Transcript
www.collegehillshonda.com INSTALLATION INSTRUCTIONS PARTS LIST
Accessory
Application
WIRELESS CHARGER
2017 ACCORD 2- AND 4-DOOR
Publications No.
VERSION 1 Issue Date
JUN 2016
4
Self-tapping screws
Wireless Charger Attachment Kit P/N 08U58-T2A-100A Wireless charger harness Urethane tape
Lower tray
Wireless Charger Unit Kit P/N 08U58-T2A-100 Wireless charger unit
8
Wire ties
Accessory user’s information manual
Wire tie with clip
20 A Fuse
Fuse label
Ground bolt
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
08U58-T2A-1000-90
1 of 15
www.collegehillshonda.com TOOLS AND SUPPLIES REQUIRED
INSTALLATION
Phillips screwdriver Isopropyl alcohol Shop towel Diagonal cutters 10 mm and 17 mm Open end wrenches Tape Ratchet 10 mm Socket The following tool is available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. • Trim Tool Set (T/N SOJATP2014) • Plastic Trim Tool (T/N SILTRIMTL10)
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. 2.
Disconnect the negative cable from the battery. If equipped, remove the driver’s dashboard under cover. 2 CLIPS
Illustration of the Wireless Charger on the Vehicle 20 A FUSE
DRIVER’S DASHBOARD UNDER COVER KNOB (Turn.)
3 A FUSE
2 of 15
WIRELESS CHARGER UNIT
QB20201AB
QE20310BC
AII04162-47 (1606)
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com 3.
Remove the driver’s dashboard lower cover and unplug the vehicle connectors.
6.
Remove the driver’s door sill trim.
4-Door: Two retaining tabs and four clips. VEHICLE CONNECTORS
9 CLIPS
2 RETAINING TABS 4 CLIPS
DRIVER’S DOOR SILL TRIM DRIVER’S DASHBOARD LOWER COVER
QB20202AB 20804A
4.
Using the ignition key, unlock the trunk lid/fuel fill door opener, then remove the ignition key. Remove the key cover.
2-Door: Two retaining tabs and six clips.
SELF-TAPPING SCREW
2 RETAINING TABS 6 CLIPS
IGNITION KEY
6 RETAINING TABS KEY COVER
Unlock.
DRIVER’S DOOR SILL TRIM
TRUNK LID/FUEL FILL DOOR OPENER
32102A
DRIVER’S DOOR SILL TRIM
5.
QB20803AB
Remove the self-tapping screw from the trunk lid/fuel fill door opener cover.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
3 of 15
www.collegehillshonda.com 7.
Pull away the door opening seal and remove the driver’s kick panel.
If the vehicle has M/T, go to step 9; otherwise, go to step 14.
M/T models 9. DOOR OPENING SEAL (Pull away)
Attach the tape to the center console panel as shown.
2 CLIPS TAPE
DRIVER’S KICK PANEL QB20805AB
8.
Attach tape to the instrument panel as shown.
CENTER CONSOLE PANEL
QE60801AA
TAPE
TAPE
INSTRUMENT PANEL
INSTRUMENT PANEL BOTTOM VIEW QE12801AC
4 of 15
AII04162-47 (1606)
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com Shift lever knob type A, go to step 10; shift lever knob type B, go to step 12.
Shift lever knob type B 12. Remove the shift lever knob.
Shift lever knob type A SHIFT LEVER KNOB (Turn counterclockwise.)
10. Release the ring and lower the shift lever boot. SECTION VIEW SHIFT LEVER KNOB
SHIFT ROD
2 RETAINING TABS RING SHIFT LEVER KNOB (Turn counterclockwise.) Push
Push
QE60803AA
SHIFT LEVER BOOT
13. Release the shift lever boot. Using a 17 mm open end wrench, remove the lock nut. Go to step 16. SHIFT LEVER BOOT
LOCK NUT (Turn counterclockwise.) SHIFT ROD
SHIFT ROD
SECTION VIEW
LOCK NUT RING
QE60802AA
11. Remove the shift lever knob. Go to step 16. SHIFT LEVER BOOT
SHIFT LEVER BOOT
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
QE60804AA
5 of 15
www.collegehillshonda.com Except M/T models
16. Remove the left center console side trim.
14. Move the shift lever knob to the D position. RIGHT CENTER CONSOLE SIDE TRIM
SHIFT LEVER KNOB (Move to the D position.)
QE12901AC
15. Attach tape to the shift lever knob and center console panel as shown. TAPE
LEFT CENTER CONSOLE SIDE TRIM
SHIFT LEVER KNOB
18. Remove the center pocket and unplug the vehicle connector. CENTER POCKET
QE12902AC
2 SCREWS
6 of 15
QE12903AC
17. Remove the right center console side trim the same way.
VEHICLE CONNECTOR
CENTER CONSOLE PANEL
10 CLIPS
AII04162-47 (1606)
QE12904AC
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com 19. Open the armrest, remove the center console panel, and unplug the vehicle connectors.
20. Remove the vehicle lower tray from the center console panel.
VEHICLE CLIP
VEHICLE LOWER TRAY CENTER CONSOLE PANEL 10 CLIPS
VEHICLE CONNECTORS
2 SCREWS CENTER CONSOLE PANEL
CENTER CONSOLE PANEL
CLIP
QE12906BC
21. Remove the vehicle lower tray lid. 2 CLIPS
ARMREST
VEHICLE LOWER TRAY LID
QE12905AC
2 RETAINING TABS
VEHICLE LOWER TRAY (Do not reuse.)
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
QE13001AC
7 of 15
www.collegehillshonda.com 22. Install the wireless charger unit on the lower tray with four self-tapping screws.
24. Install the lower tray on the center console panel with two screws and one clip removed in step 20.
4 SELF-TAPPING SCREWS
LOWER TRAY
2 SCREWS
CLIP
WIRELESS CHARGER UNIT LOWER TRAY
CENTER CONSOLE PANEL
QE13002BC
QE13004BC
23. Install the vehicle lower tray lid removed in step 21. 25. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Attach the fuse label (3 A WIRELESS CHARGER) on the fuse case.
VEHICLE LOWER TRAY LID
3 A FUSE LABEL
2 CLIPS
FUSE CASE
2 RETAINING TABS
LOWER TRAY
8 of 15
QE13003AC
AII04162-47 (1606)
Clean with isopropyl alcohol.
WIRELESS CHARGER HARNESS
QE13005AC
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com 26. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach. VEHICLE PANEL
Clean with isopropyl alcohol.
If the vehicle is equipped with an accessory 4-pin connector, go to step 29; otherwise, continue with step 28.
Without accessory harness 4-pin connector 28. Plug the wireless charger harness 4-pin connector into the fuse box. Go to step 31. FRONT VIEW
Plug in here.
FUSE BOX
URETHANE TAPE QE13006AC
27. Attach the urethane tape to the vehicle panel as shown.
WIRELESS CHARGER HARNESS 4-PIN CONNECTOR
FUSE BOX
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
QE13007AC
9 of 15
www.collegehillshonda.com Vehicles equipped with an accessory 4-pin connector 29. Unplug the other accessory harness 4-pin connector from the fuse box and plug it into the wireless charger harness 4-pin connector.
If the vehicle is already equipped with another accessory 8-pin connector, go to step 32; otherwise, continue with step 31.
Without accessory harness 8-pin connector 31. Plug the wireless charger harness 8-pin connector into the fuse box. Go to step 34.
OTHER ACCESSORY HARNESS 4-PIN CONNECTOR
FRONT VIEW FUSE BOX
Plug in here.
WIRELESS CHARGER HARNESS 4-PIN CONNECTORS
FUSE BOX
Plug in here.
WIRELESS CHARGER HARNESS 8-PIN CONNECTOR
FUSE BOX QE020201AC
FRONT VIEW FUSE BOX
QE13008AC
30. Plug the remaining wireless charger harness 4-pin connector into the fuse box.
10 of 15
AII04162-47 (1606)
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com With other accessory harness 8-pin connector 32. Unplug the other accessory harness 8-pin connector from the fuse box and plug it into the wireless charger harness 8-pin connector. DUMMY CONNECTOR (Discard.)
If the vehicle is already equipped with other accessory harness, go to step 35; otherwise, continue with step 34.
Without other accessory harness 34. Attach one wire tie with clip around the white tape on the wireless charger harness, then secure the harness to the hole in the vehicle panel with the clip. Go to step 37.
OTHER ACCESSORY HARNESS 8-PIN CONNECTOR
WIRE TIE WITH CLIP
FUSE BOX
WIRELESS CHARGER HARNESS
HOLE
VEHICLE PANEL
WIRELESS CHARGER HARNESS 8-PIN CONNECTORS
WHITE TAPE
Plug in here.
VEHICLE PANEL
WIRELESS CHARGER HARNESS
QE20203AC
FRONT VIEW FUSE BOX
QE20202AC
33. Plug the remaining wireless charger harness 8-pin connector into the fuse box.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
11 of 15
www.collegehillshonda.com With other accessory harness 35. Using diagonal cutters, cut the clip portion off of one wire tie with clip. WIRE TIE WITH CLIP
CLIP
WIRE TIE WITH CLIP
37. Secure the wireless charger harness, wireless charger harness 4-pin connector, and wireless charger harness 8-pin connector to the vehicle harness with two wire ties.
OTHER ACCESSORY HARNESS
WIRELESS CHARGER HARNESS 4-PIN CONNECTOR
VEHICLE HARNESS
WIRELESS CHARGER HARNESS 8-PIN CONNECTOR
Cut off. WHITE TAPE (Align)
WIRELESS CHARGER HARNESS
2WIRE TIES
WIRELESS CHARGER HARNESS
WIRELESS CHARGER HARNESS
QE20204AC
VEHICLE HARNESS
QE20205AC
38. Remove the vehicle ground bolt and secure the wireless charger harness ground terminal to the vehicle ground terminals with one ground bolt. Do not put the ground terminal calkings on top of one another.
36. Attach the cut wire tie with clip around the white tape on the wireless charger harness and secure the wireless charger harness to the other accessory harness with one wire tie with clip.
GROUND BOLT
WIRELESS CHARGER HARNESS GROUND TERMINAL VEHICLE GROUND TERMINALS
12 of 15
AII04162-47 (1606)
VEHICLE GROUND BOLT (Do not reuse.)
QE20206AC
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com 39. Secure the wireless charger harness 12-pin connector and wireless charger harness to the vehicle harness with two wire ties.
40. Align the white tape on the wireless charger harness with the vehicle clip and secure the wireless charger harness to the vehicle harness with one wire tie.
WIRELESS CHARGER HARNESS
VEHICLE CLIP
WIRELESS CHARGER HARNESS
WHITE TAPE (Align.)
WIRE TIE
VEHICLE HARNESS
2WIRE TIES
WIRELESS CHARGER HARNESS 12-PIN CONNECTOR
VEHICLE HARNESS
QE20301AC
WIRE TIE
WIRELESS CHARGER HARNESS
WIRELESS CHARGER HARNESS
VEHICLE HARNESS
WHITE TAPE
QE20304BC
41. Secure the wireless charger harness to the vehicle harness with one wire tie at the white tape on the wireless charger harness.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
13 of 15
www.collegehillshonda.com 42. Secure the wireless charger harness to the vehicle frame with one wire tie at the white tape on the wireless charger harness.
44. Plug the wireless charger harness 7-pin connector into the wireless charger unit. CENTER CONSOLE PANEL
WIRELESS CHARGER HARNESS
VEHICLE CLIP
WIRELESS CHARGER HARNESS 7-PIN CONNECTOR WIRELESS CHARGER UNIT
WIRE TIE VEHICLE HARNESS VEHICLE FRAME WHITE TAPE
WIRE TIE
WIRELESS CHARGER HARNESS
QE20305BC
WIRELESS CHARGER HARNESS CLIP
43. Secure the wireless charger harness to the vehicle harness with one wire tie.
HOLE
CENTER CONSOLE PANEL
QE20306AC
45. Secure the wireless charger harness to the center console panel with one clip on the wireless charger harness. Install the center console panel.
14 of 15
AII04162-47 (1606)
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com 46. Plug the 20 A fuse into the fuse box.
47. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the fuse label to the fuse seal on the driver’s kick panel.
FRONT VIEW Plug in here. FUSE BOX
FRONT VIEW FUSE SEAL
ATTACHING POINT (NO.38) (20A WIRELESS CHARGER) Clean with isopropyl alcohol
FUSE LABEL (20 A WIRELESS CHARGER)
FUSE SEAL
20 A FUSE
FUSE BOX DRIVER’S KICK PANEL
QE20308AC
QE20309AC
48. Check that all wire harnesses are routed properly and all connectors are plugged in. 49. Install all removed parts. 50. Connect the negative cable to the battery. 51. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions. 52. Set the clock (vehicles without navigation).
Check the Operation of the Wireless Charger 53. Check that the wireless charger is working properly as described in the Accessory User’s Information Manual supplied with this kit. 54. Put the wireless charger owner’s manual in the glove box.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved.
AII04162-47 (1606)
15 of 15
