Transcript
PoE EXTENDER Component of TE’s Powered Fiber Cable System The PoE Extender is a component of TE Connectivity’s (TE’s) powered fiber cable system, a hybrid optical fiber/copper cable system for remote powering of network access devices. It is designed to simply and easily function with the powered fiber cable system to extend the distance of PoE (Power over Ethernet) enabled devices. The PoE Extender encompasses four primary elements: 1.
Environmentally sealed closure - IP67
2.
Electrical power management
3.
Circuit protection electronics
4.
Optical to electrical Media Conversion
When coupled with any standard NEC Class II 48V DC power supply TE’s powered fiber cable system can power and communicate with PoE standard devices at far greater distances than “category style” copper cabling systems which are typically limited to 100 meters, and still meet NEC Class II and SELV standards, eliminating the need for qualified electricians during installation. The PoE Extender also contains circuit protection and DC/DC conversion electronics which automatically condition electrical voltage to the correct level needed for PoE input to the device under load (such as a small cell, high definition security camera, Wi-Fi hot spot, etc.).
BROADBAND NETWORK SOLUTIONS /// PoE EXTENDER
PoE Extender
Component of TE’s Powered Fiber Cable System WHY PROTECT REMOTELY POWERED CIRCUITS? Long length DC low voltage electrical systems are at increased risk of: •
AC cross from high voltage cables
•
Higher current in the event of a short circuit
•
Strong electrical surges due to lightning strikes or other EM events in close vicinity
The PoE Extender provides three levels of electrical protection: •
1 •
2 •
3
Primary Protection: – Gas discharge tube - will activate for high voltage surges – Protects both differential and common mode – GDT component rated to 40kA surge protection Secondary Protection: – Metal oxide varristors - operates for slower surges as well as fast surges
Interior Electrical Board
– Protects both differential and common mode – MOV components rated to 4.5kA Tertiary Protection: – Transient voltage suppressors - works at relatively low/slow surges, adds an extra layer of protection against voltage spikes – Protects differential mode only – Prevents the voltage from rising above 80-100V
Interior Cable Routing Tray
Additional protection elements include: •
Cross-polarity protection to simplify installation - the circuit will work regardless of the input polarity
•
AC cross protection: –
6A replaceable fuses (TR5 package)
–
No exposed high voltage pads
•
High power inductors used as coordinating elements to maximize energy efficiency
•
Sealed enclosure for environmental protection
BROADBAND NETWORK SOLUTIONS /// PoE EXTENDER
PAGE 2
PoE Extender
Component of TE’s Powered Fiber Cable System SPECIFICATIONS Environmental Characteristics Storage Temperature: Operating Temperature: Installation Temperature: Ingress Protection:
-40° to 70°C -40° to 65°C 65°C assumes 45°C ambient air temperature, plus 20°C sun loading -5° to 45°C IP67
Mechanical Characteristics Weight: 0.9kg Closure Dimensions: 170mm x 125mm x 69mm Electric Transmission Characteristics Maximum Output:
25.5W, PoE+ rated output NEC Class II requires a power supply unit (PSU) limited to less than 60V DC. In practice, some commercial “48V“ power supplies may be configured to output from 48V up to about 57V. A range of PSU voltage outputs is represented, along with the two Powered Fiber Cable copper gauge options, with supported maximum distances in meters. Note: PoE standard (IEEE 802.3af) assumes 15.4W power consumption PoE+ standard (IEEE 802.3at) assumes 25.5W power consumption.
Input Voltage Maximum (57V)
PoE/PoE+
Max Recommended Cable Length (Meters)
12
PoE
3040
12
PoE+
1560
Cable Gauge (AWG)
16
PoE
1190
16
PoE+
610
Input Voltage
Cable Gauge (AWG)
PoE/PoE+
Max Recommended Cable Length (Meters)
Nominal (48V)
12
PoE
2150
Input Voltage Minimum (40.5V)
12
PoE+
1100
16
PoE
850
16
PoE+
430
Cable Gauge (AWG)
PoE/PoE+
Max Recommended Cable Length (Meters)
12
PoE
1530
12
PoE+
780
16
PoE
600
16
PoE+
310
Communications Characteristics Optical Input: Singlemode: 50um Multimode: PoE+ Media Converter: RJ45 Connector Output, Half Duplex and Full Duplex Modes Supported 10/100/1000Mb Ethernet
When using the TE recommended power supply, the maximum (57VDC) voltage from the power supply may be assumed for determining distances supported.
If another 48VDC power supply is used refer to the distances listed for nominal (48V).
The minimum (40.5V) is only shown for those customers who utilize an unregulated power supply directly from a UPS source. This is not recommended by TE, but provided for illustrative purposes only.
Accepts standard SFP (Small Form-factor Pluggable) transceivers ITU-T G657.A2 OM3 or OM4 Duplex OM3 = 100Mb @ 1 km Simplex SMF = 1Gb @ 1km
BROADBAND NETWORK SOLUTIONS /// PoE EXTENDER
PAGE 3
PoE Extender
Component of TE’s Powered Fiber Cable System COMPLIANCES: • RoHS (2002/95/EC) • REACH SVHC, 53 6/20/11 • ITU.T K21 - Enhanced test level • SELV and NEC Class II • IEC 60529 • IP67 • EN 300.019-1-4 Class 4.1E • EN 60950 • EN 55022 – emissions • EN 55024 - immunity • ITU.T G657.A2 singlemode specification • IEC 60793-2-10 type A1a.2, and ISO/IEC 11801 OM3/OM4 multimode specifications
ORDERING INFORMATION Part Number PFU - P - _ - _ - _ _ _ - _ _
Enclosure Plate
Port Count
A
Aruba
B
Universal Bracket
01
Output Power
Indoor/Outdoor O
1-Port
001
Outdoor
30W
TE CONNECTIVITY BROADBAND NETWORK SOLUTIONS REGIONAL SALES HEADQUARTERS: North America Greensboro, NC, USA Ph: +1-800-553-0938 Fx: +1-717-986-7406
Latin America Buenos Aires, Argentina Ph: +54-11-4733-2200 Fx: +54-11-4733-2282
Europe Kessel-Lo, Belgium Ph: +32-16-35-1321 Fx: +32-16-35-2188
Mid East & Africa Cergy-Pontoise, France Ph: +33-1-3420-2122 Fx: +33-1-3420-2268
te.com TE Connectivity, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2015 TE Connectivity Ltd. family of companies All Rights Reserved. 319581.2AE 05/15 Revision
BROADBAND NETWORK SOLUTIONS /// PoE EXTENDER
Asia Hong Kong, China Ph: +852-2735-1628 Fx: +852-2735-1625
Pacific Sydney, Australia Ph: +61-2-9554-2600 Fx: +61-2-9554-2519
PRODUCT SHEET Contact us P.O. Box 1101 Minneapolis, Minnesota USA 55440-1101 Tel: 1-800-366-3891 x73000 1-952-917-3000 Fax: 1-952-917-3237 www.te.com/bns www.te.com/PoweredFiber
