39t6195

Transcript

ThinkPad Computer Hardware Maintenance Manual January 2006 This manual supports: ThinkPad Z60m (MT 2529, 2530, 2531, 2532) Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 175. First Edition (January 2006) © Copyright Lenovo 2006. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in Data-General, FAR 52.227.14 (Alternate III). Contents About this manual . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . 3 Important service information . . . . . . . . . 3 Strategy for replacing FRUs . . . . . . . . . 3 Strategy for replacing a hard disk drive . . . . . 4 Important notice for replacing a system board . . . 4 How to use error messages . . . . . . . . 4 Strategy for replacing FRUs for CTO, CMV, and GAV 4 Product definition . . . . . . . . . . . 4 FRU identification for CTO, CMV, and GAV products 5 Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . . . . 7 Diskette compatibility matrix . . . . . . . . . 8 Safety notices: multilingual translations . . . . . . 8 Safety information . . . . . . . . . . . . 20 General safety . . . . . . . . . . . . 20 Electrical safety . . . . . . . . . . . 21 Safety inspection guide . . . . . . . . . 23 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . 24 Grounding requirements . . . . . . . . . 25 Laser compliance statement . . . . . . . . . 26 General descriptions . . . . . . . . Read this first . . . . . . . . . . . What to do first . . . . . . . . . Related service information . . . . . . . Service Web site . . . . . . . . . Restoring the pre-installed system . . . . Passwords . . . . . . . . . . . Power management . . . . . . . . Checkout guide . . . . . . . . . . Testing the computer . . . . . . . . Detecting system information with PC-Doctor . Power system checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 29 29 31 31 31 32 35 37 37 40 41 ThinkPad Z60m . . . Product overview . . . Specifications . . . Status indicators . . FRU tests . . . . Fn key combinations . Symptom-to-FRU index . Numeric error codes . Error messages . . Beep symptoms . . No-beep symptoms . LCD-related symptoms Intermittent problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 47 47 50 53 55 58 58 63 65 65 66 67 © Copyright Lenovo 2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Undetermined problems . . . . . . . . . 67 FRU replacement notices . . . . . . . . . 68 Screw notices . . . . . . . . . . . . 68 Retaining serial numbers. . . . . . . . . 69 Removing and replacing a FRU. . . . . . . . 72 1010 Battery pack. . . . . . . . . . . 73 1020 Ultrabay Enhanced device . . . . . . 75 1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails . . . . . . . 76 1040 Palm rest or palm rest with fingerprint reader 79 1050 DIMM . . . . . . . . . . . . 81 1060 Keyboard . . . . . . . . . . . 82 1070 Mini PCI adapter for wireless LAN . . . . 84 1080 Modem daughter card (MDC-1.5) . . . . 85 1090 PCI Express Mini card for wireless WAN 87 1100 Backup battery . . . . . . . . . . 89 1110 Wireless WAN antenna cable (DIV) . . . . 90 1120 Keyboard bezel and speaker assembly . . . 92 1130 Fan assembly . . . . . . . . . . 95 1140 CPU . . . . . . . . . . . . . 99 1150 LCD assembly . . . . . . . . . . 100 1160 Base cover . . . . . . . . . . . 103 1170 3-1 Digital Media Reader sub card with cable 106 1180 USB sub card with cable . . . . . . . 108 1190 MG (magnesium) frame . . . . . . . 110 1200 System board and PC Card/ExpressCard slots assembly . . . . . . . . . . 115 2010 LCD front bezel . . . . . . . . . 119 2020 Inverter card . . . . . . . . . . 121 2030 Bluetooth daughter card (BDC-2) . . . . 122 2040 Wireless WAN antenna cable (MAIN) . . . 124 2050 LCD panel, LCD cable, and hinges . . . 127 2060 LCD rear cover and wireless LAN antenna cables . . . . . . . . . . . . . 130 Locations . . . . . . . . . . . . . . 135 Front view . . . . . . . . . . . . 135 Rear view . . . . . . . . . . . . . 137 Bottom view . . . . . . . . . . . . 138 Parts list . . . . . . . . . . . . . . 139 Overall . . . . . . . . . . . . . 140 LCD FRUs . . . . . . . . . . . . 160 Keyboard . . . . . . . . . . . . . 166 Recovery CDs . . . . . . . . . . . 167 Miscellaneous parts . . . . . . . . . . 171 AC adapters . . . . . . . . . . . . 172 Optional FRUs . . . . . . . . . . . 172 Common parts list . . . . . . . . . . 173 Notices . . . . . . . . . . . . . . 175 Trademarks . . . . . . . . . . . . . 177 iv MT 2529, 2530, 2531, 2532 About this manual This manual contains service and reference information for ThinkPad® Z60m (MT 2529, 2530, 2531, and 2532) products. Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers. v The product-specific section includes service, reference, and product-specific parts information. Important This manual is intended for trained service personnel who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a ThinkPad product, be sure to review the safety information under “Safety notices: multilingual translations” on page 8, “Safety information” on page 20, and “Laser compliance statement” on page 26. © Copyright Lenovo 2006 1 2 MT 2529, 2530, 2531, 2532 Introduction Important service information Important BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/think/ support Advise customers to contact the Customer Support Center at 800-426-7378 if they need assistance in obtaining or installing any diskette fixes. Customers in Canada should call the Customer Support Center at 800-565-3344 for assistance or download information. Strategy for replacing FRUs Before replacing parts Make sure that all diskette fixes are installed before replacing any FRUs listed in this manual. Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect. © Copyright Lenovo 2006 3 Important service information Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten. Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: v Do not drop a system board or apply any excessive force to it. v Avoid rough handling of any kind. v Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset. How to use error messages Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU Index for the computer you are servicing. Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, PC Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). Custom Model Variant (CMV) This is a unique configuration that has been negotiated between IBM and the customer. A unique 4-digit MT and 4 MT 2529, 2530, 2531, 2532 Important service information 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special bid offering. Therefore, it is NOT generally announced. v The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15). v The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). v eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15 will be found on the eSupport site.) v The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are custom models and are not found in the HMM. General Announce Variant (GAV) This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U). Also, PEW, eSupport, and the HMM will list these products under the same fixed model number. FRU identification for CTO, CMV, and GAV products There are three information resources to identify which FRUs are used to support CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM. Using PEW v PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CTO, CMV and GAV products at a MT - serial number level. An example of key commodities are hard disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory. v Remember, All CTO and CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs are loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U). v PEW can be accessed at the following Web site: http://w3-3.ibm.com/pc/entitle Click on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. Introduction 5 Important service information v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.com Using eSupport For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) v eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW). v eSupport can be accessed at the following Web site: http://www.lenovo.com/think/ support v To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP. Type in the model type and serial number. The key commodities will be returned in the eSupport record under PARTS SHIPPED WITH YOUR SYSTEM. For the Remaining FRUs (the complete list of FRUs at the MT Model level) v eSupport can be used to view the complete list of FRUs for a machine type and model. v To view the complete list of FRUs, type in the machine type and model (Example: 1829-CTO) under QUICK PATH. Under “View by Document Type” select PARTS INFORMATION. Under “Filter by Category” select SERVICE PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The list of service parts by description, with applicable machine type model and FRU will be displayed. Using the HMM Use the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level. 6 MT 2529, 2530, 2531, 2532 Important service information Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. So, if the original FRU parts are non compliant, replacement parts can also be non compliant. In all cases if the original FRU parts are RoHS compliant the replacement part must also be RoHS compliant. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo's requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs. RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date , failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used. Introduction 7 Important service information Products marketed before June 2006 Products marketed after June 2006 Current or original part Replacement FRU Current or original part Replacement FRU Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS Non-RoHS Can be RoHS Non-RoHS Can sub to RoHS RoHS Must be RoHS Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order. Related web URLs are: v IBM Information for Suppliers website: http://www-03.ibm.com/procurement/proweb.nsf/ ContentDocsByTitle/United+States~Information+for +suppliers v RoHS Directive: http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/ l_037/l_03720030213en00190023.pdf v California Senate Bills 20, 50: http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/ 2004/Presentation/MPaparian.pdf Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette drive Diskette capacity Compatibility 3.5-inch 1.0 MB Read and write 2.0 MB Read and write 4.0 MB Not compatible Safety notices: multilingual translations In this manual, safety notices appear in English with a page number reference to the appropriate multilingual, translated safety notice found in this section. The following safety notices are provided in English, French, German, Hebrew, Italian, and Spanish. 8 MT 2529, 2530, 2531, 2532 Safety notices Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi. Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. Introduction 9 Safety notices Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre feu ou d’exploser. Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen. (continued) 10 MT 2529, 2530, 2531, 2532 Safety notices (continuation of safety notice 2) Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa. Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma. Introduction 11 Safety notices Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie inappropriée risque de prendre feu ou d’exploser. Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen. (continued) 12 MT 2529, 2530, 2531, 2532 Safety notices (continuation of safety notice 3) La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa. Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al sustituir la batería. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma. Introduction 13 Safety notices Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie, d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile inappropriée risque de prendre feu ou d’exploser. Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen. (continued) 14 MT 2529, 2530, 2531, 2532 Safety notices (continuation of safety notice 4) La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa. La batería de repuesto es una batería de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local. Introduction 15 Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage. Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht werden. Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere. Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse. 16 MT 2529, 2530, 2531, 2532 Safety notices Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen. Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore. Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. Introduction 17 Safety notices Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves. Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu entzünden oder Verletzungen bei Personen hervorzurufen. Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione. Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal. 18 MT 2529, 2530, 2531, 2532 Safety notices Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface. Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird. Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione. Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de conexión entre dispositivos. Introduction 19 Safety information Safety information The following section presents safety information with which you need to be familiar before you service a ThinkPad computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. v Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe. v Before you start the machine, make sure that other service representatives and the customer’s personnel are not in a hazardous position. v Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine. v Keep your toolcase away from walk areas so that other people will not trip over it. v Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. v Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8 centimeters (3 inches) from the end. v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Attention: Metal objects are good electrical conductors. v Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. 20 MT 2529, 2530, 2531, 2532 Safety information v After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer. v Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers. WARNING Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Electrical safety Observe the following rules when working on electrical equipment. Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. v Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. v Do not work alone under hazardous conditions or near equipment that has hazardous voltages. v Disconnect all power before: – Performing a mechanical inspection – Working near power supplies – Removing or installing main units v Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position. v If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Introduction 21 Safety information – Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power, if necessary. – Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body. – When using testers, set the controls correctly and use the approved probe leads and accessories for that tester. – Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages. v Regularly inspect and maintain your electrical hand tools for safe operational condition. v Do not use worn or broken tools and testers. v Never assume that power has been disconnected from a circuit. First, check that it has been powered off. v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) v If – – – 22 an electrical accident occurs: Use caution; do not become a victim yourself. Switch off power. Send another person to get medical aid. MT 2529, 2530, 2531, 2532 Safety information Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: v Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock) v Explosive hazards, such as a damaged CRT face or a bulging capacitor v Mechanical hazards, such as loose or missing hardware To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected. Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Power off the computer. Disconnect the power cord. 3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground. b. The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any non-ThinkPad alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. Introduction 23 Safety information 8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with. Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: v Keep the parts in protective packages until they are inserted into the product. v Avoid contact with other people. v Wear a grounded wrist strap against your skin to eliminate static on your body. v Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. v Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. v Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement. Note The use of a grounding system to guard against ESD damage is desirable but not necessary. – Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. 24 MT 2529, 2530, 2531, 2532 Safety information – Use the round ground prong of the ac plug on ac-operated computers. Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Introduction 25 Laser compliance statement Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products. 26 MT 2529, 2530, 2531, 2532 Laser compliance statement If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following: CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposição à radiação. Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage et d’utilisation des commandes, ainsi que les procédures décrites. Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefährliche Laserstrahlung auftreten. L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle specificate possono provocare l’esposizione a. El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí especificados puede provocar la exposición a radiaciones peligrosas. Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open. Introduction 27 Laser compliance statement A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz. Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon. Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden. Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel. Kerülje a sugárnyalábbal való érintkezést !. Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio. Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz de luz. Evite la exposición directa al haz. 28 MT 2529, 2530, 2531, 2532 General descriptions The desciptions in this chapter apply to any ThinkPad model that has the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer. Read this first Before you go to the checkout guide, be sure to read this section. Important notes v Only certified trained personnel should service the computer. v Before replacing any FRU, read the entire page on removing and replacing FRUs. v When you replace FRUs, use new nylon-coated screws. v Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten. v Replace an FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model of the machine and the FRU part number are correct by referring to the FRU parts list. v A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do not replace the FRU. v Be careful not to replace a nondefective FRU. What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer © Copyright Lenovo 2006 29 Read this first __ 2. __ 3. __ 4. __ 5. __ 6. __ 7. __ 8. __ 9. Date of service Date on which the machine failed Date of purchase Failure symptoms, error codes appearing on the display, and beep symptoms Procedure index and page number in which the failing FRU was detected Failing FRU name and part number Machine type, model number, and serial number Customer’s name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use. Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list: The following are not covered under warranty: v LCD panel cracked from the application of excessive force or from being dropped v Scratched (cosmetic) parts v Distortion, deformation, or discoloration of the cosmetic parts v Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force v Damage caused by liquid spilled into the system v Damage caused by the improper insertion of a PC Card or the installation of an incompatible card v Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels v Damaged or bent diskette eject button v Fuses blown by attachment of a nonsupported device v Forgotten computer password (making the computer unusable) v Sticky keys caused by spilling a liquid onto the keyboard The following symptoms might indicate damage caused by nonwarranted activities: v Missing parts might be a symptom of unauthorized service or modification. v If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped. 30 MT 2529, 2530, 2531, 2532 Related service information Related service information This section provides information about the following: v “Service Web site” v “Restoring the pre-installed system” v “Passwords” on page 32 v “Power management” on page 35 Service Web site When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/think/spm Restoring the pre-installed system When the hard disk drive is replaced because of a failure, no Product Recovery program is on the new hard disk. In this case, you must use the recovery CD for the computer. Order the recovery CD and the hard disk drive at the same time so that you can recover the new hard disk drive with the pre-installed software when they arrive. For information on which CD to order, see “Recovery CDs” on page 167. Recovery to Factory Contents by using Product Recovery CDs To create the service partition and install the factory contents from the recovery CD, do the following: Note The recovery process might take up to 2 hours. 1. Insert the recovery CD into the CD or DVD drive, then restart the computer. 2. Following message is displayed: “Your computer originally included a Product Recovery program ... Reinstall the Product Recovery program? (Y/N) [ ]”. 3. Press Y key. The service partition is created and loaded with the Product Recovery program files. 4. At next window, press Enter to continue. v The service partition is created. The system automatically reboots during this process. v The recovery process copies some files to the service partition, and PKUNZIPs others. v Follow the prompts. You may be prompted to change CDs. v When the process is complete, the system reboots. General descriptions 31 Related service information 5. If you get a message asking which operating system to install, select the proper operating system and press Enter. 6. A message is displayed: “Full Recovery:”. Press Enter to select. 7. On each of the next three windows, press the Y key. 8. Follow the prompts to complete the recovery. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted. Power-on password: A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted. Hard-disk password: There are two hard-disk passwords (HDPs): v User HDP—for the user v Master HDP—for the system administrator, who can use it to get access to the hard disk even if the user has changed the user HDP Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user. Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, Lenovo does not provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. Supervisor password: A supervisor password (SVP) protects the system 32 MT 2529, 2530, 2531, 2532 Related service information information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration. Attention: If the SVP has been forgotten and cannot be made available to the servicer, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee. How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 73. 3. Remove the backup battery. For how to remove the backup battery, see “1100 Backup battery” on page 89. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5. Reinstall the backup battery and the battery pack. (B) If an SVP has been set and is known by the servicer: 1. Turn on the computer; then, while the “To interrupt normal startup, press the blue ThinkVantage button” message is displayed at the lower-left of the screen, press the ThinkVantage button. Rescue and Recovery screen opens. Note: To check whether the ThinkPad computer supports the Passphrase function, enter BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. 2. Click Access BIOS. The system Restart Required window is displayed. 3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens. 4. Select Security, using the cursor directional keys to move down the menu. 5. Select Password. 6. Select Power-On Password. General descriptions 33 Related service information 7. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 8. In the Changes have been saved window, press Enter. 9. Press F10; then, in the Setup confirmation window, select Yes . How to remove the hard-disk password Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the servicer, Lenovo does not provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the following: 1. Turn on the computer; then, while the “To interrupt normal startup, press the blue ThinkVantage button” message is displayed at the lower-left of the screen, press the ThinkVantage button. The Rescue and Recovery screen opens. For models supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the master HDP. For the other models, enter the master HDP. Note: To check whether the ThinkPad computer supports the Passphrase function, enter BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. 2. Click Access BIOS. The system Restart Required window is displayed. 3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens. 4. Select Security, using the cursor directional keys to move down the menu. 5. Select Password. 6. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. 7. Select Master HDP. 8. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 9. Press F10. 10. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed. 34 MT 2529, 2530, 2531, 2532 Related service information Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key. Standby mode When the computer enters standby mode, the following events occur in addition to what occurs in screen blank mode: v The LCD is powered off. v The hard disk drive is powered off. v The CPU stops. To enter standby mode, press Fn+F4. Note: If you are using the ACPI operating system, you can change the action of Fn+F4. In certain circumstances, the computer goes into standby mode automatically: v If a “suspend time” has been set on the timer, and the user does not do any operation with the keyboard, the ® TrackPoint , the hard disk, the parallel connector, or the diskette drive within that time. v If the battery indicator blinks orange, indicating that the battery power is low. (Alternatively, if Hibernate when battery becomes low has been selected in the “Power Management Properties” window, the computer goes into hibernation mode.) To cause the computer to return from standby mode and resume operation, do one of the following: v Press the Fn key. v Open the LCD cover. v Turn on the power switch. Also, in either of the following events, the computer automatically returns from standby mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. General descriptions 35 Related service information v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off. Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system. To cause the computer to enter hibernation mode, do any of the following: v Press the Fn+F12 keys. v If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action. – Closing the lid. – Pressing the power button. – Pressing Fn+F4 keys. Also, the computer goes into hibernation mode automatically in either of the following conditions: v If a “hibernation time” has been set on the timer, and if the user does not do any operation with the keyboard, the TrackPoint, the hard disk drive, the parallel connector, or the diskette drive within that time. v If the timer conditions are satisfied in suspend mode. When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive. 36 MT 2529, 2530, 2531, 2532 Checkout guide Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the operation. Testing the computer The ThinkPad computer has a test program called PC-Doctor® DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “Product overview” on page 47. For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by use of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter. Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If you test one of these devices, you will need to enable it by using PS2.EXE. PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the docking station. To test a USB device, connect it to the USB connector of the computer. Creating the PC-Doctor diagnostics diskette To create the PC-Doctor disk from the Access IBM Predesktop Area, do as follows: 1. Enter the Predesktop application by pressing the ThinkVantage button during POST. 2. When the Access application finishes loading, double-click the “Create Diagnostic Diskettes” icon. 3. Authenticating the digital signature takes about 15 seconds; then the ThinkPad computer will reboot into PC-DOS. General descriptions 37 Checkout guide 4. A batch file automatically starts up to prompt you through the process of creating diskettes. You are notified of how many diskettes you will need. a. You are prompted to insert each diskette in sequence. b. Typically, all you need to do is to press the Enter key for the floppy drive; the system then formats and creates the diskette. c. Each diskette is erased and formatted with the PC-Doctor for DOS boot image. 5. Once all the diskettes have been created, the ThinkPad computer will reboot. The user is asked to remove all diskettes from the drive, or to insert the first diskette created if it is desired to run the diagnostics. To run the test, do as follows: Note: In the following procedure, you can select an item not only with the arrow keys, but also with the TrackPoint pointer. Instead of pressing Enter, click the left button. 1. Insert the PC-Doctor disk into the diskette drive; then power on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 41, and check the power sources. If an error code appears, go to “Symptom-to-FRU index” on page 58. On the first screen, select the model and press Enter. Follow the instructions on the screen. 2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. 38 MT 2529, 2530, 2531, 2532 Checkout guide Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices Communication Wireless LAN Memory Test - Full Memory Test - Quick PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus. Press ENTER to select. The options on the test menu are as follows: Diagnostics v v v v v v v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices ThinkPad Devices Communication Wireless LAN Memory Test – Full Memory Test – Quick Interactive Tests v v v v v v v v Keyboard Video Internal Speaker Mouse Diskette System Load CD-ROM/DVD Test Intel Wireless Radio Notes: v In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; otherwise, it cannot be sensed. v Video Adapter test supports only the LCD display on the ThinkPad computer. If you have an external monitor attached to your computer, detach it before running PC-Doctor for DOS. 4. Run the applicable function test. 5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it. 6. To exit the test, select Quit — Exit Diag. To cancel the test, press Esc. Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect. General descriptions 39 Checkout guide Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v v v v v v v v v v v System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive 40 MT 2529, 2530, 2531, 2532 Checkout guide Power system checkout To 1. 2. 3. 4. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the ac adapter and install the charged battery pack. 7. Check that the battery pack supplies power when you turn on the computer. If you suspect a power problem, see the appropriate one of the following power supply checkouts: v “Checking the ac adapter” v “Checking operational charging” on page 42 v “Checking the battery pack” on page 42 v “Checking the backup battery” on page 43 Checking the ac adapter You are here because the computer fails only when the ac adapter is used. v If the power problem occurs only when the port replicator is used, replace the port replicator. v If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation. v If the computer does not charge during operation, go to ″Checking operational charging.″ To check the ac adapter, do the following: 1. Unplug the ac adapter cable from the computer. 2. Measure the output voltage at the plug of the ac adapter cable. See the following figure: 3 2 1 Pin Voltage (V dc) 1 +20 2 0 3 Ground (20V) Note: Output voltage of pin no.2 of the ac adapter may different from the one you are servicing. 3. If the voltage is not correct, replace the ac adapter. 4. If the voltage is acceptable, do the following: v Replace the system board. General descriptions 41 Checkout guide v If the problem persists, go to “Product overview” on page 47. Note: Noise from the ac adapter does not always indicate a defect. Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack. If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section. Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment (but do not click), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon. Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it. To check the battery pack, do the following: 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 5 (−). See the following figure: 42 MT 2529, 2530, 2531, 2532 Checkout guide 7(+) 6(+) 5 4 3 1(-) 2(-) Terminal Voltage (V dc) 1 + 0 to + 16.8 5 Ground (−) 3. If the voltage is less than +11.0 V dc, the battery pack has been discharged. Note: Recharging will take at least 3 hours, even if the indicator does not turn on. If the voltage is still less than +11.0 V dc after recharging, replace the battery. 4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 4 and 5. The resistance must be 4 to 30 K
. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board. Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 73). 4. Remove the backup battery (see “1100 Backup battery” on page 89). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board. v If the voltage is not correct, replace the backup battery. v If the backup battery discharges quickly after replacement, replace the system board. General descriptions 43 Checkout guide 44 MT 2529, 2530, 2531, 2532 ThinkPad Z60m Product overview . . . . . . . . . . . . 47 Specifications . . . . . . . . . . . . 47 Status indicators . . . . . . . . . . . 50 FRU tests . . . . . . . . . . . . . 53 Fn key combinations . . . . . . . . . . 55 Symptom-to-FRU index . . . . . . . . . . 58 Numeric error codes . . . . . . . . . . 58 Error messages . . . . . . . . . . . 63 Beep symptoms . . . . . . . . . . . 65 No-beep symptoms . . . . . . . . . . 65 LCD-related symptoms . . . . . . . . . 66 Intermittent problems . . . . . . . . . . 67 Undetermined problems . . . . . . . . . 67 FRU replacement notices . . . . . . . . . 68 Screw notices . . . . . . . . . . . . 68 Retaining serial numbers. . . . . . . . . 69 Restoring the serial number of the system unit 69 Retaining the UUID . . . . . . . . . 70 Reading or writing the ECA information . . . 70 Removing and replacing a FRU. . . . . . . . 72 1010 Battery pack. . . . . . . . . . . 73 1020 Ultrabay Enhanced device . . . . . . 75 1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails . . . . . . . 76 1040 Palm rest or palm rest with fingerprint reader 79 1050 DIMM . . . . . . . . . . . . 81 1060 Keyboard . . . . . . . . . . . 82 1070 Mini PCI adapter for wireless LAN . . . . 84 1080 Modem daughter card (MDC-1.5) . . . . 85 1090 PCI Express Mini card for wireless WAN 87 1100 Backup battery . . . . . . . . . . 89 1110 Wireless WAN antenna cable (DIV) . . . . 90 1120 Keyboard bezel and speaker assembly . . . 92 1130 Fan assembly . . . . . . . . . . 95 1140 CPU . . . . . . . . . . . . . 99 1150 LCD assembly . . . . . . . . . . 100 1160 Base cover . . . . . . . . . . . 103 1170 3-1 Digital Media Reader sub card with cable 106 1180 USB sub card with cable . . . . . . . 108 1190 MG (magnesium) frame . . . . . . . 110 1200 System board and PC Card/ExpressCard slots assembly . . . . . . . . . . 115 2010 LCD front bezel . . . . . . . . . 119 2020 Inverter card . . . . . . . . . . 121 2030 Bluetooth daughter card (BDC-2) . . . . 122 2040 Wireless WAN antenna cable (MAIN) . . . 124 2050 LCD panel, LCD cable, and hinges . . . 127 2060 LCD rear cover and wireless LAN antenna cables . . . . . . . . . . . . . 130 Locations . . . . . . . . . . . . . . 135 © Copyright Lenovo 2006 45 Front view . . . . . . Rear view . . . . . . . Bottom view . . . . . . Parts list . . . . . . . . Overall . . . . . . . LCD FRUs . . . . . . Keyboard . . . . . . . Recovery CDs . . . . . Windows XP Professional . Windows XP Home Edition . Miscellaneous parts . . . . AC adapters . . . . . . Optional FRUs . . . . . Common parts list . . . . Tools . . . . . . . Power cords (system) . . Notices . . . . . . . . Trademarks . . . . . . . 46 MT 2529, 2530, 2531, 2532 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 137 138 139 140 160 166 167 167 169 171 172 172 173 173 174 175 177 Product overview Product overview This section presents the following product-unique information: v “Specifications” v “Status indicators” on page 50 v “FRU tests” on page 53 v “Fn key combinations” on page 55 Specifications The following table lists the specifications of the ThinkPad Z60m: Feature Description Processor v Intel Celeron 360 (1.4 GHz), 1-MB L2 cache v Intel Celeron 370 (1.5 GHz), 1-MB L2 cache v Intel Celeron 380 (1.6 GHz), 1-MB L2 cache v Intel Pentium M processor 740 (1.73 GHz), 2-MB L2 cache v Intel Pentium M processor 750 (1.86 GHz), 2-MB L2 cache v Intel Pentium M processor 760 (2.0 GHz), 2-MB L2 cache v Intel Pentium M processor 770 (2.133 GHz), 2-MB L2 cache v Intel Pentium M processor 780 (2.26 GHz), 2-MB L2 cache Bus architecture v v v v v Graphic memory chip v Intel 915GM v 64-MB GDDR SDRAM (ATI M22-CSP64) v 128-MB GDDR SDRAM (ATI M24-CSP128) Display v 15.4-inch, 16M colors, WXGA (1280 × 800 resolution) TFT color LCD v 15.4-inch, 16M colors, WXGA high brightness (1280 × 800 resolution) TFT color LCD v 15.4-inch, 16M colors, WSXGA+ (1680 × 1050 resolution) TFT color LCD 533-MHz PSB 533-MHz DDR2 SDRAM (PC2-4200) HUB link PCI bus LPC bus (continued) ThinkPad Z60m 47 Product overview Feature Description Standard memory v 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 and 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 2 v 1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 Optional memory v 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 (maximum of 2048 MB) CMOS RAM v 242 bytes Hard disk drive v 40.0 GB, 5400 rpm, 9.5 mm high, SATA interface v 60.0 GB, 5400 rpm, 9.5 mm high, SATA interface v 80.0 GB, 5400 rpm, 9.5 mm high, SATA interface v 100.0 GB, 5400 rpm, 9.5 mm high, SATA interface v 100.0 GB, 7200 rpm, 9.5 mm high, SATA interface Supported hard disk drives are depend on the model. Ultrabay Enhanced device (standard) v DVD drive, 9.5 mm high v DVD/CD-RW combo drive, 9.5 mm high v DVD-RAM/RW drive, 9.5 mm high Fingerprint reader Some models I/O port v v v v v v v v v v Internal modem v 56.6 Kbps Audio v Built-in stereo speakers v Software control volume 3-1 Digital Media Reader Stereo headphone jack Microphone jack Video-out connector (S-Video) 3 Universal Serial Bus (USB) connectors IEEE 1394 connector Infrared port RJ11 telephone connector RJ45 Ethernet connector Docking connector (continued) 48 MT 2529, 2530, 2531, 2532 Product overview Feature Description Infrared transfer v IrDA 1.1 Ethernet (on the system board) v Gigabit Ethernet Mini PCI adapter v Intel PRO Wireless 2200BG Mini-PCI Adapter v Intel PRO Wireless 2915ABG Mini-PCI Adapter v ThinkPad 11a/b/g Wireless LAN Mini PCI Adapter II PCI Express Mini card v Sierra Wireless EV-DO Wireless WAN Mini PCI Express Adapter PC Card /ExpressCard slots v ExpressCard (34 module, 54 module) for upper slot v PC Card (Type-II) for lower slot Bluetooth wireless v ThinkPad Bluetooth with Enhanced Data Rate (BDC-2) Modem v ThinkPad Modem (MDC-1.5, 56 kbps HDA) Touch pad v UltraNav ThinkLight Yes Battery v Li-ion battery (6 cells) 2.6 Ah v Li-ion battery (9 cells) 2.6 Ah AC adapter v 90-watt type Preinstalled operating system v Windows XP Professional v Windows XP Home Edition ThinkPad Z60m 49 Product overview Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 6 7 8 9 10 11 10 50 9 8 MT 2529, 2530, 2531, 2532 Product overview Indicator Meaning
1 Wireless status Green: The wireless feature (the IEEE 802.11 standard) is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
2 Bluetooth status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R
3 Wireless Green: WAN status The wireless feature (the IEEE 802.11 standard) is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
4 Num lock Green: The numeric keypad on the keyboard is enabled. To enable or disable the keypad, press and hold the Shift key, and press the NumLk (ScrLk) key.
5 Caps lock Green: Caps Lock mode is enabled. To enable or disable Caps Lock mode, press the Caps Lock key.
6 Drive in use Green: Data is being read from or written to the hard disk drive, the diskette drive, or the drive in the Ultrabay Enhanced device. When this indicator is on, do not put the computer into standby mode or turn off the computer. Note: Do not move the system while the green drive-in-use light is on. Sudden physical shock could cause drive errors.
7 Power on Green: The computer is on and ready to use. This indicator stays lit whenever the computer is on and is not in standby mode. (continued) ThinkPad Z60m 51 Product overview Indicator Meaning
8 Battery status Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 20% to 80% of the capacity. Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged. Orange: The battery is charged between 5% and 20% of the capacity, and being discharged. Blinking orange (slow): The battery is charged between 5% to 20% of the capacity, and being charged. Blinking orange (rapid): The battery is charged between 0% to 5% of the capacity.
9 AC power status Green: The computer is connected to the ac power supply.
10 Standby status Green: The computer is in standby mode. Blinking green: The computer is entering standby mode or hibernation mode, or is resuming normal operation.
11 Ultrabay Enhanced status Green: An Ultrabay Enhanced device is installed and in use. Blinking green: An Ultrabay Enhanced device is in the process of being detached. Turn off: An Ultrabay Enhanced device is ready to be attached or detached. Note: If you are using Windows 2000, the Ultrabay Enhanced status indicator does not blink while an Ultrabay Enhanced device is being detached. Instead, a message box pops up when the process is completed; then the indicator turns off. 52 MT 2529, 2530, 2531, 2532 Product overview FRU tests The following table shows the test for each FRU. FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad computer, undock it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running. Power Diagnostics --> ThinkPad Devices --> AC Adapter, Battery 1 ( Battery 2) LCD unit 1. Diagnostics --> Video Adapter 2. Interactive Tests --> Video Modem daughter card (MDC-1.5) 1. Make sure the modem is set up correctly. 2. Replace the modem jack and the modem card in turn, and run the following tests in Diagnostics --> Communication: a. Conexant Smart Modem Interrupt b. Conexant Smart Modem Dialtone Audio 1. Interactive Tests --> Internal Speaker 2. Diagnostics --> Other Devices --> Analog Devices HDA CODEC Test Speaker Interactive Tests --> Internal Speaker PC Card slot 1. Diagnostics --> Systemboard --> PCMCIA 2. Insert a PC Card Wrap Plug into every PC Card slot, and run Diagnostics --> Systemboard --> PCMCIA External Loop ExpressCard slot 1. Insert a PCI-Express/USB Wrap card into the ExpressCard slot. 2. Turn on the computer. 3. Run Diagnostics --> ThinkPad Devices --> ExpressCard slot. Keyboard 1. Diagnostics --> Systemboard --> Keyboard 2. Interactive Tests --> Keyboard Hard disk drive Diagnostics --> Fixed Disks Diskette drive 1. Diagnostics --> Diskette Drives 2. Interactive Tests --> Diskette DVD drive or DVD/CD-RW combo drive 1. Diagnostics --> Other Devices --> CD-ROM/DVD 2. Interactive Tests --> CD-ROM/DVD Test (continued) ThinkPad Z60m 53 Product overview FRU Applicable test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Memory Test—Quick. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. 3. If the test does not detect the error, run Diagnostics --> Memory Test—Full. Fan 1. Turn on the computer and check the air turbulence at the louver near the PC Card slot. 2. Run Diagnostics --> ThinkPad Devices --> Fan. TrackPoint or pointing device If the TrackPoint does not work, check the configuration as specified in the ThinkPad Configuration program. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem. If the pointer stops after a short time, no service action is necessary. If enabling the TrackPoint does not correct the problem, continue with the following: v Interactive Tests --> Mouse Touch Pad 54 If the Touch Pad does not work, check the configuration as specified in the ThinkPad Configuration program. If the Touch Pad is disabled, select Automatic to enable it. If enabling the Touch Pad does not correct the problem, continue with the following: v Interactive Tests --> Mouse MT 2529, 2530, 2531, 2532 Product overview Fn key combinations The following table shows the function of each combination of Fn with a function key. Key combination Description Fn+F1 Reserved. Fn+F2 Reserved. Fn+F3 Select a power scheme that has been created by Power Manager. Fn+F4 Put the computer in standby mode. To return to normal operation, press the Fn key only, without pressing a function key. Note: In Windows 2000 and Windows XP, this combination of keys functions as a sleep button. The setting can be changed so that pressing it puts the computer into hibernation mode or even shuts the computer down. Fn+F5 Enable or disable the built-in wireless networking features and the Bluetooth features. If you press Fn+F5, a list of wireless features is displayed in the Wireless Radio Control window. You can quickly change the power state of each feature in the list. Note: This function is supported only in Windows 2000 and Windows XP. Note: If you want to use this combination of keys to enable or disable the feature, the following device drivers must be installed on the computer beforehand: v ThinkPad Power Management driver v OnScreen Display utility v Wireless device drivers Fn+F6 Reserved. Fn+F7 Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Note: For any operating system other than Windows 2000 or Windows XP, no additional procedure is needed; just press Fn+F7. Notes: 1. This function does not work when different desktop images are displayed on the computer display and the external monitor (the Extend desktop function). 2. This function does not work while a DVD movie or a video clip is playing. 3. For Windows 2000 or Windows XP, a hotkey application might take over the switching function. (continued) ThinkPad Z60m 55 Product overview Key combination Description Fn+F8 Change the settings of the TrackPoint and the touch pad. Fn+F9 Open the ThinkPad EasyEject Utility screen. Buttons for the following choices are displayed: v Eject ThinkPad PC from Dock: This button is displayed only if the ThinkPad computer has been attached to a ThinkPad Advanced Dock or a ThinkPad Advanced Mini Dock. The computer can be detached from the ThinkPad Advanced Dock or the ThinkPad Advanced Mini Dock. v Eject ThinkPad PC from Mini Dock: This button is displayed only if the ThinkPad computer has been docked in a ThinkPad Advanced Mini Dock and one or more USB devices have been connected to the ThinkPad Advanced Mini Dock. You can stop and remove all the USB devices safely by clicking the button. Note: If a diskette drive is connected to the external-diskette-drive connector of the ThinkPad Advanced Mini Dock, you cannot connect a USB diskette drive. v Run EasyEject Actions: This button is used to select, stop, or remove external devices connected to the ThinkPad computer. v Configure EasyEject Actions: Opens the ThinkPad EasyEject Utility main window. v Fn+F9 Settings: Configures the settings for the Fn+F9 function. You can use this utility to stop and remove all ejectable devices connected to the ThinkPad computer, the ThinkPad Advanced Mini Dock, or the ThinkPad Essential Port Replicator. You cannot use it to detach the computer from the ThinkPad Advanced Mini Dock or the ThinkPad Essential Port Replicator. Note: This function is supported only in Windows 2000 and Windows XP. Fn+F10 Reserved. Fn+F11 Reserved. Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds. Note: To use Fn+F12 for hibernation in Windows 2000 or Windows XP, you must have the PM device driver installed on the computer. (continued) 56 MT 2529, 2530, 2531, 2532 Product overview Key combination Description Fn+PgUp Turn the ThinkLight on or off. Note: This function is supported only on the ThinkPad computers that have the ThinkLight. The on or off status of the ThinkLight is shown on the screen for a few seconds when you press Fn+PgUp. Fn+Home The computer display becomes brighter. Fn+End The computer display becomes dimmer. Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Has the same function as the SysRq key. Fn+ScrLk Enable or disable the numeric keypad. Fn+Pause Has the same function as the Break key. Fn+cursor keys These key combinations work with Windows Media Player. Fn+down arrow key works for the Play or Pause button, Fn+up arrow key for the Stop button, Fn+right arrow key for the Next Track button, and Fn+left arrow key for the Previous Track button. ThinkPad Z60m 57 Symptom-to-FRU index Symptom-to-FRU index The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU. This index can also help you determine, during regular servicing, what FRUs are likely to need to be replaced next. A numeric error is displayed for each error detected in POST or system operation. In the displays, n can be any number. If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not described there, go to “Intermittent problems” on page 67. Note For a device not supported by diagnostic codes in the ThinkPad notebook computers, see the manual for that device. Numeric error codes Symptom or error FRU or action, in sequence 0175 Bad CRC1, stop POST task—The EEPROM checksum is not correct. System board. 0176 System Security—The system has been tampered with. 1. Run BIOS Setup Utility, and save the current setting by pressing F10. 2. System board. 0177 Bad SVP data, stop POST task—The checksum of the supervisor password in the EEPROM is not correct. System board. 0182 Bad CRC2. Enter BIOS Setup and load Setup defaults.—The checksum of the CRS2 setting in the EEPROM is not correct. 1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10. 2. System board. 58 MT 2529, 2530, 2531, 2532 Symptom-to-FRU index Symptom or error FRU or action, in sequence 0185 Bad startup sequence settings. Enter BIOS Setup and load Setup defaults. 1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10. 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 Invalid RFID configuration information area—The EEPROM checksum is not correct. System board. 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1. Run BIOS Setup Utility, and then save current setting by pressing F10. 2. System board. 0192 System Security— IBM Embedded Security hardware tamper detected. System board. 0199 1. Run BIOS Setup Utility, System Security—IBM Security and then save the current password retry count exceeded. setting by pressing F10. 2. System board. 01C8 Two or more modem devices are found. Remove all but one of them. Press to continue. 1. Remove either a Mini-PCI Card or a modem daughter card. Otherwise, press Esc to ignore the warning message. 2. System board. 01C9 1. Remove the Ethernet More than one Ethernet devices device that you installed; are found. Remove one of or press Esc to ignore the them. Press to continue. warning message. 2. System board. 01CA 1. Remove the wireless LAN More than one Wireless LAN device that you installed. devices are found. Remove one 2. System board. of them. 0200 Hard disk error—The hard disk is not working. 1. Reseat the hard disk drive. 2. Load Setup Defaults in BIOS Setup Utility. 3. Hard disk drive. 4. System board. ThinkPad Z60m 59 Symptom-to-FRU index Symptom or error FRU or action, in sequence 021x Keyboard error. Run interactive tests of the keyboard and the auxiliary input device. 0220 Monitor type error—Monitor type does not match the one specified in CMOS. Load Setup Defaults in BIOS Setup Utility. 0230 Shadow RAM error—Shadow RAM fails at offset nnnn. System board. 0231 System RAM error—System RAM fails at offset nnnn. 1. DIMM. 2. System board. 0232 Extended RAM error— Extended RAM fails at offset nnnn. 1. DIMM. 2. System board. 0250 System battery error—System battery is dead. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0252 Password checksum bad—The password is cleared. Reset the password by running BIOS Setup Utility. 0260 System timer error. 1. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 2. System board. 0270 Real-time clock error. 1. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 2. System board. 0271 Date and time error—Neither the date nor the time is set in the computer. Run BIOS Setup Utility to reset the time and date. 0280 Previous boot incomplete— Default configuration used. 1. Load “Setup Default” in BIOS Setup Utility. 2. DIMM. 3. System board. 02F5 DMA test failed. 1. DIMM. 2. System board. 02F6 Software NMI failed 1. DIMM. 2. System board. 02F7 Fail-safe timer NMI failed 1. DIMM. 2. System board. 60 MT 2529, 2530, 2531, 2532 Symptom-to-FRU index Symptom or error FRU or action, in sequence 1802 Unauthorized network card is plugged in—Turn off and remove the miniPCI network card. 1. Remove Mini PCI network card. 2. System board. 1803 Unauthorized daughter card is plugged in—Turn off and remove the daughter card. 1. Remove the daughter card that you installed. 2. System board. 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1810 Hard disk partition layout error. 1. If the Access IBM Predesktop Area has been previously disabled, then go to the BIOS Setup Utility by pressing F1 to open the BIOS Setup Utility. Select Security --> Predesktop Area --> Access IBM Predesktop Area. Set this item to Disabled. Save and exit. 2. If the Access IBM Predesktop Area has not been previously disabled, press Enter to load Access IBM Predesktop Area. Then run RECOVER TO FACTORY CONTENTS in Access IBM Predesktop Area. 3. If item 2 failed, press F3 in the Welcome screen in RECOVER TO FACTORY CONTENTS. Run FDISK, and then delete all partitions. Run RECOVER TO FACTORY CONTENTS in Access IBM Predesktop Area again. 4. If item 3 failed, select CD-ROM boot in Startup in Access IBM Predesktop Area. Boot from the Recovery CD and perform full recovery from it. 5. If item 4 failed, replace the hard disk drive. ThinkPad Z60m 61 Symptom-to-FRU index Symptom or error FRU or action, in sequence 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication. 2000 Hard Drive Active Protection sensor diagnostics failed. Press to continue. Press to enter SETUP 1. Undock docking station or port replicator if it is attached to the ThinkPad computer, and place the computer on a horizontal surface. Do not apply any physical shock to the computer. 2. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. 2010 Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed. Inform the following information to the customer: If in the primary bay the customer is using a non-IBM or non-Lenovo hard disk drive (HDD), or an old generation IBM HDD which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC. If in the primary drive bay the customer is using a supported IBM/Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at http://www.lenovo.com/think/ support 2100 Initialization error on HDD0 (Main hard disk drive) 1. Reseat the hard disk drive. 2. Main hard disk drive. 3. System board. 2102 Initialization error on HDD1 (Ultrabay hard disk drive) 1. Reseat the hard disk drive. 2. Ultrabay hard disk drive. 3. System board. 2110 Read error on HDD0 (Main hard disk drive) 1. Reseat the hard disk drive. 2. Main hard disk drive. 3. System board. 2112 Read error on HDD1 (Ultrabay hard disk drive) 1. Reseat the hard disk drive. 2. Ultrabay hard disk drive. 3. System board. 62 MT 2529, 2530, 2531, 2532 Symptom-to-FRU index Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Operating system not found. 1. Check that the operating system has no failure and is installed correctly. 2. Enter the BIOS Setup Utility and see whether the hard disk drive and the diskette drive are properly identified. 3. Reseat the hard disk drive. 4. Reinstall the operating system. 5. Diskette drive. 6. Hard disk drive. 7. System board. Hibernation error. 1. Restore the system configuration to what it was before the computer entered hibernation mode. 2. If memory size has been changed, re-create the hibernation file. Fan error. Fan. Thermal sensing error. System board. Authentication of system services failed. Press to resume. The Predesktop Area in the HDD is corrupted. Restore it from a recovery CD. ThinkPad Z60m 63 Symptom-to-FRU index Symptom or error FRU or action, in sequence Cannot boot from any device. Check the status of device which you want to boot from. Device not found. 1. The device you want to boot from. 2. System board. Device Error. 1. The device you want to boot from. 2. System board. No valid operating system. 1. Check that the operating system has no failure and is installed correctly. 2. Reinstall the operation system. Excluded from boot order. v Enter the BIOS Setup Utility and add the device in boot order. 64 MT 2529, 2530, 2531, 2532 Symptom-to-FRU index Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector. 2. LCD assembly. 3. External CRT. 4. System board. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 58. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2. System board One short beep, pause, three short beeps, pause, three more short beeps, and one short beep. Only the cursor appears. Reinstall the operating system. Four cycles of four short beeps and a blank screen. System board (security chip) Five short beeps and a blank screen. System board No-beep symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, and no POST. 1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST. 1. Reseat DIMM. The power-on password prompt appears. A power-on password or a supervisor password is set. Type the password and press Enter. The hard-disk password prompt appears. A hard-disk password is set. Type the password and press Enter. The DOS full screen looks smaller than it should. Start the ThinkPad Configuration program and set the Screen expansion function. 2. System board. ThinkPad Z60m 65 Symptom-to-FRU index LCD-related symptoms Important The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is: v WXGA: 8 or more bright dots, 8 or more dark dots, or a total of 9 or more bright and dark dots. v WSXGA+: 11 or more bright dots, 13 or more dark dots, or a total of 16 or more bright and dark dots. Note: A bright dot means a pixel is always on (white or color.) A dark dot means a pixel is always off (black color.) Symptom or error FRU or action, in sequence No beep, power-on indicator on, and a blank LCD during POST. System board. v LCD backlight not working. v LCD too dark. v LCD brightness cannot be adjusted. v LCD contrast cannot be adjusted. 1. Reseat the LCD connectors. 2. LCD assembly. 3. System board. v v v v LCD screen unreadable. Characters missing pixels. Screen abnormal. Wrong color displayed. Horizontal or vertical lines displayed on LCD. 66 1. See important note for “LCD-related symptoms.” 2. Reseat all LCD connectors. 3. LCD assembly. 4. System board. LCD assembly. MT 2529, 2530, 2531, 2532 Symptom-to-FRU index Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist. Undetermined problems If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects). Verify that all attached devices are supported by the computer. Verify that the power supply being used at the time of the failure is operating correctly. (See “Power system checkout” on page 41.) 1. Turn off the computer. 2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices: a. Non-ThinkPad devices b. Devices attached to the port replicator c. Printer, mouse, and other external devices d. Battery pack e. Hard disk drive f. External diskette drive g. DIMM h. CD-ROM and diskette drive in the Ultrabay i. PC Cards 4. Turn on the computer. 5. Determine whether the problem has been solved. 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a. System board b. LCD assembly ThinkPad Z60m 67 FRU replacement notices FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once. Do the following when you service this machine: v Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 171) in your tool bag. v Always use new screws. v Use a torque screwdriver if you have one. Tighten screws as follows: v Plastic to plastic Turn an additional 90 degrees after the screw head touches the surface of the plastic part: 90 degrees more (Cross-section) v Logic card to plastic Turn an additional 180 degrees after the screw head touches the surface of the logic card: 180 degrees more (Cross-section) v Torque driver If you have a torque driver, refer to the “Torque” column for each step. 68 MT 2529, 2530, 2531, 2532 FRU replacement notices v Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all of the screws are tightened firmly. Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” on page 70 v “Reading or writing the ECA information” on page 70 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer. If you replace the system board, you must restore the serial number of the system unit to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 2. Read S/N data from EEPROM. The serial number of each device in your computer is displayed; the serial number of the system unit is listed as follows: v 20: Serial number Write down that number. Note: The serial number of the system unit is also written on the label attached to the bottom of the computer. After you have replaced the system board, restore the serial number by doing the following: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen. ThinkPad Z60m 69 FRU replacement notices Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board. The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten. Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.73 or later. 1. Insert the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the instruction. 4. To read box build date, select 5. Read box build date from EEPROM, and follow the instruction on the screen. After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's application. Use the ThinkPad Hardware Maintenance Diskette Version 1.73 or later to update the EEPROM. Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed be the same as the machine type of the machine that had the ECA applied to it. 1. Insert the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 70 MT 2529, 2530, 2531, 2532 FRU replacement notices 3. To write ECA information, select 1. Write ECA/rework number from EEPROM, and follow the instruction. 4. To write box build date, select 4. Write box build date from EEPROM, and follow the instruction on the screen. If the system board is being replaced, try to read the ECA information from the old system board and transfer the information to the new system. If the system board is inoperable, this will not be possible. ThinkPad Z60m 71 Removing and replacing a FRU Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 68. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps for removing the FRU, as given in the drawings by the numbers in square callouts. 5. When turning a screw to replace a FRU, turn it in the direction as given by the arrow in the drawing. 6. When removing the FRU, move it in the direction as given by the arrow in the drawing. 7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to replacement. For information about connecting and arranging internal cables, see “Locations” on page 135. 8. When replacing a FRU, use the correct screw as shown in the procedures. DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits. Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge (ESD) strap (P/N 6405959). 72 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Unlock the battery release lever
1. Holding the battery release lever in the unlocked position
2, remove the battery pack in the direction shown by arrow
3. 1 2 3 ThinkPad Z60m 73 Removing and replacing a FRU When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is locked, as in this figure. 2 1 74 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1020 Ultrabay Enhanced device Note Ultrabay Enhanced does not accept any of the following devices: v Ultrabay Plus devices v Ultrabay 2000 devices For devices compatible with the Ultrabay Enhanced bay, see “Optional FRUs” on page 172. Note: When you release the switch in step
1, the lever pops out. In step
2, pull the lever a little to release the device from the bay. 1 2 3 ThinkPad Z60m 75 Removing and replacing a FRU 1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails For access, remove this FRU: v “1010 Battery pack” on page 73 Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode. 1 Step Screw (quantity)
1 HDD screw (1) or security screw (1) Note: Use a 2.5-mm Allen wrench to remove the security screw. (continued) 76 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 3 2 4 When installing: Make sure that the hard disk drive connector is attached firmly. (continued) ThinkPad Z60m 77 Removing and replacing a FRU 5 6 6 When installing: Rubber rails of the hard disk drive must be attached to the replacement drive. Otherwise the hard disk drive cannot be properly installed to the computer. 78 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1040 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 73 Notes In models with the fingerprint reader, the sensor has been attached to the palm rest FRU as the child part. If the fingerprint reader has any defects and needs to be replaced, you need to replace the palm rest by the procedures given in this section. These procedures are the same for a palm rest with or without a fingerprint reader. 1 1 1 1 Step Icon
1 Screw (quantity) Color Torque M2 × 17 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 79 Removing and replacing a FRU In step
2, press the left and right sides of the palm rest toward the center to release the side latches, as in this figure. Then release the latches indicated by arrow
3. 3 2 2 Pull the palm rest a little in the direction shown by arrow
4, and then detach the touch pad connector by pulling the tab with your fingers in the direction shown by arrow
5. 4 5 When installing: Make sure that the touch pad connector is attached firmly. 80 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1050 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 1 2 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily. ThinkPad Z60m 81 Removing and replacing a FRU 1060 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 1 Step
1 Icon Screw (quantity) Color Torque M2 × 17 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm) Lift the keyboard a little in the direction shown by arrow
2, and then detach the connector
3. 2 3 82 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU When installing: Make sure that the keyboard edges
a are under the frame as shown in this figure. a a ThinkPad Z60m 83 Removing and replacing a FRU 1070 Mini PCI adapter for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 In steps
2a and
2b, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159), or pick the connectors with your fingers and gently unplug them in the direction shown by the arrow. 3 1 2a 2b 1 When installing: 1. Plug the gray cable
2a into the jack labeled MAIN on the card, and the black cable
2b into jack AUX. 2. Insert the notched end of the card into the socket, and then press the card firmly. Pivot the card until it snaps into place. Make sure that it is firmly fixed in the slot and does not move easily. 84 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1080 Modem daughter card (MDC-1.5) For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 1 1 2 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) In step
2, remove the card by pulling the tab with your fingers in the direction shown by the arrow. (continued) ThinkPad Z60m 85 Removing and replacing a FRU Turn the card over
3, and detach the modem connector
4. 3 4 When installing: Make sure that the modem connector and the connector on the underside of the card are attached firmly. 86 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1090 PCI Express Mini card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 In step
1a or
1b, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1b 1a Step Screw (quantity) Color Torque
2 M2 × 3 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 87 Removing and replacing a FRU 3 When installing: Plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled DIV. 88 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1100 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 2 1 When installing: Make sure that the battery connector is attached firmly. ThinkPad Z60m 89 Removing and replacing a FRU 1110 Wireless WAN antenna cable (DIV) For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1090 PCI Express Mini card for wireless WAN” on page 87 In step
1, strip off the tapes securing the antenna cable. 1 1 1 2 3 1 Step Screw (quantity) Color Torque
2 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm) 90 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU When installing: Make sure that the cable is routed along the cable guides
a, and that secured with tapes
b. a a a a a b b ThinkPad Z60m 91 Removing and replacing a FRU 1120 Keyboard bezel and speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 1 1 Step Screw (quantity) Color Torque
1 M2 × 17 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) (continued) 92 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 4 4 2 3 Strip the tape that secures the cable
2, and disconnect the speaker cable
3. Step Screw (quantity) Color Torque
5 Black 0.196 Nm (2.0 kgfcm) M2 × 3 mm, flat-head, nylon-coated (2) 5 5 (continued) ThinkPad Z60m 93 Removing and replacing a FRU 6 7 6 6 6 8 8 9 Step Screw (quantity) Color Torque
6 M2 × 3 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm) When installing: Make sure that the speaker cables are routed along the cable guides, and that the connector is attached firmly. 94 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1130 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1120 Keyboard bezel and speaker assembly” on page 92 1 1 1 1 1 1 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (6) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 95 Removing and replacing a FRU 3 96 2 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU When installing: v Before you attach the fan assembly to the computer, apply thermal grease on the part marked
a as in the following figure. a v Make sure that the fan connector is attached firmly. (continued) ThinkPad Z60m 97 Removing and replacing a FRU v When attaching the fan assembly to the frame, take care not to damage the heat sink (
b) of the fan assembly. b b 98 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1140 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow
1 to release the lock; then remove the CPU
2. 1 a b 2 When installing: Place the CPU on the CPU socket
a, and then rotate the head of the screw in the direction shown by arrow
b to secure the CPU. ThinkPad Z60m 99 Removing and replacing a FRU 1150 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 2 2 1 Step Screw (quantity) Color Torque
1 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm)
2 M2 × 9 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) (continued) 100 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 4 3 3 4 5 6 Step Screw (quantity) Color Torque
3 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm)
4 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.296 Nm (3.0 kgfcm) In step
6, release the antenna cables from the cable guides. Notes: 1. Route the antenna cables along the cable guides. When you route the cables, do not tense them. To do so, the cables may get damaged by the cable guides of the frame, and may cause a broken wire. 2. Make sure that the connector
5 is attached firmly. (continued) ThinkPad Z60m 101 Removing and replacing a FRU 7 7 102 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1160 Base cover For access, remove these FRUs, in order: v “1010 Battery pack” on page 73 v “1020 Ultrabay Enhanced device” on page 75 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 76 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1080 Modem daughter card (MDC-1.5)” on page 85 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1110 Wireless WAN antenna cable (DIV)” on page 90 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 v “1150 LCD assembly” on page 100 1 2 2 1 2 2 2 2 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm)
2 M2 × 5 mm, flat-head, nylon-coated (6) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 103 Removing and replacing a FRU Attention: Before step
3, be sure that the Ultrabay Enhanced device eject lever is not popped out and it is housed in its position properly as shown in the figure
a. 3 a 104 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels:
a Windows license label (COA)
b FCC label
c Product label
d FCC or homologation label For some models, you also need to apply one or two FCC labels
c. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. Apply the labels to the base cover as shown in this figure. b a c d ThinkPad Z60m 105 Removing and replacing a FRU 1170 3-1 Digital Media Reader sub card with cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 73 v “1020 Ultrabay Enhanced device” on page 75 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 76 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 v “1150 LCD assembly” on page 100 v “1160 Base cover” on page 103 2 1 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm) When installing: Make sure that the connector
1 is attached firmly. (continued) 106 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 4 3 Step Screw (quantity) Color Torque
3 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm) ThinkPad Z60m 107 Removing and replacing a FRU 1180 USB sub card with cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 73 v “1020 Ultrabay Enhanced device” on page 75 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 76 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 v “1150 LCD assembly” on page 100 v “1160 Base cover” on page 103 1 When installing: Make sure that the connector
1 is attached firmly. (continued) 108 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 3 3 4 2 Step Screw (quantity) Color Torque
3 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) ThinkPad Z60m 109 Removing and replacing a FRU 1190 MG (magnesium) frame For access, remove these FRUs, in order: v “1010 Battery pack” on page 73 v “1020 Ultrabay Enhanced device” on page 75 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 76 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1080 Modem daughter card (MDC-1.5)” on page 85 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 v “1150 LCD assembly” on page 100 v “1160 Base cover” on page 103 v “1170 3-1 Digital Media Reader sub card with cable” on page 106 v “1180 USB sub card with cable” on page 108 110 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU Remove the ac power jack cable
a and the modem cable
b. 4 3 2 1 5 When installing: Make sure the connectors are attached firmly, and that the cables are routed as in the figure above. (continued) ThinkPad Z60m 111 Removing and replacing a FRU Remove the CPU support plate (
c). 6 6 c Step Screw (quantity) Color Torque
6 M2 × 5 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm) (continued) 112 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 8 8 7 7 7 7 7 8 7 9 Step Screw (quantity) Color Torque
7 M2 × 5 mm, flat-head, nylon-coated (6) Black 0.196 Nm (2.0 kgfcm)
8 M2 × 9 mm, flat-head, nylon-coated (3) Black 0.196 Nm (2.0 kgfcm) In step
9, loosen the hex screws. (continued) ThinkPad Z60m 113 Removing and replacing a FRU Remove the system board and the PC Card/ExpressCard slots assembly from the MG frame together, in the direction shown by arrow
10. 10 114 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 1200 System board and PC Card/ExpressCard slots assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 73 v “1020 Ultrabay Enhanced device” on page 75 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 76 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1050 DIMM” on page 81 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1080 Modem daughter card (MDC-1.5)” on page 85 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1130 Fan assembly” on page 95 v “1150 LCD assembly” on page 100 v “1160 Base cover” on page 103 v “1170 3-1 Digital Media Reader sub card with cable” on page 106 v “1180 USB sub card with cable” on page 108 v “1190 MG (magnesium) frame” on page 110 ThinkPad Z60m 115 Removing and replacing a FRU Important notice for handling the system board When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock. v Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. v If a system board is dropped, you must test it, using PC-Doctor for DOS, to make sure that the HDD Active Protection still functions (see below). Note: If the test shows that HDD Active Protection is not functioning, be sure to document the drop in any reject report, and replace the system board. v Avoid rough handling of any kind. v At every point in the process, be sure not to drop or stack the system board. v If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or conductive corrugated material. After replacing the system board, run PC-Doctor for DOS to make sure that HDD Active Protection still functions. The procedure is as follows: 1. Place the computer on a horizontal surface. 2. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Attention: Do not apply physical shock to the computer while the test is running. 116 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
a CPU
b Video chip
c ICH (I/O Controller Hub)
d MCH (Memory ControllerHub)
e Security chip
f Accelerometer chip for the HDD Active Protection System a b d f c e ThinkPad Z60m 117 Removing and replacing a FRU 1 1 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.196 Nm (2.0 kgfcm) Turn over the system board, and then disconnect the PC Card/ExpressCard slots assembly from the system board. 2 When installing: Make sure that the connector of PC Card/ExpressCard slots assembly is attached to the system board firmly. 118 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” 1 1 1 Step Screw cap
1 Screw (quantity) Color Torque M2 × 5 mm, flat-head, nylon-coated (3) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 119 Removing and replacing a FRU In step
3, while sliding the LCD latch lever in the direction shown by the arrow, remove the bezel in the direction shown by arrow
4. 3 2 4 2 2 2 2 2 5 120 MT 2529, 2530, 2531, 2532 2 2 Removing and replacing a FRU 2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” on page 119 1 2 3 When installing: Make sure that connectors
2 and
3 are attached firmly. Cable routing: When replacing the inverter card, route the connector cable as in this figure: ThinkPad Z60m 121 Removing and replacing a FRU 2030 Bluetooth daughter card (BDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” on page 119 1 2 3 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.0 kgfcm) 122 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU When installing: Make sure that connector is attached firmly, and that the card is attached to the guide as in this figure. ThinkPad Z60m 123 Removing and replacing a FRU 2040 Wireless WAN antenna cable (MAIN) For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” on page 119 v “2020 Inverter card” on page 121 v “2030 Bluetooth daughter card (BDC-2)” on page 122 4 2 3 2 1 1 124 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU When installing: In step
2, press the part indicated by the arrow until it snaps into place. 1 1 3 2 4 Note: In step
4, do not tense the cable. To do so, the cable may get damaged by the hinge, and may cause a broken wire. (continued) ThinkPad Z60m 125 Removing and replacing a FRU Cable routing: Route the antenna cable as shown in this figure. 126 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 2050 LCD panel, LCD cable, and hinges For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” on page 119 v “2020 Inverter card” on page 121 v “2030 Bluetooth daughter card (BDC-2)” on page 122 v “2040 Wireless WAN antenna cable (MAIN)” on page 124 2 2 1 1 2 2 1 Step Screw (quantity) Color Torque
1 M2 × 3 mm, flat-head, nylon-coated (3) Black 0.196 Nm (2.0 kgfcm)
2 M2 × 5 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm) (continued) ThinkPad Z60m 127 Removing and replacing a FRU 3a 3b 6 5 4 (continued) 128 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU Remove the hinges (
a) from the LCD panel. a 7 7 8 a 8 7 7 Step Screw (quantity) Color Torque
7 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.196 Nm (2.0 kgfcm) Remove the LCD cable assembly (
b) from the LCD panel. 9 b 10 When installing: When replacing any LCD FRUs, be sure not to pinch the antenna cables. Make sure that the cables are routed as shown in the figures on page 133 and 134. ThinkPad Z60m 129 Removing and replacing a FRU 2060 LCD rear cover and wireless LAN antenna cables For access, remove these FRUs in order: v “1010 Battery pack” on page 73 v “1040 Palm rest or palm rest with fingerprint reader” on page 79 v “1060 Keyboard” on page 82 v “1070 Mini PCI adapter for wireless LAN” on page 84 v “1090 PCI Express Mini card for wireless WAN” on page 87 v “1120 Keyboard bezel and speaker assembly” on page 92 v “1150 LCD assembly” on page 100 v “2010 LCD front bezel” on page 119 v “2020 Inverter card” on page 121 v “2030 Bluetooth daughter card (BDC-2)” on page 122 v “2040 Wireless WAN antenna cable (MAIN)” on page 124 Remove the LCD latches before you remove the antenna cables. 2 1 (continued) 130 MT 2529, 2530, 2531, 2532 Removing and replacing a FRU 3 When installing: Attache the latches as shown in this figure. 4 3 1 2 (continued) ThinkPad Z60m 131 Removing and replacing a FRU 5 5 4 132 4 MT 2529, 2530, 2531, 2532 4 4 Removing and replacing a FRU Cable routing: Route the antenna cables as shown in the following figures. Wireless LAN antenna cable (MAIN: gray) a (continued) ThinkPad Z60m 133 Removing and replacing a FRU Wireless LAN antenna cable (AUX: black) a 134 MT 2529, 2530, 2531, 2532 Locations Locations Front view
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 ThinkLight Status indicators Note: For the description of each indicator, see “Status indicators” on page 50. Wireless WAN antenna Security key hole Universal serial bus (USB) connectors Ultrabay Enhanced status indicator Ultrabay Enhanced latch Ultrabay Enhanced device eject lever Ultrabay Enhanced Video-out connector Fingerprint reader (for some models) TrackPoint buttons Touch pad buttons Touch pad UltraNav TrackPoint pointing stick ThinkVantage button Volume control buttons Power switch ThinkPad Z60m 135 Locations 1 19 2 18 17 16 3 14 13 15 12 9 136 10 11 8 MT 2529, 2530, 2531, 2532 7 6 5 4 Locations Rear view
1
2
3
4
5
6
7
8
9
10
11 Status indicators Note: For the description of each indicator, see “Status indicators” on page 50. PC Card/ExpressCard slots PC Card slot eject button Security key hole Microphone jack Stereo headphone jack RJ-45 (Ethernet) connector RJ-11 (modem) connector External monitor connector AC power connector USB connector 1 2 3 11 4 5 6 10 9 8 7 ThinkPad Z60m 137 Locations Bottom view
1
2
3
4
5
6
7
8
9 Battery pack Battery pack latch Docking connector Infrared port Wireless raido switch LCD cover latch 3-1 Digital Media Reader status indicator 3-1 Digital Media Reader Hard disk drive 1 2 9 3 8 7 6 5 4 138 MT 2529, 2530, 2531, 2532 Parts list Parts list v Each FRU is available for all types or models, unless specific types or models are specified. v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An N in the CRU ID column means the part is not a CRU. A single asterisk (*) means the part is a Tier 1 CRU; two asterisks (**) means the part is a Tier 2 CRU. v FRUs marked with
OP are available as options. v FRUs marked with
R are RoHS compliant. ThinkPad Z60m 139 Parts list Overall 1 25 24 2 23 3 c a 22 21 4 5 6 7 20 8 19 9 10 18 11 12 17 b 13 14 16 15 140 MT 2529, 2530, 2531, 2532 Parts list No. FRU a-c P/N CRU ID See “Miscellaneous parts” on page 171. 1 LCD unit (see “LCD FRUs” on page 160.) 2 Keyboard bezel assembly 26R9588 N 3 Speaker assembly 39T7221 N 4 Modem daughter card (MDC-1.5) 39T0495 ** 5 Wireless WAN antenna cable (MAIN and AUX) v 2529-CTO v 2529-HUx, HWx v 2530-CTO, 36x, 37x v 2531-CTO v 2532-CTO 91P6959 N 6 Intel PRO Wireless 2200BG Mini-PCI Adapter US 27K9932 v 2529-CTO, xxU of 1Hx, E4x, E5x, E7x, E8x, F2x, FFx, FSx, FTx v 2529-xxU of H1x, H2x, HBx, HEx, HLx, R2x, R5x, R6x v 2530-CTO, xxU of 11x, 13x, 14x, 16x, 1Cx, 1Dx, 1Ex, 1Fx, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 21x, 22x, 23x, 24x, 2Ax, 2Cx, 34x, 39x, 42x, 48x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, E4x, F2x v 2531-CTO, xxU of 11x, 13x, 23x, 4Ex, 4Fx, 4Gx, 4Jx, 62x, 6Cx, 77x, 7Ax v 2532-CTO, xxU of 11x, 62x, 77x ** ROW 27K9934 v 2529-CTO, 1Hx, E4x, E5x, E7x, E8x, F2x, FFx, FSx, FTx except xxU v 2529-H1x, H2x, HBx, HEx, HLx, R2x, R5x, R6x except xxU v 2530-CTO, xxU of 11x, 13x, 14x, 16x, 1Cx, 1Dx, 1Ex, 1Fx, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 21x, 22x, 23x, 24x, 2Ax, 2Cx, 34x, 39x, 42x, 48x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, E4x, F2x except xxU v 2531-CTO, xxU of 11x, 13x, 23x, 4Ex, 4Fx, 4Gx, 4Jx, 62x, 6Cx, 77x, 7Ax except xxU v 2532-CTO, xxU of 11x, 62x, 77x except xxU ** (continued) ThinkPad Z60m 141 Parts list No. FRU 6 P/N Intel PRO Wireless 2915ABG Mini-PCI Adapter US 27K9936 v 2529-CTO, xxU of E1x, E2x, E3x, E6x, E9x, EAx, EBx, F1x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx v 2529-xxU of H4x, H5x, H6x, H7x, H8x, H9x, HAx, HCx, HDx, HFx, HGx, HHx, HJx, HKx, HSx, HTx, R3x, R7x, 8x, R9x, RAx, RBx, RCx v 2530-CTO, xxU of 18x, 19x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Ex, 31x, 35x, 36x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Lx, 4Mx, 4Nx, 4Px, E9x, EBx v 2530-xxU of J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JRx, JSx, JTx, JVx, K1x, K2x, K5x, K7x, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, xxU of 3Jx, 3Kx, 49x, 4Qx, 68x, 6Ax, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 78x, 79x, E1x, E9x v 2531-xxU of M1x, M2x, M3x, M4x, M5x, M6x, M7x, M9x, MAx, MBx, MCx, MGx, MJx, MKx, MTx, R7x, RAx, RBx v 2532-CTO, xxU of 3Jx, 6Dx, E9x v 2532-xxU of M1x, M9x, MCx, MTx (continued) 142 CRU ID MT 2529, 2530, 2531, 2532 ** Parts list No. FRU 6 P/N CRU ID Intel PRO Wireless 2915ABG Mini-PCI Adapter EU 27K9938 v 2529-CTO, xxG of E1x, E2x, E3x, E6x, E9x, EAx, EBx, F1x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx v 2529-xxG of H4x, H5x, H6x, H7x, H8x, H9x, HAx, HCx, HDx, HFx, HGx, HHx, HJx, HKx, HSx, HTx, R3x, R7x, 8x, R9x, RAx, RBx, RCx v 2530-CTO, xxG of 18x, 19x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Ex, 31x, 35x, 36x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Lx, 4Mx, 4Nx, 4Px, E9x, EBx v 2530-xxG of J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JRx, JSx, JTx, JVx, K1x, K2x, K5x, K7x, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, xxG of 3Jx, 3Kx, 49x, 4Qx, 68x, 6Ax, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 78x, 79x, E1x, E9x v 2531-xxG of M1x, M2x, M3x, M4x, M5x, M6x, M7x, M9x, MAx, MBx, MCx, MGx, MJx, MKx, MTx, R7x, RAx, RBx v 2532-CTO, xxG of 3Jx, 6Dx, E9x v 2532-xxG of M1x, M9x, MCx, MTx ** (continued) ThinkPad Z60m 143 Parts list No. FRU 6 P/N Intel PRO Wireless 2915ABG Mini-PCI Adapter Japan 39T5643 v 2529-CTO, xxJ xxE of E1x, E2x, E3x, E6x, E9x, EAx, EBx, F1x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx v 2529-xxJ xxE of H4x, H5x, H6x, H7x, H8x, H9x, HAx, HCx, HDx, HFx, HGx, HHx, HJx, HKx, HSx, HTx, R3x, R7x, 8x, R9x, RAx, RBx, RCx v 2530-CTO, xxJ xxE of 18x, 19x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Ex, 31x, 35x, 36x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Lx, 4Mx, 4Nx, 4Px, E9x, EBx v 2530-xxJ xxE of J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JRx, JSx, JTx, JVx, K1x, K2x, K5x, K7x, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, xxJ xxE of 3Jx, 3Kx, 49x, 4Qx, 68x, 6Ax, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 78x, 79x, E1x, E9x v 2531-xxJ xxE of M1x, M2x, M3x, M4x, M5x, M6x, M7x, M9x, MAx, MBx, MCx, MGx, MJx, MKx, MTx, R7x, RAx, RBx v 2532-CTO, xxJ xxE of 3Jx, 6Dx, E9x v 2532-xxJ xxE of M1x, M9x, MCx, MTx (continued) 144 CRU ID MT 2529, 2530, 2531, 2532 ** Parts list No. FRU 6 P/N CRU ID Intel PRO Wireless 2915ABG Mini-PCI Adapter Hebrew 27K9942 v 2529-CTO, xxC, xxK, xxL, xxP, xxS, xxV, xxY of E1x, E2x, E3x, E6x, E9x, EAx, EBx, F1x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx v 2529-xxC, xxK, xxL, xxP, xxS, xxV, xxY of H4x, H5x, H6x, H7x, H8x, H9x, HAx, HCx, HDx, HFx, HGx, HHx, HJx, HKx, HSx, HTx, R3x, R7x, 8x, R9x, RAx, RBx, RCx v 2530-CTO, xxC, xxK, xxL, xxP, xxS, xxV, xxY of of 18x, 19x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Ex, 31x, 35x, 36x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Lx, 4Mx, 4Nx, 4Px, E9x, EBx v 2530-xxC, xxK, xxL, xxP, xxS, xxV, xxY of J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JRx, JSx, JTx, JVx, K1x, K2x, K5x, K7x, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, xxC, xxK, xxL, xxP, xxS, xxV, xxY of of 3Jx, 3Kx, 49x, 4Qx, 68x, 6Ax, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 78x, 79x, E1x, E9x v 2531-xxC, xxK, xxL, xxP, xxS, xxV, xxY of M1x, M2x, M3x, M4x, M5x, M6x, M7x, M9x, MAx, MBx, MCx, MGx, MJx, MKx, MTx, R7x, RAx, RBx v 2532-CTO, xxC, xxK, xxL, xxP, xxS, xxV, xxY of of 3Jx, 6Dx, E9x v 2532-xxC, xxK, xxL, xxP, xxS, xxV, xxY of M1x, M9x, MCx, MTx ** (continued) ThinkPad Z60m 145 Parts list No. FRU 6 CRU ID ThinkPad 11a/b/g Wireless LAN Mini PCI Adapter II US v 2529-CTO v 2529-xxU, xxF, xxL, xxS, xxM, xxB, xxH of H3x, HMx, HNx, HPx, HQx, HRx, HUx, HWx v 2530-CTO, xxU, xxF, xxL, xxS, xxM, xxB, xxH of 37x, 38x, 3Bx, 4Cx v 2530-xxU, xxF, xxL, xxS, xxM, xxB, xxH of K3x, K4x, K6x v 2531-CTO, xxU, xxF, xxL, xxS, xxM, xxB, xxH of 38x v 2531-xxU, xxF, xxL, xxS, xxM, xxB, xxH of M8x, MDx, MSx, MUx v 2532-CTO, xxU, xxF, xxL, xxS, xxM, xxB, xxH of 38x v 2532-xxU, xxF, xxL, xxS, xxM, xxB, xxH of MDx, MSx, MUx 39T0355 ** EU 39T0357 v 2529-CTO v 2529-xxP, xxY, xxG, xxA, xxC, xxK of H3x, HMx, HNx, HPx, HQx, HRx, HUx, HWx v 2530-CTO, xxP, xxY, xxG, xxA, xxC, xxK of 37x, 38x, 3Bx, 4Cx v 2530-xxP, xxY, xxG, xxA, xxC, xxK of K3x, K4x, K6x v 2531-CTO, xxP, xxY, xxG, xxA, xxC, xxK of 38x v 2531-xxP, xxY, xxG, xxA, xxC, xxK of M8x, MDx, MSx, MUx v 2532-CTO, xxP, xxY, xxG, xxA, xxC, xxK of 38x v 2532-xxP, xxY, xxG, xxA, xxC, xxK of MDx, MSx, MUx ** Japan v 2529-CTO v 2529-xxE, xxJ of H3x, HMx, HNx, HPx, HQx, HRx, HUx, HWx v 2530-CTO, xxE, xxJ of 37x, 38x, 3Bx, 4Cx v 2530-xxE, xxJ of K3x, K4x, K6x v 2531-CTO, xxE, xxJ of 38x v 2531-xxE, xxJ of M8x, MDx, MSx, MUx v 2532-CTO, xxE, xxJ of 38x v 2532-xxE, xxJ of MDx, MSx, MUx ** (continued) 146 P/N MT 2529, 2530, 2531, 2532 39T5645 Parts list No. FRU 6 P/N CRU ID ThinkPad 11a/b/g Wireless LAN Mini PCI Adapter II Taiwan v 2529-CTO v 2529-xxV of H3x, HMx, HNx, HPx, HQx, HRx, HUx, HWx v 2530-CTO, xxV of 37x, 38x, 3Bx, 4Cx v 2530-xxV of K3x, K4x, K6x v 2531-CTO, xxV of 38x v 2531-xxV of M8x, MDx, MSx, MUx v 2532-CTO, xxV of 38x v 2532-xxV of MDx, MSx, MUx 27K9999 ** 7 Magnesium frame 41V9799 N 8 USB sub card with cable 39T5632 N 9 Backup battery 92P1161 ** 10 S-Video 3-1 sub card with cable 41W1310 N 11 Hard disk drive rubber rails 41V9756 * 12 Hard disk drive, 40 GB, 9.5 mm, 5,400 rpm v 2529-CTO, E1x, E3x, E4x, E5x, F1x, F2x, F3x, F4x, F5x v 2529-H2x, H6x, HMx, R2x, R6x v 2530-CTO, 11x, 14x, 16x, 18x, 1Kx, 1Mx, 1Nx, 1Yx, 1Zx, 22x, 2Ax, 2Bx, 2Dx, 2Gx, 2Hx, 32x, 33x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ex, E4x, F2x v 2530-JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, K7x v 2531-CTO, 11x, 4Ex, 4Qx, 68x, 6Cx, 6Dx, 6Ex, 77x, E1x v 2532-CTO, 11x, 6Dx, 77x HGST 39T2621 * Toshiba 39T2629 * Hard disk drive, 60 GB, 9.5 mm, 5,400 rpm v 2529-CTO, E2x, E6x, E7x, F7x, FFx v 2529-R5x, R7x, R9x, RAx, RBx v 2530-CTO, 13x, 19x, 1Cx, 1Dx, 1Ex, 1Fx, 1Gx, 21x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Cx, 2Ex, 31x, 34x, 3Bx, 3Rx, 3S, 42x, 48x, 4Fx, 4Hx, 4Jx, 4Nx, 4Px v 2530-J9x, JAx, JSx, K5x, K6x, K8x, K9x, KAx, KBx, R7x v 2531-CTO, 13x, 23x, 4Fx, 4Jx, 62x, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 78x, 79x, 7Ax v 2531-M1x, M2x, M4x, MGx, MJx, MKx, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 62x v 2531-M1x, MSx, MUx HGST 39T2623 * Toshiba 39T2631 * (continued) ThinkPad Z60m 147 Parts list No. FRU 12 P/N CRU ID Hard disk drive, 80 GB, 9.5 mm, 5,400 rpm v 2529-CTO, 1Hx, E8x, E9x, EBx, F6x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FMx, FQx, FRx, FSx v 2529-H5x, H7x, H8x, HAx, HBx, HCx, HDx, HEx, HFx, HNx, HPx, HSx, HTx, R3x, R8x v 2530-CTO, 1Hx, 35x, 36x, 37x, 3Jx, 3Mx, 3Nx, 3Px, 3Qx, 43x, 47x, 49x, 4Ax, 4Dx, 4Gx, 4Lx, 4Mx, E9x, EBx v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, JTx, K1x, K3x, R8x v 2531-CTO, 3Jx, 49x, 4Gx, 6Ax, 71x, 76x, E9x v 2531-M3x, M5x, M9x, MAx, MBx, MDx v 2532-CTO, 3Jx, E9x v 2532-M9x, MDx HGST 39T2625 * Toshiba 39T2633 * Hard disk drive, 100 GB, 9.5 mm, 5,400 rpm v 2529-CTO, EAx, FJx, FKx, FLx, FPx, FTx v 2529-H1x, H3x, H9x v 2530-CTO, 1Jx, 38x, 3Kx, 44x, 46x, 4Bx, 4Cx v 2530-J8x, JVx, K2x, K4x v 2531-CTO, 38x, 3Kx v 2531-M6x, MTx v 2532-CTO, 38x v 2532-MTx HGST 39T2627 * Toshiba 39T2635 * Hard disk drive, 100 GB, 9.5 mm, 7,200 rpm v 2529-CTO, H4x, HGx, HHx, HJx, HKx, HLx, HQx, HRx, HUx, HWx, RCx v 2530-CTO v 2531-CTO, M7x, M8x, MCx v 2532-CTO, MCx HGST 27R2345 * Seagate 27R2346 * (continued) 148 MT 2529, 2530, 2531, 2532 Parts list No. FRU 13 P/N CRU ID Battery pack, Li-ion (6 cell) v 2529-CTO, 1Hx, E1x, E2x, E3x, E4x, E5x, E6x, E7x, E8x, EBx, Fxx v 2529-H1x, H2x, H3x, H6x, H7x, H8x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HMx, HRx, HWx, HSx, HTx, R2x, R3x, R5x, R6x, R7x, R8x, R9x, RAx, RBx v 2530-CTO, 1xx, 2xx, 31x, 32x, 33x, 39x, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, E4x, EBx, F2x, 5xx v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, JSx, K5x, K6x, K7x, K8x, K9x, KAx, KBx, R7x, R8x, v 2531-CTO, 1xx, 2xx, 3Jx, 4Ex, 4Fx, 4Gx, 4Jx, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 77x, 78x, 79x, 7Ax, E1x v 2531-M1x, M2,x M3x, M4x, M9x, MAx, MBx, MCx, MGx, MJx, MKx, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 1xx, 3Jx, 6x, 6Dx, 77x v 2532-M1x, M9x, MCx, MSx, MUx Sanyo 92P1127 * Panasonic 92P1129 * Battery pack, Li-ion (9 cell) v 2529-CTO, E9x, EAx v 2529-H4x, H5x, H9x, HNx, HPx, HQx, HUx, RCx v 2530-CTO, 34x, 35x, 36x, 37x, 38x, 3Kx, 3Mx, 3Nx, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, E9x v 2530-JTx, JVx, K1x, K2x, K3x, K4x v 2531-CTO, 38x, 49x, 3Kx, 71x, 76x, E9x v 2531-M5x, M6x, M7x, M8x, MDx, MTx v 2532-CTO, 38x, E9x v 2532-MDx, MTx Sanyo 92P1131 * Panasonic 92P1133 * (continued) ThinkPad Z60m 149 Parts list No. FRU P/N CRU ID 14 39T2661 * MKE (SR-8178) 39T2663 * HLDS (GDR-8084N) 39T2665 * CD-ROM drive, 12.7 mm, TEAC (CD-244EN) v 2529-CTO v 2530-CTO v 2530-JQx v 2531-CTO v 2532-CTO DVD drive, 12.7 mm v 2529-CTO, E4x, E5x v 2530-CTO, 1Yx, 1Zx, E4x v 2530-JPx v 2531-CTO v 2532-CTO DVD/CD-RW combo drive, 12.7 mm v 2529-CTO, E1x, E3x, E7x, F1x, F2x, F3x, F4x, F5x, F7x, F8x, FAx, FMx, FPx, FSx v 2529-H2x, H6x, HMx, R2x, R6x, R7x, R9x, RAx, RBx v 2530-CTO, 11x, 13x, 14x, 1Cx, 1Dx, 1Ex, 1Gx, 1Kx, 1Mx, 1Nx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Gx, 2Hx, 31x, 32x, 33x, 35x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 47x, 4Ax, 4Ex, 4Gx, 4Hx, 4Jx, F2x v 2530-J9x, JAx, JMx, JNx, K1x, K2x, K3x, K4x, K5x, K6x, K7x, R7x v 2531-CTO, 11x, 13x, 23x, 4Ex, 4Gx, 4Jx, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 6Jx, 77x, E1x v 2531-M1x, M2x, M3x, M9x, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 11x, 62x, 6Dx, 77x v 2532-M1x, M9x, MSx, MUx PCC (UJDA770) 39T2667 * HLDS (GCC-4244N) 39T2669 * DVD-RAM/RW drive, 12.7 mm v 2529-CTO, 1Hx, E2x, E6x, E8x, E9x, EAx, EBx, F6x, F9x, FBx, FCx, FEx, FFx, FGx, FHx, FJx, FKx, FLx, FQx, FRx, FTx v 2530-CTO, 16x, 18x, 19x, 1Hx, 1Jx, 2Ax, 2Cx, 2Dx, 2Ex, 34x, 36x, 37x, 38x, 3Bx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 44x, 46x, 49x, 4Bx, 4Cx, 4Dx, 4Fx, 4Lx, 4Mx, 4Nx, 4Px, E9x, EBx v 2531-CTO, 38x, 3Jx, 3Kx, 49x, 4Fx, 6Gx, 71x, 75x, 76x, 78x, 79x, 7Ax, E9x v 2532-CTO, 38x, 3Jx, E9x PCC (UJ-830Z) 39T2671 * HLDS (GSA-4080A) 39T2673 * (continued) 150 MT 2529, 2530, 2531, 2532 Parts list No. FRU 14 P/N CRU ID DVD-RAM/RW drive, 12.7 mm v 2529-H1x, H3x, H4x, H5x, H7x. H8x, H9x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HNx, HPx, HQx, HRx, HUx, HWx, HSx, HTx, R3x, R5x, R8x, RCx v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, JBx, JDx, JE,x JFx, JGx, JHx, JKx, JLx. JRx, JSx, JTx, JVx, K7x, K8x, K9x, KAx, KBx, R8x v 2531-M4x, M5x, M6x, M7x, M8x, MAx, MBx, MCx, MDx, MGx, MJx, MKx, MTx v 2532-MCx, MDx, MTx PCC (UJ-850) 27R2343 * HLDS (GSA-4082) 27R2344 * 13N5354 * 26R9594 * WW v 2529-all except xxV 26R9596 N Taiwan v 2529-CTO, xxV 26R9600 N WW v 2530-all except xxV 26R9597 N Taiwan v 2530-CTO, xxV 26R9601 N WW v 2531-all except xxV 26R9598 N Taiwan v 2531-CTO, xxV 26R9602 N WW v 2532-all except xxV 26R9599 N Taiwan v 2532-CTO, xxV 26R9603 N Travel cover v 2529-CTO, v 2530-CTO, v 2531-CTO, v 2532-CTO, xxJ xxJ xxJ xxJ 15 Hard disk drive cover 16 Base cover for 2529 Base cover for 2530 Base cover for 2531 Base cover for 2532 (continued) ThinkPad Z60m 151 Parts list No. FRU P/N CRU ID 17 73P3841 ** 512-MB DDR2-533 SDRAM SO-DIMM 73P3843 (PC2-4200) card
R v 2529-CTO, 1Hx, E2x, E3x, E5x, E6x, E7x, E8x, E9x, F6x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FFx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx, FSx, FTx v 2529-H1x, H3x, H4x, H5x, H6x, H7x, H8x, H9x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HMx, HNx, HPx, HQx, HRx, HUx, HWx, HS,x HTx, R3x, R5x, R7x, R8x, R9x, RAx, RBx v 2530-CTO 11x, 16x, 18x, 19x, 1Cx, 1Ex, 1Fx, 1Hx, 1Jx, 1Nx, 21x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 31x, 34x, 35x, 39x, 3Bx, 3Jx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 46x, 47x, 48x, 49x, 4Ax, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, E9x v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JR,x JSx, JTx, K1x, K2x, K3x, K4x, K5x, K6x, K7x, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, 11x, 3Jx, 49x, 4Ex, 4Fx, Gx, 4Jx, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 77x, 78x, 79x, 7Ax, E1x, E9x v 2531-M1x, M2x, M3x, M4x, M5x, M9x, MAx, MBx, MCx, MDx, MGx, MJx, MKx, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 11x, 3Jx, 6Dx, 77x, E9x v 2532-M1x, M9x, MCx, MDx, MSx, MUx ** 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card
R v 2529-CTO, E1x, E4x, F1x, F2x, F3x, F4x, F5x v 2529-H2x, R2x, R6x, v 2530-CTO 13x, 14x, 1Dx, 1Gx, 1Kx, 1Mx, 1Yx, 1Zx, 22x, 23x, 24x, 2Gx, 2Hx, 32x, 33x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 46x, E4x, F2x v 2530-JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, v 2531-CTO, 13x, 23x, 4Qx, 62x, E1x v 2532-CTO, 62x (continued) 152 MT 2529, 2530, 2531, 2532 Parts list No. FRU P/N CRU ID 17 1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card
R v 2529-CTO, EAx, EBx v 2529-RCx v 2530-CTO 36x, 37x, 38x, 3Kx, 44x, 4Bx, 4Cx, EBx v 2530-JVx v 2531-CTO, 38x, 3Kx v 2531-M6x, M7x, M8x, MTx v 2532-CTO, 38x v 2532-MTx 73P3845 ** 18 System board assembly with 915GM, 42T0000 integrated v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, G1x, G2x, G3x, G4x, G5x v 2529-H2x, H3x, H6x, HAx, HBx, HCx, HMx, HNx, HPx, HSx, P1x, P2x, P6x, P7x, P8x, P9x, R2x, R5x, R6x, R7x, R8x, RBx v 2530-CTO, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Ex, 1Fx, 1Yx, 1Zx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 3Bx, 3Cx, 51x, 52x, 57x, E4x, F2x v 2530-J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, JSx, K5x, K6x, K7x, K8x, K9x, KA,x KBx, LBx, LCx, LDx, R7x, R8x v 2531-CTO, 13x, 23x, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, E1x v 2531-M1x, M3x, MAx, MDx, MGx, R7x, RBx v 2532-CTO, 62x, 6Dx v 2532-M1x, MDx N (continued) ThinkPad Z60m 153 Parts list No. FRU 18 P/N CRU ID System board assembly with 915PM, M22-64 v 2529-CTO, 1Hx, E7x, E8x, F8x, F9x, FAx, FBx, FCx, FEx, FFx, FMx, FPx, FQx, FRx, FSx, G6x, G7x, G8x, G9x v 2529-H1x, H7x, H8x, HDx, HEx, HFx, HTx, L2x, P3x, R9x, RAx v 2530-CTO, 11x, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Bx, 2Cx, 2Ex, 34x, 39x, 3Dx, 3Ex, 3Jx, 3Mx, 42x, 47x, 48x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 55x, 56x, 5Ax, 5Bx v 2530-J3x, J4x, JTx, JVx, K1x, K2x, K3x, K4x, L2x, L4x. L7x, LAx v 2531-CTO, 11x, 3Jx, 4Ex, 4Fx, 4Gx, 4Jx, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 77x, 78x, 79x, 7Ax v 2531-M2x, M4x, M9x, MJx, MKx, MUx, RAx v 2532-CTO, 11x, 3Jx, 77x v 2532-M9x, MUx Hynix 42T0006 N Samsung 42T0008 N System board assembly with 915PM, M24-128 v 2529-CTO, E9x, EAx, EBx, FGx, FHx, FJx, FKx, FLx, FTx, v 2529-H4x, H5x, H9x, HGx, HHx, HJx, HKx, HLx, HQx, HRx, HUx, HWx, R3x, RCx v 2530-CTO, GAx, GBx, GCx, 2Ax, 35x, 36x, 37x, 38x, 3Fx, 3Gx, 3Hx, 3Kx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 49x, 4Ax, 4Bx, 4Cx, 53x, 54x, 58x, 59x, E9x, EBx v 2530-J1x, J2x, J5x, J6x, J7x, J8x, L1x, L3x, L5x, L6x, L8x, L9x v 2531-CTO, 38x, 3Kx, 49x, 71x, 76x, E9x v 2531-M5x, M6x, M7x, M8x, MBx, MCx, MTx v 2532-CTO, 38x, E9x v 2532-MCx, MTx Hynix 42T0002 N Samsung 42T0004 N 19 PC Card/ExpressCard slots assembly 26R9585 N 20 CPU assembly, Intel Celeron M processor 360 (1.4 GHz) v 2529-CTO, E1x, E2x, E4x, E5x, F1x, F2x, FQx, G1x v 2530-CTO, 14x, 16x, 1Cx, 1Yx, 27x, 28x, 29x, 2x, 2Hx, 31x, 32x, 33x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 57x, E4x, F2x v 2531-CTO, E1x v 2532-CTO 39T5385 N (continued) 154 MT 2529, 2530, 2531, 2532 Parts list No. FRU P/N CRU ID 20 CPU assembly, Intel Celeron M processor 370 (1.5 GHz) v 2529-CTO, F3x, F4x, FRx v 2529-H6x, P1x v 2530-CTO, 18x, 1Dx, 1Ex, 2Dx, 3Bx, 52x v 2530-J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, K8x, K9x, KAx, KBx, LBx, LCx. LDx v 2531-CTO v 2532-CTO 39T0331 N CPU assembly, Intel Celeron M processor 380 (1.6 GHz) v 2529-CTO, H2x, H7x, HMx, HSx, R2x, R5x, R6x, P2x v 2530-CTO, JRx, K5x, K6x, K7x v 2531-CTO v 2532-CTO 39T5686 N CPU assembly, Intel Pentium M processor 740 (1.73 GHz) v 2529-CTO, E3x, E4x, F5x, F6x, FFx, G2x, G6x v 2529-HTx, P6x v 2530-CTO, 11x, 13x, 1Fx, 1Gx, 1Kx, 1Mx, 1Nx, 1Zx, 22x, 23x, 24x, 25x, 26x, 2Bx, 39x, 47x, 49x, 4Dx, 4Ex, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 51x, 53x, 54x, 55x, 56x v 2530-J3x, J4x, K1x, L3x, L4x. L8x, L9x, LAx v 2531-CTO, 11x, 13x, 23x, 49x, 4Ex, 4Jx, 4Qx, 62x, 68x, 6Cx, 6Fx, 6Jx, 75x, 77x, 7Ax v 2531-M1x v 2532-CTO, 11x, 62x, 77x v 2532-M1x, 39T0046 N (continued) ThinkPad Z60m 155 Parts list No. FRU P/N CRU ID 20 CPU assembly, Intel Pentium M processor 750 (1.86 GHz) v 2529-CTO, 1Hx, E7x, E8x, F7x, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FMx, FSx, G3x, G7x, GAx v 2529-H8x, HAx, HBx, HCx, HFx, R3x, R7x, R8x, R9x, RAx, RBx, P3x, P7x v 2530-CTO, 19x, 1Hx, 1Jx, 21x, 2Ax, 2Cx, 2Ex, 34x, 35x, 3Mx, 3Nx, 42x, 48x, 4Ax, 4Bx, 4Fx, 4Gx v 2530-J5x, J7x, K2x, K4x, R7x, R8x v 2531-CTO, 4Fx, 4Gx, 6Ax, 6Dx, 6Gx, 6Hx, 76x, 78x, 79x v 2531-M3x, M9x, MDx, MGx, MJx, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 6Dx v 2532-M9x, MDx, MSx, MUx 39T0047 N CPU assembly, Intel Pentium M processor 760 (2.0 GHz) v 2529-CTO, E9x, EAx, EBx, FJx, FKx, FPx, FTx, G4x, G8x, GBx v 2529-H3x, HDx, HEx, HJx, HKx, HLx, HNx, HPx, L2x, P8x v 2530-CTO, 36x, 37x, 38x, 3Jx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 4Cx, 58x, 59x, 5Ax, 5Bx, E9x, EBx v 2530-J1x, J2x, J6x, J8x, JSx, L1x, L2x, L5x, L6x, L7x v 2531-CTO, 38x, 3Jx, 6Ex, 71x, E9x v 2531-M2x, M4x, MAx, MKx, MTx v 2532-CTO, 38x, 3Jx, E9x v 2532-MTx 39T0048 N CPU assembly, Intel Pentium M processor 770 (2.13 GHz) v 2529-CTO, FLx, G5x, G9x, GCx v 2529-H1x, H4x, H5x, H9x, HGx, HHx, HQx, HRx, HUx, HWx, P9x, RCx v 2530-CTO, 3Kx v 2531-CTO, 3Kx v 2531-MBx, MCx v 2532-CTO v 2532-MCx 39T0049 N CPU assembly, Intel Pentium M processor 780 (2.26 GHz) v 2529-CTO v 2530-CTO, JTx, JVx v 2531-CTO, M5x, M6x, M7x, M8x v 2532-CTO 39T0460 N (continued) 156 MT 2529, 2530, 2531, 2532 Parts list No. FRU 21 P/N CRU ID Fan and thermal device, without graphic 26R9586 v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, G1x, G2x, G3x, G4x, G5x v 2529v 2530-CTO, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Ex, 1Fx, 1Yx, 1Zx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 3Bx, 3Cx, 51x, 52x,57x, E4x, F2x v 2530v 2531-CTO, 13x, 23x, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, E1x v 2531v 2532-CTO, 62x, 6Dx v 2532- N Fan and thermal device, with graphic v 2529-CTO, 1Hx, E7x, E8x, E9x, EAx, EBx, F8x, F9x, FAx, FBx, FCx, FEx, FFx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FQx, FRx, FSx, FTx, G6x, G7x, G8x, G9x, GAx, GBx, GCx v 2529v 2530-CTO, 11x, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Ax, 2Bx, 2Cx, 2Ex, 34x, 35x, 36x, 37x, 38x, 39x, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 53x, 54x, 55x, 56x, 58x, 59x, 5Ax, 5Bx, E9x, EBx v 2530v 2531-CTO, 11x, 38x, 3Jx, 3Kx, 49x, 4Ex, 4Fx, 4Gx, 4Jx, 6Fx, 6Gx, 6Hx, 6Jx, 71x, 75x, 76x, 77x, 78x, 79x, 7Ax, E9x v 2531v 2532-CTO, 11x, 38x, 3Jx, 77x, E9x v 2532- N 26R9587 (continued) ThinkPad Z60m 157 Parts list No. FRU P/N CRU ID 22 Sierra Wireless EV-DO Wireless WAN Mini PCI Express Adapter v 2529-CTO v 2529-HUx, HWx v 2530-CTO, 36x, 37x v 2531-CTO v 2532-CTO 39T5664 N 23 Palm rest assembly without fingerprint 26R9589 reader v 2529-CTO, E1x, E2x, E3x, E4x, E5x, F1x, F2x, F3x, F4x, F5x, F7x, FQx, G1x v 2529-H2x, H3x, H6x, HMx, HNx, R2x, R5x, R6x, R7x, R8x, R9x, RAx, RBx, P1x, v 2530-CTO, 11x, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Ex, 1Kx, 1Mx, 1Yx, 1Zx, 21x, 22x, 23x, 2Bx, 2Dx, 32x, 33x, 34x, 35x, 3Bx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, E4x, F2x v 2530-J5x, J7x, J8x, JPx, JQx, K7x, R7x, R8x v 2531-CTO, 11x, 13x, 23x, 4Ex, 4Fx, 4Gx, 4Jx, 4Qx, 6Fx, 6Gx, 77x, E1x v 2531-M3x, MJx, MKx, MSx, MUx, R7x, RAx, RBx v 2532-CTO, 11x, 77x v 2532-MSx, MUx ** (continued) 158 MT 2529, 2530, 2531, 2532 Parts list No. FRU P/N 23 Palm rest assembly with fingerprint 26R9591 reader v 2529-CTO, 1Hx, E6x, E7x, E8x, E9x, EAx, EBx, F6x, F8x, F9x, FAx, FBx, FCx, FEx, FFx, FGx, FHx, FJx, FKx, FLx, FMx, FPx, FRx, FSx, FTx, G2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x, GAx, GBx, GCx v 2529-H1x, H4x, H5x, H7x, H8x, H9x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HPx, HQx, HRx, HUx, HWx, HSx, HTx, R3x, RCx, P2x, P3x, P6x, P7x, P8x, P9x, L3x, v 2530-CTO, 1Fx, 1Gx, 1Hx, 1Jx, 1Nx, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Ex, 2Gx, 2Hx, 31x, 36x, 37x, 38x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Lx, 4Mx, 4Nx, 4Px, 5xx, E9x, EBx v 2530-J1x, J2x, J3x, J4x, J6x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JRx, JSx, JTx, JVx, K1x, K2x, K3x, K4x, K5x, K6x, K8x, K9x, KAx, KBx, Lxx, v 2531-CTO, 38x, 3Jx, 3Kx, 49x, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Hx, 6Jx, 71x, 75x, 76x, 78x, 79x, 7Ax, E9x v 2531-M1x, M2x, M4x, M5x, M6x, M7x, M8x, M9x, MAx, MBx, MCx, MDx, MGx, MTx v 2532-CTO, 38x, 3Jx, 62x, 6Dx, E9x v 2532-M1x, M9x, MCx, MDx, MTx 24 Keyboard (see “Keyboard” on page 166) 25 Track point stick caps 91P9642 ThinkPad Z60m CRU ID ** * 159 Parts list LCD FRUs 1 10 2 9 8 3 4 7 5 a b c d e 6 160 MT 2529, 2530, 2531, 2532 Parts list No. FRU a-d P/N CRU ID 41V9410 N See “Miscellaneous parts” on page 171. 1 LCD front bezel 2 LCD panel, 15.4-in. WXGA v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, E7x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FMx, FPx, FQx, FRx, FSx, G1x, g2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x v 2529-H2x, H3x, H5x, H6x, H7x, H8x, HBx, HMx, HNx, HPx, HQx, HRx, HUx, HWx, HSx, P1x, P2x, P6x, P7x, P8x, P9x, R2x, R5x, R6x, R7x, R8x, RAx, RBx v 2530-CTO, 11x, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Yx, 1Zx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 34x, 35x, 36x, 37x, 39x, 3Bx, 3Dx, 3Fx, 42x, 47x, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, E4x, F2x v 2530-J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, JSx, LCx, LDx v 2531-CTO, 11x, 13x, 23x, 4Ex, 4Fx, 4Gx, 4Jx, 4Qx, 62x, 6Ax, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 77x, 78x, 7Ax, E1x v 2531-K5x, K6x, K7x, K8x, K9x, KAx, KBx, M1x, M2x, M3x, M9x, MAx, MCx, MDx, MGx, MSx, MUx, R7x, R8x, RAx, RBx v 2532-CTO, 11x, 62x, 77x v 2532-M1x, M9x, MDx, MSx, MUx Samsung 13N7016 N LG 13N7014 N 13N7018 N LCD panel, 15.4-in. WXGA bright, ID Tech v 2529-CTO, 1Hx, EBx, FAx, FBx, FCx, FEx, FLx v 2529-H1x, H4x, H9x, HDx, HEx, HFx, HTx, L2x, P3x, R3x, R9x, RCx v 2530-CTO, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Ex, 38x, 3Ex, 3Gx, 3Jx, 3Kx, 3Mx, 3Nx, 44x, 4Dx, 54x, 56x, 59x, 5Bx, EBx v 2530-JTx, JVx, K1x, K2x, K3x, K4x, L1x, L2x, L3x, L4x v 2531-CTO, 38x, 3Jx, 3Kx v 2531-M5x, M6x v 2532-CTO, 38x, 3Jx v 2532-MCx (continued) ThinkPad Z60m 161 Parts list No. FRU P/N CRU ID 2 LCD panel, 15.4-in. WSXGA+, LG 13N7020 v 2529-CTO, E8x, E9x, EAx, FFx, FGx, FHx, FJx, FKx, FTx, GAx, GBx, GCx v 2529-HAx, HCx, HGx, HHx, HJx, HKx, HLx v 2530-CTO, 1Ex, 1Fx, 2Ax, 2Cx, 3Cx, 3Hx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 46x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Lx, 4Mx, 4Nx, 4Px, 51x, 52x, 53x, 55x, 57x, 58x, 5Ax, E9x v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x v 2531-CTO, 49x, 68x, 6Cx, 6Dx, 6Ex, 71x, 76x, 79x, E9x v 2531-M4x, M7x, M8x, MBx, MJx, MKx, MTx v 2532-CTO, 6Dx, E9x v 2532-MTx N 3 Hinge, black 26R9583 v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, E7x, E8x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FFx, FMx, FPx, FQx, FRx, FSx, G1x, G2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x v 2529-H2x, H3x, H5x, H6x, H7x, H8x, HAx, HBx, HCx, HMx, HNx, HPx. HQx, HRx, HUx, HWx, P1x, P2x, R2x, R5x, RAx, RBx v 2530-CTO, 11x, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Ex, 1Fx, 1Yx, 1Zx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Cx, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 34x, 35x, 36x, 37x, 39x, 3Bx, 3Cx, 3Dx, 3Fx, 3Hx, 42x, 47x, 48x, 49x, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 51x, 52x, 53x, 55x, 57x, 5AxE4x, F2x v 2530-J3x, J4x, J5x, J6x, J9x, JAx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, JSx, K5x, K6x, K7x, KAx, KBx, L6x, L7x, L9x, LAx, LBx, LDx v 2531-CTO, 11x, 13x, 23x, 49x, 4Ex, 4Fx, 4Gx, 4Jx, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 77x, 78x, 79x, 7Ax, E1x v 2531-M1x, M2x, M3x, M4x, M9x, MDx, MGx, MJx, MKx, MSx, MTx, MUx, RAx, RBx v 2532-CTO, 11x, 62x, 6Dx, 77x v 2532-M1x, M9x, MDx, MSx, MTx, MUx N (continued) 162 MT 2529, 2530, 2531, 2532 Parts list No. FRU P/N CRU ID 3 Hinge, silver 26R9668 v 2529-CTO, 1Hx, E9x, EAx, EBx, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FTx, GAx, GBx, GCx v 2529-H1x, H4x, H9x, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HSx, HTx, L2x, P3x, P6x, P7x, P8x, P9x, R3x, R6x, R7x, R8x, R9x, RCx v 2530-CTO, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Ax, 2Ex, 38x, 3Ex, 3Gx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 4Ax, 4Bx, 4Cx, 4Dx, 54x, 56x, 58x, 59x, 5Bx, E9x, EBx v 2530-J1x, J2x, J7x, J8x, JBx, JDx, JEx, JFx, JTx, JVx, K1x, K2x, K3x, K4x, K8x, K9x, L1x, L2x, L3x, L4x, L5x, L8x, LCx, R7x, R8x v 2531-CTO, 38x, 3Jx, 3Kx, 71x, 76x, E9x v 2531-M5x, M6x, M7x, M8x, MAx, MBx, MCx, R7x v 2532-CTO, 38x, 3Jx, E9x v 2532-MCx N 4 Wireless WAN antenna cable (MAIN and AUX) v 2529-CTO v 2529-HUx, HWx v 2530-CTO, 36x, 37x v 2531-CTO v 2532-CTO N 91P6959 (continued) ThinkPad Z60m 163 Parts list No. FRU 5 LCD cover kit (black) 41V9793 v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, E7x, E8x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FFx, FMx, FPx, FQx, FRx, FSx, G1x, G2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x v 2529-H2x, H3x, H5x, H6x, H7x, H8x, HAx, HBx, HCx, HMx, HNx, HPx. HQx, HRx, HUx, HWx, P1x, P2x, R2x, R5x, RAx, RBx v 2530-CTO, 11x, 13x, 14x, 16x, 18x, 19x, 1Cx, 1Dx, 1Ex, 1Fx, 1Yx, 1Zx, 21x, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Cx, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 34x, 35x, 36x, 37x, 39x, 3Bx, 3Cx, 3Dx, 3Fx, 3Hx, 42x, 47x, 48x, 49x, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 51x, 52x, 53x, 55x, 57x, 5AxE4x, F2x v 2530-J3x, J4x, J5x, J6x, J9x, JAx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, JSx, K5x, K6x, K7x, KAx, KBx, L6x, L7x, L9x, LAx, LBx, LDx v 2531-CTO, 11x, 13x, 23x, 49x, 4Ex, 4Fx, 4Gx, 4Jx, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 77x, 78x, 79x, 7Ax, E1x v 2531-M1x, M2x, M3x, M4x, M9x, MDx, MGx, MJx, MKx, MSx, MTx, MUx, RAx, RBx v 2532-CTO, 11x, 62x, 6Dx, 77x v 2532-M1x, M9x, MDx, MSx, MTx, MUx (continued) 164 P/N MT 2529, 2530, 2531, 2532 CRU ID N Parts list No. FRU P/N CRU ID 5 LCD cover kit (silver) 26R9582 v 2529-CTO, 1Hx, E9x, EAx, EBx, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FTx, GAx, GBx, GCx v 2529-H1x, H4x, H9x, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HSx, HTx, L2x, P3x, P6x, P7x, P8x, P9x, R3x, R6x, R7x, R8x, R9x, RCx v 2530-CTO, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Ax, 2Ex, 38x, 3Ex, 3Gx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 43x, 44x, 46x, 4Ax, 4Bx, 4Cx, 4Dx, 54x, 56x, 58x, 59x, 5Bx, E9x, EBx v 2530-J1x, J2x, J7x, J8x, JBx, JDx, JEx, JFx, JTx, JVx, K1x, K2x, K3x, K4x, K8x, K9x, L1x, L2x, L3x, L4x, L5x, L8x, LCx, R7x, R8x v 2531-CTO, 38x, 3Jx, 3Kx, 71x, 76x, E9x v 2531-M5x, M6x, M7x, M8x, MAx, MBx, MCx, R7x v 2532-CTO, 38x, 3Jx, E9x v 2532-MCx N 6 Wireless LAN antenna cable 91P6958 N 7 LCD cable assembly, 15.4-in. WXGA 91P6957 N 8 Inverter card, WXGA (Sumida) 39T5620 N Inverter card, WXGA (Foxconn) 39T5635 N 9 Bluetooth daughter card (BDC-2) 39T0497 v 2529-CTO, 1Hx, E9x, EAx, EBx, F8x, F9x, FAx, FBx, FCx, FEx, FGx, FHx, FJx, FKx, FLx, FQx, FRx, FSx, FTx, GAx, GBx, GCx v 2529-H1x, H4x, H5x, H7x, H8x, H9x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HQx, HRx, HSx, HTx, HUx, HWx, RCx v 2530-CTO, 1Gx, 1Hx, 1Jx, 34x, 36x, 37x, 38x, 39x, 3Jx, 3Kx, 3Mx, 3Nx, 42x, 43x, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, E9x, EBx v 2530-J6x, J7x, J8x, JRx, JSx, JTx, JVx, K1x, K2x, K3x, K4x, K5x, K6x, K7x v 2531-CTO, 38x, 3Jx, 49x, 4Fx, 6Ax, 3Kx, 71x, 76x, 77x, 78x, E9x v 2531-M1x, M2x, M3x, M4x, M5x, M6x, M7x, M8x, M9x, MAx, MBx, MCx, MTx v 2532-CTO, 38x, 3Jx, 88x, E9x v 2532-M1x, M9x, MCx, MTx N 10 Clear plate kit N 26R9584 ThinkPad Z60m 165 Parts list Keyboard Language P/N (NMB) P/N (ALPS) P/N (Chicony) CRU ID Arabic 39T0961 39T7121 39T7181 ** Belgian 39T0962 39T7122 39T7182 Canadian, multilanguage (445) 39T0959 39T7119 39T7179 Chinese, Traditional 39T0985 39T7145 39T7205 Czech 39T0963 39T7123 39T7183 Danish 39T0964 39T7124 39T7184 Dutch 39T0972 39T7132 39T7192 English, U.K. 39T0982 39T7142 39T7202 English, U.S. 39T0958 39T7118 39T7178 English, U.S. (International, with a Euro symbol) 39T0983 39T7143 39T7203 Finnish, Swedish 39T0979 39T7139 39T7199 French, Canadian (058) 39T0960 39T7120 39T7009 French, European 39T0966 39T7126 39T7186 German 39T0967 39T7127 39T7187 Greek 39T0968 39T7128 39T7188 Hebrew 39T0970 39T7130 39T7190 Hungarian 39T0969 39T7003 39T7189 Italian 39T0971 39T7131 39T7191 Japanese 39T0984 39T7144 39T7010 Korean 39T7213 39T7215 39T7011 Norwegian 39T0973 39T7004 39T7193 Polish 39T0974 39T7134 39T7194 Portuguese 39T0975 39T7135 39T7195 Russian 39T0976 39T7136 39T7196 Slovak 39T0977 39T7005 39T7197 Slovenian 39T0978 39T7006 39T7198 Spanish, European 39T0965 39T7002 39T7185 Spanish, Latin American 39T0987 39T7147 39T7008 Swiss 39T0980 39T7007 39T7200 Thai 39T0986 39T7146 39T7206 Turkish 39T0981 39T7141 39T7201 166 MT 2529, 2530, 2531, 2532 Parts list Recovery CDs Windows XP Professional Windows XP Professional is preinstalled as the operating system in the following models: v 2529-CTO, E1x, E2x, E3x, E5x, E6x, E7x, E8x, E9x, EAx, F2x, F4x, F6x, F7x, F8x, FAx, FCx, FFx, FGx, FKx, FLx, FMx, FPx, Fx v 2529-H1x, H3x, H4x, H5x, H8x, H9x, HCx, HGx, HJx, HPx, HQx, HRx, HUx, HWx, R2x, R3x, R5x, R6x, R7x, R8x, R9x, RAx, RBx, RCx v 2530-CTO, 11x, 13x, 18x, 19x, 1Fx, 1Kx, 1Nx, 21x, 25x, 26x, 27x, 28x, 2Ax, 2Bx, 2Cx, 2Ex, 34x, 35x, 36x, 37x, 38x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 42x, 43x, 44x, 46x, 48x, 49x, 4Bx, 4Cx, 4Hx, 4Lx, 4Mx, 4Nx, 4Px, E9x, F2x v 2530-J1x, J2x, J3x, J4x, J9x, JAx, JBx, JDx, JGx, JHx, JSx, JTx, JVx, K8x, K9x, KAx, KBx, R7x, R8x v 2531-CTO, 11x, 13x, 38x, 3Jx, 3Kx, 49x, 4Qx, 62x, 68x, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 75x, 76x, 77x, 78x, 79x, 7Ax, E1x, E9x v 2531-M1x, M2x, M3x, M4x, M5x, M6x, M7x, M8x, MAx, MBx, MCx, MDx, MGx, MJx, MKx, MSx, MTx, MUx, R7x, RAx, RBx v 2532-CTO, 11x, 38x, 3Jx, 62x, 6Dx, 77x, E9x v 2532-M1x, MCx, MDx, MSx, MTx, MUx ThinkPad Z60m 167 Parts list Language P/N CRU ID Arabic 42J5258 * Chinese, Simplified 42J5251 Chinese, Traditional 42J5252 Chinese, Traditional (Hong Kong S.A.R.) 42J5253 Czech 42J5257 Danish 42J5247 Dutch 42J5250 English, Russia 42J5240 English, U.K. 42J5239 English, U.S. 42J5238 Finnish 42J5248 French 42J5241 German 42J5242 Greek 42J5262 Hebrew 42J5255 Hungarian 42J5261 Italian 42J5244 Japanese 42J5254 Korean 42J5263 Norwegian 42J5249 Polish 42J5256 Portuguese, Brazilian 42J5245 Russian 42J5259 Slovak 42J5264 Spanish 42J5243 Swedish 42J5246 Turkish 42J5260 168 MT 2529, 2530, 2531, 2532 Parts list Windows XP Home Edition Windows XP Home Edition is preinstalled as the operating system in the following models: v 2529-CTO, 1Hx, E4x, EBx, F1x, F3x, F5x, F9x, FBx, FEx, FHx, FJx, FQx, FRx, FTx v 2529-H2x, H6x, H7x, HAx, HBx, HDx, HEx, HFx, HHx, HKx, HLx, HMx, HNx, HSx, HTx v 2530-CTO, 14x, 16x, 1Cx, 1Dx, 1Ex, 1Gx, 1Hx, 1Jx, 1Mx, 1Yx, 1Zx, 22x, 23x, 24x, 29x, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 3Bx, 47x, 4Ax, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, E4x, EBx v 2530-J5x, J6x, J7x, J8x, JEx, JFx, JKx, JLx, JMx, JNx, JPx, JQx, JRx, K1x, K2x, K3x, K4x, K5x, K6x, K7x v 2531-CTO, 23x, 4Ex, 4Fx, 4Gx, 4Jx, 71x v 2531-M9x v 2532-CTO v 2532-M9x ThinkPad Z60m 169 Parts list Language P/N CRU ID Arabic 42J5474 * Chinese, Simplified 42J5467 Chinese, Traditional 42J5468 Chinese, Traditional (Hong Kong S.A.R.) 42J5469 Czech 42J5473 Danish 42J5463 Dutch 42J5466 English, Russia 42J5456 English, U.K. 42J5455 English, U.S. 42J5454 Finnish 42J5464 French 42J5457 German 42J5458 Greek 42J5478 Hebrew 42J5471 Hungarian 42J5477 Italian 42J5460 Japanese 42J5470 Korean 42J5479 Norwegian 42J5465 Polish 42J5472 Portuguese, Brazilian 42J5461 Russian 42J5475 Spanish 42J5459 Swedish 42J5462 Turkish 42J5476 170 MT 2529, 2530, 2531, 2532 Parts list Miscellaneous parts FRU P/N CRU ID Screw kit (including nylon-coated screws): v M2 × 3 mm-I (BNI, NYLOK) (25) v M2 × 5 mm-I (BNI, NYLOK) (31) v M2 × 5 mm-F (BNI, NYLOK) (2) v M2 × 9 mm-I (BNI, NYLOK) (5) v M2 × 17 mm-I (BNI, NYLOK) (7) v M3 × 4 mm-P (BNI, NYLOK) (1) v M3 × 2.8 mm-I (BNI, D6.2, T2.0) (1) v Hex stud (2) 26R9579 N System miscellaneous parts: v (a) DC in cable v RJ11 cable v RJ11 cap v Connector bag 26R9578 N Base miscellaneous parts: v Rubber foot v Insulation sheet v Gasket v ODD eject mech parts v PC Card slot door v Coil spring 26R9577 N System board miscellaneous parts: v Mylar v Gasket v Sheetmetaled mech parts v (b) CPU support plate v (c) MDC cable 26R9576 N 26R9580 N Note: Italicized letters in parentheses are references to the exploded view on page 140. Note: Italicized letters in parentheses are references to the exploded view on page 140. LCD assembly miscellaneous parts: v (a) LCD latch L v (b) Coil spring v (c) Link wire v (d) LCD latch R v (e) Cable bush v EMI metal sheet v WAN antenna cover Note: Italicized letters in parentheses are references to the exploded view on page 160. ThinkPad Z60m 171 Parts list AC adapters FRU P/N CRU ID 3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxV)
OP ASTEC 92P1104 * Lite-On 92P1108 * Sanken 92P1112 * 2-pin (90W, 20 V) slim adapter for non-PFC model (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
OP ASTEC 92P1106 * Lite-On 92P1110 * Sanken 92P1114 * FRU P/N CRU ID Ultrabay Slim battery (2nd bay battery)
R 40Y6790 * SATA hard disk drive adapter, 9.5 mm 26R9246 * ThinkPad Advanced Dock 26R9061 * ThinkPad Advanced Mini Dock 26R9063 * ThinkPad Essential Port Replicator 26R9065 * Ultrabay Slim hard disk drive adapter 62P4553 * Ultrabay Slim Li Polymer battery (2nd bay battery), Sanyo (WW) 08K8191 * Multiple battery charger 02K6642 * Diskette drive cable 27L0525 * Diskette drive (TEAC) 08K9606 * Diskette drive (Sony) 08K9607 * Optional FRUs 172 MT 2529, 2530, 2531, 2532 Parts list Common parts list Tools Tool P/N Triconnector wrap plug 72X8546 PC test card 35G4680 Audio wrap cable 66G5180 USB parallel test cable 05K2580 Screwdriver kit 95F3598 Mini PC tool set 00P7033 1/4" drive spinner handle 1650840 1/4" Sq. to 1/4" hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB floppy diskette drive for maintenance diskette 05K9283 PCI-Express/USB wrap card 27K9813 USB floppy diskette drive tool kit 27L3452 ThinkPad Hardware Maintenance Diskette Version 1.73 or later Note: Download the file from the following Web site: http://www.lenovo.com/think/spm — ThinkPad Z60m 173 Parts list Power cords (system) A ThinkPad power cord for a specific country or region is usually available only in that country or region: For 2-pin power cords: Region P/N CRU ID Canada, U.S.
R v models -CTO, xxF, xxL, xxS, xxU 39M5016 * Japan
R v models -Exx, Jxx 39M5040 Argentina
R v models -CTO, xxY 39M5020 Brazil
R v models -CTO, xxP 39M5056 For 3-pin power cords: Region P/N CRU ID Australia, New Zealand
R v models -CTO, xxG, xxM 39M4960 * Taiwan, Thailand
R v models -CTO, xxV 39M4955 Italy
R v models -CTO, xxG 39M4984 Denmark
R v models -CTO, xxG 39M4968 U.K., China (Hong Kong S.A.R.)
R v models -CTO, xxB, xxG, xxH 39M4976 European countries
R v models -CTO, xxG 39M4964 India, South Africa
R v models -CTO, xxG 39M4972 Israel
R v models -CTO, xxG 39M4988 Korea
R v models -xxK 39M5000 China (P.R.C.) (other than Hong Kong S.A.R.)
R v models -xxC 39M4996 Switzerland
R v models -CTO, xxG 39M4980 174 MT 2529, 2530, 2531, 2532 Notices Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to: Lenovo (United States), Inc. 500 Park Offices Drive, Hwy. 54 Research Triangle Park, NC 27709 U.S.A. Attention: Lenovo Director of Licensing LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments ThinkPad Z60m 175 Notices and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. 176 MT 2529, 2530, 2531, 2532 Trademarks Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo Rescue and Recovery ThinkLight ThinkPad ThinkPad Advanced Dock ThinkPad Advanced Mini Dock ThinkPad Port Replicator ThinkPad Essential Port Replicator ThinkVantage TrackPoint Ultrabay Ultrabay 2000 Ultrabay Plus UltraNav The following terms are trademarks of the International Business Machines Corporation in the United States, other countries, or both: IBM (used under license) Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in the United States, other countries, or both. Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Other company, product, or service names may be the trademarks or service marks of others. ThinkPad Z60m 177 Part Number: 39T6195 (1P) P/N: 39T6195