Transcript
Instructions.
LVL Stand Alone Wiring Models: 566025, 566026, 566042,115VAC Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.
ELECTRIC SHOCK HAZARD Improper grounding, setup, or usage of the system can cause electric shock. •
Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.
•
Connect only to grounded power source.
•
All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.
313300B
Control Wiring
Control Wiring CONTROL WIRING
1L1
1L2
GROUNDING
1L3
FORWARD RUN CONDITION POWER (SEE NOTE #8) NOMINAL 115Vac/50/60Hz/1Ph 1TB-1
1TB-2 BK/18
1TB-3
WH/18
M
INDICATES FIELD WIRING
1FU 3.0 AMP (SLO-BLO)
GN/14 GN/14
GN/14
BK/18 1TGS ON-OFF SWITCH (15 AMP)
MAIN POWER SWITCH
TIMER MTG PANEL GND SCREW
WH/18
BK/18 BK/18
1TB-4
TRANS MTG PANEL GND SCREW
1CR-B 8
BK/18
5
1TR
1TR-11 BK/18
1TR
BK/20
R/18
3
1
1TR-2 BK/18
1TR-9
R/18
WH/20 1TR-2 WH/18
M
1TB-7
See Note 6
1TB-9
1JPR
1TB-9
1TR-3
1PB
BL/18
BL/18
1TR-6
WH/18
1TR-10 1LT Y/20
1TB-5 1FS
R/20
1TB-5
R/20
WH/20
G
R/20 A
1TB-16
WH/20
1CR
B
BK/20
POWER "ON" INDICATOR
1TB-10
LOW OIL INHIBIT
WIRING DETAILS UNUSED RELAY CONTACTS 1CR-A
WH/20 OR/20
1TB-6
1TB-10
1CR-A 7
2LT OR/20
OR/20
1
WH/20
R
1TB-19
LOW OIL INDICATOR
7
1CR-C 9
BK/20
5
6
4
2
2
1CR-C 9
3
4 TERMINAL LOCATION
115Vac/50/60Hz PRIMARY 24Vdc SECONDARY STEP DOWN TRANSFORMER BK/20 WH/20 BK/20
1CR-B 8
1TB-11
1TB - FRONT-TIMER MTG PANEL UNUSED TERMINALS WH/20
1
1TB - 8, 20 WIRE COLOR ABBREV.
1T (30VA) 9
BL/20
WH/20
BK = BLACK BL = BLUE BR = BROWN GY = GRAY GN = GREEN OR = ORANGE
7
AC1 R/20
(+) R1 56K 2W
BK/20
(-)
1BR
PK = PINK R = RED V = VIOLET WH = WHITE Y = YELLOW
AC2 BK/18
R/18 C1 550uF (+)
(OPTIONAL) J1 +34V
R/22 1TB-12
BR(R)
BK/22
PROX1 IN
BK(WH)
J5
1TB-14
PROX RET
GRD 1PRS
J2
SOL1 RET SOL2 RET
JPR (OPTIONAL) (SEE NOTE #7)
PROXIMITY SWITCH (10-30Vdc)
J8
BK/22
J6
1TB-15
PROX2 IN
806121 PWB ASSY
1TB-18 1 POT 2.5K OHM .5 WATT
OR/22 BL/22
J10
TIME1 ADJ C
J11
TIME2 ADJ A
J12
TIME2 ADJ B
J13
TIME2 ADJ C
J14
2SOL
1TB-17
V/22
J9
TIME1 ADJ B
1SOL
BR/22
J7
TIME1 ADJ A
BL/22 OUTPUT
+24V
J3
34V RET
1TB-13
+12V
BL(BK)
J4
1PWB
OR/22
2 POT 2.5K OHM .5 WATT
BL/22
(OPTIONAL)
(OPTIONAL)
BR(R)
NOTE: WITH POT TURNED CLOCKWISE THE ORANGE WIRE IS SOLDERED TO THE HIGH OHM READING.
+12V OUTPUT
BL(BK)
BLUE (COMMON)
BK(WH)
GRD 2PRS
PROXIMITY SWITCH (10-30Vdc)
LAYOUT
ORANGE
ON OFF 1PB
1TGS
1FU
GROUND 1LT
2LT
G
R
POWER
LOW OIL LEVEL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1TB
ENCLOSURE COVER FRONT
FRONT- TIMER MTG PLATE
1CR GROUND 1R
115Vac +
1BR 1C 1T FRONT- TRANS MTG PLATE
2
313300B
Control Wiring
Notes: 1. Customer responsible for fusing and supplying ON/OFF controls for external wiring. 2. BK / 18 = Wire Color / AWG = Black /18 AWG 3. Do not exceed 2 wires per TB side 4. When one proximity switch is used to operate 2 solenoids, install jumper between 1TB-13 and 1TB-15. 5. Forward run condition power to be suppled only when conveyor is running in the forward condition. When conveyor is off or running in reverse, power must be removed. 6. 1 JPR from 1 TR-3 to 1 TR-6 is required for operation. 7. Motor wires: BK to BK WH to WH GN to GN Cap R 8. Set timer operating mode to Cu-c
313300B
3
Graco Information TFor the latest information about Graco products, visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 313300
Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 Copyright 2008, Graco Inc. is registered to ISO 9001 www.graco.com Revised 07/2009
