Transcript
Engine Technical Data Unit General Data Number of Cylinders Engine Type Bore x Stroke Total Displacement Combustion type Aspiration Valves per Cylinder Compression ratio Firing Order
3TNV82A-DSA
3TNV82A-DSA3
3TNV82A-DSA2
mm x mm cc -
3 Inline, Water-Cooled, 4 Stroke Diesel 82 x 84 1330 Direct Injection Naturally Aspirated 2 19.2 1-3-2
Net Intermittent Power
HP [kW] / rpm]
30.2 [22.5]/3000
Net Continuous Power
HP [kW] / rpm]
--
Net Max Torque
ft-lb [Nm]/rpm
63.9 [86.6]/1200
Low Idle Speed
rpm
1000+/-25
High Idle Speed
rpm
3180+/-25
BMEP, Net Power
Psi [kPa]
96.0 [676]
BMEP, Cont. Power
Psi [kPa]
--
Performance Data
Physical Data Direction of rotation Length - Inches Width - Inches Height - Inches Dry Weight Center of Gravity: From Rear Face of Block From Crankshaft to Exhaust Side Above Crankshaft
Inches [mm] Inches [mm] Inches [mm] lbs [kg] Inches [mm] Inches [mm] Inches [mm]
22.99 [584]
313 [142]
5.04 [128] 0.37 [9.5] 3.23 [82]
PTO System Flywheel
-
SAE #5
Flywheel Housing
-
SAE #5 (Depth 124)
Gear Case
-
Lubrication System Inclination, Continuous Inclination, 3 minutes Max. Oil Pan Style Lubrication Oil Filter Type Temperature Limit ( main oil pressure passage) Nominal Oil Pressure Oil Capacity, Effective Total System Capacity Oil Change Interval, Hours Recommended Oil Type
Date: October 29, 2003 Doc. No.: YAE-Spec-03-0010 Page: 1/2
Counter Clockwise (view from flywheel) 21.26 [540] 20.94 [532] 20.0 [508] 24.02 [610] 288 [131] 273 [124]
Semi SAE #5 Semi SAE #5 Semi SAE #5 Back Plate (Depth 80) with SAE Hydraulic Pump Flange
degree degree -
30 35 Deep Paper Element
°F [℃]
248 [120]
psi [kgf/cm2] Liters Liters hr API
64 [4.5] 1.9 5.5 250 (50, initial) CD, CF or higher grade
Engine Technical Data Unit Cooling System Fan Type Fan Diameter Number of Blades Fan Pulley Diameter Crank Pulley Diameter Fan Spacer Thickness - Inches [mm] Max. Coolant Temp. Thermostat Starts Opening Thermostat Fully Open Coolant Capacity (Engine) Coolant Flow (C. W. Pump) Heat Rejection at Rated Power Fuel System Fuel Filter Type Fuel Injection Pump Type Water Separator (Standard) Max. Suction Head (Fuel pickup to Injection pump) Fuel Feed Pump Type Fuel Flow (Feed pump) Max. Allowable Fuel Temperature Required Separation Distance Between Pickup & Return Fuel Consumption at Net Inter. Power
3TNV82A-DSA
3TNV82A-DSA3
3TNV82A-DSA2
Inches [mm] Inches [mm] Inches [mm] Inches [mm] °F [℃] °F [℃] °F [℃] Liters Liters / min BTU/hr [kcal/hr]
Puller 13.19 [335] 5 4.33 [110] 4.33 [110] 0.71 [18] 221 [105] 160±2.7 [71 ± 1.5] 185 [85] 1.8 40.5
-
Paper Element Distributor Type Mesh size: 100-mesh/inch, water reservoir 150 cc
Inches [mm]
40 [1000]
Liters / hr ° F [°C]
Electrical 176 [80] Fuel Injection Pump inlet
Inches [mm]
min. 4 [100]
lb/hp-hr [g/kW-hr]
0.42 [258]
Inch Aq [kPa]
11.8 [2.9]
Inch Aq [kPa]
25 [6.2]
ft^3 / min. [m^3 /min]
Closed
56000 [14100]
60
Intake System Max. Air Intake Restriction, initial Max. Air Intake Restriction, replace element Crankcase Ventilation Type Engine Air Flow (For sizing air cleaner) Exhaust System Max. Allowable Back Pressure, initial Max. Allowable Back Pressure, cleaning
109 [3.1]@3000 rpm
Inch Aq [kPa]
51.1 [12.7]
Inch Aq [kPa]
61.4 [15.3]
Exhaust Air Flow @ Max. Power Exhaust Temp. Exhaust Temperature at Max. Power Exhaust Temperature at Max. Torque
ft^3/ min. [m³/min] ° F [°C] ° F [°C]
1202 [650] 968 [520]
Electrical System System Voltage Electric Stop Device Alternator Starting Aid Device Standard pre-heat time Engine Block Heater Port Starting Motor Type Starting Motor Power Maximum Starter Cable Resistance Maximum Battery Cable Resistance
Volts Seconds kW Ohm (Ω) Ohm (Ω)
12 V Stop Solenoid 12V-40A Air Heater, 12V 400W 15 Exhaust Side Reduction 1.7 0.05 0.002
History: Revision 2, 07/19/2004 Rearraned table Corrected the Exhaust Air Flow @32 oF(0 oC) to Max. Power Exhaust Temp.
Date: October 29, 2003 Doc. No.: YAE-Spec-03-0010 Page: 2/2
251 [7.1]
Manager
S. Manager
Revision: 2 Written by
