Transcript
PU
SH
ON-O
FF
Dimmer/ Fan Controller 31E1000L Series
Installation Instructions
31E1000L Series
Dimmer/Fan Controller Installation Instructions
Table of Contents 1.0
Product Range........................................................................................3
2.0
Description..............................................................................................3
3.0
Features...................................................................................................3
3.1 Soft Start Operation............................................................................................. 3
3.2 Unloaded LV Iron-core Transformer Cut-out......................................................... 3
3.3 Over Temperature Compensation........................................................................ 3
4.0
Compatible Loads..................................................................................3
5.0
Unit Operation.........................................................................................4
6.0
Installation Instructions........................................................................4
6.1 Wiring Details....................................................................................................... 4
6.2 Minimum Brightness Settings............................................................................... 4
6.3 Low Voltage Lighting Transformers....................................................................... 4
6.4 Multi-gang Derating.............................................................................................. 4
6.5 Ceiling Fans.......................................................................................................... 4
7.0
Product Specifications...........................................................................6
8.0
Mechanical Specifications.....................................................................7
9.0
Warranty Statement................................................................................8
Copyright Notice The concepts, products and designs described in this document are the subject of international patents, and protected by international law. Copyright Clipsal Australia Pty Ltd. All rights reserved.
Trademarks • Clipsal is a registered trademark of Clipsal Australia Pty Ltd. • C-Thru® - The Clear Choice, is a registered trademark of Clipsal Australia Pty Ltd. All other logos and trademarks are the property of their respective owners.
Disclaimer Clipsal Australia Pty Ltd reserves the right to change specifications or designs described in this manual without notice and without obligation. 2 of 8
© Clipsal Australia Pty Ltd
31E1000L Series
Dimmer/Fan Controller Installation Instructions
1.0 Product Range 31E1000L 2031E1000L
Dimmer, leading edge, 1000W, 240V, 50Hz, (Standard) Dimmer, leading edge, 1000W, 240V, 50Hz, (2000 Series)
2.0 Description The Clipsal 31E1000L Series Dimmer/Fan Controller, rated at 1000W (4A), gives full control of lighting and fans in domestic and commercial applications. The dimmer complies with the Australian Standards (AS/NZS1044, AS/NZS4051) for EMC. An integral push-on/push-off switch is incorporated into the knob, which also controls the lamp brightness or fan speed.
3.0 Features 3.1 Soft Start Operation The 31E1000L Series dimmers incorporate a soft start feature, providing a noticeably smooth lamp illumination at turn on. This feature also minimises lamp filament start up stress, which may increase lamp lifetime.
3.2 Unloaded LV Iron-core Transformer Cut-out The 31E1000L Series dimmers incorporate a safety cut-out, reducing the possibility of low voltage transformers overheating when a load (lamp) is not present (or has blown). Under these circumstances, normal dimmer operation can be restored by switching the dimmer off before replacing the faulty lamp.
3.3 Over Temperature Compensation The 31E1000L Series dimmers incorporate thermal overload compensation, which automatically reduces lamp brightness should the dimmer be inadvertently overloaded.
4.0 Compatible Loads • Incandescent or halogen 240V lamps • Low voltage lighting with iron-core transformers • Exhaust fans i.e shaded pole induction motors • Ceiling fans i.e split-phase induction motors • Any combination of the above specified load types. Not recommended for low voltage lighting with electronic transformers, unless used in conjunction with inductor unit, cat. no. 32EIND (limited to 2A max. load). Not suitable for fluorescent lighting.
© Clipsal Australia Pty Ltd
3 of 8
31E1000L Series
Dimmer/Fan Controller Installation Instructions
5.0 Unit Operation The dimmer controller is switched on or off by pressing the controls on/off knob. Brightness (or fan speed) is adjusted by rotating the control knob; clockwise increases brightness (or fan speed), anticlockwise decreases brightness (or fan speed). Pressing the on/off switch does not alter the level setting.
6.0 Installation Instructions 6.1 Wiring Details Connect the 31E1000L in accordance with the wiring diagrams (the wiring diagrams equally apply for fan applications).
6.2 Minimum Brightness Settings The minimum brightness level has been factory set to suit incandescent or iron-core based low voltage lamp applications. The minimum setting trimming potentiometer, which is accessible through the side of the case, can be adjusted (if required), using the small plastic screwdriver supplied. When the 31E1000L Series is used to control fan loads it will typically be necessary to advance the minimum setting towards the fully clockwise position. This setting allows smooth control of fan rotational speed over the full range of the control knob, and prevents the motor stalling at low speed settings.
6.3 Low Voltage Lighting Transformers Typically, dimmer load ratings must be derated in order to account for low voltage lighting transformer inefficiency. The 31E1000L dimmer does not require such derating, and is capable of driving the full 1000W of iron-core based low voltage lighting lamps (e.g. 20 x 50W lamps).
6.4 Multi-gang Derating For applications, where 31E1000L dimmers are multi-ganged or mounted in close proximity to each other, the maximum load rating is to be derated to 750W (3A). The over temperature compensation feature may reduce the maximum attainable brightness if dimmers are too closely spaced.
6.5 Ceiling Fans Some ceiling fan models produce audible humming noise when used in conjunction with phase-control fan speed controllers.
4 of 8
© Clipsal Australia Pty Ltd
31E1000L Series
Dimmer/Fan Controller Installation Instructions
1 WAY SWITCHING
INCANDESCENT LOAD
LOAD 1-WAY LINE 2-WAY LOOP
NEUTRAL LINE
2 WAY SWITCHING
INCANDESCENT LOAD
LOAD 1-WAY LINE 2-WAY LOOP
© Clipsal Australia Pty Ltd
1-WAY 2-WAY
NEUTRAL LINE
5 of 8
31E1000L Series
Dimmer/Fan Controller Installation Instructions
7.0 Product Specifications Parameter
Value
Nominal Operating Voltage
220 - 240V a.c.
Nominal Operating Frequency
50Hz
Maximum Load
1000W 1000W 1000VA
Incandescent lamps Iron-core based LV lighting Fan motors
(4A) (4A) (4A)
*Derate to 750W for multi-gang applications (3A) Minimum Load
20W 20W 40VA
Dimming Technique
Leading edge phase control
Compatible Loads
Incandescent lamps Iron-core based LV lighting Fan motors
(0.1A) (0.1A) (0.2A)
Incandescent lighting Halogen 240V lamps Low voltage lighting with electronic transformers
M
- Exhaust fans (shaded pole induction motors) - Ceiling fans (split-phase induction motors)
Operating Temperature Range
0 to 40°C
Operating Humidity Range
10 to 90% R.H.
Mounting Centres
84mm Australian Pattern Plate
Shipping Weight
180g
EMC Emission Compliance
6 of 8
AS/NZS1044 AS/NZS4051
Specifications typical @ 240V , 25°C ± 5°C
© Clipsal Australia Pty Ltd
31E1000L Series
Dimmer/Fan Controller Installation Instructions
8.0 Mechanical Specifications 72
U
P
115
SH
46
70 ON -O FF
45
Dimensions are in millimetres. No user serviceable parts inside.
© Clipsal Australia Pty Ltd
7 of 8
9.0 Warranty Statement 1. The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to the Clipsal product, which the consumer has under the Commonwealth Trade Practices Act or any other similar state or territory laws. 2. The warrantor is Clipsal Australia Pty Ltd of 33-37 Port Wakefield Road, Gepps Cross, South Australia 5094. With registered offices in all Australian states. 3. This Clipsal product is guaranteed against faulty workmanship and materials for a period of two (2) years from the date of installation. 4. Clipsal Australia Pty Ltd reserves the right, at its discretion, to either repair free of parts and labour charges, replace or offer refund in respect to any article found to be faulty due to materials, parts or workmanship. 5. This warranty is expressly subject to the Clipsal product being installed, wired, tested, operated and used in accordance with the manufacturer’s instructions. 6. All costs of a claim shall be met by Clipsal Australia Pty Ltd, however should the product that is the subject of the claim be found to be in good working order all such costs shall be met by the claimant. 7. When making a claim the consumer shall forward the Clipsal product to the nearest office of Clipsal Australia Pty Ltd with adequate particulars of the defect within 28 days of the fault occurring. The product should be returned securely packed, complete with details of the date and place of purchase, description of load, and circumstances of malfunction.
Clipsal Australia Pty Ltd
clipsal.com
A member of Schneider Electric
Contact us: clipsal.com/feedback National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
Clipsal Australia Pty Ltd reserves the right to change specifications, modify designs and discontinue items without incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be liable for any error therein. © Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted. CLIPCOM 21364 June 2010 F2238/02
