31 Series Springer Damper Installation Inst. Caution 31 Series

Transcript

® ® 6900 Marlin Circle La Palma, CA 90623 6900 Marlin Circle La Palma, CA 90623 714.523.8700 Fax 714.523.3220 714.523.8700 Fax 714.523.3220 31 Series Springer Damper Installation Inst. 31 Series Springer Damper Installation Inst. Note: Please read all instructions thoroughly before starting installation. Note: Please read all instructions thoroughly before starting installation. This damper is designed to operate with the shaft up. It must be installed with the cover on top (cover is a larger diameter). Damage to the shock may occur if it is installed with the shaft down. This damper is designed to operate with the shaft up. It must be installed with the cover on top (cover is a larger diameter). Damage to the shock may occur if it is installed with the shaft down. Caution Caution Follow instructions in an authorized shop manual or take the motorcycle to a competent dealer. The correct sleeves must be installed in the top and bottom eye mounts. Your sleeve kit contains four shouldered sleeves and one sleeve that is 7/8" long. The FLSTS models use the 7/8" long single sleeve in the top eye mount and two shouldered sleeves in the bottom eye mount. All other models use two shouldered sleeves in both eyes. The sleeves just press in the eye bushing. The damper is a bolt on replacement for your stock damper. Follow instructions in an authorized shop manual or take the motorcycle to a competent dealer. The correct sleeves must be installed in the top and bottom eye mounts. Your sleeve kit contains four shouldered sleeves and one sleeve that is 7/8" long. The FLSTS models use the 7/8" long single sleeve in the top eye mount and two shouldered sleeves in the bottom eye mount. All other models use two shouldered sleeves in both eyes. The sleeves just press in the eye bushing. The damper is a bolt on replacement for your stock damper. 1. Remove the old damper and note the location of all mounting hardware. 1. Remove the old damper and note the location of all mounting hardware. 2. Install the Progressive Suspension damper and tighten the mounting nuts/bolts to the proper torque specifications (consult your service manual for the correct specifications). 2. Install the Progressive Suspension damper and tighten the mounting nuts/bolts to the proper torque specifications (consult your service manual for the correct specifications). 3. Maintenance: Damper bushings should be checked and cleaned at periodic intervals. 3. Maintenance: Damper bushings should be checked and cleaned at periodic intervals. 4. For a balanced suspension, we highly recommend the installation of a set of our 413 series rear shocks. 4. For a balanced suspension, we highly recommend the installation of a set of our 413 series rear shocks. Rev. B Rev. B #3053-006 www.progressivesuspension.com Copyright © 2001 by Progressive Suspension, Inc. All Rights Reserved. #3053-006 www.progressivesuspension.com Copyright © 2001 by Progressive Suspension, Inc. All Rights Reserved. ® ® 6900 Marlin Circle La Palma, CA 90623 6900 Marlin Circle La Palma, CA 90623 714.523.8700 Fax 714.523.3220 31 Series Springer Damper Installation Inst. 714.523.8700 Fax 714.523.3220 31 Series Springer Damper Installation Inst. Note: Please read all instructions thoroughly before starting installation. Note: Please read all instructions thoroughly before starting installation. This damper is designed to operate with the shaft up. It must be installed with the cover on top (cover is a larger diameter). Damage to the shock may occur if it is installed with the shaft down. This damper is designed to operate with the shaft up. It must be installed with the cover on top (cover is a larger diameter). Damage to the shock may occur if it is installed with the shaft down. Caution Caution Follow instructions in an authorized shop manual or take the motorcycle to a competent dealer. The correct sleeves must be installed in the top and bottom eye mounts. Your sleeve kit contains four shouldered sleeves and one sleeve that is 7/8" long. The FLSTS models use the 7/8" long single sleeve in the top eye mount and two shouldered sleeves in the bottom eye mount. All other models use two shouldered sleeves in both eyes. The sleeves just press in the eye bushing. The damper is a bolt on replacement for your stock damper. Follow instructions in an authorized shop manual or take the motorcycle to a competent dealer. The correct sleeves must be installed in the top and bottom eye mounts. Your sleeve kit contains four shouldered sleeves and one sleeve that is 7/8" long. The FLSTS models use the 7/8" long single sleeve in the top eye mount and two shouldered sleeves in the bottom eye mount. All other models use two shouldered sleeves in both eyes. The sleeves just press in the eye bushing. The damper is a bolt on replacement for your stock damper. 1. Remove the old damper and note the location of all mounting hardware. 1. Remove the old damper and note the location of all mounting hardware. 2. Install the Progressive Suspension damper and tighten the mounting nuts/bolts to the proper torque specifications (consult your service manual for the correct specifications). 2. Install the Progressive Suspension damper and tighten the mounting nuts/bolts to the proper torque specifications (consult your service manual for the correct specifications). 3. Maintenance: Damper bushings should be checked and cleaned at periodic intervals. 3. Maintenance: Damper bushings should be checked and cleaned at periodic intervals. 4. For a balanced suspension, we highly recommend the installation of a set of our 413 series rear shocks. 4. For a balanced suspension, we highly recommend the installation of a set of our 413 series rear shocks. Rev. B Rev. B #3053-006 www.progressivesuspension.com Copyright © 2001 by Progressive Suspension, Inc. All Rights Reserved. #3053-006 www.progressivesuspension.com Copyright © 2001 by Progressive Suspension, Inc. All Rights Reserved.