Transcript
an ISO 9001:2008 Registered Company
18” ELECTRIC FAN INSTALLATION INSTRUCTIONS 32018-VUF___32018-VUQ___
902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 1 OF 7
Table of Contents
PAGES 1. COVER 2. TABLE OF CONTENTS 3. PACKING LIST 4. MOTOR/FAN INSTALLATION 5. THERMOSTAT INSTALLATION 6. WIRING DIAGRAM 7. ELECTRIC FAN PACKING LIST
2 902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 2 OF 7
18” ELECTRIC FAN PACKING LIST No.
QTY.
1.
1 1 1 1 1 8 1 1 1 3 3 3 4 4 1 1
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
PART No. 32001-VUQ 32001-VUB 32720-VUF 40155-VUT 49457-VUI 18233-VUB 18100-VUG 40130-VUB 23100-VUW 18287-VUB 18136-VUB 18098-VUB 18250-VUB 18150-VUB 23102-VUW 23136-VUW
DESCRIPTION CHROME FAN BRACKET PLAIN FAN BRACKET FAN BLADE/ MOTOR ADJUSTABLE FAN THERMOSTAT CONTROL KNOB #6 x 3/8” PAN HEAD SCREW 1/4” COMP. MALE HALF UNION ADJ. FAN SENSOR BRACKET FUSE HARNESS 1/4” x 1/2” BOLTS 1/4” COARSE BOLT 1/4” LOCK WASHER 10/32 x 1/2” SCREW 10/32 MACHINE NUT ELECTRIC FAN WIRING HARNESS 70 AMP SINGLE SPEED FAN HARNESS
3 902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 3 OF 7
18” ELECTRIC FAN KIT 32018-VUF/ 32018-VUQ
IMPORTANT-PLEASE READ CARFULLY IT IS NECESSARY THAT THE ELECTRIC FAN KIT BE INSTALLED IN ACCORADANCE WITH THE FOLLOWING INSTRUCTIONS. IMPROPER INSTALLTION OR APPLICATION OF ELECTRIC FAN KIT MAY RESULT IN PREMATURE FAILURE.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE BEGINNING INSTALLATION STEP 1
MOUNT MOTOR SUPPORT BRACKET TO MOTOR USING (3) 1/4” x 1/2” BOLTS, LOCK WASHERS AND NUTS SUPPLIED. SEE FIGURE 1. DO NOT TIGHTEN COMPLETLEY UNTIL STEP 3.
STEP 2
A STRONG, SECURE MOUNTING IS REQUIRED FOR FAN BRACKETS. MARK HOLES BY HOLDING FAN IN POSITION AND MARKING THRU MOUNTING HOLES. MOUNT FAN & BRACKET WITH SCREWS & NUTS PROVIDED. SEE FIGURE 2.
STEP 3
NOW TIGHTEN AND CHECK ALL NUTS AND BOLTS.
FAN MOTOR MOTOR SUPPORT BRACKET
FIGURE 1 FRONT VIEW
SPAN-26” x 30¼” IF YOU WANT A SPAN SMALLER THAN 26” CUT BRACKET LEGS AS REQUIRED. SEE FIGURE 3.
CUT
BRACKET LEGS CUT BRACKET LEGS
FIGURE 3 FRONT VIEW
MOTOR SUPPORT BRACKET
1/8” MOTOR SUPPORT BRACKET
(4) 10/32 x 1/2” BOLTS & NUTS
FIX BRACKET LEGS TO MOTOR BRACKET WITH SCREW. FRONT VIEW SEE FIGURE 4. OPTIONAL: ROSETTE WELD THRU SCREW HOLE IN TUBING INSTEAD OF THE SCREW TO PERMANENTLY FIX BRACKET LEGS TO MOTOR BRACKET.
3/32”
FIGURE 2
902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 4 OF 7
FIGURE 4 REAR VIEW
4
FAN THERMOSTAT INSTALLATION INSTRUCTIONS REMOVE RADIATOR DRAIN COCK RADIATOR. APPLY TEFLON TAPE TO CONNECTOR AND SCREW INTO RADIATOR DRAIN COCK FLANGE AND TIGHTEN WITH 9/16” WRENCH. POSITION SLEEVE AT 1⁄” FROM TIP OF SENSOR. SEE FIGURE 5.
TEFLON HERE
1⁄”
THEREMO LEAD
NUT
SLEEVE
THEREMO SENSOR
CONNECTOR
INSERT SENSOR INTO CONNECTOR ON RADIATOR AND HAND TIGHTEN NUT. SEE FIGURE 6.
CONTROL KNOB THERMOSTAT SWITCH
THERMOSTAT SENSOR CONNECTOR USING A 1/2” WRENCH ON NUT AND A 9/16” WRENCH ON CONNECTOR, SNUG BOTH FITTINGS TOGETHER. OVERTIGHTENING THESE CONNECTIONS MAY RESULT IN DAMAGE OR FAILURE. ATTACH THERMOSTAT SWITCH TO THERMOSTAT MOUNTING BRACKET AND MOUNT IN A POSITION WHERE IT WILL NOT BE DAMAGED OR SUBJECT TO EXCESSIVE MOISTURE.
CALIBRATING THERMOSTAT INSTALL COOLANT INTO COOLING SYSTEM. START ENGINE. ROTATE THERMOSTAT CONTROL KNOB FULLY COUNTER CLOCKWISE. SEE FIGURE 6. ALLOW ENGINE TO REACH THE TEMPERATURE AT WHICH YOU WANT THE FAN TO START. A GOOD STARTING POINT IS AROUND 190° F. ROTATE THERMOSTAT CONTROL KNOB CLOCKWISE UNTIL FAN ENGAGES. FAN IS NOW SET TO FUNCTION AT THE DESIRED TEMPERATURE.
5 902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 5 OF 7
6 902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 6 OF 7
18” ELECTRIC FAN KIT 32018-VUF/ 32018-VUQ
18” ELECTRIC FAN PACKING LIST No.
QTY.
1.
1 1 1 1 1 8 1 1 1 3 3 3 4 4 1 1
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
PART No. 32001-VUQ 32001-VUB 32720-VUF 40155-VUT 49457-VUI 18233-VUB 18100-VUG 40130-VUB 23100-VUW 18287-VUB 18136-VUB 18098-VUB 18250-VUB 18150-VUB 23102-VUW 23136-VUW
DESCRIPTION CHROME FAN BRACKET PLAIN FAN BRACKET FAN BLADE/ MOTOR ADJUSTABLE FAN THERMOSTAT CONTROL KNOB #6 x 3/8” PAN HEAD SCREW 1/4” COMP. MALE HALF UNION ADJ. FAN SENSOR BRACKET FUSE HARNESS 1/4” x 1/2” BOLTS 1/4” COARSE BOLT 1/4” LOCK WASHER 10/32 x 1/2” SCREW 10/32 MACHINE NUT ELECTRIC FAN WIRING HARNESS 70 AMP SINGLE SPEED FAN HARNESS
CHECKED BY: PACKED BY: DATE:
902018 REV A 1/27/11, 18” ELECTRIC FAN INSTRUCTIONS PG 7 OF 7
