Transcript
Hyskore
30251
®
SIX GUN SPEED RACK
*Guns, Scopes , Benches, et c. are not include d.
AD GUN ALWAYS UNLO K! CING IN RAC BEFORE PLA
As we acquire more hand guns, the need for organization and storage options increases. As the leader In hand gun storage products, Hyskore® is pleased to introduce the Six Gun Speed Rack. The rack can mount above or below a shelf or to a horizontal or vertical surface. This greatly increases space utilization in gun safes. Out of the box there are 6 barrel inserts that fit .40 cal and larger but can easily be adjusted to fit guns as small as .32 cal. In the course of shipping and packing, parts may end up missing or damagedCall us at 631.673.5975. 8:30 a.m. - 5:00 p.m. Eastern Time. We will promptly send replacements.
Always wear appropriate vision and hearing protection when using this product!
Introduction ALWAYS UNLOAD GUNS BEFORE PLACING IN RACK! The Six Gun Speed Rack was designed to provide hand gun organization and storage opportunities in locations that typically would be unusable space. The rack stores 6 guns each one with a maximum weight of 45 oz. which covers everything from a .32 cal up to, and including, model 1911’s. The barrel inserts are delrin plastic (polyoxymethylene) which is flexible, strong and has a low coefficient of friction. In addition there is an integral collar that protects the muzzle. The shelf-hooks are M-10 steel and the bracket is welded steel with a durable powder coat finish. The speed rack will efficiently organize your guns for many years. The weight of 6 guns can easily exceed 15 lbs. Make sure that the shelf or surface that you attach the rack to has adequate strength and stability to support the load.
ALWAYS UNLOAD GUNS BEFORE PLACING IN RACK!
Page 1
Assembly Instructions 1
Use a hex nut to attach a barrel insert to the frame. Firmly tighten by hand.
2
To reduce the diameter of an insert put the threaded end in a power drill. Hold sandpaper (#150-200 is good) against the shaft and run the drill. About 35-40 seconds should make a good fit for .357/.38. Smaller diameters will take a little longer.
Page 2
3
For above shelf mounting the barrel inserts must be fitted to the angled face of the bracket.
4
Page 3
Attach the shelf hooks as shown. Thread one nut 2.75 on to the shaft . Push the shaft through the tube on the bracket and thread on the other nut. The threaded section is about 7 long. This allows you to adjust the distance from the bracket to the edge of the shelf.
5
If the rod is too long for your shelf, mark the point where you want to cut it and thread a nut past that point. Cut the rod with a hacksaw and unthread the nut. This will clear the thread of any debris or distortion caused by cutting.
6
The shelf hooks will fit shelves up to 11⁄2 thick. For thinner shelves, rotate the hooks as shown and firmly lighten the hex nuts with a wrench. It is especially important to do this when mounting under a shelf.
Page 4
ALWAYS UNLOAD GUNS BEFORE PLACING IN RACK! 7
There are 4 holes in the base of the bracket. Whenever possible use #10 or #12 sheet metal screws to stabilize the base. This step is absolutely necessary for under shelf mounting.
8
Page 5
For under shelf mounting, the barrel inserts attach to the 90/vertical face of the bracket and the shelf hooks also insert from that side. Carefully follow the instructions in steps 5,6 & 7. Especially steps 6 & 7! Failure to properly stabilize and secure the fixture could result in damage to guns.
ALWAYS UNLOAD GUNS BEFORE PLACING IN RACK!
There are 2 ways to mount to a vertical surface. Use the 4 holes at the corners of the angled face of the bracket. From inside the bracket use 4 #10 or #12 screws. This will automatically set the other side of the bracket at the correct angle. The other choice is to position the bracket with the angled side facing up and screw to the surface using the 4 holes in the base.
Mount directly to a flat horizontal surface using the 4 holes in the base.
ALWAYS UNLOAD GUNS BEFORE PLACING IN RACK! Page 6
• REPLACEMENT PARTS • These are replacement parts for purchase. Pictures do not represent contents of set.
30251 - 1
30251 - 2
30251 - 3
Parts List:
30251 - 1 30251 - 2 30251 - 3
Shelf Hooks (2 pcs.).........................................$ 10.00 M-10 Hex Nuts (6 pcs.)..................................... $ 23.00 Barrel Inserts (6 pcs.)........................................$ 10.00
Visit Our Website For More Information or to Check Out Our Other Great Shooting Accessories: www.hyskore.com Send Check or Money Order with Phone Number to: Power Aisle, Inc. P.O. Box 983 Middleburgh, NY 12122 NYS Resident add appropriate% Sales Tax
** $10.00 Shipping & Handling to Lower 48 States** ** $25.00 Shipping & Handling to Alaska, Hawaii, Puerto Rico**
WARRANTY AND DISCLAIMERS HYSKORE /Power Aisle, Inc. guarantees that its products are free from defects in material and workmanship for a period of 90 days from the original date of purchase. This Warranty applies to non-commercial use only. Commercial use voids this warranty. In the event of any defects in material or workmanship, HYSKORE /Power Aisle, Inc.’s sole liability therefore shall be the replacement of any such product(s) and/or components that are defective in material or workmanship. The replacement of any such product(s) and/or components shall be HYSKORE /Power Aisle, Inc.’s sole responsibility. This warranty specifically excludes any and all consequential or accidental damages. No other warranties or liabilities whatsoever are either expressed or implied. If any such warranties shall be imposed by law, not withstanding this provision, then such warranties shall be the responsibility of HYSKORE /Power Aisle, Inc.’s immediate buyer. There shall be no warranties of merchantability, use of trade, or fitness for a particular purpose. Alteration of any product, misuse, or exceeding any stated product limitations voids this warranty. All returns, adjustments, etc. are the responsibility of the retailer/dealer that sold the product. HYSKORE /Power Aisle, Inc. handles return issues through it’s dealers. It should be obvious when using some of these products that approved protective safety gear, including, but not limited to, eye and ear protection, should be utilized. Using the appropriate safety gear is the sole responsibility of the person(s) using the product. It should also be obvious that certain products such as silica gel, etc. must not be consumed, inhaled or taken internally. The user takes full responsibility for inappropriate or incorrect use of these items. In the event an inadvertent event takes place, Material Safety Data Sheets (MSDS) are available on the HYSKORE website. www.hyskore.com. We do not sell guns, scopes, ammunition, cleaning accessories, etc. These accessories are used in many of our product pictures, as props to illustrate how the products are used. As such, they are not included with any product. All photographs, drawings, copy, instructions, etc. are the exclusive property of HYSKORE /Power Aisle, Inc. All downloadable files are intended for the use of the end user of HYSKORE /Power Aisle, Inc.’s products and cannot be reproduced without the express written permission of HYSKORE /Power Aisle, Inc. ©2015 ®
®
®
®
®
®
®
®
®
