adhesive bond. Cable Ties 4. Route the antenna cable in between the body structure and headliner, toward the driver’s “A” pillar. 5. Route the antenna cable down the driver’s “A” pillar to the underdash area. Secure the antenna cable to the existing factory harness with (3) cable ties. Page 5 of 23 2014 Tundra INSTALLATION PROCEDURES 6. Route the Violet, Violet/White, Green, Pink and Yellow wires to the passenger’s side of the vehicle. 7. Secure the remote start harness along it’s routing path with cable ties, as needed. 8. Careful follow the wiring diagram and factory connector details found on the following (6) pages. Page 6 of 23 Vehicle Remote Start System 2014 Tundra Vehicle Remote Start System WIRING DIAGRAM Disconnect the factory female ignition switch connector and plug the corresponding remote start harness female connector into the ignition switch. Connect the factory female ignition switch connector into the corresponding remote start harness male connector. GRAY / BLACK WIRE [Key-In-Sense Input]: Use black T-Tap and connect to the GRAY WIRE in connector J18, location 1. BEIGE WIRE [Horn Output]: Use black T-Tap and connect to the BEIGE WIRE in connector J45, location 8. PINK WIRE [ Unlock Output]: Use black T-Tap and connect to the WHITE WIRE in connector MJ2, location 16. ORANGE WIRE [Parking Light Output]: Use black T-Tap and connect to the BEIGE WIRE in connector J10, location 18. YELLOW WIRE [ Lock Output ]: Use black T-Tap and connect to the RED WIRE in connector MJ2, location 17. VIOLET WIRE [IMI BCM Side]: The YELLOW portion of the IMI wire in the junction connector AJ5 (location 1) must be de-pinned, see “Detail A” on the next page. BROWN/WHITE WIRE [Brake Input]: Use blue T-Tap and connect to the BEIGE WIRE in connector A4, location 1. WHITE WIRE [ Tachometer Input]: Use black T-Tap and connect to the BROWN WIRE in connector J17, location 9. GREEN WIRE [IMO]: Use black T-Tap and connect to the PINK WIRE in connector AJ5, location 2. VIOLET / WHITE WIRE [IMI Vehicle Side]: Use black T-Tap and connect to the BLACK WIRE in connector AJ5, location 1. See “Detail A” on the next page for additional details. Immobilizer Interface Module L.E.D. Programming Button GRAY WIRE [ Door Ajar Input ]: Use black T-Tap and connect to the GRAY WIRE in connector J4, location 24. YELLOW/BLACK WIRE [ Hood Input ]: Use red T-Tap and connect to the BLUE WIRE in connector AJ10, location 19. If vehicle is NOT equipped with factory security, a hood pin switch must be installed, see Page 14 for additional details. BLACK WIRE- (16 GA.) GROUND: Connect to the factory 10 mm ground location in the driver’s kick panel area. Antenna Page 7 of 23 2014 Tundra Vehicle Remote Start System INSTALLATION PROCEDURES; continued T-TAP INSTALLATION When installing female T-Tap connectors, be sure the wire is located inside the wire channel of the female T-Tap connector before closing the connector over the wire with pliers. Step A Step B Step C IMPORTANT! After installation, inspect and ensure that the module harnesses are clear of HOT, SHARP or MOVING objects. IMPORTANT! Care MUST be exercised when using the BLACK T-Taps. To avoid damage and broken wires, please note: • Ensure there is NO tension on the T-Tap connection when securing the harness. The wire should be slack. • Excessive manipulation and/or stress on the wire connection could lead to wire breakage. • Center the wire in the metal insert, NOT the plastic side of the T-Tap. Misalignment of the wire against the metal insert could lead to cutting the wire. • It is recommended to close close the T-Tap with your fingers (Step A above). After the T-Tap has been closed with your fingers, applying light pressure with a set of pliers will complete the conSTOP nection. • When possible, install T-Taps 1” away from connector. DETAIL A 1 1. Separate the two halves of the junction connector. 2 2. Carefully lift up the secondary lock and remove the YELLOW IMI wire. 3. Fold over the terminal end of the wire. 4. Protect the terminal end, by wrapping the wire and terminal end with electrical tape. Ensure that the terminal end is completely covered. 3 4 5. Install T-Tap. 5 AJ5 Page 8 of 23 Note: The Yellow IMI wire may be a different color in each side of the junction connector. CONNECTOR DETAILS - 2014 Tundra Vehicle Remote Start System 1. CONNECTOR J9: 12+ VDC 1 & 2 / Ignition 1 & 2 / Accessory / Starter Location : At Ignition Switch. Disconnect the factory female ignition switch connector and plug the corresponding remote start harness female connector into the ignition switch. Connect the factory female ignition switch connector into the corresponding remote start harness male connector. 2. CONNECTOR J10: Parking Lights / Head Lights Location : At Head Light Dimmer Switch. Location 18 Beige Parking Lights REMOTE START Orange J10 CAR Beige 3. CONNECTOR J45: Horn Location : At Spiral Cable Assembly. Location 8 Beige Horn J45 REMOTE START Beige CAR Beige T-TAP COLOR Black Page 9 of 23 T-TAP COLOR Black CONNECTOR DETAILS - 2014 Tundra Vehicle Remote Start System 4. CONNECTOR J18: Key-In-Sense Location : At Ignition Switch. J18 Location 1 Gray Key-In-Sense REMOTE START Gray/Black CAR Gray T-TAP COLOR Black 5. CONNECTOR J17: Tachometer Location : At DLC3. Location 9 Brown Tachometer J17 REMOTE START White CAR Brown T-TAP COLOR Black 6. CONNECTOR A4: Brake Location : At Brake Pedal Assembly. Location 1 Beige Brake REMOTE START Brown CAR Beige T-TAP COLOR Blue A4 Page 10 of 23 CONNECTOR DETAILS - 2014 Tundra Vehicle Remote Start System 7. CONNECTOR J4: Door Ajar Location : At body ECU, driver’s JB. Location 24 Gray Door Ajar J4 REMOTE START Gray CAR Gray T-TAP COLOR Black 8. CONNECTOR MJ2: Unlock / Lock Location : Passenger’s kick panel. Location 16 White Unlock Location 17 Red Lock REMOTE START Pink Yellow CAR White Red MJ2 9. CONNECTOR AJ10: Hood Location : At driver’s kick panel area. If vehicle is NOT equipped with factory security, a hood pin switch must be installed, see Page 14 for additional details. Location 19 Blue Wire Hood REMOTE START Yellow/Black CAR Blue T-TAP COLOR Red AJ10 Page 11 of 23 T-TAP COLOR Black Black CONNECTOR DETAILS - 2014 Tundra Vehicle Remote Start System 10. CONNECTOR AJ5: IMI / IMO Location : Passenger’s Kick Panel Area. Location 1 Black Wire IMI REMOTE START Violet Violet/White Green Location 2 Pink Wire IMO CAR Yellow Black Pink Location 1 Yellow Wire IMI T-TAP COLOR Black Black Black 1 1. Separate the two halves of the junction connector. 2 2. Carefully lift up the secondary lock and remove the YELLOW IMI wire. 3. Fold over the terminal end of the wire. 4. Protect the terminal end, by wrapping the wire and terminal end with electrical tape. Ensure that the terminal end is completely covered. 3 5. Install T-Tap. 4 5 AJ5 Page 12 of 23 Note: The Yellow IMI wire may be a different color in each side of the junction connector. 2014 Tundra INSTALLATION PROCEDURES; continued 9. Locate the factory ground lug in the driver’s kick panel area. Secure the remote start harness ground wire to the 10 mm ground lug located in the driver’s kick panel area. 10.Plug the remote start wire harness into the remote start module. 11. Plug the remote start antenna into the rear of the remote start module. 10-Pin Antenna 24-Pin 12.Secure the remote start module to the factory harness connected to the driver’s JB and the metal dash assembly with (2) cable ties. 13.Secure the remote start harness to the existing vehicle harness with cable ties, as needed. NOTE: Ensure that the remote start harness is secured in a manner that allows access to the remote start harness programming button and the immobilizer interface module programming button. Page 13 of 23 Vehicle Remote Start System 2014 Tundra Vehicle Remote Start System INSTALLATION PROCEDURES This step is not necessary for vehicle’s equipped with factory security. 1. Place protective tape around the radiator grille sub-assembly. Remove the (4) phillips screws and disengage the (2) clips. 2. Disengage the (4) claws and (3) clips to remove the radiator grille sub-assembly. 3. Locate the empty hole in the passenger’s side of the upper radiator support, near the windshield wiper washer reservoir. Mounting Hole Page 14 of 23 2014 Tundra INSTALLATION PROCEDURES 4. Secure the hood switch bracket to the upper radiator support, using (1) supplied 10 mm bolt and the (1) 10 mm bolt. 5. Install the provided hood pin switch into the bracket. Ensure that the hood pin switch is completely seated. 6. Plug in the corresponding end of the remote start hood switch harness into the bottom of the hood pin switch. 7. Pull back the plastic cover and route the hood pin switch harness under the upper radiator support, to the area in front of the radiator. Page 15 of 23 Vehicle Remote Start System 2014 Tundra INSTALLATION PROCEDURES 8. Secure the hood pin switch harness to the upper radiator support and to the factory harness with (2) cable ties. Cable Ties 9. Disengage the factory hood switch connector, located below the hood latch assembly mounted on the radiator core support. 10.Trim the hood pin switch harness to length. 11. Strip back approximately 1” of the protective covering securing the (2) wires of the hood pin switch harness together to expose the Black and Gray wires. 12. Locate the (2) provided red Scotch-Loks and remove the metal inserts. Apply a layer of dielectric grease to each Scotch-Lok. Reinstall the metal inserts. 13. Partially remove the protective covering on the factory hood switch connector to expose the factory wires. 14. Using the red Scotch-Loks, connect the hood pin switch harness wires to the factory hood pin switch connector. 15. Reinstall the factory hood pin switch connector to it’s original mounting location. REMOTE START Black Gray CAR Scotch-Lok COLOR Blue Red White/Black Red Page 16 of 23 Vehicle Remote Start System 2014 Tundra Vehicle Remote Start System VEHICLE RE-ASSEMBLY 1. Refer again to the vehicle repair manual and reinstall the driver’s knee air bag assembly. S Driver’s knee air bag assembly bolts must be torqued to 10 Nm (7 ft.-lbf). 2. Clean the area of the radiator grill sub-assembly, in front of the hood latch assembly (indicated by the orange box below) with a approved VPC cleaning solution. Ensure the surface is completely dry. 3. Remove the protective backing from the Under Hood Warning Label and place onto the radiator grill sub-assembly. 4. Re-connect the negative battery cable. Torque to 48 in. lbs. 5. Attach the Remote Start Transmitter and Key Tag to the factory ignition key. 6. Place the Remote Start Owner’s Guide in the glove box. Page 17 of 23 Negative Battery Cable 2014 Tundra Vehicle Remote Start System PROGRAMMING IMMOBILIZER & HOOD STATUS SIGNALS STOP Read through the entire procedure before proceeding! Note: Programming procedure must be completed within 60 seconds. 1. 2. Verify that the hood is closed and the ignition is off. Press and hold the brake pedal and the programming button of the remote start harness for 10 seconds. The LED of the remote start harness will turn ON. 3. Verify that the immobilizer interface module LED is blinking Red - Green. 4. Press and release programming button, located on the side of the immobilizer interface module. 5. Verify that the immobilizer interface module LED is blinking Red. 6. Open the vehicle’s hood. 7. Verify that the immobilizer interface module LED is on solid Red. 8. Close the hood. 9. Press and release programming button, located on the side of the immobilizer interface module. 10. Verify that the immobilizer interface module LED is on solid Green for (2) seconds and then turns to solid RED. Note: Vehicle’s NOT equipped with Immobilizer stop here, programming is complete. Vehicle’s equipped with Immobilizer, proceed to Step 11. 11. Start the vehicle. 12. Verify that the LED on the side of the immobilizer interface module turns solid Green for (2) seconds and then turns off. 13. Let vehicle run for at least 5 seconds. 14. Programming complete! Turn vehicle off. 15. Reassemble any removed vehicle interior components, making sure to plug in any connectors that were disconnected during vehicle disassembly. If the Immobilizer Interface Module fails to program, or programs incorrectly, check the following: 1. Repeat Steps 1 - 14 and verify that the programming procedure was completed within the 60 second time limit. 2. Verify that the correct remote start harness wires were connected to the correct vehicle wires and are secure, per the installation manual. 3. Perform reset procedure, located on Page 20 and then repeat Steps 1 - 14 above. Immobilizer Interface Module Programming Button LED Page 18 of 23 2014 Tundra IMMOBILIZER INTERFACE MODULE RESET PROCEDURE Vehicle Remote Start System STOP Read through the entire procedure before attempting to reset the immobilizer interface module. 1. 2. 3. 4. 5. 6. 7. 8. 9. Verify that the hood is closed and the ignition is off. Disconnect all connectors from the from the immobilizer interface module. Press and hold the brake pedal and the programming button of the remote start harness for 10 seconds. The LED of the remote start harness will turn ON. Press and Hold the programming button while connecting the 4 pin connector containing the Red, Black and Blue wires. The LED will turn ON RED for 1 second and then turn OFF. In 3 seconds the LED will begin to flash RED. Immediately release the programming button. The LED will begin turn ON RED for 1 second and then begin flashing a GREEN - RED pattern. Reset Complete. Turn the vehicle’s ignition key to the OFF position. Reconnect all connectors. WARNING! Continuing to hold the programming button after the immobilizer interface module begins to flash GREEN - RED (Step 6) will erase the base software, making the module unusable. Immobilizer Interface Module Programming Button LED Page 19 of 23 PROGRAMMING TACHOMETER SIGNAL STOP 2014 Tundra Vehicle Remote Start System Vehicle MUST be at normal operating temperature before programming the tachometer signal. Failure to ensure that the vehicle is at normal operating temperature may result in a no-start condition and may cause customer dissatisfaction and/or warranty returns. 1. 2. 3. 4. Turn the vehicle’s ignition to the “On” position. Press and hold the brake pedal. Locate the programming button, attached to the remote start harness. Press and hold the programming button for 10 - 15 seconds. The horn will beep and the lights will flash (3) times. 5. Release the programming button and brake pedal. 6. Press and release the programming button. The horn will beep and the lights will flash (4) times. 7. Press and hold the brake pedal. The horn will beep and the lights will flash (1) time, signifying that the remote start is now in “Tachometer Learn Mode”. 8. Start the vehicle. The remote start will flash the parking lights every (3) seconds. 9. Once the vehicle has come to a normal idle (approximately 15 seconds), press and release remote start harness programming button. The horn will beep and the lights will flash (5) times, signifying that the tachometer signal is now “locked in”. 10.Turn vehicle off. TESTING THE REMOTE START SYSTEM Press 2 times within 3 seconds to activate the Remote Start function. Press and hold for 10 seconds to activate the Remote Stop function. Press for Progressive CarFind ® x1= 5 Soft Chirps x2= 5 Louder Chirps x3= 5 Full Volume Chirps Green L.E.D. flash with every button press to confirm proper operation and a good battery. During Remote Start operation, press 1 time to unlock the doors. Press and Hold for Personal Protection Alarm. FUNCTION TEST A. HOOD AJAR STATUS: 1. Make sure all the doors are closed but hood is open and windows are down. 2. Activate the remote start function by pressing the button 2 times within 3 seconds on the 2-way remote control transmitter. The transmitter should beep and flash the led one time. 3. The remote start system should turn the ignition on, but then honk the horn twice and shut down, indicating that the hood is open. The transmitter should beep and flash the led two times. 4. Close the hood. B. KEY-IN-SENSE: 1. Enter the vehicle and close the door. Insert a key into the ignition switch. 2. Activate the remote start function by pressing the button 2 times within 3 seconds on the 2-way remote control transmitter. The transmitter should beep and flash the led one time. 3. The remote start system should turn the ignition on, but then honk the horn two times and shut down, indicating that a key is in the ignition. 4. Remove the key from the ignition. Page 20 of 23 2014 Tundra Vehicle Remote Start System TESTING THE REMOTE START SYSTEM FUNCTION TEST; continued C. BRAKE INPUT: 1. Press the brake pedal. button 2 times within 3 seconds on the 2-way 2. Activate the remote start function by pressing the remote control transmitter. The transmitter should beep and flash the led one time. 3. The remote start system should turn the ignition on and lock the doors, but then honk the horn two times and shut down, indicating that the brake pedal is pressed. 4. Release the brake pedal. D. DOOR STATUS: 1. Open the driver’s door. 2. Activate the remote start function by pressing the button 2 times within 3 seconds on the 2-way remote control transmitter. The transmitter should beep and flash the led one time. 3. The remote start system should turn the ignition on and lock the doors, but then honk the horn three times and shut down, indicating that a door is open while attempting to remote start the vehicle. 4. Close the vehicle door. E. CAR FIND/PANIC: 1. Press the button (1) times on the 2-way remote control transmitter. The horn should honk (5) times and the parking lights should flash (5) times. Repeat this process twice. Subsequent presses within 5 seconds of the first press will honk the horn slightly louder. button on the 2-way remote control transmitter for 3 seconds. The horn should 2. Press and hold the start honking and the lights will flash in a random pattern (Real Panic Sound). The Panic feature can be stopped by pressing the button a second time. F. REMOTE START OPERATION: 1. Close the driver’s door. 2. Activate the remote start function by pressing the button 2 times within 3 seconds on the 2-way remote control transmitter. The transmitter should beep and flash the led one time. 3. Once the vehicle starts, the transmitter should beep (2) times and flash the led (2) times and then flash every few seconds, signifying that the vehicle is still running. Verify that all heat and A/C functions operate normally and that the doors have locked. 4. Once all systems have been checked, pressing the button on the 2-way remote control transmitter, the transmitter should beep (2) times and flash the led (2) times and the doors should unlock. 5. Verify that the vehicle runs for (15) minutes and then shuts down. The doors should lock and the transmitter should beeps (3) times and flash the led (3) times. Function Test Complete! Page 21 of 23 VEHICLE FUNCTION CHECKLIST (These points must be checked to ensure a quality installation) Headlight If the warning lights remains on, it may indicate a system malfunction. Massage Seats (if equipped) High Beams Side Mirror Defogger (if equipped) Turn Signal Lights Front Windshield Defogger (if equipped) Tail Lights Navigation System (if equipped) Stop Lights Rear Sunshade (if equipped) Backup Lights Cruise Control Light (if equipped) Hazard Lights Steering Wheel Audio Control (if equipped) Marker Lights HVAC Dome/Courtesy Lights Power Locks (if equipped) Panel/Switch Illumination Power Windows (if equipped) Accessory Controls/Illumination (If equipped) Gauges Power Side Mirrors (if equipped) Front Wiper/washer Rear Window Defogger (If equipped) Hood Latch Release Key Sensor Buzzer Passenger Air Bag Switch (if equipped) Fog Lights (If equipped) Rollover Side Curtain Air Bag Switch (RSCA) Day Time Running Lights (If equipped) Horn Seat Belt Warning Light If the warning lights remains on, it may indicate a system malfunction. Trunk/Tailgate/Bed Lights (If equipped) Glove Box Light (If equipped) Air Bag Warning Light If the warning lights remains on, it may indicate a system malfunction. ABS Light (If equipped) Rear Wiper/Washer (If equipped) Lamp Failure Sensor If the warning lights remains on, it may indicate a system malfunction. Clock (If equipped) Accessory Power Socket (If equipped) Track/Skid Control Light (if equipped) If the warning lights remains on, it may indicate a system malfunction. Starter Audio/Video (If equipped) Power Rear Door (If equipped) Convenience Memory Settings (If equipped) Heated Seats (If equipped) Page 22 of 23 Tire Pressure Monitoring System (TPMS) Prior to TPMS activation and Pre-Delivery Service (PDS) of the vehicle the TPMS light will blink when IG is turned on. 2014 Tundra TROUBLE SHOOTING Horn Honks Safety Feature 2 Hood opened, Brake Pedal pressed or Key in the ignition 3 Door is open before remote start. 4 No tachometer programmed / No tachometer signal present. 6 Valet/Service Mode engaged SYMPTOM • Vehicle Remote Start System SOLUTION System does not respond to transmitter • • Verify that the antenna is plugged into the back of the remote start module. Verify proper battery voltage in transmitter (3 volts). • Poor operating range • • Verify antenna is mounted in the correct location. Verify that the antenna is plugged into the back of the remote start module. • Vehicle will not unlock using the transmitter. • Verify that the correct vehicle wire was connected to the proper remote start harness wire (Page 11, step 8). • Vehicle does not lock with remote start request. • Verify that the correct vehicle wire was connected to the proper remote start harness wire (Page 11, step 8). • Parking lights do not flash. • Verify that the correct vehicle wire was connected to the correct remote start harness wire (Page 9, step 2). Verify that the fuse located under the DNA case top labeled “PK LIGHTS” is good and installed in the negative position per the Fuse and Jumper Reference Drawing. Verify proper DNA installation. • • • Vehicle’s horn does not honk when activating the Car Find or Panic features. • Verify that the correct vehicle wire was connected to the correct remote start harness wire (Page 9, step 3). • Ignition turns on, horn honks 2 times and the vehicle does not start. Key-In-Sense activated. • • Remove the ignition key from the ignition cylinder. Verify that the correct vehicle wire was connected to the proper remote start harness wire (Page 10, step 4). • Vehicle remote starts, but does not stay running. • Verify that the IMO/IMI wires are properly connected and secure (Page 12, step 10). Verify that the correct vehicle wire was connected to the correct remote start harness wire (Page 10, step 5). Reprogram the vehicle’s tachometer signal. • • While the vehicle is running during the remote start mode, the air conditioning/heater does not operate. • • • Verify that the 8-pin male and female ignition switch connectors are connected properly and secure (Page 9 , step 1). Verify that the fuse located under the DNA case top labeled “HVAC1” and “HVAC2” are good and installed in the positive position per the Fuse and Jumper Reference Drawing. Verify proper DNA installation. Accessing the DNA Card Fuse and Jumper Reference Drawing DOME LIGHT + 2 - 1 2 DOOR LOCKS + DR DOOR/TRNK REL PK LIGHTS - • 1 HVAC 1 *Verify that both rows of multi-pin connectors are aligned and seated properly. HVAC 2 Page 23 of 23 MAIN B+ IGN