3800-20310v001-082013-0-oce

Transcript

TorMinal  Operating manual 3800-20310V001-082013-0-OCE-Rev.K_GB 1 - 66 A A.2 A.3 A.4 A.1 A.5 ON W B.1 B.2 B.3 B.4  ! Please note Valid as of control unit versions: duo 500 SL, sprint 550 SL, duo 650 SL, duo vision: ver 015 marathon 550 SL, - 800 SL, - 1100 SL: ver 017 twist 200 (E): ver 031 stargilder 300: ver 012 marathon tiga 800 SL(X), - 1100 SL(X): ver 010 starglider 300 E: ver 010 gator 800N / SG1: ver 014 jive 200: ver 031 twist XL: ver 010 RDC 800, RDC vision ver 010 SP 900: S 900 ver. 015 STArter: ver. 014 duo rapido 650+ ver. 014 Settings and descriptions of earlier control unit versions are not taken into account. –3 Table of contents General Information....................................................... 6 Symbols........................................................................................................... 6 Basic safety information................................................................................... 6 Safety information for batteries........................................................................ 6 Intended use.................................................................................................... 7 Scope of supply................................................................................................ 7 Technical data.................................................................................................. 7 Display of the control unit version.................................................................... 8 Functional description................................................... 11 Operation / Use............................................................... 12 Safety instructions............................................................................................ 12 Switching on the TorMinal................................................................................ 12 Connecting to a control unit............................................................................. 12 Reading out and displaying set values............................................................ 12 Modifying and saving settings.......................................................................... 13 Resetting settings to factory settings, reset..................................................... 13 Battery change................................................................................................. 13 Explanation of terms...................................................... 14 Memory positions and their function........................... 16 sprint 550 SL, duo 500 SL / 650 SL, duo vision............................................... 16 marathon 550 SL, 800 SL, 1100 SL................................................................. 19 twist 200 (E) / DSTA24, jive 200 / DSTA24-UF,............................................... 25 starglider 300, starglider 300 E, gator 800N ................................................... 28 SG1.................................................................................................................. 32 STArter............................................................................................................. 36 ST-B-1 (SP 900; S 900)................................................................................... 38 marathon tiga 800 SL(X) / 1100 SL(X)............................................................. 44 twist XL / DT-A-1 (up to software version 1.2).................................................. 48 twist XL / DT-A-1 (as of software version 1.3) ................................................. 52 RDC 800.......................................................................................................... 56 RDC vision....................................................................................................... 58 duo rapido 650+ ............................................................................................... 60 –4  Miscellaneous................................................................. 63 Troubleshooting............................................................................................... 63 Maintenance/care............................................................................................. 63 Disposal........................................................................................................... 63 Warranty and after-sales service..................................................................... 64 Explanations/Glossary..................................................................................... 64 –5 General Information Symbols Indicates imminent danger. If not observed, serious injuries can occur For information and useful tips. A.1 (1) Refers to a respective picture in the introduction or main text. Basic safety information • The person who operates the TorMinal must have read, understood and complied with the instructions in this operating manual. • The manufacturer does not accept liability for damage or interruptions to business resulting from nonobservance of the operating manual. • Before working on a gate or a drive, always disconnect the drive from the power supply and lock it to prevent it from being switched on again. • Use the TorMinal only for the described purpose. • Never operate a damaged TorMinal. • Before operation, completely read through this operating manual and observe the safety instructions in particular. Perform the working steps in the order described in familiarize yourself with the operation. • If you make changes to the settings of a control unit, you must check the force cut-off of the drive according to the currently valid standards. • Always switch off the TorMinal after use. • Do not carry the TorMinal by the connector cable. Safety information for batteries + A B –6 General Information Intended use • Malfunctions which could affect safety must be corrected immediately. • The TorMinal may only be connected to the following drives with SOMMER control units: -- sprint 550 SL -- duo 500 SL, duo 650 SL -- marathon 550 SL, 800 SL, 1100 SL -- twist 200 (E) with control unit DSTA24 -- starglider 300 -- marathon tiga 800 SL(X), 1100 SL(X) -- starglider 300 E -- gator 400 -- jive 200 with control unit DSTA24-UF -- twist XL with control unit DT-A-1 -- twist 200 (E) with control unit DT-A-1 -- RDC 800 -- RDC vision -- STArter -- SP 900, S 900 -- duo rapido 650 • SOMMER assumes no liability for changes made to the settings of a control unit. • Modifications to the hardware and software of the TorMinal will void the warranty. • SOMMER shall assume no liability if modifications to a control unit are made with a TorMinal. • Do not store or operate the TorMinal in areas which are wet, steamy, have high air humidity, are dusty + or are subject to direct sunlight or similar conditions. Any other use does not constitute intended use. SOMMER Antriebs- und Funktechnik GmbH shall not be liable for damages resulting from this. The operator/user alone bears the soul risk. This also voids the warranty. Scope of supply 1 item TorMinal incl. 9V block battery and connection cable 1 item Operating manual 1 item Case Technical data Dimensions 120 x 65 x 22 mm Weight approx. 140 g (incl. battery and connection cable) Battery 9 V block –7 General Information Display of the control unit version Note! The correct display of the control unit version of the drive depends on the software version of the TorMinal. If the control unit version is not displayed correctly (e.g.: Test-PCB), the settings can still be modified. To update the TorMinal software, please send the TorMinal to SOMMER freight prepaid. TorMinal with software version 1.00 Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 Test PCB marathon tiga SL Test PCB starglider 300 E Test PCB gator 800N / SG1 Test PCB jive 200 DSTA24 twist XL Test PCB RDC 800 not possible RDCvision not possible Display of the second line* TorMinal with software version 1.10 and higher Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 STA24 marathon tiga SL Test PCB starglider 300 E Test PCB gator 800N / SG1 Test PCB jive 200 DSTA24 twist XL Test PCB RDC 800 not possible RDCvision not possible Display of the second line * the current version of the control unit is always displayed in the second line –8 General Information TorMinal with software version 1.20 and higher Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 STA24 marathon tiga SL tiga starglider 300 E Test PCB gator 800N / SG1 Test PCB jive 200 DSTA24 twist XL Test PCB RDC 800 not possible RDCvision not possible Display of the second line TorMinal with software version 1.30 and higher Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 STA24 marathon tiga SL tiga starglider 300 E STA1 gator 800N / SG1 STA1 jive 200 DSTA24 twist XL DT-A-1 RDC 800 not possible RDCvision not possible Display of the second line * the current version of the control unit is always displayed in the second line –9 General Information TorMinal with software version 1.40 and higher Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 STA24 marathon tiga SL tiga starglider 300 E STA1 gator 800N /SG1 STA1 jive 200 DSTA24 twist XL DT-A-1 RDC 800 RT-B-1 RDC vision RT-C-1 duo rapido 650+ Test PCP Display of the second line TorMinal with software version 1.50 and higher Operator Display of the first line sprint/duo SL Sprint marathon SL Marathon twist 200 (E) DSTA24 starglider 300 STA24 marathon tiga SL tiga starglider 300 E STA1 gator 800N / SG1 STA1 jive 200 DSTA24 twist XL DT-A-1 RDC 800 RT-B-1 RDC vision RT-C-1 SP 900 S 900 ST-B-1 STArter STA1 Display of the second line * the current version of the control unit is always displayed in the second line  – 10 Functional description A+B Component parts and their function The TorMinal is used for checking or changing set values of the SOMMER drive control units. A.1 On and off switch Switches the TorMinal ON or OFF. A.2 Display The display consists of 2 x 8 characters. The upper line shows the memory position (Mem) with its number and the lower line the associated value (Val). A.3 Connection cable A.4 Polarity protection A.5 Buttons and their function Mem + Selects the next highest memory position (e.g. from 014 to 015). Mem - Selects the next lowest memory position (e.g. from 014 to 013). This cable connects the TorMinal to the control unit. The plug has a polarity protection (PIN) to ensure that it is always connected correctly. This PIN ensures that the connection cable (A.3) is always connected to the control unit correctly. Val + Increases the value. Val - Reduces the value. Esc Cancels a changed value that has not yet been stored. Saves the set value or confirms a reset of a control unit. B.3 Battery B.4 Battery connection Power is supplied by a conventional 9 V block battery which can be purchased at the dealer or obtained from SOMMER Antriebs- und Funktechnik GmbH. Always insert the battery as shown in the graphic (B). The 9 V block battery is connected here. Check for the correct polarity (+/-)! Note! Esc and Simultaneously pressing the buttons factory settings and all changed values will be lost.  – 11 Mem + will reset control unit to Operation / Use Safety instructions Note (does not apply to the twist XL + DT-A-1)! Before every modification of a setting value, perform a control unit reset (delete force values) on the control unit (see installation and operating instructions of the respective drive). For a reset with the TorMinal, no force values are deleted but rather only the values that can be modified with the TorMinal will be reset to factory settings. The control unit must relearn the run times and required forces. Before working on a gate or a drive, always disconnect the drive from the power supply and lock it to prevent it from being switched on again. Do not touch the conductor paths of the control unit circuit board. Switching on the TorMinal A • Slide the switch (A.1) to the ON position. ÖÖ The following message appears on the display: “TorMinal Vx.x” - shows the version of the TorMinal. ÖÖ The following message appears if a button is pressed and no control unit is connected: “ !No PCB! ” ÖÖ If a control unit is connected, the control unit type, software version and control unit version is displayed. Example: marathon V017.000 . Connecting to a control unit A • Remove the control unit from the drive, see installation and operating instructions of the drive. • Connect cable (A.3) to the control unit and observe the correct polarity. The connecting cable's red lead should always point towards the control unit's coding hole. Reading out and displaying set values • The set values will be read out with the next button press the on the control panel [A.5]: -- The upper line shows the memory position (Mem). -- The lower line shows the set value (Val). ■■ “ x ” in front of the set value (Val), this value cannot be modified. ■■ “ s ” in front of the set value (Val), this value can be modified and saved.  – 12 Operation / Use Modifying and saving settings If you modify the settings the "s" in front of it goes away. This indicates that the setting was changed but not yet saved. Procedure: 1. Select the desired memory position (Mem) using the buttons Memory positions and their function. Val + 2. The set value is modified using the buttons or Mem + Val - 3. Once the desired setting has been reached, save it by pressing the or Mem - , see chapter . button 1x. ÖÖ An “s” appears in front of the value, which has now been set and saved, for confirmation. Resetting settings to factory settings, reset Note! No force values are deleted but rather only the values that can be modified with the TorMinal will be reset to factory settings. 1. Press the buttons ÖÖ Esc 2. Confirm this message with ÖÖ and Mem + simultaneously. Message: “Reset to default?” Translation: Reset to factory settings? , all values are reset to the factory settings. Message: “ALL RESET !” Translation: All settings reset! Note! If no reset is to be performed, the procedure can be cancelled by pressing the Esc  button. 3. Press a button again, message disappears. ÖÖ All values reset to factory settings. Battery change A • Switch off the TorMinal. • Remove the screw (B.1), open the battery compartment (B.2). • Remove the battery (B.3) and disconnect. • Replace the battery (B.3) with a new one of the same type. • Insert the battery (B.3), close the battery compartment (B.2). Insert the screw (B.1) and tighten it. Note! Do not pinch the battery cable. Check for the correct polarity (+/-)!  – 13 Explanation of terms The new SOMMER drives can be adjusted to nearly every gate. This image shows the velocity curve (factory setting without 2) of the drive when opening or closing a gate. 2 8 1 7 5 6 4 2 3 1. Maximum speed Highest speed of the drive - separately adjustable for opening and closing. 2. Soft running The time which the drive move with the soft running speed. Can be switched on additionally and adjusted separately: -- When the drive starts from the end positions gate CLOSE + OPEN. -- When the drive moves to the end positions gate CLOSE + OPEN. 3. Door end position OPEN Gate is open. 4. Soft running speed Lowest speed of the drive - separately adjustable for opening and closing. Note! The soft running speed must be at least 2 setting values less than the maximum speed.  – 14 Explanation of terms 5. Soft running ramp The time that the drive requires in order to reach its maximum or soft running speed. 6. Door end position CLOSED Gate is closed 7. Zero line 8. Max line Maximum settable speed. The adjustment range of the individual speeds lies between the zero line and max line. Running time The time that the drive requires in order to close or to open. Cycle counter Cycle = movement, consisting of a complete opening and closing movement between the end positions. A cycle is only counted upon reaching the end position gate closed. Backjump Serves to relieve the door and drive mechanical system. After reaching the door CLOSE end position, the drive moves in the direction of door OPEN, relieving the mechanical system.  – 15 Memory positions and their function You can read out the settings of the individual memory positions here. The first column shows the memory position, the second the possible settable range (the first number the smallest and the second number the largest possible set value), the third column describes the function and the fourth column the factory setting of the respective memory position. sprint 550 SL, duo 500 SL / 650 SL, duo vision Memory position Mem Setting range Val Functional description Factory setting = Val sprint / duo SL / duo vision 003 - 1) Learned force during gate open (OPEN) 255 3) 004 - 1) Learned force during gate close (CLOSED) 255 3) 005 - 1) Running time during gate open (OPEN) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 012 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 013 0 - 255 255 3) Partial opening time Size of the partial opening, adjustable in steps of 0.25 seconds. 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 4 larger value = longer ramp, smaller value = shorter ramp 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 16 Memory positions and their function Memory space Mem Setting range Val Functional description 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening Factory setting = Val sprint / duo SL / duo vision 25 55 4) Note! Memory position (020) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 021 0 - 40 Start of the soft running ramp for end position gate OPEN 15 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing 023 15 - 60 Maximum speed during closing 25 45 4) Note! Memory position (023) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 024 4 - 40 Start of the soft running ramp for end position gate CLOSED 15 Start of the soft running ramp before the drive move to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 028 4 - 40 Stop in end position gate CLOSED 12 Pre-warning time Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds 030 - 031 1 - 255 032 1 - 255 No function 5 Light burning time after opening the gate 175 Settable in increments of 1 second Light burning time after closing the gate Settable in increments of 1 second  – 17 175 Memory positions and their function Memory space Mem Setting range Val 033 0 - 255 Functional description Factory setting = Val sprint / duo SL / duo vision Backjump 20 Settable in increments of 1 millisecond 034 4 - 255 Reversion time 8 Duration of the reversion upon triggering of the safety input or for a force power cut-off. Settable in increments of 0.25 seconds 035 0 - 15 Switch soft running ramp on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 036 - 037 16 - 48 no function 0 48 4) Force tolerance Adjustable additional force tolerance 16 = min. additional force, 48 = max. additional force Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 047 - For testing purposes in the factory  – 18 - Memory positions and their function marathon 550 SL, 800 SL, 1100 SL Memory space Mem Setting range Val Functional description Factory setting = Val marathon SL 003 - 1) Learned force during gate open (OPEN) 255 3) 004 - 1) Learned force during gate close (CLOSED) 255 3) 005 - 1) Running time during gate open (OPEN) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 012 - 2) 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 013 0 - 255 255 3) Partial opening time Size of the partial opening, adjustable in steps of 0.25 seconds. 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 4 larger value = longer ramp, smaller value = shorter ramp 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 19 Memory positions and their function Memory space Mem Setting range Val Functional description 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening Factory setting = Val marathon SL 25 55 4) Note! Memory position (020) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 021 0 - 40 Start of the soft running ramp for end position gate OPEN 15 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing 023 15 - 60 Maximum speed during closing 25 45 4) Note! Memory position (023) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 024 4 - 40 Start of the soft running ramp for end position gate CLOSED 15 Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 026 0 - 255 Stop in end position gate CLOSED Cycle counter for maintenance 0 Specification of a set value that will trigger the maintenance message. Example: Entered set value 2: means that a maintenance must be performed after 512 cycles. If a maintenance is to be performed after an additional 512 cycles, 4 must be entered for the maintenance. 028 4 - 40 12 Pre-warning time Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds  – 20 Memory positions and their function Memory space Mem Setting range Val 030 1 - 20 Functional description Factory setting = Val marathon SL Closing time photo eyes 5 Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second 031 1 - 255 Light burning time after opening the gate 175 Settable in increments of 1 second 032 1 - 255 Light burning time after closing the gate 175 Settable in increments of 1 second (Duration of the flashing for triggered maintenance monitoring.) 033 0 - 255 Backjump 20 Settable in increments of 1 millisecond 034 4 - 255 Reversion time 8 Duration of the reversion upon triggering of the safety input or for a force power cut-off. Settable in increments of 0.25 seconds 035 0 - 15 1. Switch soft running ramps on or off 31 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 2. Relay output, mode of operation (Terminals 23 + 24) - Relay off =0 - Pulse for motor start = 16 - Status display, contact open for door open = 32 - Status display, contact closed for door open = 48 3. Service monitor If maintenance monitoring is switched on, the number of cycles to be monitored must be set at memory position 026. - Monitoring off =0 - Monitor maintenance cycles = 64 - Maintenance alarm is triggered = 128 If the maintenance alarm is triggered, the value of the memory position 035 increases by 128. Delete maintenance alarm: Reduce value of the memory position 035 by 128.  – 21 Display of the triggered maintenance monitoring Light flashes after gate CLOSED, as long as Mem 032 is set for memory position. Factory setting 175 seconds Memory positions and their function The memory position 035 has several functions (see 1 - 3), to achieve the desired setting, all values must be added up and entered. Factory setting: 1. All soft running ramps ON Value 15 2. Pulse for motor start ON Value 16 3. Maintenance monitoring OFF Value 0 result 31  – 22 Memory positions and their function Example 1: 1. All soft running ramps ON Value 15 2. Relay output Off Value 0 3. Maintenance monitoring ON Value 64 result 79 Enter this value 79 for memory position 035 and save so that all desired settings are made. Memory space Mem Setting range Val 036 0 - 31 Functional description Factory setting = Val marathon SL 0 4) Special functions 2 Note! Memory position (036) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 1. Dead-man operation only via buttons 1 + 2 Button 1 opens and button 2 always closes the gate. - off =0 - when closing (opening also possible with radio channel 1) =1 - when opening and closing =3 The memory position 036 has several functions (see 1, 2), to achieve the desired setting, all values must be added up and entered.  – 23 Memory positions and their function Memory space Mem Setting range Val 037 16 - 48 Functional description Factory setting = Val marathon SL 48 4) Force tolerance adjustable additional force tolerance 16 = min. additional force, 48 = max. additional force Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 047 - For testing purposes in the factory  – 24 - Memory positions and their function twist 200 (E) / DSTA24, jive 200 / DSTA24-UF, Memory space Mem Setting range Val 002 - 2) Functional description Factory setting = Val twist 200 (E) / DSTA24 jive 200 / DSTA24-UF 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 003 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 005 - 1) Running time door wing 2 during opening 255 3) 006 - 1) Running time door wing 2 during closing 255 3) 007 - 1) Running time door wing 1 during opening 255 3) 008 - 1) Running time door wing 1 during closing 255 3) 013 - 1) Learned-in force during opening door wing 2 255 3) 014 - 1) Learned-in force during closing door wing 2 255 3) 015 - 1) Learned-in force during opening door wing 1 255 3) 016 - 1) Learned-in force during closing door wing 1 255 3) 019 15 - 40 Soft running speed 020 50 - 110 Maximum speed 021 0 - 40 20 104 4) Motor 2: Start of the soft running ramp for the end positions 14 Start of the soft running ramp before the drive moves to the end position. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position 022 0 - 40 Stop in end position Motor 1: Start of the soft running ramp for the end positions 14 Start of the soft running ramp before the drive moves to the end position. Settable in increments of 0.25 seconds 023 4 - 16 024 5 - 255 8 - Open holding time (automatic closing) 60 Duration of the open holding time, adjustable in steps of 1 second. 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime.  – 25 Memory positions and their function 4) Perform a control unit reset, otherwise these values can be modified. Memory space Mem Setting range Val 026 1 - 40 Functional description Factory setting = Val twist 200 (E) / DSTA24 jive 200 / DSTA24-UF Pre-warning time 12 Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds 027 4 - 40 Delay time during opening door wing 1 10 Time, which door wing 1 opens after door wing 2. Settable in increments of 0.25 seconds 028 8 - 40 Delay time during closing door wing 2 20 Time, after which door wing 2 reaches the end position door CLOSED after door wing 1. Settable in increments of 0.25 seconds 030 1 - 20 Closing time photo eyes 5 Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second 031 1 - 255 Switching duration relay contact 3 Duration that the relay contact is closed after motor start. Settable in increments of 1 second 032 0 - 15 Motor 2: Switch soft running ramps on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10.  – 26 Memory positions and their function Memory space Mem Setting range Val 033 0 - 15 Functional description Factory setting = Val twist 200 (E) / DSTA24 jive 200 / DSTA24-UF Motor 1: Switch soft running ramps on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 047 - For testing purposes in the factory  – 27 - Memory positions and their function starglider 300, starglider 300 E, gator 800N Memory space Mem Setting range Val Functional description Factory setting = Val starglider 300 / 300 E, gator 800N 003 - 1) Learned force during gate open (OPEN) 255 3) 004 - 1) Learned force during gate close (CLOSED) 255 3) 005 - 1) Running time during gate open (OPEN) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 012 - 2) 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 013 0 - 255 255 3) Partial opening time Size of the partial opening, adjustable in steps of 0.25 seconds. 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 4 larger value = longer ramp, smaller value = shorter ramp 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) The value to 255 is entered on delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 28 Memory positions and their function Memory space Mem Setting range Val Functional description 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening Factory setting = Val starglider 300 / 300 E, gator 800N 27 55 4) Note! Memory position (020) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 021 0 - 40 Start of the soft running ramp for end position gate OPEN 20 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing 023 15 - 60 Maximum speed during closing 27 45 4) Note! Memory position (023) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 024 0 - 40 Start of the soft running ramp for end position gate CLOSED 20 Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 026 0 - 255 Stop in end position gate CLOSED Cycle counter for maintenance 0 Specification of a set value that will trigger the maintenance message. Example: Entered set value 2: means that a maintenance must be performed after 512 cycles. If a maintenance is to be performed after an additional 512 cycles, 4 must be entered for the maintenance. 028 4 - 40 Pre-warning time 12 Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds  – 29 Memory positions and their function Memory space Mem Setting range Val 030 1 - 20 Functional description Factory setting = Val starglider 300 / 300 E, gator 800N Closing time photo eyes 5 Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second 031 - 032 1 - 255 No function - Light burning time maintenance monitoring 175 Settable in increments of 1 second 034 4 - 255 Reversion time 2 Duration of the reversion upon triggering of the safety input or for a force power cut-off. Settable in increments of 0.25 seconds 035 0 - 255 1. Switch soft running ramps on or off 26 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 2. Relay output, mode of operation (Terminals 23 + 24) - Relay off =0 - Pulse for motor start = 16 - Status display, contact open for door open = 32 - Status display, contact closed for door open = 48 3. Service monitor If maintenance monitoring is switched on, the number of cycles to be monitored must be set at memory position 026. - Monitoring off =0 - Monitor maintenance cycles = 64 - Maintenance alarm is triggered = 128 If the maintenance alarm is triggered, the value of the memory position 035 increases by 128. Delete maintenance alarm: Reduce value of the memory position 035 by 128.  – 30 Display of the triggered maintenance monitoring Light flashes after gate CLOSED, as long as Mem 032 is set for memory position. Factory setting 175 seconds Memory positions and their function The memory position 035 has several functions (see 1 - 3), to achieve the desired setting, all values must be added up and entered. Factory setting: 1. Soft running ramps 2 + 4 ON Value 10 2. Pulse for motor start ON Value 16 3. Maintenance monitoring OFF Value 0 result 26 1. All soft running ramps ON Value 15 2. Relay output Off Value 0 3. Maintenance monitoring ON Value 64 result 79 Example 1: Enter this value 79 for memory position 035 and save so that all desired settings are made. Memory space Mem Setting range Val 036 0 - 31 Functional description Factory setting = Val starglider 300 / 300 E, gator 0 4) Special functions 2 Note! Memory position (036) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 1. Dead-man operation only via buttons 1 + 2 Button 1 opens and button 2 always closes the gate. - off - for closing (open with radio channel 1 also possible) - for opening and closing 037 16 - 48 =0 =1 =3 48 4) Force tolerance adjustable additional force tolerance 16 = min. additional force, 48 = max. additional force Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 047 - For testing purposes in the factory  – 31 - Memory positions and their function SG1 Memory space Mem Setting range Val Functional description Factory setting = Val SG1 003 - 1) Learned force during gate open (OPEN) 255 3) 004 - 1) Learned force during gate close (CLOSED) 255 3) 005 - 1) Running time during gate open (OPEN) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 012 - 2) 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 013 0 - 255 255 3) Partial opening time Size of the partial opening, adjustable in steps of 0.25 seconds. 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 6 Larger value = longer ramp, smaller value = shorter ramp 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) The value to 55 is entered on delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 32 Memory positions and their function Memory space Mem Setting range Val Functional description 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening Factory setting = Val SG1 30 43 4) Note! Memory position (020) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 021 0 - 40 Start of the soft running ramp for end position gate OPEN 30 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing 023 15 - 60 Maximum speed during closing 30 43 4) Note! Memory position (023) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 024 0 - 40 Start of the soft running ramp for end position gate CLOSED 30 Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 026 0 - 255 Stop in end position gate CLOSED Cycle counter for maintenance 0 Specification of a set value that will trigger the maintenance message. Example: Entered set value 2: means that a maintenance must be performed after 512 cycles. If a maintenance is to be performed after an additional 512 cycles, 4 must be entered for the maintenance. 028 4 - 40 Pre-warning time 12 Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds  – 33 Memory positions and their function Memory space Mem Setting range Val 030 1 - 20 Functional description Factory setting = Val SG1 Closing time photo eyes 5 Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second 031 - 032 1 - 255 No function - Light burning time maintenance monitoring 175 Settable in increments of 1 second 034 4 - 255 Reversion time 2 Duration of the reversion upon triggering of the safety input or for a force power cut-off. Settable in increments of 0.25 seconds 035 0 - 255 1. Switch soft running ramps on or off 26 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 2. Relay output, mode of operation (Terminals 23 + 24) - Relay off =0 - Pulse for motor start = 16 - Status display, contact open for door open = 32 - Status display, contact closed for door open = 48 3. Service monitor If maintenance monitoring is switched on, the number of cycles to be monitored must be set at memory position 026. - Monitoring off =0 - Monitor maintenance cycles = 64 - Maintenance alarm is triggered = 128 If the maintenance alarm is triggered, the value of the memory position 035 increases by 128. Delete maintenance alarm: Reduce value of the memory position 035 by 128.  – 34 Display of the triggered maintenance monitoring Light flashes after gate CLOSED, as long as Mem 032 is set for memory position. Factory setting 175 seconds Memory positions and their function The memory position 035 has several functions (see 1 - 3), to achieve the desired setting, all values must be added up and entered. Factory setting: 1. Soft running ramps 2 + 4 ON Value 10 2. Pulse for motor start ON Value 16 3. Maintenance monitoring OFF Value 0 result 26 1. All soft running ramps ON Value 15 2. Relay output Off Value 0 3. Maintenance monitoring ON Value 64 result 79 Example 1: Enter this value 79 for memory position 035 and save so that all desired settings are made. Memory space Mem Setting range Val 036 0 - 31 Functional description Factory setting = Val SG1 0 4) Special functions 2 Note! Memory position (036) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 1. Dead-man operation only via buttons 1 + 2 Button 1 opens and button 2 always closes the gate. - off - for closing (open with radio channel 1 also possible) - for opening and closing 037 16 - 48 =0 =1 =3 40 4) Force tolerance Adjustable additional force tolerance (in addition to the potentiometer) 16 = min. additional force, 48 = max. additional force Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 047 - For testing purposes in the factory  – 35 - Memory positions and their function STArter Memory space Mem Setting range Val Functional description Factory setting = Val STArter 003 - 1) Learned force during gate open (OPEN) Is learned 3) 004 - 1) Learned force during gate close (CLOSED) Is learned 3) 005 - 1) Running time during gate open (OPEN) Is learned 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) Is learned 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 012 - 2) Fixed value 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 Cycle counter (Z2): counts from 0 to 255 Fixed value 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 013 0 - 255 Partial opening time 255 Size of the partial opening, adjustable in steps of 0.25 seconds. 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 6 Larger value = longer ramp, smaller value = shorter ramp 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening 021 0 - 40 Start of the soft running ramp for end position gate OPEN 34 48 4) 29 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds  – 36 34 Memory positions and their function Memory space Mem Setting range Val Functional description 023 15 - 60 Maximum speed during closing 024 0 - 40 Start of the soft running ramp for end position gate CLOSED Factory setting = Val STArter 48 4) 29 Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN Stop in end position gate CLOSED 026 0 - 255 Cycle counter for maintenance 0 028 4 - 40 Prewarning time 0.25 sec. 12 030 0 - 20 Closing time photo eyes (only for automatic closing) in sec. 5 031 1 - 255 No function 032 1 - 255 Light burning time after closing the gate in sec. 034 4 - 255 Reversion time 0.25 sec. 2 035 0 - 255 Switch soft running ramp on and off, maintenance, relay outputs 26 036 0 - 31 Dead-man operation only via buttons 1 and 2 (0 = off) 8 4) 037 16 - 48 Force tolerance 40 4) 0 Adjustable additional force tolerance (in addition to the potentiometer) 16 = min. additional force, 48 = max. additional force 175 Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal 47 - For testing purposes in the factory - 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 37 Memory positions and their function ST-B-1 (SP 900; S 900) Note! A reset must be performed before changing operating parameters! Note! The DIP switch 3 must be set to so that the control units can adopt the settings from the Torminal. (For OFF, the data from the weight potentiometer are referenced) Memory space Mem Setting range Val 2 - 3 Functional description Factory setting = Val SP 900 / S 900 Maximum value of the occurring force during the opening procedure 255 3) 0-100 Force tolerance for opening procedure 25 4) 4 0-100 Maximum value for soft running opening procedure 5 - 6 0-100 Force tolerance for closing procedure 25 7 0-100 Force tolerance for soft running closing procedure 15 12 0-90 Soft running position opening procedure length (see graphic) 19 Maximum value of the occurring force during the closing procedure 15 255 3) Gate path = Path between the end switches E.g. 6 m gate running path: 600 cm / 90 = 6.6 cm increment x 19 = 25 cm soft running starting point 13 0-90 Soft running position opening procedure OFFSET (see graphic) 17 Gate running path = Path between the end switches E.g. 6m gate running path: 600 cm / 90 = 6.6 cm increment x 17 = 112 cm soft running starting point 14 0-90 Soft running position closing procedure LENGTH (see graphic) Gate running path = Path between the end switches E.g. 6 m gate running path: 600 cm / 90 = 6.6 cm increment x 19 = 125 cm soft running starting point  – 38 19 Memory positions and their function Memory space Mem Setting range Val 15 0-90 Functional description Soft running position closing procedure OFFSET (see graphic) Factory setting = Val SP 900 / S 900 17 Gate running path = Path between the end switches E.g. 6 m gate running path: 600 cm / 90 = 6.6 cm increment x 17 = 112 cm soft running starting point 16 26-255 Soft running speed during opening 17 26-255 Soft running speed during closing 63 18 26-255 Maximum speed during opening 115 19 26-255 Maximum speed during closing 115 Memory space Mem Setting range Val 20 - Functional description Cycle counter LowByte 63 Factory setting = Val SP 900 / S 900 0 Cycle counter Highbyte x 256 + Cycle counter LowByte = Total cycle count 21 - Cycle counter HighByte 0 Cycle counter Highbyte x 256 + Cycle counter LowByte = Total cycle count 22 10-100 Reversion time for force power cut-off or safety contact strip for OPEN in 10 ms increments 50 ATTENTION: The modification of the reversion times needs to occur if, for example, a gate with bars makes this necessary! 23 10-100 Reversion time for force power cut-off or safety contact strip for CLOSE in 10 ms increments 50 ATTENTION: The modification of the reversion times needs to occur if, for example, a gate with bars makes this necessary! 25 10-255 Photo eyes reversion time in 16 ms increments 250 ATTENTION: The modification of the reversion times needs to occur if, for example, a gate with bars makes this necessary! 26 78-255 The time after which it will be closed early if the photo eyes are passed through PROVIDED DIP 6 is activated (= ON) in 64 ms increments.  – 39 78 Memory positions and their function Memory space Mem Setting range Val 27 0-200 Functional description Factory setting = Val SP 900 / S 900 0 Open hold time If the open holding time in this memory cell is NOT EQUAL to 0, then the value from the Torminal is used. Otherwise the value set on the potentiometer applies To differentiate whether fully automatic or half automatic Auto closing, a determination can be made by means of the SFLAG1 register. However, this determination only applies if Mem 27 is NOT EQUAL to 0. Bear in mind that this memory cell works like an activated auto close (if partial opening is required), the partial opening must initially be learned in before this cell can be set to a value - otherwise the partial opening will not function. If this is the case: set this cell = 0, learn in partial opening and then set the cell to 1 again. Also observe if a customer version is learned in! The problem is then that a preset partial opening width also must be in the Torminal 33 0-30 Partial opening width 30 E.g. 6 m gate running path: 600 cm / 90 = 6.6 cm increment per Torminal increment 34 0-42 Release delay for solenoid for stop 8 (Jamming protection of the locking bolt) in 64 ms sec. increments 35 0-250 Pre-warning time for opening adjustable in 0.25 second increments 20 36 0-255 Pre-warning time for closing adjustable in 0.25 second increments 20  – 40 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val SP 900 / S 900 37 0-255 Special functions: VALUE =1 for soft stop on button press or photo eyes event active Value = O for deactivated VALUE = 2 for flashing during gate running (factory state) VALUE = 0 for lit up during gate running VALUE = 4 for sliding gate released a mechanics in CLOSED by means of a 6 ms backjump VALUE = 8 for half-automatic operation active (independently of potentiometer setting if for open holding time != 0 is set) VALUE = 0 for Fully automatic operation active (independent of potentiometer setting) VALUE = 16 for automatic closing off OPENED active/VALUE = 0 for deactivated VALUE = 32 for automatic closing off PARTIAL OPENING active/ VALUE = 0 deactivated VALUE = 64 for solenoid deactivated / VALUE = 0 for solenoid present 59 Factory setting: The memory position 037 has several functions; in order to achieve the desired settings, all values must be added together and entered Factory setting: VALUE =1 for soft stop on button press or photo eyes event active Value = O for deactivated VALUE = 2 for flashing during gate running (factory state) VALUE = 0 for lit up during gate running VALUE = 8 for half-automatic operation active (independently of potentiometer setting if for open holding time != 0 is set) VALUE = 0 for fully automatic operation active (independent of potentiometer setting) VALUE = 16 for automatic closing off OPENED active/VALUE = 0 for deactivated = VALUE = 32 for automatic closing off PARTIAL OPENING active/ VALUE = 0 deactivated 39 0-255 Multi-function relay programming VALUE = 0 = off VALUE = 1 = Function as gate status display (relay activated as long as drive not closed in end position, CLOSED=deactivated) VALUE =2 = Radio channel 4 -> Inching mode relay contact (defined opening and closing via radio is omitted) VALUE =3 = Radio channel 4 -> Toggle mode relay contact (defined opening and closing via radio is omitted) e.g. outside light VALUE =4 = Relay activated as long as drive stays in the GATE OPEN VALUE =5 = Relay activated as long as drive stays in the GATE CLOSE VALUE =6 = Relay activated as long as drive running (excluding prewarning phase) VALUE =7 = Relay cycles during drive running (excluding pre-warning phase) VALUE =8 = Relay activated as long as drive running (including prewarning phase) VALUE =9 = Relay cycles during drive running (including pre-warning phase) Please enter the corresponding value and save for the desired function.  – 41 0 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val SP 900 / S 900 40 - Last error to occur is stored in the faulty memory and output again. VALUE = 1 = Safety contact strip actuated in OPEN direction VALUE = 2 = Wireless safety contact strip actuated in OPEN direction VALUE = 3 = Safety contact strip actuated in CLOSE direction VALUE = 4 = Wireless safety contact strip actuated in CLOSE direction VALUE = 5 = Force cut-off during soft running when closing VALUE = 6 = Force cut-off during opening VALUE = 7 = Force cut-off during soft running when opening VALUE = 8 = Force cut-off during closing VALUE = 9 = Motor ENcoder error VALUE = 10= Gate running path over 8 metres VALUE = 11= Running time or running path exceeded VALUE = 14= Drive has been overloaded during the movement VALUE = 22= Motor blocking protection has activated VALUE = 23= Drive has been overloaded during the movement VALUE = 28= End switch error both end switches were simultaneously active VALUE = 42= Battery charge state critical (<20%) VALUE = 50= Obstacle in CLOSE direction during start of a reversion procedure in OPEN VALUE = 51= Obstacle in CLOSE direction during start of a reversion procedure in CLOSE VALUE = 52= No strip for the CLOSE direction could be found during the self test of the wireless safety contact strip (goes along with system error) VALUE = 53= No strip for the OPEN direction could be found during the self test of the wireless safety contact strip (goes along with system error) VALUE = 54 = Error of the wireless safety contact strip during self test module plugged in, however, defective or safety contact strips blocked or battery flat 0 41 0-255 Time until switching into standby mode in 2 second increments Maximum time approx. 255 * 2 sec. IF VALUE OPEN "0" is set, the standby is deactivated (also possible by means of compiler switch) 200 42 - Delay time during test procedure of the photo eyes in 10 ms increments 10 43 - Delay time during test procedure of the safety contact strips in 10 ms increments 10 44 - Wireless safety contact strip VALUE = 0 Master module was not detected VALUE = 1 Master module was detected ATTENTION: The master module is only detected during the learning run. To add a module later, the force values must be deleted and the module then plugged in so that the system considers this as valid module. 0 45 - Detected photo eyes type VALUE = 2 = 2-wire photo eye VALUE = 4 = 4-wire photo eye ATTENTION: Photo eyes are only detected during the learning run. To change to a different photo eyes type later, the force values must be deleted and the new photo eye then connected so that the system considers this as valid. 4  – 42 Memory positions and their function Memory space Mem Setting range Val Functional description 46 - Detected safety contact strip for opening procedure VALUE = 0 = No safety contact equipment detected VALUE = 8= 8K2 strip detected VALUE = 16 = OSE detected ATTENTION: Strips are only detected during the learning run. To add additional strips later 8 47 - Detected safety contact strip for closing procedure VALUE = 0 = No safety contact equipment detected VALUE = 8= 8K2 strip detected VALUE = 16 = OSE detected ATTENTION: Strips are only detected during the learning run. To add additional strips later 8 Endlage AUF Soft close offset "MEM 15" Soft open offset "MEM 13" Speed open "MEM18" Soft running speed open "MEM16" Soft running speed close "MEM17" Speed close "MEM19" Endlage ZU Soft close length "MEM 14" Factory setting = Val SP 900 / S 900 Soft open length "MEM 12" 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 43 Memory positions and their function marathon tiga 800 SL(X) / 1100 SL(X) Memory space Mem Setting range Val Functional description Factory setting = Val marathon tiga SL(X) 003 - 1) Learned force during gate open (OPEN) 255 3) 004 - 1) Learned force during gate close (CLOSED) 255 3) 005 - 1) Running time during gate open (OPEN) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 006 - 1) Running time during gate close (CLOSED) 255 3) Value in steps of 0.25 seconds Example: displayed value 40 = 10 seconds 011 - 2) 012 - 2) 013 - 2) 255 3) Cycle counter (Z0) Number of cycles: Counter reading times 65,536 255 3) Cycle counter (Z1) Number of cycles: Counter reading times 256 Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: Z0 × 16,536 + Z1 × 256 + Z2 = Number of cycles 017 0 - 255 Length of soft running from the end position gate OPEN or gate CLOSED 0 Up to accelerations to maximum speed. 0 - no soft running, 255 - max. length Soft running length Door end position CLOSED Door end position OPEN 018 0-8 Length of the soft running ramp 4 Larger value = longer ramp, smaller value = shorter ramp 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 44 Memory positions and their function Memory space Mem Setting range Val Functional description 019 15 - 60 Soft running speed during opening 020 15 - 60 Maximum speed during opening Factory setting = Val marathon tiga SL(X) 25 55 4) Note! Memory position (020) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 021 0 - 40 Start of the soft running ramp for end position gate OPEN 15 Start of the soft running ramp before the drive move to the end position gate OPEN. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 022 15 - 60 Soft running speed during closing 023 15 - 60 Maximum speed during closing 25 45 4) Note! Memory position (023) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 024 0 - 40 Start of the soft running ramp for end position gate CLOSED 15 Start of the soft running ramp before the drive moves to the end position gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 026 0 - 255 Stop in end position gate CLOSED Cycle counter for maintenance 0 Specification of a set value that will trigger the maintenance message. Example: Entered set value 2: means that a maintenance must be performed after 512 cycles. If a maintenance is to be performed after an additional 512 cycles, 4 must be entered for the maintenance. 027 0 - 255 Pre-warning time OPEN Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds  – 45 16 Memory positions and their function Memory space Mem Setting range Val 028 0 - 255 Functional description Pre-warning time CLOSE Factory setting = Val marathon tiga SL(X) 20 Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds 030 1 - 20 Closing time photo eyes or extension of the open hold time 5 Depending on the setting of DIP switch 4 or 5, whereby DIP switch 4 has priority: DIP 4 OFF: Open hold time proceeds normally. DIP 4 ON: Close gate after X seconds after driving through the photo eyes. DIP 5 OFF: Open hold time proceeds normally. DIP 5 ON: After driving through the photo eyes, extend the open old time by x seconds. Settable in increments of 1 second 031 2 - 255 Open hold time 30 Settable in increments of 1 second 032 0 - 255 Clearing time 40 Settable in increments of 0.25 seconds 033 0 - 255 Backjump 20 Settable in increments of 1 millisecond 034 4 - 255 Reversion time 8 Duration of the reversion upon triggering of the safety input or for a force power cut-off. Settable in increments of 0.25 seconds  – 46 Memory positions and their function Memory space Mem Setting range Val 035 0 - 255 Functional description Factory setting = Val marathon tiga SL(X) 1. Switch soft running ramps on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 3. Service monitor If maintenance monitoring is switched on, the number of cycles to be monitored must be set at memory position 026. - Monitoring off =0 - Monitor maintenance cycles = 64 - Maintenance alarm is triggered = 128 If the maintenance alarm is triggered, the value of the memory position 035 increases by 128. Delete maintenance alarm: Reduce value of the memory position 035 by 128. 037 16 - 60 48 4) Force tolerance Adjustable additional force tolerance 16 = min. additional force, 60 = max. additional force Note! Memory position (037) can only be modified after previous control unit reset (delete force). This control unit reset cannot be performed with the TorMinal. 047 - For testing purposes in the factory  – 47 - Memory positions and their function twist XL / DT-A-1 (up to software version 1.2) Memory space Mem Setting range Val Functional description Factory setting = Val twist XL / DT-A-1 003 - 1) Learned-in force during opening door wing 2 255 3) 004 - 1) Learned-in force during closing door wing 2 255 3) 005 - 1) Learned-in force during opening door wing 1 255 3) 006 - 1) Learned-in force during closing door wing 1 255 3) 007 - 1) Running time door wing 2 during opening 255 3) 008 - 1) Running time door wing 2 during closing 255 3) 009 - 1) Running time door wing 1 during opening 255 3) 010 - 1) Running time door wing 1 during closing 255 3) 012 - 2) Cycle counter (Z1) 255 3) Number of cycles: Counter reading times 256 013 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of the total cycles Z1 x 256 +Z2 014 0-7 Warning light, dead-man operation, force cutoff 2 1 VALUE = 0 = Warning light lights up during a gate movement VALUE = 1 = Warning light flashes during a gate movement VALUE = 2 = Dead man operation VALUE = 4 = Force cut-off (1 -> 2) switchover: more sensitive activation for smaller B dimensions and smooth-running gates. Example: Warning light is to flash (1) + Force cut-off 2 (4): 1 + 4 = 5, enter and save this value 5. 016 8 - 40 12 Pre-warning time Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds Memory space Mem Setting range Val 020 8 - 40 Functional description Delay time during closing door wing 2 Factory setting = Val twist XL / DT-A-1 27 Time, after which door wing 2 reaches the end position door CLOSED after door wing 1. Settable in increments of 0.25 seconds 021 1 - 20 Closing time photo eyes Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second  – 48 5 Memory positions and their function Memory space Mem Setting range Val 022 1 - 255 Functional description Switching duration relay contact Factory setting = Val twist XL / DT-A-1 3 Duration that the relay contact is closed after motor start. Settable in increments of 1 second 023 4 - 40 Delay time during opening door wing 1 12 Time, which door wing 1 opens after door wing 2. Settable in increments of 0.25 seconds 024 0-8 Length of the soft running ramp 4 Larger value = longer ramp, smaller value = shorter ramp 025 15 - 60 Soft running speed for gate OPEN (M2) 27 3) 026 15 - 60 Maximum speed for gate OPEN (M2) 55 3) 027 0 - 40 Start of the soft running ramp for end position gate OPEN (M2) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 028 15 - 60 Soft running speed for gate CLOSE (M2) 27 3) 029 15 - 60 Maximum speed for gate CLOSE (M2) 45 3) 030 0 - 40 Start of the soft running ramp for end position gate CLOSED (M2) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate CLOSED Start from end position gate OPEN 031 15 - 60 Soft running speed for gate OPEN (M1) 27 3) 032 15 - 60 Maximum speed for gate OPEN (M1) 55 3) 033 0 - 40 Start of the soft running ramp for end position gate OPEN (M1) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED  – 49 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val twist XL / DT-A-1 034 15 - 60 Soft running speed for gate CLOSE (M1) 27 3) 035 15 - 60 Maximum speed for gate CLOSE (M1) 45 3) 036 0 - 40 Start of the soft running ramp for end position gate CLOSED (M1) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate CLOSED Start from end position gate OPEN 037 10 - 255 30 3) Force tolerance, gate wing 2 (M2) Adjustable additional force tolerance 10 = min. additional force, 255 = max. additional force 038 10 - 255 30 3) Force tolerance, gate wing 2 (M1) Adjustable additional force tolerance 10 = min. additional force, 255 = max. additional force 039 0 - 15 Soft running ramps, gate wing 2 (M2) switch on or off This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10.  – 50 15 Memory positions and their function Memory space Mem Setting range Val 040 0 - 15 Functional description Factory setting = Val twist XL / DT-A-1 Soft running ramps, gate wing 1 (M1) switch on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 042 0-8 Afterrun for gate CLOSE (M2) 0 After reaching the gate CLOSED end position, the drive continues to run in order to close the gate cleanly (gate wings are braced with each other by this). Settable in increments of 0.25 seconds 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 51 Memory positions and their function twist XL / DT-A-1 (as of software version 1.3) Memory space Mem Setting range Val Functional description Factory setting = Val twist XL / DT-A-1 003 - 1) Learned-in force during opening door wing 2 255 3) 004 - 1) Learned-in force during closing door wing 2 255 3) 005 - 1) Learned-in force during opening door wing 1 255 3) 006 - 1) Learned-in force during closing door wing 1 255 3) 007 - 1) Running time door wing 2 during opening 255 3) 008 - 1) Running time door wing 2 during closing 255 3) 009 - 1) Running time door wing 1 during opening 255 3) 010 - 1) Running time door wing 1 during closing 255 3) 012 - 2) Cycle counter (Z1) 255 3) Number of cycles: Counter reading times 256 013 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of total cycles warning light 014 0 - 15 Warning light, dead-man operation, force cutoff 2 1 VALUE = 0 = Warning light lights up during a gate movement VALUE = 1 = Warning light flashes during a gate movement VALUE = 2 = Dead man operation VALUE = 4 = Force cut-off (1 -> 2) switchover: more sensitive activation for smaller B dimensions and smooth-running gates. VALUE = 8 = Cancel write protection Example: Warning light is to flash (1) + Force cut-off 2 (4): 1 + 4 = 5, enter and save this value 5. 016 8 - 40 Pre-warning time 12 Duration of the pre-warning time, adjustable in steps of 0.25 seconds. 4 = 1 seconds, 40 = 10 seconds  – 52 Memory positions and their function Memory space Mem Setting range Val 020 8 - 40 Functional description Delay time during closing door wing 2 Factory setting = Val twist XL / DT-A-1 27 Time, after which door wing 2 reaches the end position door CLOSED after door wing 1. Settable in increments of 0.25 seconds 021 1 - 20 Closing time photo eyes 5 Duration of the open hold time, after driving through the photo eyes, only in conjunction with automatic closing function. Settable in increments of 1 second 022 1 - 255 Switching duration relay contact 3 Duration that the relay contact is closed after motor start. Settable in increments of 1 second 023 4 - 40 Delay time during opening door wing 1 12 Time, which door wing 1 opens after door wing 2. Settable in increments of 0.25 seconds 024 0-8 Length of the soft running ramp 4 Larger value = longer ramp, smaller value = shorter ramp 025 15 - 60 Soft running speed for gate OPEN (M2) 27 3) 5) 026 15 - 60 Maximum speed for gate OPEN (M2) 46 3) 5) 027 0 - 40 Start of the soft running ramp for end position gate OPEN (M2) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate OPEN Start from end position gate CLOSED 028 15 - 60 Soft running speed for gate CLOSE (M2) 27 3) 5) 029 15 - 60 Maximum speed for gate CLOSE (M2) 42 3) 5) 030 0 - 40 Start of the soft running ramp for end position gate CLOSED (M2) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Stop in end position gate CLOSED Start from end position gate OPEN 031 15 - 60 Soft running speed for gate OPEN (M1) 27 3) 5) 032 15 - 60 Maximum speed for gate OPEN (M1) 46 3) 5)  – 53 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val twist XL / DT-A-1 033 0 - 40 Start of the soft running ramp for end position gate OPEN (M1) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate CLOSED Stop in end position gate OPEN 034 15 - 60 Soft running speed for gate CLOSE (M1) 27 3) 5) 035 15 - 60 Maximum speed for gate CLOSE (M1) 42 3) 5) 036 0 - 40 Start of the soft running ramp for end position gate CLOSED (M1) 15 3) Start of the soft running ramp before the drive moves to the end position gate OPEN or gate CLOSED. Settable in increments of 0.25 seconds Begin soft running ramp Start from end position gate OPEN 037 10 - 255 Stop in end position gate CLOSED 37 3) 5) Force tolerance, gate wing 2 (M2) Adjustable additional force tolerance 10 = min. additional force, 255 = max. additional force 038 10 - 255 37 3) 5) Force tolerance, gate wing 2 (M1) Adjustable additional force tolerance 10 = min. additional force, 255 = max. additional force 039 0 - 15 Soft running ramps, gate wing 2 (M2) switch on or off This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10.  – 54 15 Memory positions and their function Memory space Mem Setting range Val 040 0 - 15 Functional description Factory setting = Val twist XL / DT-A-1 Soft running ramps, gate wing 1 (M1) switch on or off 15 This function allows you to switch the soft running ramps on or off individually. All soft running ramps (1 - 4) switched on = 15 Ramp 1 (Start from end position gate CLOSED) ON = 1 Ramp 2 (Stop in end position gate OPEN) ON =2 Ramp 3 (Start from end position gate OPEN) ON =4 Ramp 4 (Stop in end position gate CLOSED) ON =8 Set and save desired values. Example 1: Switch off Ramp 1+ Ramp 2: 15 - 1 - 2 = 12, enter and save this value 12. Example 2: Switch on Ramp 2+ Ramp 4: 2 + 8 = 10, enter and save this value 10. 042 0-8 Afterrun for gate CLOSE (M2) 0 After reaching the gate CLOSED end position, the drive continues to run in order to close the gate cleanly (gate wings are braced with each other by this). Settable in increments of 0.25 seconds 44 5-255 Open holding time in half-automatic closing 60 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified. 5) Cancel write protection: Add Mem 14 + 8 (If the write protection is activated again, the control unit reverts to the potentiometer settings. The values set with the Torminal will be lost) * By cancelling the write protection, the following values can be modified  – 55 Memory positions and their function RDC 800 Memory space Mem Setting range Val 002 - 1) Functional description Running time during gate open (OPEN) Factory setting = Val RDC 800 255 3) Value in increments of 1 second. Example: Displayed value 40 equals 40 seconds 003 - 1) Running time during gate open (CLOSED) 255 3) Value in increments of 1 second. Example: Displayed value 40 equals 40 seconds 004 0 - 128 Partial opening time 0 Size of the partial opening, adjustable in increments of 1 second. 005 2 - 10 007 - 2) Offset for learned running time gate OPEN and CLOSE for runtime monitoring 2 Settable in increments of 1 second Cycle counter (Z1) 255 3) Number of cycles: Counter reading times 256 008 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 010 - 2) Automatic detection of the safety contact strip type 0 128 = Fraba System detected 16 = 8.2 kOhm detected 011 0 - 255 Setup time for photo eyes during self test. 85 Settable in increments of 8 milliseconds. 013 0 - 255 017 60 - 255 Open hold time for automatic closing via pulse button (DIP 5 ON) 20 Settable in increments of 1 second Start-up suppression 180 Time settable in increments of 8 milliseconds. 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 56 Memory positions and their function Memory space Mem Setting range Val 018 4 - 12 019 0-1 Functional description Maximum delay up to the activation of the safety contact strip after activation of the prelimit switch. Factory setting = Val RDC 800 8 n x 256 milliseconds Test safety contact strip active 1 After activating the pre-limit switch, the safety contact strip must be triggered. 0 = Test OFF, 1 = Test ON 047 - For testing purposes in the factory  – 57 - Memory positions and their function RDC vision Memory space Mem Setting range Val 002 - 1) Functional description Running time during gate open (OPEN) Factory setting = Val RDC vision 255 3) Value in increments of 1 second. Example: Displayed value 40 equals 40 seconds 003 - 1) Running time during gate open (CLOSED) 255 3) Value in increments of 1 second. Example: Displayed value 40 equals 40 seconds 004 0 - 128 Partial opening time 0 Size of the partial opening, adjustable in increments of 1 second. 005 2 - 10 007 - 2) Offset for learned running time gate OPEN and CLOSE for runtime monitoring 2 Settable in increments of 1 second Cycle counter (Z1) 255 3) Number of cycles: Counter reading times 256 008 - 2) Cycle counter (Z2): counts from 0 to 255 255 3) Number of completed cycles: Z1 x 256 + Z2 Example: 3 x 256 + 77 = 845 010 - 2) Automatic detection of the safety contact strip type 0 VALUE = 128 = Fraba System detected VALUE = 16 = 8.2 kOhm detected 011 0 - 255 Setup time for photo eyes during self test. 85 Settable in increments of 8 milliseconds. 012 0-8 Relay output (mode of operation) 1 VAULE = 0 = Pulse for motor start, pulse duration 1 second (NO contact closed, NC contact opened) VALUE = 1 = Timer output (NO contact closed, NC contact opened) Gate OPEN: Duration of adjustable with MEM 014 Gate CLOSED: Duration adjustable with MEM 015 Gate status display at end position VALUE = 2 = Gate CLOSED, NO contact closed VALUE = 4 = Gate CLOSED, NC contact closed VALUE = 8 = Gate OPEN, NO contact opened 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 58 Memory positions and their function Memory space Mem Setting range Val 013 0 - 255 Functional description Open hold time for automatic closing via pulse button (DIP 5 ON) Factory setting = Val RDC vision 20 Settable in increments of 1 second 014 0 - 255 Light burning time after opening the gate 120 Settable in increments of 1 second 015 0 - 255 Light burning time after closing the gate 120 Settable in increments of 1 second 016 0 - 255 Light burning time manual 60 Settable in increments of 1 second 017 60 - 255 Start-up suppression 180 Time settable in increments of 8 milliseconds. 018 4 - 12 019 0-1 Maximum delay up to the activation of the safety contact strip after activation of the prelimit switch. 8 n x 256 milliseconds Test safety contact strip active 1 After activating the pre-limit switch, the safety contact strip must be triggered. VALUE = 0 = Test OFF, 1 = Test ON 047 - For testing purposes in the factory  – 59 - Memory positions and their function duo rapido 650+ Note! A reset must be performed before changing operating parameters! Memory space Mem Setting range Val Functional description 2 - 3 10-50 Force tolerance for opening procedure 35 4 10-50 Force tolerance for soft running opening procedure 35 5 - 6 10-50 Force tolerance for closing procedure 35 7 10-50 Force tolerance for soft running closing procedure 15 Maximum value of the occurring force during the opening procedure Maximum value of the occurring force during the closing procedure Set speed for start Factory setting = Val duo rapido 650+ 2553) 2553) 9 26-255 10 0-255 Time specification for soft start ramp during closing in ms increments 150 11 0-255 Time specification for soft start ramp during opening in 16 ms increments 150 12 0-80 Soft running starting position opening procedure LENGTH (see graphic) 35 15 Gate running path = Path between the end switches E.g. 2.4 m gate running path: 240 cm / 80 = 3 cm increment x 15 = 45 cm soft running starting point 13 0-80 Soft running position opening procedure OFFSET (see graphic) 7 Gate running path = Path between the end switches E.g. 2.4m gate running path: 240 cm / 80 = 3 cm increment x 7 = 21 cm soft running starting point 14 0-80 Soft running position closing procedure LENGTH (see graphic) 7 Gate running path = Path between the end switches E.g. 2.4 m gate running path: 240 cm / 80 = 3 cm increment x 7 = 21 cm soft running starting point 15 0-80 Soft running position closing procedure OFFSET (see graphic) Gate running path = Path between the end switches E.g. 2.4 m gate running path: 240 cm / 80 = 3 cm increment x 3 = 9 cm running starting point  – 60 3 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val duo rapido 650+ 16 25-255 Speed specification for the drive during soft running open 40 17 25-255 Speed specification for the drive during soft running close 30 18 25-255 Speed specification for the drive during the opening 120 19 25-255 Speed specification for the drive during the closing 55 20 - Cycle counter LowByte 0 Cycle counter Highbyte x 256 + Cycle counter LowByte = Total cycle count 21 - Cycle counter HighByte 0 Cycle counter Highbyte x 256 + Cycle counter LowByte = Total cycle count 22 10-100 Reversion time for force cut-off for OPEN in 10 ms increments 100 23 10-100 Reversion time for force cut-off for CLOSE in 10 ms increments 100 24 0-255 Switch-on duration of the int. lighting after move to gate "OPEN" in 1s increments 175 25 0-255 Switch-on duration of the int. lighting after move to gate "CLOSED" and "Power ON" in 1s increments 175 26 100-255 Photo eyes reversion time in 16 ms increments 150 27 78-255 The time after which it will be closed early if the photo eyes are passed through in 64 ms increments. 78 Requirement for the correct functioning: Parameter 37: "5 seconds after photo eyes event close" is activated 28 0-200 Open hold time for automatic closing 0 Pattern 1 second. To differentiate whether fully automatic or half automatic auto closing, a determination can be made by means of parameter 37. 32 40-100 33 0-80 Speed specification "slow movement" e.g. during the learning movement or after a force cut-off 40 Partial opening width 10 e.g.: 2.4 m gate running path: 240 cm / 80 = 3 cm increment per Torminal increment 35 0-255 Pre-warning time for opening adjustable in 0.25 second increments  – 61 12 Memory positions and their function Memory space Mem Setting range Val Functional description Factory setting = Val duo rapido 650+ 36 0-255 Pre-warning time for closing adjustable in 0.25 second increments 12 37 0-58 Special functions automatic closing 58 VALUE = 2: 1 = 5 seconds after photo eyes event close. VALUE = 8: 1 = Half automatic operation active/fully automatic closing deactivated. VALUE = 16: 1 = Automatic closing off OPENED active. VALUE = 32: 1 = Automatic closing off PARTIAL OPENING active. 38 0-3 Special functions 3 39 0-255 Special functions 0 40 - Last occurring error in the fault memory 0 VALUE = 5 = Force cut-off soft running close VALUE = 6 = Force-off normal movement close VALUE = 7 = Force cut-off soft running open VALUE =8 = Force cut-off normal movement open 41 100-230 Special function 190 42 10-255 Delay time T from power up of the photo eyes up to the detection attempt in 10 ms increments 10 43 10-255 Special function 60 45 - Detected photo eyes type 4 VALUE = 2 = 2-wire photo eye VALUE = 4 = 4-wire photo eye ATTENTION: Photo eyes are only detected during the learning run. In order to change a different photo eyes type retroactively, the force values must be deleted and the new photo eyes then connected so that the system considers it as valid. 1) Displayed value cannot be modified, is read in and saved by the control during learning in of the forces and runtimes. 2) Display value cannot be modified. 3) Value is entered at delivery. The actual required values are saved after learning in the forces and runtime. 4) Perform a control unit reset, otherwise these values can be modified.  – 62 Miscellaneous Troubleshooting Malfunction/behaviour Cause/message on the display Possible remedies -- No display -- TorMinal switched off -- Displayed effective - TorMinal was dropped -- Battery flat -- Display black Information in the display -- ! No PCB ! -- Switch on the TorMinal -- Replace TorMinal -- Replace battery -- Connection cable plugged in incorrectly -- No control unit connected -- Connection cable (A.3) defective Set value cannot be modified -- An “x” appears in front of it -- Factory setting cannot be modified Reset the setting to factory setting -- An "s" appears in front of it -- The modified value not saved -- RESET performed, all values reset to the factory setting Maintenance/care If needed, the housing can be wiped off with a moist cloth. Use warm water with a small amount of washing-up liquid or a plastic cleaner. Disposal -- Please note There is a risk of fire or acid burns for improper handling. Do not burn batteries, take them apart or damage them. -- Do not subject batteries to temperatures higher than 60 C. Do not subject batteries to direct sunlight or extreme humidity. -- Keep batteries out of the reach of children. If the battery is accidentally swallowed, seek immediate medical attention. -- When storing or disposing of batteries always pack them using tape so that they will not come into contact with other metal objects. They could ignite or cause damage. -- Do not dispose of batteries or the TorMinal in the regular household waste. -- Damaged or used batteries must be properly disposed of immediately. Contact your local environmental authority or your waste disposal representative.  – 63 Miscellaneous Warranty and after-sales service The guarantee complies with the legal regulations. Contact your specialist dealer if there are any guarantee issues. The warranty applies only for the country in which the TorMinal was purchased. Batteries, fuses and bulbs are excluded from the warranty. Please contact your dealer if you require customer service, replacement parts or accessories. We have attempted to make this operating manual as clear as possible. If you have feedback which could help us improve it or there are missing specifications in the operating manual, please send us your suggestions: Fax.: 0049 / 7021 / 8001 - 403 email: [email protected] Explanations/Glossary Item no. Name Article no. Amount Explanation Battery 46005 1 Used for the power supply of the TorMinal. Connection cable Connects control unit and TorMinal. MEM Memory space VAL Set value  – 64 SOMMER Antriebs- und Funktechnik GmbH Hans-Böckler-Straße 21-27 73230 Kirchheim/Teck Tel.: +49 7021 8001-0 Fax.: +49 7021 8001-100 [email protected] www.sommer.eu © Copyright 2012 All rights reserved