Transcript
Switching Power Supply Type SPD 240W DIN rail mounting • Universal AC input full range • Installation on DIN rail 7.5 or 15mm • Short circuit protection • PFC as standard • High efficiency • Power ready output • LED indicator for DC power ON • LED indicator for DC low • Parallel connection feature • Compact dimensions • UL, cUL listed and TUV/CE approved
Product Description
Ordering Key
The Switching power supplies SPD series are specially designed to be used in all automation application where the
Model Mounting ( D = Din rail ) Output voltage Output power Input Type Optional features
installation is on a DIN rail and compact dimensions and performance are a must.
Approvals
SP D 24 240 1 B
Input type: 1= single phase
Optional Features Description
code
Plug-in connectors
B
Output performances
1)
Model
Output Current (A)
SPD24 SPD48
10 5
Voltage Trim Range1) Min. VDC Max. VDC 22.5 47.0
28.5 56.0
DC @ Start up (VDC) Min. Max. 17.6 37.0
18.4 43.0
Dc low after start up (VDC) Min. Max. 17.6 37.0
Typical Efficiency
18.4 43.0
89% 90%
When S/P switch is set to parallel, it is not possible to trim output voltage.
Output data Line regulation Load regulation Non parallel mode Parallel mode Ouput Voltage accuracy
± 0.5% ± 1% ± 5% +1% (factory adjusted)
Specifications are subject to change without notice
Hold up Time Vi = 115Vac Hold up time Vi = 230Vac Minimum load Parallel Operation (only with S/P switch on “P” position)
25ms 30ms 0% 3 units max.
1
Switching Power Supply Type SPD 240W DIN rail mounting
Input data Rated input voltage Voltage range AC in, 115 selected AC in, 230 selected DC in Rated input current (115/230)
115/230 (autoselect) 93 - 132 Vac 186 - 264 Vac 210 - 370 Vdc 5.4 / 2.2A
Frequency range Inrush current Vi= 115Vac Vi= 230Vac P.F.C. Vi= 230Vac, Ionom.
47- 63 Hz 30A 60A 0.7
Controls and Protections Input Fuse Overvoltage Protection Output Short Circuit Rated Overload Protection
T6.3A/250Vac internal* 120 – 145% Current limit 105-145%
Power ready output (only SPD 24) Threshold voltages Contact rating at 60Vdc insulation
17.6 - 19.4 VDC 0.3A 500Vdc
* Not replaceable by user.
General data (@ nominal line, full load, 25°C ) Ambient temperature Derating (>60°C to +71°C) Ambient humidity Storage Dimensions L x W x D Screw terminal type Plug in connectors
-10°C to 71°C 2.5%/°C 20 - 95%RH -25°C to +85°C
Cooling MTBF (MIL-HDBK-217F) Case material Weight Protection degree
Free air convection 514.000h Metal (powder painted aluminium) 1000g IP20
125 x 83 x 126 142 x 83 x 126
Approvals and EMC Insulation voltage I / O Insulation resistance UL / cUL
3.000Vac 100Mohm UL508 listed, UL60950-1, Recognised EN60950
TUV
CE
EN61000-6-3 EN55022 class B EN61000-3-2 EN61000-3-3 EN61000-6-2 EN55024
Block diagrams L
Vo +
Fuse Line Filter
Inrush Current Limiter and Rectifier
P.F.C. Circuit
Smoothing Circuit
Switching Device
Rectifier
N Y
PWM Controller
Current Detection
Vo Single/Parallel Select
Opto isolation
Reference & Error Amp.
Opto isolation
Over Voltage Detection
Output Level Detection
Vout ADJ.
DCON (Green LED) DCLOW (Red LED) RDY 1) (Relay Contact)
SPD 24 1) For 24V only
2
Specifications are subject to change without notice
Switching Power Supply Type SPD 240W DIN rail mounting
Pin assignement and front controls Pin No. 1 2 3 4 5 6 7 8 9
Designation RDY (only SPD 24) RDY (only SPD 24) + + GND L N DC ON DC LO Vout ADJ. S/P
Description DC OK, relay normally open contact DC OK, relay normally open contact Positive output terminal Positive output terminal Negative output terminal Negative output terminal Ground terminal to minimise High frequency emissions Phase input ( no polarity with DC input ) Neutral input ( no polarity with DC input ) DC output ready LED DC low indicator LED Trimmer for fine output voltage adjustment Single parallel selection switch
Installation
Derating Diagram
VENTILATION / COOLING: • Normal air convection • 25mm of free space along all sides to allow good cooling SCREW CONNECTIONS: • 10-24AWG Flexible or solid cable. 8mm stripping recommended PLUG IN CONNECTORS: • 10-24AWG Flexible or solid cable. 7mm stripping recommended
Power out (%) 100 90 80 70 60 50 40 30 20 10 0 -10 0 5 10 Temperature (°C)
55
60
65
70
75
80
Mechanical Drawings 116 (4.57)
6
10.0 (0.39) 6
I
I DC INPUT
S
S N.C.
N.C.
142.4 (5.59)
125.0 (4.92)
P
125.0 (4.92)
P
AC INPUT 83 (3.27) 7 Specifications are subject to change without notice
9
83 (3.27) 7
9
3
