Transcript
Model 3142E–PA 118523-118524 clampset
118490 Kit – Included Parts RFC-NMS-100-NFS-32 Antenna cable (32-inch)
Model 3142E–PA FOR EMISSION MEASUREMENTS
ONLY
118490 Preamplifier
– 6 GHz Operating Freq Range: 30 MHz – +75°C
Operating Temp Range: -20°C
The ETS-Lindgren Model 3142E-PA is designed to amplify a signal in the 30 MHz to 6 GHz frequency range. On/off For emission measurements only.
930621 M6 screw (2)
410052 220V Power supply
Power connector
Power cable to power source
Model 3142E–PA FOR EMISSION MEASUREMENTS
ONLY
– 6 GHz Operating Freq Range: 30 MHz – +75°C Operating Temp Range: -20°C
117857 Power cable
410564 120V Power supply
118522 Bracket
910697 1/4–20 screw (3)
Coaxial cable to spectrum analyzer (not included; customer-supplied)
110221 knob RF out RF in
Product Information Bulletin See the ETS-Lindgren Product Information Bulletin included with your shipment for the following:
• • Safety, regulatory, and other
• • ETS-Lindgren calibration service
• Steps to receive your shipment
• ETS-Lindgren contact information
Warranty information
product marking information
Use only this mounting hole for 118523-118524 clampset
Steps to return a component for service
Safety Information WARRANTY
Use both mounting holes for 118522 bracket
Antenna cable to Model 3142E
Warranty Information
ONLY QUALIFIED PERSONNEL should install, operate, or service this equipment.
For complete warranty information, see the Product Information Bulletin.
For complete safety information, see the Product Information Bulletin.
To Model 3142E
The Model 3142E-PA includes two brackets for mounting: 118522 bracket for 2170B/2171B towers
118523-118524 clampset with 110221 knob for 2070B/2071B towers and other towers/tripods with 2-in x 2-in boom
The Model 3142E-PA includes a 120V power supply, a 220V power supply, and a power cable that can be used with either power supply. USA Headquarters Phone: +1.512.531.6400
[email protected]
• 120V Power Supply, part# 410564 • 220V Power Supply, part# 410052 • Power Supply Cabling, part# 117857
Please see www.ets-lindgren.com for a list of all ETS-Lindgren offices. © Copyright 2012–2013 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied by any means without written permission from ETS-Lindgren Inc. The ETS-Lindgren logo and BiConiLog are trademarks of ETS-Lindgren Inc.; LEMO is a registered trademark of LEMO SA.
399363, Rev B
Revision/Date: A, Initial Release - October, 2012 B, Update specs - April, 2013
You will assemble the power supply cable by connecting the two cable lengths together.
Note: ETS-Lindgren may substitute a similar part with the same functionality for another part.
www.ets-lindgren.com
www.ets-lindgren.com
Model 3142E–PA
Before placing into service, read Safety Information on the back page of this document.
Using the 118522 Mounting Bracket
Using the 118523-118524 Mounting Clampset
Use the 118522 bracket to mount the Model 3142E-PA onto the back side of the carrier on the 2170B/2171B tower. Point the antenna connector upward.
Use the 118523-118524 clampset to mount the Model 3142E-PA onto the bottom side of the boom on a 2070B/2071B tower and other towers/tripods with a 2-in x 2-in boom. Point the antenna connector downward.
Bottom view
Side view
1
To 3142E-PA 910697 1/4–20 screw (2)
1
Assemble 118523 and 118524 clamps around boom and Model 3142E-PA
2
Insert 110221 knob through hole in both clamps
2-in x 2-in boom
Model 3142E-PA
2 To tower
3
930621 M6 screw (2)
Preamplifier Electrical Specifications Operating Frequency Range
30 MHz – 6 GHz
Amplifier Gain (Typical)
55 dB MIN
Maximum Continuous Input
0 dBm
Power Output
+20 dB MIN @ 1 dB PT
Operating Temperature Range
-20°C to +75°C (-4°F to +167°F)
DC Power Supply
+12 VDC – +15 VDC 450 mA NOM
Insert 910697 1/4–20 screw through hole in clamp and into hole in 3142E-PA
Preamplifier Physical Specifications Connectors
Dimensions
• RF input, N male • RF output, SMA female • Power supply, 2-pin LEMO® • Length: 13.97 cm (5.5 in) • Height: 8.89 cm (3.5 in) • Depth: 3.86 cm (1.52 in)
www.ets-lindgren.com
